SEARCH · Search NASA
Results for “experimental investigation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Experimental Investigation of Polymer Induced Fouling of Heater Tubes in the First-Ever Polymer Flood Pilot on Alaska North Slope
Mineral fouling in heat exchangers has been extensively investigated by researchers in recent times. The oil and gas industry has a long history of fouling issues in production systems as a result of produced fluids treatment. Due to decline in production rates in oilfields new technologies are being developed and field tested in pilots. Polymer flooding is one such technology that involves addition of polymers to injection fluids to enhance oil production. A polymer flood pilot has been set up in the Schrader Bluff viscous oil reservoir at Milne Point field on the Alaska North Slope (ANS). The results from the pilot are encouraging, however a major concern of the operator is the influence of polymer on the production system after breakthrough, especially the fouling in heat exchangers. This study investigates the propensity of polymer fouling on the heater tubes as a function of different variables, with the ultimate goal of determining safe and efficient operating conditions. This work applies a multi-experimental approach to study the severity of polymer-induced fouling in both dynamic and static states of produced fluids as well as studying the stability of polymer solutions at different temperatures. A unique experimental setup was designed and developed in-house to simulate the fouling process on the heating tube. The influence of heating tube skin temperature, tube material, and polymer concentration on fouling tendency was investigated. Each test was run five times with the same tube, and in each run, the freshly prepared synthetic brine and polymer solution was heated from 77°F to 122°F to mimic field-operating conditions. The heating time and fouling amount were recorded for each run. Dynamic Scale Loop (DSL) tests were conducted to study fouling due to polymer at different temperatures (165°F to 350°F) in a dynamic state of fluid flow where the fluids mimic the residence time of fluids in the heat exchanger on the field pilot. Cloud point measurement has also been conducted to find the critical temperature at which the polymer in solution becomes unstable and precipitates out. The morphology and composition of the deposit samples were analyzed by environmental scanning electron microscopy (ESEM) and X-ray diffraction (XRD), respectively. It was found that the presence of polymer in produced fluids would aggravate the fouling issues on both carbon steel and stainless-steel surfaces at all tested skin temperatures. Only higher skin temperatures of 250°F and 350°F could cause polymer-induced fouling issues on the copper tube surface, and the fouling tendency increased with polymer concentration. At the lower skin temperatures of 165°F, no polymer-induced fouling was identified on the copper tube. A critical temperature that is related to the cloud point of the polymer solution was believed to exist, below which polymer-induced fouling would not occur, and only mineral scale was deposited but above which the polymer would aggravate the fouling issue. The cloud point of the tested polymer solution was determined to be between 220°F and 230°F. In the DSL tests it was found that at higher skin temperatures of 250°F and 350°F tube blocking was observed in the DSL tests whereas the tests at 165°F and 200°F did not show any tube blocking in the same time period. These experiments also manifested the influence of cloud point of the solution as deposit rate increased significantly in both carbon steel and stainless-steel tubes when the skin temperature was higher than the solution cloud point. The results of this study have provided guidance to the operator for the field-operations.
Modeling and Experimental Investigation of Spent Fuel Disposal in Crystalline Rocks: FY23 Progress Report
The objective of the crystalline disposal work packages is to advance our understanding of long-term disposal of used fuel in crystalline rocks and to develop necessary experimental and computational capabilities to evaluate various disposal concepts in such media.
Computational and Experimental Investigation of Discrete “W” Turbulators for sCO2 Turbine Internal Cooling
Direct-fired supercritical CO2 (sCO2 ) cycles are of particular interest for power generation due to the potential for higher thermal efficiencies with inherent CO2 capture. Direct fired sCO2 turbines must withstand high temperatures and the density of the working fluid is much higher than conventional Brayton cycles. Based on conventional Brayton cycle applications, internal serpentine cooling channels with ribbed turbulator strips are a common approach to achieve the required cooling, while minimizing coolant utilization. Most of the previous studies of coolant channel heat transfer enhancements have focused on serpentine channels using air as the cooling media at Reynold’s numbers typical of Brayton cycles. This paper investigates the Nusselt number augmentation of coolant channels with no features, ribbed turbulators, and discrete “W” turbulators with surface roughness effects included and CO2 as the coolant. The numerical results are compared to experimental results using CO2 as the cooling media at Reynold’s numbers ranging from 100,000 to 300,000. The results show the Nusselt number augmentation plateaus with increasing Reynolds number, in contrast to the decay observed in prior publications with air as the coolant media. Additionally, the CFD results indicate the discrete “W” geometry provides a 10% increase in Nusselt number augmentation relative to the angled ribbed turbulators.
Experimental investigation of Multi-Mode heat transfer to a Free-Falling dilute particle cloud in a heated vertical tube
The development of dilute particle heat exchangers and reactors for advanced energy systems requires an understanding of the multi-mode heat transfer from a heated wall to falling particles. This study presents experimental results of the overall heat transfer coefficient for a free-falling, dilute flow of particles with solid volume fraction from 0.0005 to 0.006 corresponding to feed rates from 3.7 kg s -1 m -2 to 44 kg s -1 m -2 in a vertical, heated tube containing quiescent air at atmospheric pressure. Tube wall temperatures are varied between 300°C to 900°C while keeping the particle inlet temperature constant. The experimental results show that the overall heat transfer coefficient is a strong function of particle feed rate and surface temperature. Good agreement was obtained with prior studies conducted at comparable temperatures but lower particle feed rates (< 4 kg m -2 s -1 ). The established correlations for particle-to-wall radiation and particle-to-gas convection were used to estimate the wall-to-gas convective contribution from the measured overall heat transfer coefficient. The experimental results indicated a 4 to 6 times improvement in the wall convection in the solid-gas mixture compared to that expected from natural convection in a single-phase gas. Furthermore, the data presented here are applicable to characterize heat transfer in dilute particle heat exchangers, furnaces, and solar receivers.
Experimental investigation of unsteady flow dynamics in therminol-66 using edge tone-induced oscillations
Recent research has demonstrated that flow oscillations induced by a wedge positioned opposite the jet outlet in edge tones can be effectively utilized for flow measurement purposes. This highlights the necessity for developing advanced instrumentation capable of precise flow measurements in experimental setups exposed to radiation and in challenging fluids such as molten salts. Here, this study contributes to the existing body of knowledge by conducting experiments using Therminol-66, an effective surrogate for FLiBe under appropriate temperature conditions for nuclear applications, across a broad range of Reynolds numbers from 17,700 to 555,000. Experiments were conducted with Therminol-66 at approximately 368.8 K under atmospheric pressure, with varying flow rates. A reliable correlation was established between the generated frequencies, corresponding flow rates, and device geometry parameters. The data were subjected to non-dimensional analysis to reveal the interrelationships among flow rate, fluid properties, device geometry, and their impact on the acoustic tones produced by the edge tone device. These findings contribute to the development of precise flow measurement instrumentation for use in challenging environments.
Experimental Investigation of Cavitation-Induced Erosion Using X-Ray Imaging and Tomography
High injection pressure in diesel engines can lead to cavitation-induced erosion in injector nozzles. One important factor affecting the severity of erosion is the fuel and its properties. Traditionally, modeling and simulation studies have used single-component representations of fuels, but realistic fuels feature a multitude of components and can even include volatile additives such as water and alcohol. To provide realistic benchmarks and comparisons, experimental measurements quantifying erosion characteristics were made using ultra-low sulfur diesel (ULSD) and two alternative diesel fuels (ADF). X-ray imaging and computed tomography were used to investigate cavitation-induced erosion onset and progression. Hard X-ray tomography revealed injector internal geometry, including details such as surface marks from the manufacturing process and erosion patterns from repeated injections. Erosion progression was measured using X-ray tomography and imaging performed between injections. The critical erosion site was found to be similar across different fuel blends, while the erosion rate and incubation time were sensitive to the fuel blend. The injector geometry and the erosion characteristics were also prepared for numerical model development and validation.
Experimental Investigation of Hydraulic Fracturing and Stress Sensitivity of Fracture Permeability Under Changing Polyaxial Stress Conditions
Understanding and predicting fracture propagation and subsequent fluid flow characteristics is critical to geoenergy technologies that engineer and/or utilize favorable geological conditions to store or extract fluids from the subsurface. Fracture permeability decreases nonlinearly with increasing normal stress, but the relationship between shear displacement and fracture permeability is less well understood. We utilize the new Geo–Reservoir Experimental Analogue Technology (GREAT cell), which can apply polyaxial stress states and realistic reservoir temperatures and pressures to cylindrical samples and has the unique capability to alter both the magnitude and orientation of the radial stress field by increments of 11.25° during an experiment. We load synthetic analogue materials and real rock samples to stress conditions representative of 500–1,000 m depth, investigate the hydraulic stimulation process, and then conduct flow experiments while changing the fluid pressure and the orientation of the intermediate and minimum principal stresses. High–resolution circumferential strain measurements combined with fluid pressure data indicate fracture propagation can be both stable (no fluid pressure drop) and unstable (fluid pressure drop). The induced fractures exhibit both opening and shear displacements during their creation and/or during fluid flow with changing radial stress states. Flow tests during radial stress field rotation reveal that fracture normal effective stress has first–order control on fracture permeability but increasing fracture offset can lead to elevated permeabilities at maximum shear stress. Here, the results have implications for our conceptual understanding of fracture propagation as well as fluid flow and deformation around fractures.
Methane foam performance evaluation in water-wet unconsolidated porous media: A systematic experimental investigation at elevated pressure and temperature conditions
In the petroleum industry, enhanced oil recovery (EOR) techniques employ foam extensively to establish conformance control in heterogeneous and fractured reservoirs in order to increase the sweep efficiency. In such applications, foam performance evaluation under complex subsurface conditions is pivotal for the effective and optimized deployment of foam treatment. However, there is a scarcity of hydrocarbon gas foam generation and evaluation studies that examine the relationships between foam performance and the critical foam parameters at high-pressure and high-temperature conditions. Here, this study aims at methodically investigating the effects of several foam parameters on methane foam performance in water-wet proppant packs under harsh operating conditions. This is in relation to the technical needs of hydrocarbon foam injection into hydraulically-induced, propped fractures in unconventional oil reservoirs. To this end, a state-of-the-art experimental foam generation apparatus was designed, fabricated, and commissioned. We performed a large number of foam flow experiments on proppant packs using methane gas and different foaming agents at 3500 psi and 115°C. Anionic and amphoteric surfactants were employed to probe the effect of their ionic nature on foam performance. Foam performance sensitivities to various foam generation parameters and operating conditions, such as surfactant concentration, gas fraction, total injection rate, operating pressure, salinity, and proppant pack length were investigated. To this end, steady-state pressure drops across the proppant packs during foam generation and foam's apparent viscosity were measured to quantify the foam performance of surfactants. The results were then analyzed to determine optimum values of the foam parameters and the interplay between these parameters are discussed here. The systematic results achieved from this work are in agreement with the trends available in the literature and provide new insights into complexities of in situ foam generation in water-wet, unconsolidated porous media at extreme reservoir conditions.
Solvent-Mediated Control of Nanocellulose Dispersion: An Integrated Computational and Experimental Investigation
Fibrillated cellulose derived from forestry feedstocks represents a renewable and high-strength materials platform for circular bioeconomies. However, its practical implementation is hindered by the irreversible aggregation of nanocellulose architectures, including cellulose nanofibers (CNFs). Solvent-based dispersion offers a simple and practical route to prevent CNF aggregation. Here, in this work, we integrate classical and enhanced sampling molecular dynamics (MD) simulations with experimental suspension rheology and atomic force microscopy (AFM) to elucidate how solvent environments tune CNF–CNF interactions and dispersion stability. CNF–CNF contact free energies computed from MD simulations reveal reduced aggregation in acetone/water, γ-valerolactone (GVL)/water, and tetrahydrofuran (THF)/water and pure acetone compared with pure water, reflecting stronger CNF-solvent relative to inter-CNF interactions. Correspondingly, CNF-solvent suspensions in these solvent systems exhibit stronger inter-fibril network structures and enhanced recovery compared to water, indicating improved CNF-solvent affinity. Liquid cell AFM imaging in acetone–water mixtures and in pure acetone further confirm the presence of well-dispersed CNFs. By combining multiscale computation with targeted experiments, this study establishes a rational framework for solvent design to achieve stable nanocellulose dispersions for high-strength biobased materials and efficient bioenergy conversion.
Numerical and Experimental Investigation of Nanostructure-Based Asymmetric Light Transmission Interfaces for Solar Concentrator Applications
Research in asymmetric light transmission interfaces has been recently gaining traction. While traditionally considered for optical circuitry applications, there is a new interest to use these interfaces in luminescent solar concentrators. Previous studies have shown that applying them to the top surface of a concentrator could mitigate surface losses. This paper presents experimental results for proof-of-concept asymmetric light transmission interfaces that may have potential applications in luminescent solar concentrators. The interfaces and the underneath substrate were created in a single step from polydimethylsiloxane using silicon molds fabricated on <100> wafers via anisotropic wet etching. The resulting structures were pyramidal in shape. Large surface areas of nanostructures repeating at 800 nm, 900 nm, and 1000 nm were tested for backward and forward transmission using a spectrometer. Results showed a 21%, 10%, and 0% average transmissivity difference between the forward and backward directions for each periodicity, respectively. The trends seen experimentally were confirmed numerically via COMSOL simulations.
Ab initio modeling and experimental investigation of Fe 2 P by DFT and spin spectroscopies
Fe 2 P alloys have been identified as promising candidates for magnetic refrigeration at room-temperature and for custom magnetostatic applications. The intent of this study is to accurately characterize the magnetic ground state of the parent compound, Fe 2 P, with two spectroscopic techniques, μSR and NMR, in order to provide solid bases for further experimental analysis of Fe 2 P-type transition metal based alloys. Herein, we perform zero applied field measurements using both techniques below the ferromagnetic transition T C = 220 K. The experimental results are reproduced and interpreted using first principles simulations, validating this approach for quantitative estimates in alloys of interest for technological applications.
Experimental Investigation of Fuel Staging Effect on Modal Dynamics of Thermoacoustic Azimuthal Instabilities in a Multi-Nozzle Can Combustor
Abstract This paper analyzes the dynamics of unstable azimuthal thermoacoustic modes in a lean premixed combustor. Azimuthal modes can be decomposed into two counter rotating waves where they can either compete and potentially suppress one of them (spinning) or coexist (standing), depending on the operating conditions. This paper describes experimental results of the dynamical behaviors of these two waves. The experimental data were taken at different mass flow rates as well as different azimuthal fuel staging in a multi-nozzle can combustor. It is shown that at a low flow rate with uniform fuel distribution, the two waves have similar amplitudes, giving rise to a standing wave. However, the two amplitudes are slowly oscillating out of phase to each other, and the phase difference between the two waves also shows oscillatory behavior. For an intermediate flow rate, the dynamics show intermittency between standing and spinning waves, indicating that the system is bistable. In addition, the phase difference dramatically shifts when the mode switches between standing and spinning waves. For a high flow rate, the system stabilizes at a spinning wave most of the time. These experimental observations demonstrate that not only the amplitudes of two waves but also the phase difference plays an important role in the dynamics of azimuthal mode. For non-uniform azimuthal fuel staging, the modal dynamics exhibit only an oscillatory standing wave behavior regardless of the mass flow rate. Compared to the uniform fuel staging, however, the pressure magnitude is considerably reduced, which provides a potential strategy to mitigate and/or suppress the instabilities.
Experimental investigation of surface roughness/wettability pattern effect on crystallization fouling over falling-film flow
In many industries, including desalination, scaling in heat exchangers is a persistent issue, and most methods of scaling control involve environmentally hazardous chemical additives. Exploiting the effects of surface features and flow-imposed shear on salt deposition might introduce a new approach to scale management, opening the possibility of self-cleaning surfaces. In this work, we experimentally explore surface roughness and wettability patterns interaction with salt deposition and flow shear. Heat transfer and scale mass deposition on flat surfaces are measured during thin-film evaporation of calcium sulfate solution. A wide range of surface roughness (0.027–2.66 μm) is studied at fixed flow and heat flux conditions. Due to improved mixing, heat transfer is enhanced with rougher surfaces initially; however, degrades more quickly than smoother surfaces. Following a period of initial mass deposition fluctuation, a steady scaling stage is observed, with rough surfaces scaling more than smooth surfaces. Wettability patterned surfaces can suppress crystal nucleation without sacrificing overall surface wetting, resulting in antifouling performance and heat transfer enhancement. Scale mass deposition on a patterned surface is reduced by 60 %, and 27 % heat transfer improvement over the baseline surface is found. Furthermore, this study provides guidance to surface manipulation for heat transfer improvement and fouling mitigation.
Combined First-Principles and Experimental Investigation into the Reactivity of Codeposited Chromium–Carbon under Pressure
High-pressure synthesis in the diamond anvil cell suffers from the lack of a general approach for the control of precursor stoichiometry and homogeneity. Here, we present results from a new method we have developed that uses magnetron cosputtering to prepare stoichiometrically precise and atomically mixed amorphous films of Cr:C. Laser-heated diamond anvil cell experiments carried out on a flake of this sample at pressures between 13.5 and 24.3 GPa lead to the observation of Cr 3 C (Pnma) over the entire pressure range–in good agreement with our in-house theoretical predictions–but also reveal two other metastable phases that were not expected: a novel monoclinic chromium carbide phase and the NaCl-type CrC (Fm3̅m) phase. The unexpected stability of CrC is investigated by using first-principles methods, revealing a large stabilizing effect tied to substoichiometry at the carbon site. These results offer an important case study into the current limitations of crystal structure prediction methods with regard to phase complexity and bolster the growing need for advanced theoretical approaches that can more completely survey experimentally unexplored phase space.
Experimental investigation on phase change material–based finned tube heat exchanger for thermal energy storage and building envelope thermal management
Phase change materials (PCMs) are attractive solutions for thermal energy storage (TES) applications by absorbing and releasing large amounts of latent heat during solid–liquid phase transitions. However, their relatively low thermal conductivity requires novel heat exchanger–based solutions to improve the power density and overall energy storage efficiency of the TES system. This work presents the design and experimental results of a finned tube heat exchanger to store collected natural thermal energy from a building envelope in a latent-based TES and to release it later for building heating/cooling applications. We experimentally evaluate the finned tube heat exchanger and evaluate the performance of TES in reducing building heating and cooling loads over 3–4 h of desired time of operation (e.g., peak load). The optimized design allows for maximum energy density by minimizing the heat exchanger volume, and the system is evaluated experimentally using commercially available heat exchanger materials and an organic PCM. Here, the experimental results reveal that the TES system is able to charge and discharge stored latent energy within 3–4 h, matching peak building electricity demand duration under an average fluid flow rate of 0.136 kg/s and temperature difference of 5.55 °C. Importantly, such optimized designs illuminate a path toward TES designs that are low-cost, scalable, and optimized for thermal energy and power availability under the desired time of operation.
Experimental investigation of multi-scale strain-field heterogeneity in rocks
Rocks have inherently heterogeneous micro-structures. The mechanical response of these heterogeneous micro-structures primarily governs the overall macroscopic behavior of intact rocks, as these features cause heterogeneity in the distribution of stress and strain within a rock volume. These attributes have generally been studied through numerical tools, but in this study, the stress-induced multi-scale spatial heterogeneity in the strain-field of three types of rocks was analyzed experimentally. The full-field non-contact strain measurement approach of 2D Digital Image Correlation (DIC) was employed for real-time evaluation of the progression of strain-field heterogeneity across the surface of the rock specimens when subjected to uniaxial compression. The results show that the strain-field heterogeneity is a characteristic of the inherent heterogeneity of the rock specimens, and that it amplifies with the magnitude of stress applied on the rock specimens. The changes in the strain-field heterogeneity with loading were consistent with established microcrack evolution processes in the rock specimens. The statistical fluctuation in the strain-field heterogeneity of the three rocks at varying gauge lengths (GL) was then analyzed for the determination of the Representative Volume Element (RVE) length-scale at increasing load levels. The evolution of the RVE length-scale with loading facilitates an objective way of determination of the stress at which the strain-field heterogeneity increases and begins to influence the overall global response of the material. The RVE length-scale variation with loading showed that at the RVE length-scale reaches the specimen-scale at load levels well below the peak strength.
“Experimental investigation of the governing parameters of atmospheric ice nucleation using field-collected and laboratory generated aerosol particles and its application in cloud resolving models” (Final Report)
The objective of this research project is to improve our understanding of the role of aerosol particles acting as ice-nucleating particles (INPs) which in turn define the mixed-phase and cirrus cloud radiative properties and thus climate. The focus is placed on how the physicochemical particle population properties determine the particles’ ability to initiate ice nucleation. This research project combined micro-spectroscopic particle analysis, experimental ice nucleation studies, and model sensitivity studies to advance our predictive capability of the formation of mixed-phase and cirrus clouds. These project activities have led to new ice nucleation data from laboratory generated and ambient (authentic) aerosol particles furthering process-level understanding, insights in the role of organic aerosol in ice formation, and advancements in the interpretation and parameterization of ice nucleation.