Search NASA⌕ Search

SEARCH · Search NASA

Results for “elevated pressure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Numerical Investigation of the characteristics of pressurized biomass-oxy-combustion

As a second generation of oxy-fuel combustion technologies, pressurized oxy-combustion has a potential to improve the process efficiency and economy. With the modern decarbonization needs, biomass combustion is considered to be nearly CO2 neutral, and thus co-firing biomass with coal in an oxy-combustion process can achieve a negative CO2 balance. The size of the biomass fuel particles is a key parameter in an entrained flow combustor because large biomass particles, exceeding some threshold size, may only partially be burnt due to the restrictions on the heat transport, thereby diminishing the combustion efficiency. While such a threshold particle size has been scrutinized at an atmospheric pressure, the present study extends the analysis to elevated pressures. Specifically, two scenarios were set up, for experimental-scale and full-scale pressurized oxy-combustors, with the threshold sizes of biomass particles appearing 0.5 mm and 5 mm, respectively, without temperature gradient in biomass particles. With temperature gradient, the parametric study included the particles in the range from 0.15 mm to 5 mm. It is shown that the thermal-thin model is applicable to spherical biomass particles not exceeding 0.15 mm. The impact of the heating rate on biomass particle devolatilization was also investigated and the biomass devolatilization could happen in less than 1 second; the same amount of heat energy could induce different volatile release rates.

Li, Lei↗
DOE OSTI2021

Design and Experimental Demonstration of an Additive Manufactured Smart Oxy-Methane Burner for High Pressure and Supercritical Combustion

Pressurized oxy combustion-based systems can improve efficiency by recovering latent heat of the steam in the Flue Gas and achieving 90% CO2 capture. In addition, the novel Directly Heated Supercritical Carbon Dioxide (DH-SCO2) power cycles can achieve high thermal efficiencies and provide nearly full carbon capture. Additionally, due to the reduction of flue gas at higher pressure, smaller system size and capital cost reductions are also possible. Recent thermodynamic analysis of the DH-SCO2 cycle performed by the UTEP research team shows that combustion conditions in the vicinity of 300 bar pressure and 1000-1400 K temperature allow for relatively high system efficiencies while operating within the limit of available combustor materials. However, the realization of a directly heated supercritical power cycle requires combustion systems to operate in supercritical conditions and at temperature far below the blowout limit of conventional flames (above 1500 K). The thermodynamic properties along with the combustion properties and kinetics are unexplored at such conditions. Additionally, the interaction of the supercritical environment with energy components is also unknown. High-pressure combustion tests are performed using a smart burner at some intermediate pressure ranges (<20 bar) to help minimize these knowledge gaps. The knowledge obtained from the high-pressure test will assist in understanding the combustion chamber pressurization mechanism, ignition and flame behavior at the elevated pressure. The obtained data will act as a systematic first step in testing at higher pressures of 100 and 300 bar pressures.The primary purpose of this Dissertation is to demonstrate the operability of a low NOx smart burner for oxy-methane combustion at high pressure (< 20 bar) and scalable up to supercritical conditions. A shear co-axial smart burner is designed with a real-time temperature monitoring capability to understand the burner face interaction at high-pressure conditions. In addition, the burner has four independent injection ports to allow the independent injection of fuel and dilution gases in the combustor. The maximum operating capability of the burner is 575 kWth. The burner was fabricated using a Laser Powder Bed Fusion process with Nickel Alloy 718. A powder removal technology was invented comprising ultrasonic vibration, liquid nitrogen exposure and media blasting to remove powders from internal channels of the burner. The burner operability tests are performed in the high-pressure combustor and the swirl combustor. The high-pressure combustor was used to investigate the burner operability and thermal soak back at different pressurized conditions. The experimental tests in high-pressure combustor up to 275 kWth input resulted in 16.5 bar chamber pressure and 198°C thermal soaks back to the burner. The burner was capable of providing the required thermal input within a 3% deviation range. In addition, soot formation occurred at high-pressure tests. The swirl combustor was used to observe the flame stability of the burner. Flame lift-off was observed for jet velocities above 450 m/s. Additionally, lift-off decreased for low co-flow velocities. CO2 dilution experiments showed increased flame instabilities for all conditions above 50% dilution ratios. At lower thermal inputs, partial flame blow-offs occurred for dilution ratios above 50%. All conditions significantly reduced the flame temperature and increased the flame lift-off height. Finally, a 2nd generation AM smart burner was designed using the knowledge from the 1st generation burner experiments. The 2nd generation burner incorporated two sets of swirlers with 0.9 swirl no. A cooling system was also designed for long-duration tests at higher pressures. The thermal input and division of the burner's power are kept the same as the 1st generation burner. The burner is to be fabricated using nickel-alloy 718 for high-pressure handling capability. The design can sustain at high-pressure conditions up to 100 bar.

Islam, Md Nawshad Arslan↗
DOE OSTI2024

All-digital Sensor System for Distributed Downhole Pressure Monitoring in Unconventional Fields

This project developed and validated (through field tests) a new low-cost all-digital pressure sensing technology for in situ distributed downhole pressure monitoring in unconventional oil and gas (UOG) fields. The all-digital sensing technology uses a built-in non-electric analog-to-digital converter (ADC) to transform the pressure information into a combination of binary (ON/OFF) states. As such, the system does not need downhole electronics for signal conditioning and telemetry. The all-digital sensors can be remotely logged over a long distance, and many sensors can be multiplexed for distributed sensing. Based on a review of unconventional wells in the Lower 48 states, the specification of the sensor is to measure pressure up to 69 MPa (10,000 psi) and temperature up to 250°C. A sensor with a helical bourdon sensing element and a digital signal decoder of 50 mm diameter and 109 mm length was constructed. The helical bourdon sensing element was made of 304L stainless steel and filled with motor oil. The digital converter was made up of 8 digital reading pads constructed of high-temperature epoxy with conductive inserts made of stainless steel. The sensor had a linear response to pressure with an accuracy of 0.14 MPa (20 psi). To withstand the high pressure, the sensor was enclosed in a stainless-steel pressure housing with a wall thickness of 5.5 mm, a diameter of 73 mm, and a length of 724 mm. In the laboratory tests, the sensor exhibited no temperature-related effects on the results. The sensor did not show drift over a 14-day test period at elevated pressure. A field test was conducted where the sensor was deployed in a test wellbore at the Quest drilling test facility to a depth of 0 feet over three weeks. The sensor was attached to the production rods, along with a downhole reference sensor of PPS27 type, which is a permanent downhole monitoring system. During the testing phase, the test well annular blow-out preventer was closed, and the well was pressurized at the surface to 11 MPa (1600 psi). The sensor read the elevated bottom hole pressure of 1500 psi. A multiplexing unit was created for the sensor to deploy multiple sensors on one data transmission line in a distributed approach. The multiplexing unit was tested in a simulated environment of 3048 m (10,000 ft) with five sensors distributed. The sensors were pressurized at different intervals. The multiplexed sensors recorded the correct pressure, and the multiplexing did not interfere with the readings. The proposed concept of an all-digital pressure sensor for harsh downhole environments was designed, manufactured, and tested in the laboratory and tested at the field to a up to 69 MPa and 250°C. This technology has high-temperature tolerance and has potential in downhole areas outside oil and gas, such as carbon capture and storage (CCS) and geothermal wells. The sensor concept has been proven in this project, but to create a commercially viable product, manufacturing a sensor with a smaller diameter needs to be performed.

02 PETROLEUM↗
DOE OSTI2021

End-gas autoignition fraction and flame propagation rate in laser-ignited primary reference fuel mixtures at elevated temperature and pressure

Knock in spark-ignited (SI) engines is initiated by autoignition of the unburned gasses upstream of spark-ignited, propagating, turbulent premixed flames. Knock propensity of fuel/air mixtures is typically quantified using research octane number (RON), motor octane number (MON), or methane number (MN; for gaseous fuels), which are measured using single-cylinder, variable compression ratio engines. In this study, knock propensity of SI fuels was quantified via observations of end-gas autoignition (EGAI) in unburned gasses upstream of laser-ignited, premixed flames at elevated pressures and temperatures in a rapid compression machine. Stoichiometric primary reference fuel (PRF; n-heptane/isooctane) blends of varying reactivity (50 ≤ PRF ≤ 100) were ignited using an Nd:YAG laser over a range of temperatures and pressures, all in excess of 545 K and 16.1 bar. Laser ignition produced outwardly-propagating premixed flames. High-speed pressure measurements and schlieren images indicated the presence of EGAI. The fraction of the total heat release attributed to EGAI (i.e., EGAI fraction) varied with fuel reactivity (i.e., octane number) and the time-integrated temperature of the end-gas prior to ignition. Flame propagation rates, which were measured using schlieren images, were only weakly correlated with octane number but were affected by turbulence caused by variation in piston timing. Under conditions of low turbulence, measured flame propagation rates approached one-dimensional premixed laminar flame speed computations performed at the same conditions. Experiments were simulated with a three-dimensional CONVERGE™ model using reduced chemical kinetics (121 species, 538 reactions). The simulations accurately captured the measured flame propagation rates, as well as the variation in EGAI fraction with fuel reactivity and time-integrated end-gas temperature. The simulations also revealed low-temperature heat release as well as formaldehyde and hydrogen peroxide formation in the end-gas upstream of the propagating flame, which increased the temperature and degree of chain branching in the end-gas, ultimately leading to EGAI.

42 ENGINEERING↗
DOE OSTI2021

Rock Fracturing Using High-Pressure Ethylene/Nitrous Oxide Detonations

The present work investigates high initial pressure detonations of a stoichiometric mixture of ethylene and nitrous oxide (C2H4 + 6N2O) as a method of fracturing rock beneath the ground surface. These tests were conducted at a test site operated by the Energetic Materials Research and Testing Center (EMRTC), Socorro, New Mexico. The volume under the surface used for testing (called the Down Hole Assembly) consists of a 0.438 in. ID x 50 ft. long stainless-steel tube running down from the test site to a well bore which is 3 in. ID x 10 ft. long and the rock in the well bore is exposed to the propagating combustion wave. The testing carried out at Zucrow Laboratories in the smaller, alloy steel combustion vessel provided a scaling of pressures expected in the well bore. The combustion is initiated by energizing an EBW (Exploding Bridge Wire) above the ground surface. The experimental setup accommodates one high pressure (100,000 psia) transducer to measure the pressure peak and is placed approximately 5 ft. above the ground surface and 5 ft. downstream of the EBW. The focus of this series of experiments is to investigate the dependence of fracture to the rock beneath the surface on initial pressures of the mixture of ethylene and nitrous oxide. Experiments were carried out at initial pressures varying between 125 psia and 300 psi. The transducer recorded elevated pressures, which were 2.3 to 2.6 times in excess of the CJ values. The experimental results are discussed and explained in this report.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured H282 in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in high temperature and pressure direct-fired supercritical CO2 power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can result in additional corrosion behaviors. Utilizing additive manufacturing (AM) methods for construction of power cycle components requiring both compact and complex designs could be advantageous. AM H282 produced by laser powder bed fusion was exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure and supercritical conditions (20 MPa) for up to 4,000 hours. Oxidation behavior, sub-surface carbide formation, and chromia scale volatilization was dependent upon AM preparation techniques and surface modifications. These results are discussed in terms of the potential compatibility issues that may arise when using AM alloys in high temperature regions of direct-fired sCO2 power cycles, particularly for thin-walled components.

Carney, Casey↗
DOE OSTI2023

Investigation of the High-Pressure Behaviors of Amblygonite by Single-Crystal X-ray Diffraction, Raman Spectroscopy, and DFT Calculations

In the present study, we extensively explored the high-pressure behaviors and vibrational properties of amblygonite LiAlPO 4 F with elevated pressures up to 34.3 GPa based on single-crystal X-ray diffraction measurements, Raman spectroscopy, and DFT calculations. The compressibility and elastic properties of amblygonite were determined first. Specifically, the obtained isothermal bulk modulus of LiAlPO 4 F is 128(4) GPa and the triclinic phase exhibited anisotropic compression with axial compressibility β c > β a > β b with a ratio of 1.11:1.00:1.20. The Raman spectra showed no indication of phase transformation and were used to obtained mode Grüneisen parameters. The average Grüneisen parameter for PO 4 tetrahedral sites was smaller than for the LiO 4 F sites. Our results provide new insights into the phase stability and elastic properties of lithium-fluorite granites at extreme conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tuning Strong Metal–Support Interaction Kinetics on Pt-Loaded TiO 2 (110) by Choosing the Pressure: A Combined Ultrahigh Vacuum/Near-Ambient Pressure XPS Study

Pt catalyst particles on reducible oxide supports often change their activity significantly at elevated temperatures due to the strong metal–support interaction (SMSI), which induces the formation of an encapsulation layer around the noble metal particles. However, the impact of oxidizing and reducing treatments at elevated pressures on this encapsulation layer remains controversial, partly due to the “pressure gap” between surface science studies and applied catalysis. In the present work, we employ synchrotron-based near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS) to study the effect of O 2 and H 2 on the SMSI-state of well-defined Pt/TiO 2 (110) catalysts at pressures of up to 0.1 Torr. Further, by tuning the O 2 pressure, we can either selectively oxidize the TiO 2 support or both the support and the Pt particles. Catalyzed by metallic Pt, the encapsulating oxide overlayer grows rapidly in 1 × 10 –5 Torr O 2 , but orders of magnitude less effectively at higher O 2 pressures, where Pt is in an oxidic state. While the oxidation/reduction of Pt particles is reversible, they remain embedded in the support once encapsulation has occurred.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Pt Particles on a Dynamic TiO 2 Support in Near-Ambient Conditions−Disentangling Size, Pressure, and Support Effects

Platinum particles on reducible oxides are known to form complex and highly dynamic catalyst systems at elevated pressures and temperatures, often adopting active structures that differ from those found at room temperature and under ultrahigh vacuum (UHV). Here, we study the oxidation and structural evolution of subnanometer Pt clusters and nanoparticles supported on rutile TiO 2 (110) across an oxygen pressure range from UHV to 0.1 mbar, using near-ambient pressure X-ray photoelectron spectroscopy (NAP-XPS), scanning tunneling microscopy (STM) under UHV and NAP conditions, and low-energy ion scattering (LEIS). Our results reveal distinct differences in oxidation behavior and thermal stability between Pt nanoparticles and clusters, which are further modulated by the support stoichiometry and oxygen pressure. Small Pt clusters become oxidized even at room temperature but are susceptible to accelerated sintering in 0.1 mbar O 2 at elevated temperatures. In contrast, well-crystallized Pt nanoparticles on near-stoichiometric TiO 2 show weaker oxidation. On a reduced, defective TiO 2 support, Pt instead quickly becomes deeply buried by new titania layers, which are formed during support reoxidation. This process appears to result primarily from interactions of the support with the gas phase, unlike the classical, selflimited encapsulation that is induced by the strong metal−support interaction (SMSI). Finally, we address the full complexity of real catalysts in a direct side-by-side comparison of the single-crystalline model system with a Pt-loaded TiO 2 powder catalyst (P25). We conclude that the stoichiometry of the model supports must be carefully chosen and controlled to accurately reproduce the expected state of powder supports during redox reactions.

metal nanoparticles↗
DOE OSTI2022

High critical field superconductivity at ambient pressure in MoB 2 stabilized in the P6/mmm structure via Nb substitution

Recently it was discovered that, under elevated pressures, MoB 2 exhibits superconductivity at a critical temperature T c as high as 32 K. The superconductivity appears to develop following a pressure-induced structural transition from the ambient pressure $\text{R}\bar{3}$⁢m structure to an MgB 2 -like P6/mmm structure. This suggests that remarkably high T c values among diborides are not restricted to MgB 2 as previously appeared to be the case, and that similarly high T c values may occur in other diborides if they can be coerced into the MgB 2 structure. In this paper, we show that density functional theory calculations indicate that phonon free energy stabilizes the P6/mmm structure over the $\text{R}\bar{3}$⁢m at high temperatures across the Nb 1–x ⁢Mo x B 2 series. X-ray diffraction confirms that the synthesized Nb-substituted MoB 2 adopts the MgB 2 crystal structure. Finally, high magnetic field electrical resistivity measurements and specific heat measurements demonstrate that Nb x ⁢Mo 1–x⁢ B 2 exhibits superconductivity with T c as high as 8 K and critical fields approaching 6 T.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Computational Identification and Experimental Demonstration of High‐Performance Methane Sorbents

Abstract Remarkable methane uptake is demonstrated experimentally in three metal‐organic frameworks (MOFs) identified by computational screening: UTSA‐76, UMCM‐152 and DUT‐23‐Cu. These MOFs outperform the benchmark sorbent, HKUST‐1, both volumetrically and gravimetrically, under a pressure swing of 80 to 5 bar at 298 K. Although high uptake at elevated pressure is critical for achieving this performance, a low density of high‐affinity sites (coordinatively unsaturated metal centers) also contributes to a more complete release of stored gas at low pressure. The identification of these MOFs facilitates the efficient storage of natural gas via adsorption and provides further evidence of the utility of computational screening in identifying overlooked sorbents.

Nath, Karabi↗
DOE OSTI2022

Computational Identification and Experimental Demonstration of High‐Performance Methane Sorbents

Abstract Remarkable methane uptake is demonstrated experimentally in three metal‐organic frameworks (MOFs) identified by computational screening: UTSA‐76, UMCM‐152 and DUT‐23‐Cu. These MOFs outperform the benchmark sorbent, HKUST‐1, both volumetrically and gravimetrically, under a pressure swing of 80 to 5 bar at 298 K. Although high uptake at elevated pressure is critical for achieving this performance, a low density of high‐affinity sites (coordinatively unsaturated metal centers) also contributes to a more complete release of stored gas at low pressure. The identification of these MOFs facilitates the efficient storage of natural gas via adsorption and provides further evidence of the utility of computational screening in identifying overlooked sorbents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Fiber Sorbents – A Versatile Platform for Sorption-Based Gas Separations

Increasing demand for high-purity fine chemicals and a drive for process intensification of large-scale separations have driven significant work on the development of highly engineered porous materials with promise for sorption-based separations. While sorptive separations in porous materials offer energy-efficient alternatives to longstanding thermal-based methods, the particulate nature of many of these sorbents has sometimes limited their large-scale deployment in high-throughput applications such as gas separations, for which the necessary high feed flow rates and gas velocities accrue prohibitive operational costs. These processability limitations have been historically addressed through powder shaping methods aimed at the fabrication of structured sorbent contactors based on pellets, beads or monoliths, commonly obtained as extrudates. These structures overcome limitations such as elevated pressure drops commonly recorded across powder adsorption beds but often accrue thermal limitations arising from elevated particle density and aggregation, which ultimately cap their maximum separation performance. Furthermore, the harsh mechanical strain to which powder particles are subjected during contactor fabrication, in the form of extrusion/compression forces, can result in partial pore occlusion and framework degradation, further limiting their performance. Here, we present the development of porous fiber sorbents as an alternative sorbent contactor design capable of addressing sorbent processability limitations while enabling an array of performance-maximizing heat integration capabilities. This new sorbent form factor leverages pre-existing know-how from hollow fiber spinning to produce fiber-shaped sorbent contactors through the phase inversion of known polymers in a process known as dry-jet/wet quenching. The process of phase inversion allows microporous sorbent particles to be latched onto a macroporous polymer matrix under mild processing conditions, thus making it compatible with soft porous materials prone to amorphization under traditional pelletization conditions. Sorbent fibers can be created with different geometries through control of the spinning apparatus and process, offering the possibility to produce monolithic and hollow fibers alike, the latter of which can be integrated with thermalization fluid flows. In this Account, we summarize our progress in the field of fiber sorbents from both design and application standpoints. We further guide the reader through the evolution of this field from the early inceptive work on zeolite hollow fibers to recent developments on MOF fibers. We highlight the versatile nature of fiber sorbents, both from the composition, fabrication and structure points of view, and further demonstrate how fiber sorbents offer alternative paths in tackling new and challenging chemical separation challenges like direct air capture (DAC), with a final perspective on the future of the field.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Heat Loss Effects on Emissions in an NH 3 RRQL Combustor

Ammonia (NH 3 ) is a carbon-free energy carrier with an infrastructure for production, storage, and distribution. There is interest in direct NH 3 combustion, but managing pollutant emissions is a key challenge, particularly nitric oxides (NO x ) due to the fuel-bound nitrogen atom, nitrous oxide (N 2 O), which is a potent greenhouse gas, and unburned NH 3 , which is harmful to humans and the environment. Rich staged combustor concepts with extended primary residence times (τ res,primary ), like Rich-Relax- Quick-mix-Lean (RRQL), offer a viable pathway for direct NH 3 combustion with low levels of NO x formation. However, minimizing secondary emissions such as N 2 O and unburned NH 3 and hydrogen (H 2 ) remains a critical challenge. Prior atmospheric-pressure studies have demonstrated that RRQL operation with sufficiently long τ res,primary enables substantial NO x relaxation and promotes NH 3 cracking to H 2 , if heat losses from the relaxation stage are limited. However, the combined influence of elevated pressure and long residence time on RRQL performance has not been explored. The present work examines RRQL operation at pressures up to 5 bar and elevated τ res,primary . Exhaust measurements of NO x , NH 3 , and N 2 O are used to quantify the extent of NO x relaxation and NH 3 cracking under nonadiabatic conditions. To contextualize and quantify the effects of heat losses in the experimental data, chemical reactor networks (CRNs) incorporating prescribed heat loss rates are employed to assess the sensitivity of emissions to thermal losses in the relaxation stage. Collectively, the results demonstrate that management and quantification of heat losses are essential to preserve NO x relaxation and limit NH 3 and N 2 O emissions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Stability of the peroxide group in BaO 2 under high pressure

Alkaline earth metal peroxides are typical examples of ionic compounds containing polyanions. We herein report a stable BaO 2 phase at high pressure up to 130 GPa found via a first-principles computational structure searches and high-pressure experimental investigations. The identified monoclinic structure (space group C2/m) can be derived by sublattice distortions of Ba atoms and peroxide groups associated with the phonon mode softening of the lower-pressure Cmmm structure. Contrary to the previous expectation of polymerization of the peroxide group at elevated pressure, the new phase retains the peroxide group and interestingly exhibits an insulating behavior demonstrating an increase of the band gap under compression. Our synchrotron XRD measurements could not distinguish between Cmmm and C2/m BaO 2 definitively because the difference in XRD patterns is very subtle. However, our data do not show any sign of polymerization transition up to 120 GPa. Raman spectra of the O-O peroxide vibration show a small anomaly in frequency at 110 GPa, which is qualitatively similar to that predicted theoretically due to the Cmmm to C2/m phase transition thus supporting the predicted transformation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Pressure-stable supported ionic liquid membranes using isoporous supports for evaluating pure- and mixed-gas light paraffin fractionation

Advances in horizontal drilling and hydraulic fracturing have spurred the growth of domestic U.S. energy production. Membranes, typically silicone rubbers, have found utility in shale gas treatment as fuel gas conditioning units to selectively remove C 2 + hydrocarbons at pressures up to 30 bar, producing clean CH 4 for gas engines. However, more selective materials could be beneficial for broader shale gas treatment applications, such as dew point control units. Supported ionic liquid membranes (SILMs) offer a potential opportunity for improving C 3 H 8 /CH 4 selectivity, but they lack pressure-stability. Here, we report C 3 H 8 /CH 4 selective and pressure-stable SILMs using isoporous supports. SILMs with supports that had minimal defects remained stable up to 15 bar of transmembrane pressure. This stability allowed for pure- and mixed-gas testing of the resulting membranes at elevated pressures. Furthermore, these tests revealed that low viscosity ILs (<100 cp) may display mixed-gas permeances and permselectivity nearly identical to pure-gas results. On the other hand, higher viscosity ILs may display increasing permeances and permselectivity with increasing C 3 H 8 fugacity, similar to rubbery polymers. Ultimately, the SILMs demonstrated relatively high pressure-stability due to the isoporous supports and competitive mixed-gas C 3 H 8 /CH 4 permselectivity compared to silicone rubber.

Rosenthal, Justin J. [University of Texas at Austi↗
DOE OSTI2020

Mechanism of the Accelerated Water Formation Reaction under Interfacial Confinement

Subnanoscale spaces at the interface between weakly coupled thin films and their metal supports offer exciting opportunities for studying chemical reactions under confinement. Here, we investigated the kinetics of water formation (from hydrogen and chemisorbed oxygen) in the confined space at the interface between bilayer (BL) silica and a Ru(0001) support, compared to the reaction on the bare Ru(0001) surface. Ambient pressure X-ray photoelectron spectroscopy (AP-XPS) experiments were carried out at different temperatures at elevated pressures of H 2 to follow the reaction kinetics. The apparent activation energy at the BL-silica/Ru(0001) interface was found to be 0.38 eV lower than that on bare Ru(0001), consistent with a recent report by Prieto et al. (Angew. Chem., Int. Ed.2018, 57(28), 8749–8753) carried out at lower H 2 pressures using low-energy electron microscopy. Density functional theory calculations revealed that the rate-limiting step in the direct hydrogenation pathway on the Ru(0001) surface is the first hydrogen addition step (*H + *O ↔ *OH). The confinement at the BL-silica/Ru(0001) interface only marginally affects the energy barrier of the first hydrogen addition. Instead, it activates an alternative disproportionation reaction pathway (*H 2 O + *O ↔ 2*OH). On the bare Ru(0001) surface, the disproportionation pathway can only occur at cryogenic temperatures or under high water vapor pressures. However, the presence of the BL-silica increases the desorption barrier for water molecules at the interface. The increased residence time allows trapped water molecules to react with chemisorbed oxygen to produce two *OH per H 2 O with an activation energy 0.25 eV lower than that of the first hydrogen addition step. Finally, this work reveals the origin of the observed accelerated water formation reaction at the BL-silica/Ru(0001) interface in the low-temperature regime (T < 350 K) and points to a route to engineer chemical reaction pathways by leveraging subnanoscale confined spaces at metal–oxide interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An experimental and kinetic modeling study of cyclopentane and dimethyl ether blends

Cyclopentane is a suitable naphthene, or cycloalkane, in a palette for multi-component gasoline surrogate fuels due to its presence in market fuels and its relevance to alkyl substituted cyclopentanes also present. However, the previous oxidation studies of cyclopentane have primarily focused on neat mixtures. Blending cyclopentane with dimethyl ether in this work therefore serves to inform our understanding of, and improve predictive models for, multi-component mixtures. Here, the auto-ignition of cyclopentane/dimethyl ether blends was studied in a high-pressure shock tube and in a rapid compression machine. A wide range of temperatures (650 – 1350 K) and elevated pressures of 20 and 40 bar were studied at equivalence ratios of 0.5, 1.0 and 2.0 in air for two blending ratios (30/70 and 70/30 mole% cyclopentane/di-methyl ether mixtures). A detailed kinetic model for cyclopentane was revised to capture the measured ignition delay times and apparent heat release rates in this study. Literature ignition delay time, jet-stirred reactor, and laminar burning velocity measurements of neat cyclopentane were used as additional validation. Improvements to the kinetic model were based on recent literature studies related to sub-models including cyclopentene and cyclopentadiene which allowed the removal of previous local rate-constant optimizations. Low temperature reactivity of cyclopentane was found to be controlled by the branching ratio between concerted elimination of HO͘ 2 and the strained formation of Q&#775OOH radicals in agreement with previous studies. In this study, the low branching ratio of Q&#775OOH formation increases the influence of a competing consumption pathway for cyclopentyl-peroxy (CPTO͘ 2 J) radicals. The sensitivity of the simulated ignition delay times to the formation of cyclopentyl hydroperoxide (CPTO 2 H), from CPTO͘ 2 J and HO͘ 2 , is discussed. The current model is used to analyze the influence of dimethyl ether on the reactivity of cyclopentane in the context of previous literature studies of dimethyl ether binary blends with ethanol and toluene.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗