Search NASA⌕ Search

SEARCH · Search NASA

Results for “exhaust diffuser”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Experimental Investigation of a Morphing Nacelle Ducted Fan

The application of Circulation Control to the nacelle of a shrouded fan is proposed as a means to enhance off-design performance of the shrouded fan. Typically, a fixed geometry shroud is efficient at a single operating condition. Modifying circulation about the fixed geometry is proposed as a means to virtually morph the shroud without moving surfaces. This approach will enhance off-design-point performance with minimal complexity, weight, and cost. Termed the Morphing Nacelle, this concept provides an attractive propulsion option for Vertical Take-off and Landing (VTOL) aircraft, such conceptual Personal Air Vehicle (PAV) configurations proposed by NASA. An experimental proof of concept investigation of the Morphing Nacelle is detailed in this paper. A powered model shrouded fan model was constructed with Circulation Control (CC) devices integrated in the inlet and exit of the nacelle. Both CC devices consisted of an annular jet slot directing a jet sheet tangent to a curved surface, generally described as a Coanda surface. The model shroud was tailored for axial flight, with a diffusing inlet, but was operated off-design condition as a static lifting fan. Thrust stand experiments were conducted to determine if the CC devices could effectively improve off-design performance of the shrouded fan. Additional tests were conducted to explore the effectiveness of the CC devices a means to reduce peak static pressure on the ground below a lifting fan. Experimental results showed that off-design static thrust performance of the model was improved when the CC devices were employed under certain conditions. The exhaust CC device alone, while effective in diffusing the fan exhaust and improving weight flow into shroud inlet, tended to diminish performance of the fan with increased CC jet momentum. The inlet CC device was effective at reattaching a normally stalled inlet flow condition, proving an effective means of enhancing performance. A more dramatic improvement in static thrust was obtained when the inlet and exit CC devices were operated in unison, but only over a limited range of CC jet momentum. Operating the nacelle inlet and exit CC devices together proved very effective in reducing peak ground plane static pressure, while maintaining static thrust. The Morphing Nacelle concept proved effective at enhancing off-design performance of the model; however, additional investigation is necessary to generalize the results.

Kondor, Shayne A.↗

Spring 2014 Internship Diffuser Data Analysis

J-2X engine testing on the A-2 test stand at the NASA John C. Stennis Space Center (SSC) has recently concluded. As part of that test campaign, the engine was operated at lower power levels in support of expanding the use of J-2X to other missions. However, the A-2 diffuser was not designed for engine testing at the proposed low power levels. To evaluate the risk of damage to the diffuser, computer simulations were created of the rocket engine exhaust plume inside the 50ft long, water-cooled, altitude-simulating diffuser. The simulations predicted that low power level testing would cause the plume to oscillate in the lower sections of the diffuser. This can possibly cause excessive vibrations, stress, and heat transfer from the plume to the diffuser walls. To understand and assess the performance of the diffuser during low power level engine testing, nine accelerometers and four strain gages were installed around the outer surface of the diffuser. The added instrumentation also allowed for the verification of the rocket exhaust plume computational model. Prior to engine hot-fire testing, a diffuser water-flow test was conducted to verify the proper operation of the newly installed instrumentation. Subsequently, two J-2X engine hot-fire tests were completed. Hot-Fire Test 1 was 11.5 seconds in duration, and accelerometer and strain data verified that the rocket engine plume oscillated in the lower sections of the diffuser. The accelerometers showed very different results dependent upon location. The diffuser consists of four sections, with Section 1 being closest to the engine nozzle and Section 4 being farthest from the engine nozzle. Section 1 accelerometers showed increased amplitudes at startup and shutdown, but low amplitudes while the diffuser was started. Section 3 accelerometers showed the opposite results with near zero G amplitudes prior to and after diffuser start and peak amplitudes to +/- 100G while the diffuser was started. Hot-Fire Test 1 strain gages showed different data dependent on section. Section 1 strains were small, and were in the range of 50 to 150 microstrain, which would result in stresses from 1.45 to 4.35 ksi. The yield stress of the material, A-285 Grade C Steel, is 29.7 ksi. Section 4 strain gages showed much higher values with strains peaking at 1600 microstrain. This strain corresponds to a stress of 46.41 ksi, which is in excess of the yield stress, but below the ultimate stress of 55 to 75 ksi. The decreased accelerations and strain in Section 1, and the increased accelerations and strain in Sections 3 and 4 verified the computer simulation prediction of increased plume oscillations in the lower sections of the diffuser. Hot-Fire Test 2 ran for a duration of 125 seconds. The engine operated at a slightly higher power level than Hot-Fire Test 1 for the initial 35 seconds of the test. After 35 seconds the power level was lowered to Hot-Fire Test 1 levels. The acceleration and strain data for Hot-Fire Test 2 was similar during the initial part of the test. However, just prior to the engine being lowered to the Hot-Fire Test 1 power level, the strain gage data in Section 4 showed a large decrease to strains near zero microstrain from their peak at 1500 microstrain. Future work includes further strain and acceleration data analysis and evaluation.

Laigaie, Robert T.↗

Prediction of engine exhaust concentrations downwind from the Delta-Thor Telsat-A launch of 9 November 1972

Results are presented of the downwind concentrations of engine exhaust by-products from the Delta-Thor Telsat-A vehicle launched from Cape Kennedy, Florida on November 9, 1972 (2014 EST). The meteorological conditions which existed are identified as well as the exhaust cloud rise and the results from the MSFC Multilayer Diffusion Model calculations. These predictions are compared to exhaust cloud sampled data acquired by the Langley Research Center personnel. Values of the surface level concentrations show that very little hydrochloric acid, carbon monoxide, or aluminum oxide reached the ground.

Kaufman, J. W.↗

Relating reconnection rate, exhaust structure and effective resistivity

The magnetic reconnection structure consists of a central diffusion region (CDR) and a cone or wedge shaped reconnection exhaust containing accelerated plasma flows and electromagnetic fluctuations. We predict here the relationship among the exhaust half-cone angle (θ{sub e}), the half width (w) of the CDR, the outflow velocity V{sub o}, and the effective resistivity (η{sub eff}), which includes the effects of all the nonideal terms in the generalized Ohm's law. The effective resistivity is defined as the ratio of reconnection electric field E{sub rec} to the current density J{sub y} at the X point and it essentially represents the loss of momentum from the current-carrying plasma particles due to scattering by waves, their inertia or outflux from the CDR. The relation is checked against relevant results previously reported from laboratory experiments, space observations, and simulations, showing excellent agreement. The relation can be used for estimating the ad-hoc effective resistivity often used in magnetohydrodynamic modeling of reconnection.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Application of a Gaussian multilayer diffusion model to characterize dispersion of vertical HCl column density in rocket exhaust clouds

Solid rocket exhaust cloud dispersion cases, based on seven meteorological regimes for overland advection in the Cape Canaveral, Florida, area, are examined for launch vehicle environmental impacts. They include a space shuttle case and all seven meteorological cases for the Titan 3, which exhausts 60% less HC1. The C(HC1) decays are also compared with recent in cloud peak HC1 data from eight Titan 3 launches. It is stipulated that while good overall agreement provides validation of the model, its limitations are considerable and a dynamics model is needed to handle local convective situations.

Pellett, G. L.↗

Jet diffuser for simulating ram conditions on a turbojet-engine static test stand

A jet diffuser for simulating flight or ram conditions on a turbojet-engine static test stand was designed and investigated. The diffuser utilizes the kinetic energy of the jet from a turbojet engine to reduce the discharge pressure at the exhaust nozzle and thereby provides simulated ram-pressure ratios across the engine. The engine exhaust nozzle discharges into an exhaust chamber (flexibly sealed to the tail pipe), which is connected to a diffuser by a bell-shaped nozzle. The pressure in the exhaust chamber is controlled independently of engine speed by a variable-area shutter at the diffuser discharge. The jet diffuser simulated ram-pressure ratios from 0.95 to 2.2 at various simulated pressure altitudes for a range of engine speeds from 85 to 100 percent of maximum rpm. Agreement of data obtained with and without the jet diffuser for a ram-pressure ratio of 1.0 indicated that the presence of the diffuser did not interfere with the flow through the engine exhaust-nozzle outlet.

Bohanon, H R↗

Magnetospheric Multiscale Mission Observations of the Outer Electron Diffusion Region

This paper presents Magnetospheric Multiscale mission (MMS) observations of the exhaust region in the vicinity of the central reconnection site in Earth's magnetopause current sheet. High-time-resolution measurements of field and particle distributions enable us to explore the fine structure of the diffusion region near the X line. Ions are decoupled from the magnetic field throughout the entire current sheet crossing. Electron jets flow downstream from the X line at speeds greater than the E by B drift velocity. At or around the magnetospheric separatrix, large-amplitude electric fields containing field-aligned components accelerate electrons along the magnetic field toward the X line. Near the neutral sheet, crescent-shaped electron distributions appear coincident with (1) an out-of-plane electric field whose polarity is opposite to that of the reconnection electric field and (2) the energy transfer from bulk kinetic to field energy. The observations indicate that MMS passed through the edge of an elongated electron diffusion region (EDR) or the outer EDR in the exhaust region.

Hwang, K.-J.↗

Time-Resolved PIV Measurements of Flow Field at the Exit of a Diffuser Mounted on a Rotating Detonation Combustor

Time-resolved particle image velocimetry at 30 kHz is applied to the exhaust flow field of a RDC system configured with a diffuser geometry and a converging-diverging (CD) nozzle. The RDC is operated with methane fuel and oxygen-enriched air, motivated by power generation applications. The measured flow-field is discretized into axial and non-axial velocity components. Results are shown to characterize the flow-field across a cord length at the exit plane. Instantaneous contours of the two velocity components, and 1D histograms of velocity components, and 2D histograms of total velocity and tilt angle are shown at multiple locations in the flow. Repeatability of the data is evaluated by comparing tests conducted at similar flow rates. Results are presented for a baseline test case, and test cases showing the effect of reactant higher flow rate and CD nozzle geometry. Finally, the results are compared to a previous RDC study without the diffuser to compare the effectiveness of the diffuser and CD nozzle designs in mitigating the flow periodicity at the combustor exit.

particle image velocimetry, pressure gain combusti↗

Time-Resolved PIV Measurements of Flow Field at Diffuser Exit Downstream of a Rotating Detonation Combustor

Time-resolved particle image velocimetry at 30 kHz is applied to the exhaust flow field of a RDC system configured with a diffuser geometry and a converging-diverging (CD) nozzle. The RDC is operated with methane fuel and oxygen-enriched air, motivated by power generation applications. The measured flow-field is discretized into axial and non-axial velocity components. Results are shown to characterize the flow-field across a cord length at the exit plane. Instantaneous contours of the two velocity components, and 1D histograms of velocity components, and 2D histograms of total velocity and tilt angle are shown at multiple locations in the flow. Repeatability of the data is evaluated by comparing tests conducted at similar flow rates. Results are presented for a baseline test case, and test cases showing the effect of reactant higher flow rate and CD nozzle geometry. Finally, the results are compared to a previous RDC study without the diffuser to compare the effectiveness of the diffuser and CD nozzle designs in mitigating the flow periodicity at the combustor exit.

03 NATURAL GAS↗

A semi-automated algorithm for designing stellarator divertor and limiter plates and application to HSX

We present a semi-automated algorithm for designing three-dimensional divertor or limiter plates targeting low heat loads. The algorithm designs the plates in two stages: firstly, the parallel heat flux distribution is caught on vertically-inclined plates at one or several toroidal locations. Secondly, the power per unit area is reduced by stretching, tilting and bending the plates toroidally. Heat transport is modelled using the EMC3-Lite code, which uses an anisotropic diffusion model. We apply this scheme to HSX, a medium-sized stellarator located at the University of Wisconsin–Madison. Starting from the current machine with an extended vessel wall, we construct plates which are able to effectively catch and spread the heat for three different magnetic configurations. The scheme has a computational cost in the order of tens of CPU-minutes, making it a powerful tool for semi-automated plasma-facing component design in three-dimensional environments.

anisotropic diffusion↗

Exhaust cloud rise and growth for Apollo Saturn engines.

Empirical and analytical results have been reduced from time-lapse photographs of exhaust clouds during the launch of Apollo 10, 14, 15, and 16 from the Kennedy Space Center. Theoretical predictions of the buoyant cloud rise and growth compare very favorably to actual measurements. The mathematical model predicts with engineering accuracy the terminal altitude and size of the clouds. A principal input to MSFC's multilayer diffusion model is top height of the exhaust cloud. It is this characteristic dimension that is the main subject of this report. An interesting occurrence during launch is the formation of bimodal exhaust cloud which is due to the north-south oriented flame trench directly beneath the base of the vehicle. This study has added considerable information on engine exhaust cloud rise and growth which is essential to the study of atmospheric dispersal in time and space.

Susko, M.↗

Currents and Associated Electron Scattering and Bouncing Near the Diffusion Region at Earth's Magnetopause

Based on high-resolution measurements from NASA's Magnetospheric Multlscale mission, we present the dynamics of electrons associated with current systems observed near the diffusion region of magnetic reconnection at Earth's magnetopause. Using pitch angle distributions (PAD) and magnetic curvature analysis, we demonstrate the occurrence of electron scattering in the curved magnetic field of the diffusion region down to energies of 20eV. We show that scattering occurs closer to the current sheet as the electron energy decreases. The scattering of Inflowing electrons, associated with field-aligned electrostatic potentials and Hall currents, produces a new population of scattered electrons with broader PAD which bounce back and forth in the exhaust. Except at the center of the diffusion region the two populations are collocated and appear to behave adiabatically: the inflowing electron PAD focuses inward (toward lower magnetic field), while the bouncing population PAD gradually peaks at 90 degrees away from the center (where it mirrors owing to higher magnetic field and probable field-aligned potentials).

Lavraud, B.↗

Faster Form of Electron Magnetic Reconnection with a Finite Length X-Line

Observations in Earth’s turbulent magnetosheath downstream of a quasiparallel bow shock reveal a prevalence of electron-scale current sheets favorable for electron-only reconnection where ions are not coupled to the reconnecting magnetic fields. In small-scale turbulence, magnetic structures associated with intense current sheets are limited in all dimensions. And since the coupling of ions are constrained by a minimum length scale, the dynamics of electron reconnection is likely to be 3D. Here, both 2D and 3D kinetic particle-in-cell simulations are used to investigate electron-only reconnection, focusing on the reconnection rate and associated electron flows. A new form of 3D electron-only reconnection spontaneously develops where the magnetic X-line is localized in the out-of-plane (z) direction. The consequence is an enhancement of the reconnection rate compared with two dimensions, which results from differential mass flux out of the diffusion region along z, enabling a faster inflow velocity and thus a larger reconnection rate. This outflow along z is due to the magnetic tension force in z just as the conventional exhaust tension force, allowing particles to leave the diffusion region efficiently along z unlike the 2D configuration.

79 ASTRONOMY AND ASTROPHYSICS↗

System and method for removing water and hydrogen from anode exhaust

A fuel cell system includes an anode configured to output an anode exhaust stream comprising hydrogen, carbon dioxide, and water; and a membrane dryer configured to receive the anode exhaust stream, remove water from the anode exhaust stream, and output a membrane dryer outlet stream. The membrane dryer includes a first chamber configured to receive the anode exhaust stream; a second chamber configured to receive a purge gas; and a semi-permeable membrane separating the first chamber and the second chamber. The semi-permeable membrane is configured to allow water to diffuse therethrough, thereby removing water from the anode exhaust stream. The membrane dryer may further be configured to remove hydrogen from the anode exhaust stream.

Jolly, Stephen↗

Single stage, low noise, advanced technology fan. Volume 1: Aerodynamic design

The aerodynamic design for a half-scale fan vehicle, which would have application on an advanced transport aircraft, is described. The single stage advanced technology fan was designed to a pressure ratio of 1.8 at a tip speed of 503 m/sec 11,650 ft/sec). The fan and booster components are designed in a scale model flow size convenient for testing with existing facility and vehicle hardware. The design corrected flow per unit annulus area at the fan face is 215 kg/sec sq m (44.0 lb m/sec sq ft) with a hub-tip ratio of 0.38 at the leading edge of the fan rotor. This results in an inlet corrected airflow of 117.9 kg/sec (259.9 lb m/sec) for the selected rotor tip diameter if 90.37 cm (35.58 in.). The variable geometry inlet is designed utilizing a combination of high throat Mach number and acoustic treatment in the inlet diffuser for noise suppression (hybrid inlet). A variable fan exhaust nozzle was assumed in conjunction with the variable inlet throat area to limit the required area change of the inlet throat at approach and hence limit the overall diffusion and inlet length. The fan exit duct design was primarily influenced by acoustic requirements, including length of suppressor wall treatment; length, thickness and position on a duct splitter for additional suppressor treatment; and duct surface Mach numbers.

Sullivan, T. J.↗

Initial Criticality Assessments to Guide FMEAs on Rocket Engine Hot Fire Testing

Presented is an explanation of the use of the Initial Criticality Assessment (ICA) technique, a triage process for prioritizing required Failure Modes and Effects Analysis (FMEAs), for the European Service Module's main propulsion system's hot-fire test bed at White Sands New Mexico. Rather than instinctively performing many FMEAs of subsystems, or one large system level FMEA where every subcomponent is analyzed, the ICA guided an informed analysis of only the hardware that had a large impact to hazards. The low criticality hardware was documented via the ICA and no FMEA was performed; the work could then focus on the high criticality hardware. Thus a savings of Program resources was achieved. The experiences gained in creating these ICAs for this international collaborative project confirmed that the need for continuous communication across the technical teams is one of the greatest areas of emphasis. The European Space Agency (ESA) is developing the European Service Module (ESM), with its primary contractor, Airbus Defence and Space in Germany, for delivery to the National Aeronautics and Space Administration (NASA). The module will be equipped with a total of 21 engines to support NASA’s Orion spacecraft: one U.S. Space Shuttle Orbital Maneuvering System-Engine (OMS-E), eight auxiliary thrusters and 12 smaller RCS (Reaction Control System) thrusters. The main ESM propulsion system, used for large translational maneuvers, consists of one OMS-E... To qualify the design of the ESM propulsion subsystem (PSS) an all-steel Propulsion Qualification Module (PQM) structure is used to test the propulsion systems on Orion, including “hot firing” of the OMS engine, thrusters, and RCS. The PQM has been developed as a hot-fire test bed to be tested at the NASA White Sands Test Facility (WSTF). One of the objectives of the testing is to assure that the OMS-E can be safely operated with the PQM. Testing will also demonstrate that the PQM can set the proper upstream pressures and temperatures for the OMS-E to operate nominally given the PQM has never been tested in hot-fire operation with OMS-E before. In order to safely conduct the test campaign, hardware such as the engine subassembly, fluid feed lines, valves, electrical power lines, instrumentation, stiff links, installation Ground Support Equipment (GSE), and diffuser [whose objectives are to collect the exhaust of the OMS-E to actively cool down the exhaust gases, reduce thermal exchanges, and create a vacuum at OMS-E level before igniting], had to be analyzed for any hazards and failure modes.

Fault Tolerance↗