Search NASA⌕ Search

SEARCH · Search NASA

Results for “flow direction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Experimental Investigation of a Phase Change Material Charged Finned-Tube Heat Exchanger

Understanding different thermal performance aspects of phase change material heat exchangers (PCM-HX) is critical for designing future energy-efficient thermal energy storage systems. This paper presents an experimental performance analysis of a vertically oriented annular finned-tube PCM-HX in a cylindrical container tested under six different melting and solidification test conditions, varied by heat transfer fluid’s (HTF) inlet temperatures and flow directions. The PCM-HX structure with 20 evenly spaced fins was 3D printed in aluminum, and the PCM-HX container was 285 mm in height. The PCM-HX average porosity was 89.7%, where the PCM mass was 246.4 g. Water served as the HTF, and a PCM with a nominal phase change temperature of 35 °C was selected. Instead of opaque conventional insulation sheets, a combination of air-and-argon-filled see-through insulation cylinders was assembled with the PCM-HX to visualize the phase-change phenomena, while minimizing the uncertainties due to heat loss. In total, there were 78 T-type thermocouples installed in the test section which allows a more precise assessment of thermal mass and heat loss, which are often neglected in similar studies found in the literature. We validated the reliability of the test facility as the repeated test results had negligible deviations under the same test conditions. The energy balances between the estimated theoretical and experimentally calculated PCM storage, considering heat loss and thermal mass, were within ±9% deviation for all test conditions. From the experimental investigations, we made several following observations. It was found that the melting pattern of the finned-tube PCM-HX with small gaps between the container wall and the fins was largely affected by the HTF flow directions, unlike the typical straight annular tube PCM-HX. For effective charging and discharging processes, a combination of upward melting and downward solidification is recommended to shorten the test duration. However, an upward solidification should be considered to minimize the cavity formation between the fins caused by the PCM volume contraction during the solidification process.

25 ENERGY STORAGE↗
DOE OSTI2025

Approaches for Water Removal in Direct-Fired sCO 2 Power Cycles

There is interest in investigation of water removal processes in direct fired sCO 2 flows, as this may potentially lead to greater system efficiency as the removal of this contaminant will result in sCO 2 behaving close to idealized behaviors. Water removal should be split into a two-step process, condensation of the water, followed by separation of the liquid phase water from the sCO 2 . The two main avenues of condensation are manipulation of pressure and temperature for phase change. For this paper, temperature-based phase change is the primary focus through the implementation of heat exchangers. Of the heat exchangers investigated it was found that printed circuit heat exchangers (PCHEs) could be an alternative for this use case, though the specific design of flow channel geometry and flow direction depends on the specific system case and cannot be determined at this point. For water separation there were four processes identified, all of which already assume water is in liquid phase at that point in the system. Of these separation avenues the best candidate is the hydrocyclone as it has a proven history of separating liquid-liquid phase mixtures with small density differences in oilfield use, in addition they have been investigated and modeled specifically for water separation for sCO 2 flows and the footprint is relatively small.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2024

Quantifying Dissolution Dynamics in Porous Media Using a Spatial Flow Focusing Profile

Abstract The diverse range of patterns in porous media formed by dissolution processes depends on the relative magnitude of flow, transport, and chemical reactions at pore surfaces. However, distinguishing between regimes often relies solely on qualitative, visual comparisons of emergent structures. Here, we propose a quantitative measure capable of identifying different regimes using the concept of the spatial flow focusing profile, which segments the medium into cross sections along the flow direction to calculate the flow focusing index for each section. We employ this measure in numerical simulations of a dissolving porous medium using a pore network model. We obtain a morphological phase diagram of dissolution patterns, which we characterize using the flow focusing profile. In particular, we demonstrate that analyzing the temporal changes in the profile allows one to quantitatively distinguish between wormholing and channeling. The transition between them is shown to be affected by the heterogeneity of the system.

58 GEOSCIENCES↗
DOE OSTI2025

Discrete global grid system-based flow routing datasets in the Amazon and Yukon basins

Abstract. Discrete global grid systems (DGGS) are emerging spatial data structures widely used to organize geospatial datasets across scales. While DGGS have found applications in various scientific disciplines, including atmospheric science and ecology, their integration into physically based hydrological models and Earth system models (ESMs) has been hindered by the lack of flow routing datasets based on DGGS. In response to this gap, this study pioneers the development of new flow routing datasets using icosahedral Snyder equal-area (ISEA) DGGS and a novel mesh-independent flow direction model. We present flow routing datasets for two large basins, the tropical Amazon River basin and the Arctic Yukon River basin. These datasets (1) facilitate the adoption of DGGS for hydrological models and (2) provide flow routing inputs for evaluation of DGGS-based flow routing in the Amazon and Yukon river basins. The data are available at https://doi.org/10.5281/zenodo.8377765 (Liao, 2023).

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

Minijet quenching in a concurrent jet + hydro evolution and the nonequilibrium quark-gluon plasma

Minijets, created by perturbative hard QCD collisions at moderate energies, can represent a significant portion of the total multiplicity of a heavy-ion collision event. Since their transverse momenta are initially larger than the typical saturation scale describing the bulk of the equilibrating quark-gluon plasma (QGP), they ought to be described through the physics of parton energy loss. Indeed, their typical stopping distances are larger than the usual hydrodynamization time, so they do not in general hydrodynamize at the same pace than the bulk of the collision. Therefore, in general minijets cannot be described solely by a unique preequilibrium stage that bridges the initial, overoccupied glasma state, with the hydrodynamical evolution. In this work we make use of a new concurrent minijet+hydrodynamic framework in which the properties of the hydrodynamically evolving QGP are modified due to the injection of energy and momentum from the minijets. We study the system for different choices of the minimum transverse momentum associated with minijet production. In order to achieve a realistic description of charged particle multiplicity, the amount of entropy associated to the low- x initial state needs to be reduced. Moreover, the fact that the injected momentum from the randomly oriented minijets is not correlated with the spatial gradients of the system reduces overall flow, and the value of the QGP transport coefficients needs to be reduced accordingly in order to describe the measured flow coefficients in experiments. They are, in effect, an important new source of fluctuations, resulting in a spikier, notably modified hydrodynamical evolution when compared to the scenario in which the presence of minijets is ignored. We avow that their abundance makes it necessary to include their physics in holistic descriptions of heavy-ion collisions. We discuss the impact of the minijets on a number of observables, such as p T spectra and p T -differential flow v n for a wide range of centrality classes. In contrast to elliptic, triangular or quadrangular flow, here we find that directed flow, v 1 , has the strongest potential to discriminate between different minijet production rates.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Resolving the mystery of electron perpendicular temperature spike in the plasma sheath

A large family of plasmas has collisional mean-free-path much longer than the non-neutral sheath width, which scales with the plasma Debye length. The plasmas, particularly the electrons, assume strong temperature anisotropy in the sheath. The temperature in the sheath flow direction (Te∥) is lower and drops toward the wall as a result of the decompressional cooling by the accelerating sheath flow. The electron temperature in the transverse direction of the flow field (Te⊥) not only is higher but also spikes up in the sheath. This abnormal behavior of Te⊥ spike is found to be the result of a negative gradient of the parallel heat flux of transverse degrees of freedom (qes) in the sheath. The non-zero heat flux qes is induced by pitch-angle scattering of electrons via either their interaction with self-excited electromagnetic waves in a nearly collisionless plasma or Coulomb collision in a collisional plasma, or both in the intermediate regime of plasma collisionality.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Flow reversal benchmark of a one-sided heated narrow rectangular channel with CATHARE and RELAP5

Flow reversal in narrow coolant channels can be a crucial phenomenon for the safety of research reactors with a downward nominal flow direction. During a loss of forced flow accident, the downward flow stagnates briefly before transitioning into an upward natural circulation flow. The fuel may be damaged if dryout occurs and threshold fuel and/or cladding temperatures are exceeded. A comprehensive study is provided for flow reversal in narrow rectangular channels by examining experimental data and conducting software model analyses. The literature on flow reversal was reviewed, and selected experimental datasets were used to benchmark against CATHARE and RELAP5 models and also compare the code calculations with each other. The experimental data comes from flow reversal tests conducted with a narrow rectangular channel with one-sided heating. The results were compared with experimental data for successful flow reversal tests and predicted dryout power for dryout conditions. Also, the study examined the effects of the pump coastdown period, inlet liquid temperature, system pressure, and localized pressure drops. The experimental results showed that shorter coastdown periods, reduced pressure drops, and lower coolant inlet temperatures increased the dryout power. However, the system pressure did not noticeably affect the results. The simulation results showed that both CATHARE and RELAP5 agreed with experimental data, capturing the trends of the experimental results. Slight differences between each code calculation, as well as the predicted and measured dryout powers, were attributed to experimental uncertainties and the modeling of physical phenomena such as wall nucleation, interfacial heat transfer, drag coefficients, and critical heat flux. Overall, this study provides an understanding of flow reversal and the prediction capabilities of thermal-hydraulics software models. In conclusion, a future study of the flow reversal benchmark of a narrow rectangular channel with two-sided heating may provide additional valuable insights.

CATHARE↗
DOE OSTI2025

Tunable reciprocal and nonreciprocal contributions to 1D Coulomb drag

Coulomb drag is a powerful tool to study interactions in coupled low-dimensional systems. Historically, Coulomb drag has been attributed to a frictional force arising from momentum transfer whose direction is dictated by the current flow. In the absence of electron-electron correlations, treating the Coulomb drag circuit as a rectifier of noise fluctuations yields similar conclusions about the reciprocal nature of Coulomb drag. In contrast, recent findings in one-dimensional systems have identified a nonreciprocal contribution to Coulomb drag that is independent of the current flow direction. In this work, we present Coulomb drag measurements between vertically coupled GaAs/AlGaAs quantum wires separated vertically by a hard barrier only 15 nm wide, where both reciprocal and nonreciprocal contributions to the drag signal are observed simultaneously, and whose relative magnitudes are temperature and gate tunable. Our study opens up the possibility of studying the physical mechanisms behind the onset of both Coulomb drag contributions simultaneously in a single device, ultimately leading to a better understanding of Luttinger liquids in multi-channel wires and paving the way for the creation of energy harvesting devices.

Coulomb Drag↗
DOE OSTI2024

Active nematic ratchet in asymmetric obstacle arrays

We numerically investigate the effect of an asymmetric periodic obstacle array in a two-dimensional active nematic. We find that activity in conjunction with the asymmetry leads to a ratchet effect or unidirectional flow of the fluid along the asymmetry direction. The directional flow is still present even in the active turbulent phase when the gap between obstacles is sufficiently small. We demonstrate that the dynamics of the topological defects transition from flow mirroring to smectic-like as the gap between obstacles is made smaller, and explain this transition in terms of the pinning of negative winding number defects between obstacles. This also leads to a nonmonotonic ratchet effect magnitude as a function of obstacle size, so that there is an optimal obstacle size for ratcheting at fixed activity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Active Nematic Ratchet in Asymmetric Obstacle Arrays

We numerically investigate the effect of an asymmetric periodic obstacle array in a two-dimensional active nematic. We find that activity in conjunction with the asymmetry leads to a ratchet effect or unidirectional flow of the fluid along the asymmetry direction. The directional flow is still present even in the active turbulent phase when the gap between obstacles is sufficiently small. We demonstrate that the dynamics of the topological defects transition from flow-mirroring to smectic-like as the gap between obstacles is made smaller, and explain this transition in terms of the pinning of negative winding number defects between obstacles. This also leads to a non-monotonic ratchet effect magnitude as a function of obstacle size, so that there is an optimal obstacle size for ratcheting at fixed activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

The Thermal Response of a Packed Bed Thermal Energy Storage System upon Saturated Steam Injection Using Distributed Temperature Sensing

The effectiveness of a thermal energy storage (TES) system is typically characterized with the help of thermal stratification or temperature gradients along the direction of heat injection, which is typically the flow direction of heat transfer fluid. The steepness of temperature gradients are a direct indicator of the effectiveness or efficiency of the heat storage or dispatch process. The temperature gradient evolution along the packed bed of ceramic particles upon saturated steam injection is presented in this work. Distributed temperature sensing based on optical frequency domain reflectometry was deployed in a packed bed of ceramic particles to capture the thermal front evolution in the axial direction. The physical processes accompanying steam injection in packed beds are complex due to phase change, transitioning two-phase flow, and changes in condensate accumulation. Therefore, the variation of thermal response of the TES system for various steam injection flow rates was experimentally studied using a high-resolution distributed temperature sensing system in a chemically inert alumina particle-packed bed. Distinct zones of different heat transfer modes were observed during the steam injection experiments. A distinct conduction zone, evident from diffuse thermal fronts, was observed at low flow rates, and these thermal gradients became sharper as the flow rate increased. The diffuse thermal fronts in the heat storage media suggest a low exergy efficiency of the TES system, as energy losses started initiating before a significant fraction of the bed was saturated with steam.

25 ENERGY STORAGE↗
DOE OSTI2021

Instrument for spatially resolved, temperature-dependent electrochemical impedance spectroscopy of thin films under locally controlled atmosphere

We demonstrate an instrument for spatially resolved measurements (mapping) of electrochemical impedance under various temperatures and gas environments. Automated measurements are controlled by a custom LabVIEW program, which manages probe motion, sample motion, temperature ramps, and potentiostat functions. Sample and probe positioning is provided by stepper motors. Dry or hydrated atmospheres (air or nitrogen) are available. The configurable heater reaches temperatures up to 500 °C, although the temperature at the sample surface is moderated by the gas flow rate. The local gas environment is controlled by directing flow toward the sample via a glass enclosure that surrounds the gold wire probe. Software and hardware selection and design are discussed. Reproducibility and accuracy are quantified on a Ba(Zr,Y)O 3-δ proton-conducting electrolyte thin film synthesized by pulsed laser deposition. The mapping feature of the instrument is demonstrated on a compositionally graded array of electrocatalytically active Ba(Co,Fe,Zr,Y)O 3-δ thin film microelectrodes. The resulting data indicate that this method proficiently maps property trends in these materials, thus demonstrating the reliability and usefulness of this method for investigating electrochemically active thin films.

47 OTHER INSTRUMENTATION↗
DOE OSTI2020

Bulk properties of the system formed in Au + Au collisions at s N N = 14.5 GeV at the BNL STAR detector

We report systematic measurements of bulk properties of the system created in Au+Au collisions at √ S NN = 14.5 GeV recorded by the STAR detector at the Relativistic Heavy Ion Collider (RHIC). The transverse momentum spectra of π ± , K ± and p(p¯) are studied at mid-rapidity (|y| < 0.1) for nine centrality intervals. The centrality, transverse momentum (p T ), and pseudorapidity (η) 3 dependence of inclusive charged particle elliptic flow (v 2 ), and rapidity-odd charged particles directed flow (v 1 ) results near mid-rapidity are also presented. These measurements are compared with the published results from Au+Au collisions at other energies, and from Pb+Pb collisions at √ S NN =2.76 TeV. The results at √ S NN = 14.5 GeV show similar behavior as established at other energies and fit well in the energy dependence trend. Furthermore, these results are important as the 14.5 GeV energy fills the gap in μ B, which is of the order of 100 MeV, between √ S NN =11.5 and 19.6 GeV. Comparisons of the data with UrQMD and AMPT models show poor agreement in general.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Delineation of endorheic drainage basins in the MERIT-Plus dataset for 5 and 15 minute upscaled river networks

Abstract The MERIT-Hydro networks re-gridded by the Iterative Hydrography Upscaling (IHU) algorithm do not retain exo- or endorheic basin attributes from the original data. Here we developed methods to assign such attributes to those and any other digital river networks. The motivation is that endorheic inland drainage basins are essential for hydrologic modelling of global and regional water balances, land surface water storage, gravity anomalies, sea level rise, etc. First, we create basin attributes that explicitly label endorheic and exorheic catchments by the criteria of direct or hidden connectivity to the ocean without changing their flow direction grid. In the second step we alter the delineation of endorheic basins by the merging algorithm that eliminates small inland watersheds to the adjacent host basins. The resulting datasets have a significantly reduced number of endorheic basins while preserving the total land portion and topology of the inland basins. The data was validated using the Water Balance Model by comparing volume of endorheic inland depressions with modelled water accumulation in their inland lakes.

58 GEOSCIENCES↗
DOE OSTI2024

Verification and Validation of Spectral Element Code for Supercritical CO2 Flow in Vertical Heated Tubes

The investigation of heat transfer in supercritical CO2 (sCO2) has garnered considerable attention in recent decades, given sCO2's potential as a promising working fluid for advanced power conversion cycles. Despite previous research efforts, there are still gaps in our understanding of sCO2 heat transfer, particularly in conditions associated with heat transfer deterioration. To delve into sCO2 heat transfer more comprehensively, we propose employing the high-fidelity computational fluid dynamics code NekRS to simulate sCO2 flow using the large eddy simulation technique. Through graphics processing unit acceleration, NekRS achieves a higher computational speed than traditional CPU-based systems. However, before using NekRS in practical applications involving sCO2, it is imperative to perform verification and validation. Here, this paper presents our efforts to verify and validate the NekRS code's capability for simulating sCO2 using heated vertical tubes, where heat transfer deterioration usually happens. To accommodate the unique properties of sCO2, we have modified the NekRS code by integrating third-party property modules, such as REFPROP and PROPATH. Our simulations are compared with experimental and numerical data from the literature, instilling confidence in leveraging NekRS for future engineering applications. Our simulations also reveal that the accuracy of the property module significantly impacts the results, with REFPROP outperforming PROPATH for sCO2 properties. Additionally, we observed that, depending on the flow direction, buoyancy can either enhance or suppress turbulence in sCO2 flow. In upward flow, under certain conditions, the suppressed turbulence leads to heat transfer deterioration, resulting in elevated wall temperatures.

NekRS↗
DOE OSTI2023

Direct Expansion Heat Pump Using High Glide Low GWP Refrigerant

Next generation of refrigerants require drastically lower global warming potential (GWP). The refrigerant mixtures, with a GWP < 150, e.g., R-457A, etc., tend to have significant temperature glide, which prefer multi-row, cross counter flow configuration. Typical heat pump operation reverses the refrigerant flow direction, compared to the air flow, from cooling mode to heating mode. It is difficult to configurate cross counter-flow heat exchangers in heat pumps. We invented an innovative configuration, having check valve assembly to maintain uniform cross counter flow configuration in both cooling and heat modes, which optimizes the performance of a high temperature slide refrigerant mixture, i.e. R-457A. Based on it, we developed a laboratory prototype, using a 2-stage compressor, achieved a cooling SEER (cooling seasonal energy efficiency rating) of 16.0 (cooling seasonal COP of 4.69) and a heating HSPF (heating seasonal performance factor) > 9.5 (heating seasonal COP of 2.78). The unit was tested in an extensive ambient condition, heating operation from 5˚F to 62˚F (-15˚C to 16.7˚C); cooling operation from 82˚F to 95˚F (27.8˚C to 35˚C). The paper will introduce the system configuration, heat exchanger dimensions and laboratory investigations.

Shen, Bo↗