Search NASA⌕ Search

SEARCH · Search NASA

Results for “flat models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Overview of Mars Sample Return – Earth Entry System Woven Roughness Heating Augmentation Test in NASA Langley’s Mach 6 Wind Tunnel

The Mars Sample Return Mission (MSR) is a planned NASA flagship mission in which a sample retrieval lander (SRL) with a rover will be flown to Mars to obtain sample tubes on the surface that were dropped by the Mars 2020 rover [1]. After obtaining the sam-ples, the rover will return and ascend back to Martian orbit onboard the Mars Ascent Vehicle (MAV). Upon return to Earth orbit, the samples will perform Entry, Descent, and Landing (EDL) with the Earth Entry Sys-tem (EES) architecture, and land in Utah. The EES vehicle will utilize a HEEET-variant as its TPS, which will be the first time a woven TPS will be used on a flagship NASA mission [2]. This TPS offers a unique challenge for Computational Fluid Dynamics (CFD) modeling of the aerothermal envi-ronment of the vehicle, as woven roughness heating augmentation has not been extensively investigated experimentally. As a result, in order to validate com-putational models for woven roughness heating aug-mentation, a wind tunnel test campaign at NASA Langley Research Center’s Mach 6 wind tunnel was performed in April of 2023. This test campaign consisted of over a hundred runs with Reynolds numbers spanning from 1-7 mil-lion 1/ft and with six separate wind tunnel models used. A second campaign with a suite of new models will be conducted in Summer 2023 as well as a cam-paign with a flat plate model, both of which are of great interest to the MSR-EES project. The data obtained from this test are extremely vital for the MSR mission, as they will validate CFD roughness heating models which will be directly used to design the TPS of the EES portion of MSR and characterize the heating environment that the entry ve-hicle will experience. Further extensions of the MSR-EES test campaign will continue to provide validation data for developing more effective computational tools.

Jonathan Cheatwood↗
NASA NTRS1995

Comparisons of the Maxwell and CLL gas/surface interaction models using DSMC

The behavior of two different models of gas-surface interactions is studied using the Direct Simulation Monte Carlo (DSMC) method. The DSMC calculations examine differences in predictions of aerodynamic forces and heat transfer between the Maxwell and the Cercignani-Lampis-Lord (CLL) models for flat plate configurations at freestream conditions corresponding to a 140 km orbit around Venus. The size of the flat plate represents one of the solar panels on the Magellan spacecraft, and the freestream conditions correspond to those experienced during aerobraking maneuvers. Results are presented for both a single flat plate and a two-plate configuration as a function of angle of attack and gas-surface accommodation coefficients. The two-plate system is not representative of the Magellan geometry but is studied to explore possible experiments that might be used to differentiate between the two gas-surface interaction models. The Maxwell and CLL models produce qualitatively similar results for the aerodynamic forces and heat transfer on a single flat plate. However, the flow fields produced with the two models are qualitatively different for both the single-plate and two-plate calculations. These differences in the flowfield lead to predictions of the angle of attack for maximum heat transfer in a two plate configuration that are distinctly different for the two gas-surface interactions models.

Hedahl, Marc O.↗
NASA NTRS1981

Evacuation-induced pressure differentials in multilayer insulation systems

The pressure differentials induced across three types of multilayer insulation systems during evacuation have been measured and compared with values predicted using an idealized parallel plate geometric model. The systems tested were double-aluminized Mylar with a Tissuglas or silk net spacer and crinkled single-aluminized Mylar. Test samples were circular. The influence of purge gas type, layer density, sample diameter, and temperature was systematically investigated. The experimental approach was to measure the absolute pressure history and corresponding pressure differential induced across the insulation during evacuation. The measured pressure differentials were nondimensionalized and compared with those predicted by the parallel plate model as a function of Knudsen number. It was concluded that the parallel plate model is adequate for making engineering analyses. The influence of all parameters, except layer density, is well represented by the model. Representation of the influence of layer density is less satisfactory, but can be improved by modification of the flat plate model to allow for the more obvious practical nonidealities, such as crinkling, or the presence of a net spacer.

Glassford, A. P. M.↗
NASA NTRS2004

A Parametric Study of Jet Interactions with Rarefied Flow

Three-dimensional computational techniques, in particular the uncoupled CFD-DSMC of the present study, are available to be applied to problems such as jet interactions with variable density regions ranging from a continuum jet to a rarefied free stream. When the value of the jet to free stream momentum flux ratio approximately greater than 2000 for a sharp leading edge flat plate forward separation vortices induced by the jet interaction are present near the surface. Also as the free stream number density n (infinity) decreases, the extent and magnitude of normalized pressure increases and moves upstream of the nozzle exit. Thus for the flat plate model the effect of decreasing n (infinity) is to change the sign of the moment caused by the jet interaction on the flat plate surface.

Glass, C. E.↗
NASA NTRS2005

Detached Eddy Simulation of Film Cooling over a GE Flat Plate

The detached eddy simulation of film cooling has been utilized for a proprietary GE plate-pipe configuration. The blowing ratio was 2.02, the velocity ratio was 1.26, and the temperature ratio was 1.61. Results indicate that the mixing processes downstream of the hole are highly anisotropic. DES solution shows its ability to depict the dynamic nature of the flow and capture the asymmetry present in temperature and velocity distributions. Further, comparison between experimental and DES time-averaged effectiveness is satisfactory. Numerical values of span-averaged effectiveness show better prediction of the experimental values at downstream locations than a steady state Glenn HT solution. While the DES method shows obvious promise, there are several issues that need further investigation. Despite an accurate prediction in the hole vicinity, the simulation still falls short in the region x = 10d to 100d. This should be investigated. Also the model used flat plate. Actual turbine blade should be modeled in the future if additional finding is available.

Roy, Subrata↗
NASA NTRS1987

Experimental cavity pressure distributions at supersonic speeds

An investigation was conducted to define pressure distributions for rectangular cavities over a range of free-stream Mach numbers and cavity dimensions. These pressure distributions together with schlieren photographs are used to define the critical values of cavity length-to-depth ratio that separate open type cavity flows from closed type cavity flows. For closed type cavity flow, the shear layer expands over the cavity leading edge and impinges on the cavity floor, whereas for open type cavity flow, the shear layer bridges the cavity. The tests were conducted by using a flat-plate model permitting the cavity length to be remotely varied from 0.5 to 12 in. Cavity depths and widths were varied from 0.5 to 2.5 in. The flat-plate boundary layer approaching the cavity was turbulent and had a thickness of approximately 0.2 in. at the cavity front face for the range of test Mach numbers from 1.5 to 2.86. Presented are a discussion of the results and a complete tabulation of the experimental data.

Stallings, Robert L., Jr.↗
NASA NTRS1976

Flight with lift modulation inside a planetary atmosphere

A set of dimensionless variables (modified Chapman's variables) is introduced in a derivation of general equations for lifting flight and bank modulation within a planetary atmosphere. The atmosphere is assumed spherical and at rest, and a generalized lift-drag polar is also introduced. Corresponding equations for flight over a flat planet model are attained via a straightforward transformation. Two planar flight cases: flight at constant absolute speed over a spherical planet, and flight at constant descent rate over a flat planet, are analyzed, and the required lift control law (with negative or positive lift) is exhibited in each case. Glide at very high descent rate and plane flows of trajectories are analyzed.

Vinh, N. X.↗
NASA NTRS1994

Strong gravitational lensing statistics as a test of cosmogonic scenarios

Gravitational lensing statistics can provide a direct and powerful test of cosmic structure formation theories. Since lensing tests, directly, the magnitude of the nonlinear mass density fluctuations on lines of sight to distant objects, no issues of 'bias' (of mass fluctuations with respect to galaxy density fluctuations) exist here, although lensing observations provide their own ambiguities of interpretation. We develop numerical techniques for generating model density distributions with the very large spatial dynamic range required by lensing considerations and for identifying regions of the simulations capable of multiple image lensing in a conservative and computationally efficient way that should be accurate for splittings significantly larger than 3 seconds. Applying these techniques to existing standard Cold dark matter (CDM) (Omega = 1) and Primeval Baryon Isocurvature (PBI) (Omega = 0.2) simulations (normalized to the Cosmic Background Explorer Satellite (COBE) amplitude), we find that the CDM model predicts large splitting (greater than 8 seconds) lensing events roughly an order-of-magnitude more frequently than the PBI model. Under the reasonable but idealized assumption that lensing structrues can be modeled as singular isothermal spheres (SIS), the predictions can be directly compared to observations of lensing events in quasar samples. Several large splitting (Delta Theta is greater than 8 seconds) cases are predicted in the standard CDM model (the exact number being dependent on the treatment of amplification bias), whereas none is observed. In a formal sense, the comparison excludes the CDM model at high confidence (essentially for the same reason that CDM predicts excessive small-scale cosmic velocity dispersions.) A very rough assessment of low-density but flat CDM model (Omega = 0.3, Lambda/3H(sup 2 sub 0) = 0.7) indicates a far lower and probably acceptable level of lensing. The PBI model is consistent with, but not strongly tested by, the available lensing data, and other open models would presumably do as well as PBI. These preliminary conclusions and the assumptions on which they are based can be tested and the analysis can be applied to other cosmogonic models by straightforward extension of the work presented here.

Cen, Renyue↗
NASA NTRS1992

Modeling radiation forces acting on satellites for precision orbit determination

Models of the TOPEX/Poseidon spacecraft are developed by means of finite-element analyses for use in generating acceleration histories for various orbit orientations which account for nonconservative radiation forces. The acceleration profiles are developed with an analysis based on the use of the 'box-wing' model in which the satellite is modeled as a combination of flat plates. The models account for the effects of solar, earth-albedo, earth-IR, and spacecraft-thermal radiation. The finite-element analysis gives the total force and induced accelerations acting on the satellite. The plate types used in the analysis have parameters that can be adjusted to optimize model performance according to the micromodel analysis and tracking observations. Acceleration related to solar radiation pressure is modeled effectively, and the techniques are shown to be useful for the precise orbit determinations required for spacecraft such as the TOPEX/Poseidon.

Marshall, J. A.↗
NASA NTRS1995

Ames Research Center Mars/Pathfinder Heat Shield Design Verification ARC-JET Test

Design verification tests were performed on samples representing the aerobrake of the Mars/Pathfinder vehicle. The test specimens consisted of the SLA-561V ablator bonded to the honeycomb structure. The primary objective was to evaluate the ablation materials performance and to measure temperatures within the ablator, at the structural bondline and at the back sheet of the honeycomb structure. Other objectives were to evaluate the effect of ablative repair plug material treatment and voids in the heat shield. A total of 29 models were provided for testing in the Ames 60MW arc-jet facility. Of these, 23 models were flat-faced and six remaining models were curved edge ones, intended to simulate the conditions on the curved rim of the forebody where the maximum shear occurred. Eight sets of test conditions were used. The stagnation point heating rates varied from 47 to 240 W/cm2 and the stagnation pressures from 0.15 to 0.27 atm. (The maximum flight values are 132 W/cm2 and 0.25 atm) The majority of these runs were made at a nominal stagnation pressure of 0.25 atm. Two higher pressure runs were made to check the current (denser) ablation material for spallation, or other forms of thermal stress failure. Over 60% of the flatfaced models yielded good thermocouple data and all produced useful surface recession information. Of the five curved-edge models that were tested, only one gave good data; the remaining ones experienced model-holder failure. The test results can be summarized by noting that no failure of the ablative material was observed on any model. Also, the bondline temperature design limit of 250 C was never reached within an equivalent flight time despite a stagnation point heat load that exceeded the maximum flight value by up to 130%. At heating rates of over 200W/cm2 and stagnation pressures of 0.25 atm, or greater, the average surface recessions exceeded 0.5 cm on some models. The surface roughness increased dramatically at pressures above 0.25 atm and was four times greater at 0.27 atm than at 0.25 atm. Procured repair plug material performed much better than room-temperature cured plugs, as observed in the previous tests. Voids in the ablator did not increase local temperatures and gaps did not grow during testing.

Tran, Huy K.↗
NASA NTRS1994

Velocity correlations of galaxy clusters

We determine the velocity correlation function, pairwise peculiar velocity difference, and rms pairwise peculiar velocity dispersion of rich clusters of galaxies, as a function of pair separation, for three cosmological models: Omega = 1 and Omega = 0.3 cold dark matter (CDM), and Omega = 0.3 primeval baryonic isocurvature (PBI) models (all flat and Cosmic Background Explorer (COBE)-normalized). We find that close cluster pairs, with separation r is less than or equal to 10/h Mpc, exhibit strong attractive peculiar velocities in all models; the cluster pairwise velocities depend sensitively on the model. The mean pairwise attractive velocity of clusters on 5/h Mpc scale ranges from approximately 1700 km/s for Omega = 1 CDM to approximately 1000 km/s for PBI to approximately 700 km/s for Omega = 0.3 CDM. The small-scale pairwise velocities depend also on cluster mass: richer, more massive clusters exhibit stronger attractive velocities than less massive clusters. On large scales, from approximately 20 to 200/h Mpc, the cluster peculiar velocities are increasingly dominated by bulk and random motions; they are independent of cluster mass. The cluster velocity correlation function is negative on small scales for Omega = 1 and Omega = 0.3 CDM, indicating strong pairwise motion relative to bulk motion on small scales; PBI exhibits relatively larger bulk motions. The cluster velocity correlation function is positive on very large scales, from r approximately 10/h Mpc to r approximately 200/h Mpc, for all models. These positive correlations, which decrease monotonically with scale, indicate significant bulk motions of clusters up to approximately 200/h Mpc. The strong dependence of the cluster velocity functions on models, especially at small separations, makes them useful tools in constraining cosmological models when compared with observations.

Cen, Renyue↗
NASA NTRS2008

Five-Year Wilkinson Microwave Anisotropy Probe (WMAP) Observations: Likelihoods and Parameters from the WMAP Data

The Wilkinson Microwave Anisotropy Probe (WMAP), launched in 2001, has mapped out the Cosmic Microwave Background with unprecedented accuracy over the whole sky. Its observations have led to the establishment of a simple concordance cosmological model for the contents and evolution of the universe, consistent with virtually all other astronomical measurements. The WMAP first-year and three-year data have allowed us to place strong constraints on the parameters describing the ACDM model. a flat universe filled with baryons, cold dark matter, neutrinos. and a cosmological constant. with initial fluctuations described by nearly scale-invariant power law fluctuations, as well as placing limits on extensions to this simple model (Spergel et al. 2003. 2007). With all-sky measurements of the polarization anisotropy (Kogut et al. 2003; Page et al. 2007), two orders of magnitude smaller than the intensity fluctuations. WMAP has not only given us an additional picture of the universe as it transitioned from ionized to neutral at redshift z approx.1100. but also an observation of the later reionization of the universe by the first stars. In this paper we present cosmological constraints from WMAP alone. for both the ACDM model and a set of possible extensions. We also consider tlle consistency of WMAP constraints with other recent astronomical observations. This is one of seven five-year WMAP papers. Hinshaw et al. (2008) describe the data processing and basic results. Hill et al. (2008) present new beam models arid window functions, Gold et al. (2008) describe the emission from Galactic foregrounds, and Wright et al. (2008) the emission from extra-Galactic point sources. The angular power spectra are described in Nolta et al. (2008), and Komatsu et al. (2008) present and interpret cosmological constraints based on combining WMAP with other data. WMAP observations are used to produce full-sky maps of the CMB in five frequency bands centered at 23, 33, 41, 61, and 94 GHz (Hinshaw et al. 2008). With five years of data, we are now able to place better limits on the ACDM model. as well as to move beyond it to test the composition of the universe. details of reionization. sub-dominant components, characteristics of inflation, and primordial fluctuations. We have more than doubled the amount of polarized data used for cosmological analysis. allowing a better measure of the large-scale E-mode signal (Nolta et al. 2008). To this end we describe an alternative way to remove Galactic foregrounds from low resolution polarization maps in which Galactic emission is marginalized over, providing a cross-check of our results. With longer integration we also better probe the second and third acoustic peaks in the temperature angular power spectrum, and have many more year-to-year difference maps available for cross-checking systematic effects (Hinshaw et al. 2008).

Dunkey, J.↗
NASA NTRS1982

Some axisymmetric self-similar galaxy models

Distribution functions are presented for some axisymmetric self-similar galaxy models with flat rotation curves. In particular, we record velocity distribution functions for the logarithmic potentials studied by Richstone. These distribution functions depend on two integrals only. Other distribution functions (possibly involving more or other integrals) associated with the same mass model differ only by an additive function that integrates over velocities to yield zero density everywhere. However, a given distribution function can be associated with different mass models.

Miller, R. H.↗
NASA NTRS1976

Gamma rays and large scale galactic structure

Many theoretical models were developed in an attempt to explain the spatial structure in the observed emission which results from interactions of energetic cosmic rays with the interstellar gas. The peaks in the observed distribution are remarkably well correlated with longitudes corresponding to tangential directions to known spiral arm features. Based on theoretical and experimental arguments, it is assumed that on the scale of galactic arms the cosmic rays are more intense where the mass of the gas to which they are coupled is greatest. Refining this model with the results of recent surveys of the interstellar gas, a good fit to the observations is obtained whether the cosmic rays are confined to the spiral arms in the disk or are more evenly confined as in a flat halo model.

Kniffen, D. A.↗
NASA NTRS1983

An investigation of MAGSAT and complementary data emphasizing precambrian shields and adjacent areas of West Africa and South America

There is lack of acceptance of quantitative crustal models by specialists on regional geology because of the problem of east-west banding on MAGSAT anomaly maps. The possibility of some of the Earth's magnetic field being created in the mantle below the Curie isotherm is discussed as well as the need to remove spherical harmonics of degrees less than 15 from the anomaly map. Two dimensional models were produced for northern South America that might be considered as working models. These models suggest that the presumed Amazon River depression is better developed near Belem and in the upper Amazon basin than in the central Amazon basin. An attempt is proposed for separating the core field from the crustal field using a flat-Earth model.

Hastings, D. A.↗
NASA NTRS1995

Strut and wall interference on jet-induced ground effects of a STOVL aircraft in hover

A small scale ground effect test rig was used to study the ground plane flow field generated by a STOVL aircraft in hover. The objective of the research was to support NASA-Ames Research Center planning for the Large Scale Powered Model (LSPM) test for the ARPA-sponsored ASTOVL program. Specifically, small scale oil flow visualization studies were conducted to make a relative assessment of the aerodynamic interference of a proposed strut configuration and a wall configuration on the ground plane stagnation line. A simplified flat plate model representative of a generic jet-powered STOVL aircraft was used to simulate the LSPM. Cold air jets were used to simulate both the lift fan and the twin rear engines. Nozzle Pressure Ratios were used that closely represented those used on the LSPM tests. The flow visualization data clearly identified a shift in the stagnation line location for both the strut and the wall configuration. Considering the experimental uncertainty, it was concluded that either the strut configuration o r the wall configuration caused only a minor aerodynamic interference.

Kristy, Michael H.↗
NASA NTRS2014

Shielding Characteristics Using an Ultrasonic Configurable Fan Artificial Noise Source to Generate Modes - Experimental Measurements and Analytical Predictions

An Ultrasonic Configurable Fan Artificial Noise Source (UCFANS) was designed, built, and tested in support of the NASA Langley Research Center's 14x22 wind tunnel test of the Hybrid Wing Body (HWB) full 3-D 5.8% scale model. The UCFANS is a 5.8% rapid prototype scale model of a high-bypass turbofan engine that can generate the tonal signature of proposed engines using artificial sources (no flow). The purpose of the program was to provide an estimate of the acoustic shielding benefits possible from mounting an engine on the upper surface of a wing; a flat plate model was used as the shielding surface. Simple analytical simulations were used to preview the radiation patterns - Fresnel knife-edge diffraction was coupled with a dense phased array of point sources to compute shielded and unshielded sound pressure distributions for potential test geometries and excitation modes. Contour plots of sound pressure levels, and integrated power levels, from nacelle alone and shielded configurations for both the experimental measurements and the analytical predictions are presented in this paper.

Artifical Noise↗
NASA NTRS1993

Self-consistent models for triaxial galaxies with flat rotation curves - The disk case

We examine the possibility of constructing scale-free triaxial logarithmic potentials self-consistently, using Schwarzschild's linear programing method. In particular, we explore the limit of nonaxisymmetric disks. In this case it is possible to reduce the problem to the self-consistent reconstruction of the disk surface density on the unit circle, a considerably simpler problem than the usual 2D or 3D one. Models with surface densities of the form Sigma = (x exp n + (y/q) exp n) exp - 1/n with n = 2 or 4 are investigated. We show that the complicated shapes of the 'boxlet' orbit families (which replace the box orbit family found in potentials with smooth cores) limit the possibility of building self-consistent models, though elliptical disks of axis ratio above 0.7 and a restricted range of boxier models can be constructed. This result relies on using sufficiently fine bins, smaller than the 10 deg bins commonly used in 2D or 3D investigations. It also indicates the need for caution in interpreting N-body models of triaxial halos in which the core of the potential is numerically smoothed.

Kuijken, Konrad↗