Search NASA⌕ Search

SEARCH · Search NASA

Results for “flowability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Vibration induced active rheology control for 3D concrete printing

3D concrete printing, an emerging automation technology for construction, requires the concrete to be flowable during pumping and extrusion but firm immediately after layer deposition. This study investigated an active rheology control using vibration to achieve these opposing requirements. The effects of vibration frequency and acceleration on rheological parameters of concrete were studied with different levels of nanoparticles in the mix. It was found that extrusion pressure and yield stress show less sensitivity to the peak velocity of the vibration up to a certain level and then they both decrease beyond this level. Also, certain level of nanoparticles inclusion found to double the reduction in extrusion pressure and yield stress. Buildability studies using 3D printers were conducted to demonstrate the active rheology control using vibration. The mechanical properties of the printed structures were also found to have improved when vibration rheology control was used.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effect of PCEs with different structures on hydration and properties of cementitious materials with low water-to-binder ratio

Polycarboxylate ethers (PCEs) with different structures and densities of anchor groups in the backbone were synthesized and characterized. The surface tension of their solutions, their adsorption on cementitious particles and zeta potential of cement-silica fume pastes with PCEs were measured. Their effects on hydration and properties of cement-silica fume paste with low water-to-binder ratio were examined. Results indicated that the adsorption kinetics of theses PCEs on cementitious particles are fitted the pseudo-second-order model. The introduction of long silane chain on PCE decreased its electrostatic adsorption, while PCE was adsorbed onto the surface of particles via both chemical and electrostatic adsorption, when silicon hydroxyl is directly connected to its backbone. In the presence of PCE with higher adsorbed amount, pastes exhibited lower yield stress and higher flowability, and higher strength at 7 d and 28 d. The low plastic viscosity, autogenous and drying shrinkage were related to the low surface tension of PCE solution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the use of limestone calcined clay cement (LC3) in high-strength strain-hardening cement-based composites (HS-SHCC)

Highlights: • Use of LC{sup 3} slightly reduces flowability and shortens the setting time of fresh matrices. • Highly polymerized C-A-S-H gel and abundant ettringite benefit flexural strength of LC{sup 3}-matrices. • Use of LC{sup 3} enhances the bond strength between fiber and high-strength matrix. • LC{sup 3}-based HS-SHCC yields similar flexural performance as the composite with Portland cement. High-strength strain-hardening cement-based composites (HS-SHCC) demonstrate excellent mechanical and durability properties. However, high cement content typical to HS-SHCC results not only in high carbon footprint, but also in excessive hydration heat and severe autogenous shrinkage. In this investigation, Limestone Calcined Clay Cement (LC{sup 3}) was used to produce sustainable HS-SHCC. The LC{sup 3} substitution resulted in higher energy consumption during mixing and in shorter setting times of the fresh, plain matrices. Although the LC{sup 3} substitution slightly reduced the compressive strength, the formation of highly polymerized C-A-S-H gel and abundant ettringite benefited the flexural strength of the plain matrices. Additionally, single-fiber pullout experiments showed that the use of LC{sup 3} led to increased fiber-matrix bond strength and pullout energy. Finally, the replacement of Portland cement by LC{sup 3} resulted in HS-SHCC with similar mechanical performance to the reference composite, indicating a high potential for using LC{sup 3} in high-performance cement-based composites.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A review of the effect of nanoclays on the fresh and hardened properties of cement-based materials

This paper provides an overview of the use of nanoclays in cement-based materials. The effect of nanoclays on shear rheological properties will be discussed, with a focus on structural build-up behavior. This macroscale flow behavior will then be tied to the effect of nanoclays on the fresh microstructure as characterized via in-situ particle size measurements and rheological techniques. This will provide insight on the mechanisms underlying the effect of nanoclays on fresh state properties through an improved understanding of their effect on flocculation and coagulation behavior. In addition, secondary effects nanoclays have on the hardening and hardened properties will also be discussed. Examples of casting applications in which nanoclays have been effectively utilized as rheological modifiers, i.e. reducing self-consolidating concrete formwork pressure, extrusion, semi-flowable concrete for slipform paving, and 3D concrete printing, will be presented. Finally, some thoughts on potential directions for future work will be shared.

36 MATERIALS SCIENCE↗
DOE OSTI2021

3D printing of calcined clay-limestone-based cementitious materials

This paper aims to investigate the influences of high Portland cement substitutions (>60 wt%) by low-grade calcined clay (CC) and limestone (LF) on 3D concrete printability, stiffness evolution and early-age hydration. Results show that, with the same dosage of admixtures (superplasticizer and viscosity modifier), increasing LF and CC content reduced the slump, flowability and initial material flow rate, and significantly improved the buildability of fresh mixtures, which can be attributed to the reduced water film thickness (WFT). Furthermore, the stiffness evolution and SSA{sub total} development up to the first 3 h were accelerated by increasing CC content, which can also be linked to the change of WFT, and consumption of superplasticizer for the dispersion induced by hydration products. Additionally, the dilution effect on compressive strength and hydration caused by the high cement replacement was observed.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Production of mechanically-generated 316L stainless steel feedstock and its performance in directed energy deposition processing as compared to gas-atomized powder

The objective of this work is to study the feasibility of mechanically-generated feedstock for use in directed energy deposition (DED) processing. Mechanically-generated powder was created by machining 316L stainless steel bar stock followed by comminution of the resulting chips through oscillation ball milling. This methodology's production yield and processing time for the specifications of a commercially available DED system are presented along with resulting powder morphology. Performance of the mechanically-generated feedstock was compared to gas-atomized powder and evaluated based on the following figures of merit: flowability, printed part height, printed part density, and chemical compositional stability throughout processing. Mechanically-generated feedstock was created to meet deposition system requirements. Compared with gas-atomized powder, mechanically-generated powder did not flow as well through the powder-delivery system. Parts printed from mechanically-generated feedstock were generally taller than their counterparts from gas-atomized feedstock, but their densities were less predictable. As a result, chemical composition of prints using both feedstocks was within standard nominal compositions for 316L stainless steel.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Numerical framework for integrated additive manufacturing-compression molding (AM-CM) of thermoplastic composites

Additive manufacturing-compression molding (AM-CM) has emerged as a transformative technology in advanced composite manufacturing. Additive manufacturing (AM) offers high design flexibility and the ability to produce complex geometries with precisely aligned fibers in the preferred orientation. Compression molding (CM) enhances composite materials by providing excellent dimensional stability, reduced porosity, high production rates, and a smooth surface finish. Despite these advantages, extensive integrated analysis is required to optimize processing conditions for improved fiber orientation distribution (FOD) and porosity control. Here, this study develops a comprehensive numerical model to simulate the AM-CM manufacturing process. The model isolates the effects of both the AM and CM phases while also capturing their integration. Additionally, it accounts for heat transfer, temperature-dependent viscosity, and fiber orientation in the extruded fiber-filled polymer, accurately representing material behavior during processing. This approach enables the analysis of interactions between deposited beads of complex strand shapes and their interface regions after full compression. Moreover, the model predicts key parameters such as polymer flowability, fiber orientation, and temperature evolution in AM-CM parts. By optimizing processing conditions, it facilitates a controlled and predictable microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Pathways to formulate lightweight and ultra-lightweight 3D printable cementitious composites

Here, this paper studies the pathways to formulate lightweight and ultra-lightweight 3D printable cementitious composites. A hybrid approach was proposed by combining the advantages of traditional chemical-induced foaming (foaming approach) and lightweight particulate inclusions (synthetic foam approach). A comprehensive experimental program was conducted to evaluate the effects of foaming agents and fly ash cenosphere (FAC) on the printability, microstructure, mechanical and thermal properties of 3D printed samples. The results showed that the hybrid approach could produce a mixture with a density as low as 470 kg/m 3 while ensuring good flowability and buildability owing to the lubricating effect of foaming and supporting skeleton formed by FAC. In addition, a three-step homogenization procedure was also developed to predict the effective elastic modulus and thermal conductivity of 3D printable cementitious composites and cementitious foam. The findings of the study highlighted the effectiveness of the hybrid approach in formulating 3D printable ultra-lightweight cementitious composites in thermal insulation and acoustic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Safety perceptions of solid-state lithium metal batteries

Safety concerns hamper the wide application of lithium-ion batteries (LIBs) in the fields of electric vehicles and stationary energy storage. As the blame of the battery thermal runway was widely cast on the flowable, volatile, and flammable nature of liquid organic electrolytes, solid-state lithium batteries with solid and nonflammable electrolytes are highly praised for potentially better safety characteristics. Furthermore, solid-state lithium metal batteries (SS-LMBs) may become an ultimate solution for safe, high-energy density batteries. Whether SS-LMBs are safe enough to meet emerging demands remains unclear, as recent publications have presented serious safety concerns at both the material and device levels. In conclusion, this review summarizes recent investigations into SS-LMB safety, and systematic analysis and discussion are provided in this discussion of the safety concerns of SS-LMBs.

25 ENERGY STORAGE↗
DOE OSTI2021

Fatigue of laser powder bed fusion processed 17-4 stainless steel using prior process exposed powder feedstock

The rapid pace of development seen in the metal additive manufacturing (AM) process of laser powder-bed fusion (LPBF) requires in-step advances in processes qualification to enable full-scale adoption. This particularly applies to quantifying how powder feedstock conditions impact end-component quality. Here this study examines how in-machine 17-4 stainless steel powder feedstocks are affected by prior LPBF processes, and how these effects impact subsequent builds. Examinations of powder morphology, chemistry, flowability, and rheology were conducted to characterize the powder conditions. The resultant effects of powder feedstock condition on produced component quasi-static tensile and high-cycle fatigue properties were analyzed. Fatigue life was analyzed using a reliability modeling approach that enabled a robust statistical comparison of life. Powder characteristics were found to evolve with powder exposure to prior LPBF processes, particularly in the extremes of powder size distribution and measures of bulk flow. No significant effects of these changes on tensile properties were observed. Reliability modeling methods, including the lognormal and Weibull distributions as well as the empirical survival function, are shown to be effective tools for modeling fatigue variability in LPBF manufactured components. Through these tools, fatigue life was found to be invariant with changes in powder condition.

42 ENGINEERING↗
DOE OSTI2022

Zero carbon solid-state rechargeable redox fuel for long duration and seasonal storage

Here, this work presents a unique thermochemical process for charging magnesium-manganese-oxide-based solid-state rechargeable redox fuel. High-temperature heating of the processing furnace can be driven by either renewable electricity or concentrated solar power. The simple recyclable fuel charging concept is based on a tubular falling bed reactor with countercurrent oxygen-depleted gas flow for complete heat recuperation. The main focus of this work is achieving solid flowability at high temperatures (1,450°C) and extracting chemically charged solid at ambient temperature with minimal energy loss. The operation strategies described in this work have enabled consistent magnesium-manganese-oxide particle flow up to 1,450°C. The measured extent of the thermal reduction reaction after cooling the particles is more than 90% of the fully reduced state at equilibrium. The thermal-to-chemical efficiency and overall system efficiency are 96% and 35% respectively, which are the highest reported for thermochemical fuels to date.

25 ENERGY STORAGE↗
DOE OSTI2023

Additive manufacturing of nickel-based superalloys: A state-of-the-art review on process-structure-defect-property relationship

Fusion-based additive manufacturing (AM) has significantly grown to fabricate Nickel-based superalloys with design freedom across multiple length scales. Several phenomena such as feedstock/energy source/melt pool interactions, solidification and phase transformations occur during fusion-based AM processes of Nickel-based superalloys, which determine the ultimate microstructure and mechanical performance of the built parts. In this review, here we elaborate a comprehensive discussion on AM Nickel-based superalloys and influential factors including feedstock characteristics (powder morphology, chemistry, contamination, flowability, recycling) and AM processing (parameters, and powder spreading/wall/balling/spattering effects) on their microstructure (micro-segregation, phases formations and grain structures), defect generation (sub-surface/internal defects, microcracks, surface roughness, and residual stress). Furthermore, the mechanical properties of AM Nickel-based superalloys such as tensile, creep and fatigue at room/elevated temperatures are analyzed in accordance with the initial, and post processing effects. Additionally, the commonly utilized modeling approaches in literature to predict the microstructure and mechanical behavior of these alloys are highlighted. Finally, the current challenges and mitigation approaches for future research are identified considering the gaps in the AM Nickel-based superalloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rheological effects of moisture content on the anatomical fractions of loblolly pine (Pinus taeda)

Here, this study focused on assessing the influence of moisture content on the rheological properties of different anatomical fractions of pine residue using the FT4 powder rheometer. Moisture content exhibited some influence on the 2 mm bark and needle fractions, increasing their cohesion, angle of internal friction, unconfined yield strength, and major principal stress. Stem and whole, on the other hand, presented minimal changes upon moisture introduction. All 4 mm fractions did not show many changes in their rheological properties with moisture introduction, which can be due to less particle-particle interactions and consequently reducing any liquid bridging the particles might undergo; however, they were shown to have a more unpredictable behavior compared to the 2 mm analogues (i.e., higher standard deviation) which can be due to a higher degree of particle-interlocking. Out of the three fractions, needle presented the poorest rheological properties for flowability in addition to being susceptible by moisture, unlike other fractions.

36 MATERIALS SCIENCE↗
DOE OSTI2023

SPH modeling of biomass granular flow: Theoretical implementation and experimental validation

The commercialization of biomass-derived energy is impeded by flowability challenges arising from the feeding and handling of granular biomass materials in full-scale biorefineries. To overcome these obstacles, a robust and accurate model to simulate the flow of granular biomass is indispensable. However, conventional mesh-based numerical codes are limited by inherent mesh distortion in simulating large deformation that commonly occurs in granular biomass handling. Here, in this study, we propose a graphics processing unit (GPU)-accelerated meshless Smoothed Particle Hydrodynamics (SPH) code to model the flow of granular biomass materials. A modified void ratio-based mass conversation, a hybrid particle-to-particle/surface frictional boundary treatment, and a hypoplastic constitutive model are implemented. Four numerical examples, an elastic block sliding on inclined planes, sand column collapse, Angle of Repose, and axial compression tests for pine chips, were simulated using the developed SPH code. The results demonstrate good agreement between numerical predictions and analytical and experimental data for all four examples, validating the SPH code and increasing confidence that it can be applied to simulate more complex granular biomass handling processes, such as hopper feeding or auger conveyance.

09 BIOMASS FUELS↗
DOE OSTI2024

Shear rate dependency on flowing granular biomass material

The commercialization of bioenergy has been significantly limited by various material handling issues due to the poor flowability of granular biomass materials. A good understanding of flow physics and robust constitutive models to predict flow behavior across multiple regimes are essential to address these issues. In this study, we investigated the multi-regime flow behavior of loblolly pine chips, a widely used bioenergy feedstock, through comprehensive inclined plane flow experiments and simulations. A quasi-static hypoplastic model and a cross-regime Drucker-Prager-µ(I) model were calibrated and validated against the physical experiments to investigate the quasi-static and dense flow behavior. The results show that for granular biomass, 1) plane flow (iso-thickness along the plane) exists within a smaller range of inclination while heap flow (varying thickness along the plane) exists within a broader range of inclination, as compared with conventional granular materials (e.g., glass beads); 2) the scaling law of granular biomass flowing on an inclined plane (Froude Number versus dimensionless thickness) forms a bi-linear trend with the turning point governed by the quasi-static and dense flow regimes; 3) the multi-regime DP-µ(I) model can capture the flow behavior in both regimes well at the cost of extra calibration. In conclusion, these findings advance the scientific understanding of the multi-regime flow behavior of granular biomass materials and shed light on formulating novel constitutive models to assist granular biomass handling in the bioenergy industry.

09 BIOMASS FUELS↗
DOE OSTI2023

The significance of biomass densification in biological-based biorefineries: A critical review

Replacing fossil fuels with renewable biofuels derived from lignocellulosic biomass is an important aspect of addressing environmental challenges and developing a sustainable industrial society. Densification overcomes the problems of low bulk density and poor flowability of biomass and has been commercialized for producing solid biofuels, but the overall impact of densification on biological-based biorefineries that primarily target liquid fuels (e.g., ethanol) is still under investigation. Herein, this review provides a thorough summary of the application of densified biomass in biological-based biorefineries. First, the effects of densification parameters as well as variables of biomass materials on the densified products’ quality are reviewed, and different commonly used densification technologies are also discussed and compared. Then, the discussion focuses on the physiochemical modifications of biomass caused by densification that may influence further pretreatment and/or enzymatic hydrolysis in biorefineries. Industrial pelleting has been generally shown to exhibit positive/neutral effects on the enzymatic hydrolysis of multiple biomass feedstocks after pretreatments, indicating the viability of using pellets as starting feedstocks in biorefineries. Densification causes structural disruption of biomass, which may facilitate further biochemical conversions. Integrating biomass densification in the feedstock supply chain is feasible for large-scale biorefineries to overcome the techno-economic barriers and become profitable. Suggestions are presented for the efficiency enhancement and cost reduction in densification-based biorefineries. To enable wider applications, it is now the time to employ more demo and full-scale activities in different regions of the world pushing the research and innovation of densification integrated within biorefining.

09 BIOMASS FUELS↗
DOE OSTI2021

Discovery of Energy Storage Molecular Materials Using Quantum Chemistry-Guided Multiobjective Bayesian Optimization

Redox flow batteries (RFBs) are a promising technology for stationary energy storage applications due to their flexible design, scalability, and low cost. In RFBs, energy is carried in flowable redoxactive materials (redoxmers) which are stored externally and pumped to the cell during operation. Further improvements in the energy density of RFBs necessitates redoxmer designs with wider redox potential windows and higher solubility. Additionally, designing redoxmers with a fluorescence-enabled self-reporting functionality allows monitoring of the state of health of RFBs. To accelerate the discovery of redoxmers with desired properties, state-of-the- art machine learning ( ML) methods, such as multiobjective Bayesian optimization (MBO), are useful. Here, we first employed density functional theory calculations to generate a database of reduction potentials, solvation free energies, and absorption wavelengths for 1400 redoxmer molecules based on a 2,1,3-benzothiadiazole (BzNSN) core structure. From the computed properties, we identified 22 Pareto-optimal molecules that represent best trade-off among all of the desired properties. We further utilized these data to develop and benchmark an MBO approach to identify candidates quickly and efficiently with multiple targeted properties. With MBO, optimal candidates from the 1400-molecule data set can be identified at least 15 times more efficiently compared to the brute force or random selection approach. Importantly, we utilized this approach for discovering promising redoxmers from an unseen database of 1 million BzNSN-based molecules, where we discovered 16 new Pareto-optimal molecules with significant improvements in properties over the initial 1400 molecules. Furthermore, we anticipate that this active learning technique is general and can be utilized for the discovery of any class of functional materials that satisfies multiple desired property criteria.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Effects of Particle Mixing and Gravitational Settling on Charge Transport in Carbon Flow-Electrode Cells

Flowable carbon slurries are actively studied and under development for charge transport in various electrochemical systems including flow capacitors, capacitive deionization cells, semi-solid flow batteries, and lithium extraction. However, much less is known about in operando slurry flow dynamics and their corresponding effect on charge transport. We performed an experimental study of mixing and settling dynamics of slurry electrodes within an electrochemical flow cell during continuous operations. The electrochemical cell consisted of two horizontal co-flowing channels, separated by a cation-exchange membrane (CEM). Here we used high-speed optical imaging of planes parallel to gravity and simultaneous electrochemical measurements. At low flow rates, dense yet dynamic particle beds formed on the bottom electrode in each channel, which unexpectedly yielded the highest currents. This approach enables the operation of the flow cell at low system-average particle concentrations while leveraging gravity-driven particle settling to locally enhance carbon concentrations precisely at the current collector sites. Conversely, high flow rates were characterized by thin particle beds and well-mixed particle flows. In the latter case, the electrodes in closest proximity (located on either side of the CEM) achieved a current higher than the other electrode pairs. The observations have implications for slurry control and electrode designs in electrochemical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗