SEARCH · Search NASA

Results for “high current density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Direct coronal heating from dissipation of magnetic field

The visible corona of the Sun appears to be heated by direct dissipation of magnetic fields. The magnetic fields in the visible corona are tied at both ends to the photosphere where the active convection continually rotates and shuffles the footpoints in a random pattern. The twisting and wrapping of flux tubes about each other produce magnetic neutral sheets in a state of dynamical nonequilibrium such that the current sheets become increasingly concentrated with the passage of time. Dissipation of the high current densities takes place regardless of the high electrical conductivity of the fluid. The convection on the feet of the lines of force at the surface of the Sun goes directly (within a matter of 10 to 20 hours) into heat in the corona. The rate of doing work seems adequate to supply the necessary 10 to the 7th power ergs/square cm. sec for the active corona.

Parker, E. N.↗

NASA NTRS1977

A hollow cathode hydrogen ion source

High current density ion sources have been used to heat plasmas in controlled thermonuclear reaction experiments. High beam currents imply relatively high emission currents from cathodes which have generally taken the form of tungsten filaments. This paper describes a hydrogen ion source which was primarily developed to assess the emission current capability and design requirements for hollow cathodes for application in neutral injection devices. The hydrogen source produced ions by electron bombardment via a single hollow cathode. Source design followed mercury ion thruster technology, using a weak magnetic field to enhance ionization efficiency. A 1.3-cm-diam hollow cathode using a low work function material dispenser performed satisfactorily over a discharge current range of 10-90 A. Cylindrical probe measurements taken without ion extraction indicate maximum ion number densities on the order of 10 trillion/cu cm. Discharge durations ranged from 30 sec to continuous operation. Tests with beam extraction at 2.5 keV and 30 A discharge current yield average ion beam current densities of 0.1 A/sq cm over a 5-cm extraction diameter. Results of this study can be used to supply the baseline information needed to scale hollow cathodes for operation at discharge currents of hundreds of amperes using distributed cathodes.

Sovey, J. S.↗

DOE OSTI2025

Quaternary Cu 2 TSiS 4 (T = Fe, Mn) Anodes for Li-Ion Batteries

Developing high-capacity and fast-charging anode materials is critical for achieving high-performance Li-ion batteries (LIBs). Herein, polycrystalline quaternary transition metal silicon sulfides, Cu 2 TSiS 4 (T = Fe, Mn), were synthesized using a solid-state method and investigated as anode materials in LIBs. Cu 2 FeSiS 4 retains a reversible capacity of 670 mAh g –1 at 200 mA g –1 for 400 cycles, while Cu 2 MnSiS 4 suffers from a fast capacity loss in the initial 50 cycles. More importantly, Cu 2 FeSiS 4 can maintain a reversible capacity of 379 mAh g –1 after 700 cycles at a high current density of 2 A g –1 , demonstrating high cyclic stability and fast-charging capacity. To further understand the structure degradation and phase transformation, we investigated the postcycling electrodes using multiple techniques, including the scanning electron microscope with energy-dispersive X-ray spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy techniques. The results indicated that Cu 2 FeSiS 4 undergoes reversible phase transitions with Li 2 S as a major product component. To further assess the performance for practical applications, Cu 2 FeSiS 4 was coupled with LiFePO 4 to make LiFePO 4 ||Cu 2 FeSiS 4 full cells, which delivered superior electrochemical performance. These results demonstrate great promise for using quaternary transition metal silicon sulfides as anodes to achieve low-cost and sustainable LIBs.

25 ENERGY STORAGE↗

DOE OSTI2025

Editors’ Choice—Molten Salt Electrolysis in Chloride Melts for Energy-Efficient Iron Metal Production

This study explores chloride molten salt electrolysis (CMSE) as a promising route for energy-efficient iron metal (Fe) production. Moderate temperature (500 °C) LiCl-KCl molten salts offer excellent thermodynamic stability, high ionic conductivity and diffusivity, and high solubility for FeCl 3 , thereby enabling efficient Fe metal extraction at high electrowinning rates. Here, we demonstrate the two essential steps for converting taconite ore into Fe metal. First, Fe 2 O 3 from taconite pellets was selectively leached in HCl yielding a high-purity FeCl 3 aqueous solution, while the gangue components settled at the bottom. Then, anhydrous FeCl 3 was electrolyzed in a LiCl-KCl eutectic molten salt at 500 °C at high current density (1 A cm −2 ) and at high Coulombic efficiency (>85%). Analysis of the electrowon Fe deposits revealed dendritic structures with purity of >99 wt%, which could be further improved to nearly 100 wt% through arc re-melting. CMSE offers low specific energy consumption (3.7 kWhr kg −1 ), competitive with H 2 -DRI and other electrolytic approaches being pursued globally. Our findings underscore the potential of CMSE as an energy-efficient route for electrosynthesis of Fe metal.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Magnesium‐Mediated Electrochemical Synthesis of Ammonia

Metal-mediated electrochemical synthesis of ammonia (NH3) is a promising method to activate N2 at room temperature. While a Li-mediated approach has been optimized to produce NH3 at high current density and selectivity, Li's scarcity and its highly negative plating potential limit scalability and energy efficiency. Alternative mediators have been proposed, but only Ca has shown some promise, achieving ≈50% Faradaic efficiency (FE), though requiring voltages beyond -3 V. Here, we report a Mg-mediated nitrogen reduction reaction (Mg-NRR), where N2 is activated on Mg to form Mg3N2, followed by protolysis to release NH3 and regenerate Mg. A notable NH3 FE of 25.28 ± 3.80% is achieved at a current density of -45 mA cm-2, corresponding to an NH3 partial current density of -11.30 ± 1.77 mA cm-2 under 6 bar N2. Isotope-labeled experiments confirm that NH3 originates from N2, with similar FE (25.15 ± 1.01%). Importantly, NH3 production is demonstrated at a total cell potential as low as -3 V. This Li-free Mg-NRR system offers key advantages, including lower energy input and use of earth-abundant materials, making it a scalable route for sustainable NH3 synthesis.

Goyal, Ishita↗

NASA NTRS1993

A High Performance H2-Cl2 Fuel Cell for Space Power Applications

NASA has numerous airborne/spaceborne applications for which high power and energy density power sources are needed. The proton exchange membrane fuel cell (PEMFC) is an attractive candidate for such a power source. PEMFC's offer many advantages for airborne/spaceborne applications. They have high power and energy densities, convert fuel to electrical power with high efficiency at both part and full load, and can rapidly startup and shutdown. In addition, PEMFC's are lightweight and operate silently. A significant impediment to the attainment of very high power and energy densities by PEMFC's is their current exclusive reliance on oxygen as the oxidant. Conventional PEMFC's oxidize hydrogen at the anode and reduce oxygen at the cathode. The electrode kinetics of oxygen reduction are known to be highly irreversible, incurring large overpotential losses. In addition, the modest open circuit potential of 1.2V for the H2-O2 fuel cell is unattainable due to mixed potential effects at the oxygen electrode. Because of the high overpotential losses, cells using H2 and O2 are capable of achieving high current densities only at very low cell voltages, greatly curtailing their power output. Based on experimental work on chlorine reduction in a gas diffusion electrode, we believe significant increases in both the energy and power densities of PEMFC systems can be achieved by employing chlorine as an alternative oxidant.

Anderson, Everett B.↗

NASA NTRS1977

A hollow cathode hydrogen ion source

Sovey, J. S.↗

NASA NTRSDate not supplied

Electrifying Aircraft Propulsion: Thermal Issues of Megawatt Scale Power Dense Electric Machines and Material Solutions

Aircraft are the last major mode of transportation to undergo electrification for many reasons, where the underlying reason is the sensitivity of aircraft performance to mass. This sensitivity demands that efficient, megawatt (MW)-scale high specific power density powertrains be developed to impact regional, single aisle and larger aircraft that account for the majority of fuel burn in commercial aviation. Developing MW-scale high specific power electric powertrains (machines, cables/busbars and power electronics) remains a significant challenge. While advanced power semiconductors have enabled higher voltages, densities, and operational frequencies this also leads to passing high current through smaller volumes when considering electric machines and power electronics. This poses significant thermal challenges. This is particularly true for electric machines that strive to surpass 13 kW/kg, which studies have shown to be desirable for electric aircraft propulsion. The necessity of handling high current densities to achieve MW power levels dictates that greater than 10kW of waste heat will be generated. Moreover, most of the heat is generated in the stator winding which is a mixture of electrical conductor (copper or aluminum), potting material, magnet wire (electrical) insulation and high voltage electrical insulation. Although the electrical conductor is a fantastic thermal conductor, it is also the source of the heat (carrying the electrical current) and is thermally isolated by the other materials. Simply letting the machine run at increased temperatures is an attractive idea, however the reality is that most of the suitable electric insulations and potting material candidates are not likely to satisfactorily operate at higher temperatures with reasonable life expectancies. The likelihood of developing new polymers that can satisfy the necessary functions (mechanical and electrical), operate at higher temperatures with acceptable lifetime in the near term is small. This has led the researchers at the NASA Glenn Research Center to examine electrically insulative materials in high power destiny electric machines, their thermal environment, and what solutions are realistic from a materials point of view. This presentation will touch on both the thermal challenges of electric machines and NASA Glenn’s research into material solutions.

Electric Aircraft Propulsion↗

NASA NTRS1991

Performance of NbN superconductive tunnel junctions as SIS mixers at 205 GHz

Small area (less than 1 sq micron), high-current-density NbN/MgO/NbN tunnel junctions with I-V characteristics suitable for high-frequency mixers have been fabricated. Mesa-geometry junctions with an area of about 1 sq micron and critical current density of 5-10 kA/sq cm are integrated with superconducting microstrip lines designed to resonate out the junction capacitance. A study was made of the mixer gain and noise performance near 205 GHz as a function of the inductance provided by the microstrip line. This has confirmed, at a high millimeter-wave frequency, values of junction capacitance of 85 fF/sq micron and recently measured values of a magnetic penetration depth of 380 nm. Mixer noise temperatures as low as 134 K at 1.5 K have been obtained for properly tuned junctions. A significant improvement in mixer performance on cooling from 4.2 K to 1.5 K was observed. Edge-geometry junctions with an area of 0.3 sq microns and critical current density of 18-25 kA/sq cm have also been fabricated. These junctions give a mixer noise temperature of 145 K at 4.2 K without the use of integrated tuning elements. These are the best results ever achieved for NbN-based SIS mixers.

Mcgrath, W. R.↗

NASA NTRS1992

Temperature dependence of the electrode kinetics of oxygen reduction at the platinum/Nafion interface - A microelectrode investigation

Results of a study of the temperature dependence of the oxygen reduction kinetics at the Pt/Nafion interface are presented. This study was carried out in the temperature range of 30-80 C and at 5 atm of oxygen pressure. The results showed a linear increase of the Tafel slope with temperature in the low current density region, but the Tafel slope was found to be independent of temperature in the high current density region. The values of the activation energy for oxygen reduction at the platinum/Nafion interface are nearly the same as those obtained at the platinum/trifluoromethane sulfonic acid interface but less than values obtained at the Pt/H3PO4 and Pt/HClO4 interfaces. The diffusion coefficient of oxygen in Nafion increases with temperature while its solubility decreases with temperature. These temperatures also depend on the water content of the membrane.

Parthasarathy, Arvind↗

NASA NTRS2017

Silicon-Based Lithium-Ion Capacitor for High Energy and High Power Application

Si-based Li-ion capacitor has been developed and demonstrated. The results show it is feasible to improve both power density and energy density in this configuration. The applied current density impacts the power and energy density: low current favors energy density while high current favors power density. Active carbon has a better rate capability than Si. Next StepsFuture Directions. Si electrode needs to be further studied and improved. Further optimization of SiAC ratio and evaluation of its impact on energy density and power density.

Wu, James J.↗

DOE OSTI2024

Ameliorating the sodium storage performance of hard carbon anode through rational modulation of binder

Hard carbon anodes have emerged as promising candidates for sodium-ion batteries due to their inherent advantages. Nevertheless, the surface imperfections in these materials often culminate in irreversible electrolyte consumption, fostering the development of a heterogeneous and fragile solid electrolyte interface (SEI), thereby compromising the initial Coulombic efficiency (ICE). Here, drawing inspiration from the catalytic potential of C=O (carbonyl) bonds in directing preferential salt reduction, we introduce a novel strategy that leverages the modulation of the binder, a long-term overlooked pivotal components in the electrode process. Specifically, Polymethyl methacrylate (PMMA), abundant in C=O groups, is partially substituted for PVDF, ensuring robust adhesion of the electrode material to the current collector while preserving superior mechanical properties. The accurate combination of two binders with delightful compatibility in the state-of-art electrode process, can promote a uniform formation of the SEI on the hard carbon surface enriched in inorganic components, which can ensure long-term interfacial stability and suppresses excessive solvent decomposition and facilitates Na + transfer at the interface. Consequently, the initial Coulombic efficiency of the hard carbon anode with 70 %PMMA binder achieves 86 %, with prominent cycling stability (88 % capacity retention over 500 cycles) at a high current density of 1.2 A g −1 . When paired with high loading cathodes to assemble the pouch cell, it also demonstrates stable operational scenarios.

25 ENERGY STORAGE↗

DOE OSTI2025

Spin State Modulation via Magnetic Fields in Fe Single Atom Catalysts for High-Performance Aqueous Zinc–Sulfur Batteries

Aqueous zinc–sulfur battery has garnered significant attention as a high-energy, low-cost, and safe energy storage system. However, the multielectron transfer kinetics of sulfur cathodes are relatively slow, presenting challenges such as limited sulfur utilization and lower discharge voltage, which significantly hinder their practical applications. Here, in this study, we explored a comprehensive design approach for high-performance, long-cycle aqueous zinc–sulfur batteries. The simultaneous introduction of ZnI 2 and Fe single atoms (Fe-SAs) as catalytically active agents decouples the redox reactions, effectively facilitating ZnS oxidation and S reduction separately. The application of an external magnetic field regulates the spin state of Fe-SAs, further enhancing their catalytic activity and electron transfer capability. Electrochemical tests demonstrate that the S@Fe-NC HS/ZnI 2 cathode assembled under a magnetic field exhibits excellent rate performance, achieving an impressive specific capacity of 1399 mAh g –1 at a high current density of 5 A g –1 and good cycling stability over 300 cycles, representing the highest reported high-current discharge capacity to date. This study provides a comprehensive design framework for optimizing zinc–sulfur (Zn–S) battery performance and elucidates the influence of magnetic field-induced spin state modulation on catalytic behavior.

36 MATERIALS SCIENCE↗

NASA NTRS1970

High energy density electrochemical cell

Primary cell has an anode of lithium, a cathode containing dihaloisocyanuric acid, and a nonaqueous electrolyte comprised of a solution of lithium perchlorate in methyl formate. It produces an energy density of 213 watt hrs/lb and can achieve a high current density.

Byrne, J. J.↗

DOE OSTI2025

Morphological Degradation of Oxygen Evolution Reaction-Electrocatalyzing Nickel Selenides at Industrially Relevant Current Densities

We investigated electrodeposited nanoparticulate nickel selenide (pre)catalysts that transform into nickel oxides/ oxyhydroxides under oxygen evolution reaction conditions in alkaline solutions. Previous studies of this transformation were conducted at lower current densities than those of industrial relevance (≥1 A cm −2 ). We used ultramicroelectrodes (UMEs) to achieve such current densities, benefiting from their small size, ensuring low absolute currents and low ohmic drop but high current densities. Morphological degradation of the catalyst material was only observed at current densities exceeding 1 A cm −2 but not for smaller ones. Using X-ray absorption, Xray photoemission spectroscopy, and X-ray diffraction, we confirmed that the degradation was accompanied by the literature-known transformation of nanoparticulate Ni 3 Se 2 (bulk)/NiSe (surface) into nickel oxyhydroxide. The transformation of the precatalyst goes along with a significant improvement in the charge transfer kinetics observed by decreasing Tafel slopes with ongoing experimental time extracted from cyclic voltammetry (CV) experiments and electrochemical impedance spectroscopy (EIS) in the high-frequency range. However, these kinetic improvements are accompanied by limitations in mass transport concluded from decreasing current responses at high overpotentials in CVs and increasing impedance in the low-frequency range of the EIS spectra after extended CV cycling. These mass transport limitations originated from morphological degradations at the UME exceeding 1 A cm −2 which we proved by applying identical location scanning electron microscopy. This has not been reported in studies that have been limited to lower current densities before. Our findings showcase how UMEs can be used to study (pre)catalysts (herein nickel selenides) under current densities of industrial relevance in the absence of ohmic drop-related ambiguities, combined with in-depth materials characterization studies, e.g., identical location microscopy and advanced spectroscopic methods. This approach enables direct evaluation and comparison of catalyst materials and thus demonstrates how to overcome long-standing limitations of electrocatalyst design and testing.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2025

Enhancing surface activity and durability in triple conducting electrode for protonic ceramic electrochemical cells

With the material system operating at lower temperatures, protonic ceramic electrochemical cells (PCECs) can offer high energy efficiency and reliable performance for both power generation and hydrogen production, making them a promising technology for reversible energy cycling. However, PCEC faces technical challenges, particularly regarding electrode activity and durability under high current density operations. To address these challenges, we introduce a nano-architecture oxygen electrode characterized by high porosity and triple conductivity, designed to enhance catalytic activity and interfacial stability through a self-assembly approach, while maintaining scalability. Electrochemical cells incorporating this advanced electrode demonstrate robust performance, achieving a peak power density of 1.50 W cm −2 at 600 °C in fuel cell mode and a current density of 5.04 A cm −2 at 1.60 V in electrolysis mode, with enhanced stability on transient operations and thermal cycles. The underlying mechanisms are closely related to the improved surface activity and mass transfer due to the dual features of the electrode structure. Additionally, the enhanced interfacial bonding between the oxygen electrode and electrolyte contributes to increased durability and thermomechanical integrity. This study underscores the critical importance of optimizing electrode microstructure to achieve a balance between surface activity and durability.

Protonic Ceramic Electrochemical Cells↗

NASA NTRS1990

Performance of all-NbN superconductive tunnel junctions as mixers at 205 GHz

Small-area (1x1 sq micron) high-current-density NbN-MgO-NbN tunnel junctions with I-V characteristics suitable for high frequency mixers were fabricated. These junctions are integrated with superconducting microstrip lines designed to resonate out the large junction capacitance. The mixer gain and noise performance were studied near 205 GHz as a function of the inductance provided by the microstrip. This has yielded values of junction capacitance of 85 fF/sq microns and magnetic penetration depth of 3800 angstroms. Mixer noise as low as 133 K has been obtained for properly tuned junctions. This is the best noise performance ever reported for an NbN SIS mixer.

Mcgrath, W. R.↗

NASA NTRS1972

Thin film fuel cell electrodes.

Earlier work shows that fuel cell electrodes prepared by sputtering thin films of platinum on porous vycor substrates avoid diffusion limitations even at high current densities. The presented study shows that the specific activity of sputtered platinum is not unusually high. Performance limitations are found to be controlled by physical processes, even at low loadings. Catalyst activity is strongly influenced by platinum sputtering parameters, which seemingly change the surface area of the catalyst layer. The use of porous nickel as a substrate shows that pore size of the substrate is an important parameter. It is noted that electrode performance increases with increasing loading for catalyst layers up to two microns thick, thus showing the physical properties of the sputtered layer to be different from platinum foil. Electrode performance is also sensitive to changing differential pressure across the electrode. The application of sputtered catalyst layers to fuel cell matrices for the purpose of obtaining thin total cells appears feasible.

Asher, W. J.↗