Search NASA⌕ Search

SEARCH · Search NASA

Results for “grouping optimization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Ultra-efficient Engine Diameter Study

Engine fan diameter and Bypass Ratio (BPR) optimization studies have been conducted since the beginning of the turbofan age with the recognition that reducing the engine core jet velocity and increasing fan mass flow rate generally increases propulsive efficiency. However, performance tradeoffs limit the amount of fan flow achievable without reducing airplane efficiency. This study identifies the optimum engine fan diameter and BPR, given the advanced Ultra-Efficient Engine Technology (UEET) powerplant efficiencies, for use on an advanced subsonic airframe. Engine diameter studies have historically focused on specific engine size options, and were limited by existing technology and transportation infrastructure (e.g., ability to fit bare engines through aircraft doors and into cargo holds). This study is unique in defining the optimum fan diameter and drivers for future 2015 (UEET) powerplants while not limiting engine fan diameter by external constraints. This report follows on to a study identifying the system integration issues of UEET engines. This Engine Diameter study was managed by Boeing Phantom Works, Seattle, Washington through the NASA Glenn Revolutionary Aero Space Engine Research (RASER) contract under task order 10. Boeing Phantom Works, Huntington Beach, completed the engine/airplane sizing optimization, while the Boeing Commercial Airplane group (BCA) provided design oversight. A separate subcontract to support the overall project was issued to Tuskegee University.

Daggett, David L.↗
NASA NTRS2006

Accuracy of High-Rate GPS for Seismology

We built a device for translating a GPS antenna on a positioning table to simulate the ground motions caused by an earthquake. The earthquake simulator is accurate to better than 0.1 mm in position, and provides the "ground truth" displacements for assessing the technique of high-rate GPS. We found that the root-mean-square error of the 1-Hz GPS position estimates over the 15-min duration of the simulated seismic event was 2.5 mm, with approximately 96% of the observations in error by less than 5 mm, and is independent of GPS antenna motion. The error spectrum of the GPS estimates is approximately flicker noise, with a 50% decorrelation time for the position error of approx.1.6 s. We that, for the particular event simulated, the spectrum of dependent error in the GPS measurements. surface deformations exceeds the GPS error spectrum within a finite band. More studies are required to determine whether a generally optimal bandwidth exists for a target group of seismic events.

Elosegui, P.↗
NASA NTRS2023

Leveraging Automated Fiber Placement Computer Aided Process Planning Framework for Defect Validation and Dynamic Layup Strategies

Process planning represents an essential stage of the Automated Fiber Placement (AFP) workflow. It develops useful and efficient machine processes based upon the working material, composite design, and manufacturing resources. The current state of process planning requires a high degree of interaction from the process planner and could greatly benefit from increased automation. Therefore, a list of key steps and functions are created to identify the more difficult and time-consuming phases of process planning. Additionally, a set of metrics must exist by which to evaluate the effectiveness of the manufactured laminate from the machine code created during the Process Planning stage. Layup strategies, in addition to dog ears, stagger shifts, steering constraints, and starting points, represented the group of functions labeled as process optimization and ranked the highest in terms of priority for automation. The laminates resulting from the selected parameters are evaluated through the occurrences of principal defect metrics such as fiber gaps, overlaps, angle deviation and steering violations. This document presents an automated software solution to the layup strategy and starting point selection phase of process planning. A series of ply scenarios are generated with variations of these ply parameters and evaluated according to a set of metrics entered by the Process Planner. These metrics are generated through use of the Analytical Hierarchy Process (AHP), where relative importance between each of the fiber features are defined. The ply scenarios are selected which reduce the overall fiber feature scores based on the defects the Process Planner wishes to minimize.

HiCAM↗
NASA NTRSDate not supplied

Hamiltonian Optimal Control of Distributed Lagrangian Systems

This lecture presents a Hamiltonian control method and a distributed optimal control method for distributed Lagrangian systems. The distributed optimal control theory is formulated using a semi-group abstraction resulting in an integro-differential Riccati equation.

Distributed Optimal Control↗
NASA NTRS1990

Several families of viscous optimized waveriders - A review of waverider research at the University of Maryland

Theoretical and experimental research conducted by the Hypersonic Group at the University of Maryland in the area of viscous optimized waveriders is reviewed. In particular, the motivation for this class of waveriders is discussed, and results obtained to date are presented. Various waverider families generated from different flows and designed for different applications are examined, including waveriders using chemically reacting flow effects and very high altitude applications.

Anderson, John D., Jr.↗
NASA NTRS2000

Annual Research Briefs - 2000: Center for Turbulence Research

This report contains the 2000 annual progress reports of the postdoctoral Fellows and visiting scholars of the Center for Turbulence Research (CTR). It summarizes the research efforts undertaken under the core CTR program. Last year, CTR sponsored sixteen resident Postdoctoral Fellows, nine Research Associates, and two Senior Research Fellows, hosted seven short term visitors, and supported four doctoral students. The Research Associates are supported by the Departments of Defense and Energy. The reports in this volume are divided into five groups. The first group largely consists of the new areas of interest at CTR. It includes efficient algorithms for molecular dynamics, stability in protoplanetary disks, and experimental and numerical applications of evolutionary optimization algorithms for jet flow control. The next group of reports is in experimental, theoretical, and numerical modeling efforts in turbulent combustion. As more challenging computations are attempted, the need for additional theoretical and experimental studies in combustion has emerged. A pacing item for computation of nonpremixed combustion is the prediction of extinction and re-ignition phenomena, which is currently being addressed at CTR. The third group of reports is in the development of accurate and efficient numerical methods, which has always been an important part of CTR's work. This is the tool development part of the program which supports our high fidelity numerical simulations in such areas as turbulence in complex geometries, hypersonics, and acoustics. The final two groups of reports are concerned with LES and RANS prediction methods. There has been significant progress in wall modeling for LES of high Reynolds number turbulence and in validation of the v(exp 2) - f model for industrial applications.

Source record↗
NASA NTRS1993

Uncertainty reasoning in expert systems

Intelligent control is a very successful way to transform the expert's knowledge of the type 'if the velocity is big and the distance from the object is small, hit the brakes and decelerate as fast as possible' into an actual control. To apply this transformation, one must choose appropriate methods for reasoning with uncertainty, i.e., one must: (1) choose the representation for words like 'small', 'big'; (2) choose operations corresponding to 'and' and 'or'; (3) choose a method that transforms the resulting uncertain control recommendations into a precise control strategy. The wrong choice can drastically affect the quality of the resulting control, so the problem of choosing the right procedure is very important. From a mathematical viewpoint these choice problems correspond to non-linear optimization and are therefore extremely difficult. In this project, a new mathematical formalism (based on group theory) is developed that allows us to solve the problem of optimal choice and thus: (1) explain why the existing choices are really the best (in some situations); (2) explain a rather mysterious fact that fuzzy control (i.e., control based on the experts' knowledge) is often better than the control by these same experts; and (3) give choice recommendations for the cases when traditional choices do not work.

Kreinovich, Vladik↗
NASA NTRS2015

Global Precipitation Measurement (GPM) Mission: Precipitation Processing System (PPS) GPM Mission Gridded Text Products Provide Surface Precipitation Retrievals

In February 2015, the Global Precipitation Measurement (GPM) mission core satellite will complete its first year in space. The core satellite carries a conically scanning microwave imager called the GPM Microwave Imager (GMI), which also has 166 GHz and 183 GHz frequency channels. The GPM core satellite also carries a dual frequency radar (DPR) which operates at Ku frequency, similar to the Tropical Rainfall Measuring Mission (TRMM) Precipitation Radar, and a new Ka frequency. The precipitation processing system (PPS) is producing swath-based instantaneous precipitation retrievals from GMI, both radars including a dual-frequency product, and a combined GMIDPR precipitation retrieval. These level 2 products are written in the HDF5 format and have many additional parameters beyond surface precipitation that are organized into appropriate groups. While these retrieval algorithms were developed prior to launch and are not optimal, these algorithms are producing very creditable retrievals. It is appropriate for a wide group of users to have access to the GPM retrievals. However, for researchers requiring only surface precipitation, these L2 swath products can appear to be very intimidating and they certainly do contain many more variables than the average researcher needs. Some researchers desire only surface retrievals stored in a simple easily accessible format. In response, PPS has begun to produce gridded text based products that contain just the most widely used variables for each instrument (surface rainfall rate, fraction liquid, fraction convective) in a single line for each grid box that contains one or more observations.This paper will describe the gridded data products that are being produced and provide an overview of their content. Currently two types of gridded products are being produced: (1) surface precipitation retrievals from the core satellite instruments GMI, DPR, and combined GMIDPR (2) surface precipitation retrievals for the partner constellation satellites. Both of these gridded products are generated for a.25 degree x.25 degree hourly grid, which are packaged into daily ASCII (American Standard Code for Information Interchange) files that can downloaded from the PPS FTP (File Transfer Protocol) site. To reduce the download size, the files are compressed using the gzip utility.This paper will focus on presenting high-level details about the gridded text product being generated from the instruments on the GPM core satellite. But summary information will also be presented about the partner radiometer gridded product. All retrievals for the partner radiometer are done using the GPROF2014 algorithmusing as input the PPS generated inter-calibrated 1C product for the radiometer.

precipitation↗
NASA NTRS1996

Integrating a Genetic Algorithm Into a Knowledge-Based System for Ordering Complex Design Processes

The design cycle associated with large engineering systems requires an initial decomposition of the complex system into design processes which are coupled through the transference of output data. Some of these design processes may be grouped into iterative subcycles. In analyzing or optimizing such a coupled system, it is essential to be able to determine the best ordering of the processes within these subcycles to reduce design cycle time and cost. Many decomposition approaches assume the capability is available to determine what design processes and couplings exist and what order of execution will be imposed during the design cycle. Unfortunately, this is often a complex problem and beyond the capabilities of a human design manager. A new feature, a genetic algorithm, has been added to DeMAID (Design Manager's Aid for Intelligent Decomposition) to allow the design manager to rapidly examine many different combinations of ordering processes in an iterative subcycle and to optimize the ordering based on cost, time, and iteration requirements. Two sample test cases are presented to show the effects of optimizing the ordering with a genetic algorithm.

Rogers, James L.↗
NASA NTRS1996

1996 Coolant Flow Management Workshop

The following compilation of documents includes a list of the 66 attendees, a copy of the viewgraphs presented, and a summary of the discussions held after each session at the 1996 Coolant Flow Management Workshop held at the Ohio Aerospace Institute, adjacent to the NASA Lewis Research Center, Cleveland, Ohio on December 12-13, 1996. The workshop was organized by H. Joseph Gladden and Steven A. Hippensteele of NASA Lewis Research Center. Participants in this workshop included Coolant Flow Management team members from NASA Lewis, their support service contractors, the turbine engine companies, and the universities. The participants were involved with research projects, contracts and grants relating to: (1) details of turbine internal passages, (2) computational film cooling capabilities, and (3) the effects of heat transfer on both sides. The purpose of the workshop was to assemble the team members, along with others who work in gas turbine cooling research, to discuss needed research and recommend approaches that can be incorporated into the Center's Coolant Flow Management program. The workshop was divided into three sessions: (1) Internal Coolant Passage Presentations, (2) Film Cooling Presentations, and (3) Coolant Flow Integration and Optimization. Following each session there was a group discussion period.

Steven A. Hippensteele↗
NASA NTRS2001

Algorithms and Object-Oriented Software for Distributed Physics-Based Modeling

The project seeks to develop methods to more efficiently simulate aerospace vehicles. The goals are to reduce model development time, increase accuracy (e.g.,by allowing the integration of multidisciplinary models), facilitate collaboration by geographically- distributed groups of engineers, support uncertainty analysis and optimization, reduce hardware costs, and increase execution speeds. These problems are the subject of considerable contemporary research (e.g., Biedron et al. 1999; Heath and Dick, 2000).

Kenton, Marc A.↗
NASA NTRS1990

Ellipsometric study of cubic SiC

Variable angle spectroscopic ellipsometry (VASE) was applied to cubic SiC. This technique gives absolute values of the refractive index (n) and the extinction coefficient (k) of a substrate and/or a thin film of unknown material. The samples were grown by chemical vapor deposition (CVD) on p-type silicon. The substrate was aligned either on the (001) axis or 1 degree of (001). Several growth temperatures and growth durations were used. The samples were divided into two groups: (1) thick films of order 10 microns grown near optimal conditions of temperature, flow, and gas ratio; and (2) thin films of order 100 A grown at various temperatures. The ellipsometric results for samples in group 1 were analyzed using a two-phase model (substrate and ambient). Results show that for wavelengths in the visible, the refractive index of these CVD samples is equal to that reported for single crystal cubic SiC, within the experimental error, which is on the order of 1 percent. However, the extinction coefficient has a relatively large value, even above the band gap. The absorption is sample dependent and has a broad peak in the visible. The results for samples in group 2 were analyzed using a three-phase model (substrate, film, and ambient). The dielectric functions of the film, deducted from the measured n and k, were further analyzed using the effective medium approximation. The results show that the films contain 30 to 40 vol. percent amorphous silicon, i.e., silicon with only short-range order.

Alterovitz, Samuel A.↗
NASA NTRS1981

Image registration system in the Landsat-D production environment

It is the purpose of the considered system to take pieces of imagery, called control point chips (CPC), whose geodetic location has been previously determined and stored, and locate their position in later imagery of the same area. The registration processes are carried out partially on a DEC VAX 780 computer and partially on a Floating Point Systems Array Processor. Typically sets of 20 control points are processed at a time. To process these as sets, and to optimize the use of both machines, operations are grouped into loops instead of a sequential processing for each point. Attention is given to cloud cover assessment, enhancement, correlation techniques, pixel registration, and subpixel registration.

Kiss, P.↗
NASA NTRS1997

Software Design Improvements: Software Quality and the Design and Inspection Process - Part 2

The application of assurance engineering techniques improves the duration of failure-free performance of software. The totality of features and characteristics of a software product are what determine its ability to satisfy customer needs. Software in safety-critical systems is very important to NASA. We follow the System Safety Working Groups definition for system safety software as: 'The optimization of system safety in the design, development, use and maintenance of software and its integration with safety-critical systems in an operational environment. 'If it is not safe, say so' has become our motto. This paper goes over methods that have been used by NASA to make software design improvements by focusing on software quality and the design and inspection process.

Lalli, Vincent R.↗
NASA NTRS2001

Spectroscopic Determination of the Physical Conditions in Hot, Optically Thin Sources

This annual report covers the period from Oct 1, 2000 to Sep 30, 2001. The Astrophysics Plasma Emission Code and Database (APEC/APED), developed in part under this grant, have been upgraded to Version 1.1 and are now beginning to be used outside our research group in applications to X-ray spectral data from Chandra and XMM-Newton. These models represent the best theoretical data currently available and are reasonably complete below about 30 angstroms. Stellar coronae are being used to benchmark the atomic data in APED as part of the Emission Line Project. Initial results suggest that the models for most of the strongest lines are in good agreement with the observations, including the H-like and He-like emission from dominant elements and the Fe L shell emission, both near 1 keV and in the extreme ultraviolet near 100 eV. At this point in time, we define 'good agreement' at the level of accuracy expected from the atomic physics, approximately 20-30%. In order to benchmark the spectral models beyond the canonical theoretical accuracy, we are working closely with the Chandra gratings calibration group to ensure that we are using the optimal calibration, primarily effective areas and line response functions.

Brickhouse, N.↗
NASA NTRS2005

Fiber Reinforced Composite Materials Used for Tankage

The Nonmetallic Materials and Processes Group is presently working on several projects to optimize cost while providing effect materials for the space program. One factor that must be considered is that these materials must meet certain weight requirements. Composites contribute greatly to this effort. Through the use of composites the cost of launching payloads into orbit will be reduced to one-tenth of the current cost. This research project involved composites used for aluminum pressure vessels. These tanks are used to store cryogenic liquids during flight. The tanks need some type of reinforcement. Steel was considered, but added too much weight. As a result, fiber was chosen. Presently, only carbon fibers with epoxy resin are wrapped around the vessels as a primary source of reinforcement. Carbon fibers are lightweight, yet high strength. The carbon fibers are wet wound onto the pressure vessels. This was done using the ENTEC Filament Winding Machine. It was thought that an additional layer of fiber would aid in reinforcement as well as containment and impact reduction. Kevlar was selected because it is light weight, but five times stronger that steel. This is the same fiber that is used to make bullet-proof vests trampolines, and tennis rackets.

Cunningham, Christy↗
NASA NTRS2018

Transcriptomics and Proteomics Discussion

This presentation will cover the the basic pipelines for transcriptomics and proteomics that the GeneLab Analysis Working Groups (AWGs) have so far determined to be optimal. Basic transcriptomic pipelines will first be presented from primary analysis to higher-order systems analysis. Examples of how the data has been analyzed will be presented. Proteomics pipelines will also be presented compiled from various AWG members. Discussion will be generated from the AWG members to reach a consensus for each omic type.

Transcriptomics↗
NASA NTRS2013

Next Generation Lightweight Mirror Modeling Software

The advances in manufacturing techniques for lightweight mirrors, such as EXELSIS deep core low temperature fusion, Corning's continued improvements in the Frit bonding process and the ability to cast large complex designs, combined with water-jet and conventional diamond machining of glasses and ceramics has created the need for more efficient means of generating finite element models of these structures. Traditional methods of assembling 400,000 + element models can take weeks of effort, severely limiting the range of possible optimization variables. This paper will introduce model generation software developed under NASA sponsorship for the design of both terrestrial and space based mirrors. The software deals with any current mirror manufacturing technique, single substrates, multiple arrays of substrates, as well as the ability to merge submodels into a single large model. The modeler generates both mirror and suspension system elements, suspensions can be created either for each individual petal or the whole mirror. A typical model generation of 250,000 nodes and 450,000 elements only takes 5-10 minutes, much of that time being variable input time. The program can create input decks for ANSYS, ABAQUS and NASTRAN. An archive/retrieval system permits creation of complete trade studies, varying cell size, depth, and petal size, suspension geometry with the ability to recall a particular set of parameters and make small or large changes with ease. The input decks created by the modeler are text files which can be modified by any editor, all the key shell thickness parameters are accessible and comments in deck identify which groups of elements are associated with these parameters. This again makes optimization easier. With ANSYS decks, the nodes representing support attachments are grouped into components; in ABAQUS these are SETS and in NASTRAN as GRIDPOINT SETS, this make integration of these models into large telescope or satellite models possible.

Arnold, William↗