Search NASA⌕ Search

SEARCH · Search NASA

Results for “hopper design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A deep insight on the coal ash-to-slag transformation behavior during the entrained flow gasification process

Recent research provided deep insight on the coal ash-to-slag transformation characterization during the entrained flow gasification process, with experimentation on a 40 kg/hr (dry basis) coal-fed opposed multi-burner (OMB) entrained flow gasifier and simulation via FactSage™ software. A general mechanism is presented to relate the gasifier design temperature, ash fluid temperature, and operating temperature with the degree of the slag polymerization. The change of the high temperature zone, the corresponding particle residence time in the high temperature zone, and syngas composition have obvious effects on the slag mineral transformation behavior. Mineral types formed on the wall of the gasifier chamber were mainly anorthite (CaAl 2 Si 2 O 8 ), aluminum oxide (Al 2 O 3 ), and calcium sulfide (CaS). These minerals transformed to anorthite and diopside (CaMgSi 2 O 6 ) at the slag hole zone, while the minerals at the lock hopper were anorthite, orthoclase (KAlSi 3 O 8 ), quartz (SiO 2 ), gypsum (CaSO 4 ), calcite (CaCO 3 ), and halite (NaCl). FactSage™ predicted minerals as anorthite, diopside, orthoclase, and albite (NaAlSi 3 O 8 ), etc., where the slag temperature was below the ash fluid temperature and when the ratios of CO/CO 2 and (CO + H 2 )/CO 2 were lower than 1.0 and 2.0, respectively. By simulation, residual carbon was found to be the dominant factor over syngas composition to cause mineral transformation, and this was verified experimentally. The Ca-based crystals, typically anorthite, was shifted to diopside, near the slag hole zone, and a linear relationship was found between the content ratios of diopside/(anorthite + diopside), CaO/SiO 2 , and (CaO + MgO)/SiO 2 . A dimensionless number, θ, was defined to characterize the changing chemical composition and the degree of slag polymerization, with temperature deviation from the design condition. Three zones of θ were identified and related to the deviation between the actual gasification condition from the design condition. Finally, a low slag polymerization degree corresponded with a higher temperature deviation between the actual condition and design condition, and this proved that increased residual carbon content and changing iron valence state increased the mineral types when the slag temperature was below the ash fluid temperature.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

SPH Modeling of Biomass Granular Flow: Engineering Application in Hoppers and Augers

Numerical modeling of granular biomass material flow in handling operations is indispensable to decipher flow upsets, commonly manifested as clogging and jamming in hoppers and augers. With a computational tool developed based on smoothed particle hydrodynamics (SPH), we simulated the hopper flow and auger feeding of six granular biomass materials. The good agreement between the experimental and numerical flow rates demonstrated the capability of the developed SPH solver in modeling the complicated flow of granular biomass materials. Further, the impact of physical and numerical parameters is investigated, and the major results show that the hopper flow pattern is controlled by shear band evolution; hopper clogging is collectively influenced by the opening size, wall friction, and material packing, and the impact of material compressibility on the auger feed rate is minimal. These parametric studies validate the solver’s robustness in simulating biomass flow in handling equipment and demonstrate that the SPH computational tool can provide insights about granular flow mechanics to facilitate handling equipment design and optimize handling operations.

09 BIOMASS FUELS↗
NASA NTRS2018

Pluto Hop, Skip, and Jump

This is the Final Report from Global Aerospace Corporation on this NIAC effort (Grant Nos.: NNX17AJ71G and 80NSSC18K0062) to develop the Pluto Hop, Skip, and Jump mission concept. We sought out to establish the feasibility of using a large inflatable drag device to decelerate and land on Pluto from interplanetary speed (~14 km/s) using only the Pluto atmosphere and just a few kilograms of propellant. The design and analysis efforts in Phase I indicated that this is feasible. Aerodynamic heating and loads were found to be orders of magnitude less than typical planetary entries due to the ultra-low ballistic coefficient craft and the low density and large scale height of the Pluto atmosphere. The deceleration system is capable of delivering a 200-kg lander-hopper to the surface or inserting an orbiter of a similar mass using aerocapture. Mission analysis work led to a reference mission with Earth launch in 2029, Jupiter assist in 2030, and Pluto arrival in 2040.

Goldman, Benjamin↗
NASA NTRS1971

The lunar hopping transporter

Research on several aspects of lunar transport using the hopping mode is reported. Hopping exploits the weak lunar gravity, permits fuel economy because of partial recompression of propellant gas on landing, and does not require a continuous smooth surface for operation. Three questions critical to the design of a lunar hopping vehicle are addressed directly in this report: (1) the tolerance of a human pilot for repeated accelerations; (2) means for controlling vehicle attitude during ballistic flight; and (3) means of propulsion. In addition, a small scale terrestrial demonstrator built to confirm feasibility of the proposed operational mode is described, along with results of preliminary study of unmanned hoppers for moon exploration.

Degner, R.↗
DOE OSTI2020

Characterizing material transitions in large-scale Additive Manufacturing

Integrating Multiple Materials (MM) into large-scale Additive Manufacturing (AM) is a key for various industrial applications wishing to incorporate site-specific properties into geometrically complex designs that are difficult to manufacture with traditional techniques. Printing with multiple materials is typically accomplished by using layers as natural material boundaries, but having the capability to switch between materials within a single layer without pausing would further expand MM possibilities. This study used Cincinnati Incorporated’s Big Area Additive Manufacturing (BAAM) system to explore material transitions with a novel dual-hopper that enables in-situ material blending of a pelletized feedstock. Constructing MM and functionally graded material (FGM) structures requires depositing a specific material composition at a specific geometric location to achieve a desired performance. Furthermore, accurately implementing this with the BAAM’s blended extrusion system requires a thorough understanding of the transition between distinct material compositions. This study characterizes a step-change transition between neat acrylonitrile butadiene styrene (ABS) and carbon fiber-reinforced ABS. Three distinct techniques were compared for analyzing the fiber content, and the transition zone between materials was characterized as a function of transition direction. The transition process was consistent to within 0.7 wt% carbon fiber variation between different layers and prints. The transition between materials was found to be directionally dependent, with ABS to CF/ABS having a transition length of 3.5 m compared to 3.2 m for CF/ABS to ABS. Furthermore, the transition from Material A to Material B was found to be repeatable with a possible variance in transition length of 0.3 m.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Physical Properties of Moist, Fermented Corn Kernels

A novel approach to producing corn stover biomass feedstock has been investigated. In this approach, corn grain and stover are co-harvested at moisture contents much less than typical corn silage. The grain and stover are conserved together by anaerobic storage and fermentation and then separated before end use. When separated from the stover, the moist, fermented grain had physical characteristics that differ from typical low-moisture, unfermented grain. A comprehensive study was conducted to quantify the physical properties of this moist, fermented grain. Six corn kernel treatments, either fermented or unfermented, having different moisture contents, were used. Moist, fermented kernels (26 and 36% w.b. moisture content) increased in size during storage. The fermented kernels’ widths and thicknesses were 10% and 15% greater, respectively, and their volume was 28% greater than the dry kernels (15% w.b.). Dry basis particle density was 9% less for moist, fermented kernels. Additionally, the dry basis bulk density was 29% less, and the dry basis hopper-discharged mass flow rate was 36% less. Moist, fermented grain had significantly greater kernel-to-kernel coefficients of friction and angles of repose compared to relatively dry grain. The friction coefficient on four different surfaces was also significantly greater for fermented kernels. Fermented corn kernels had lower individual kernel rupture strengths than unfermented kernels. These physical differences must be considered when designing material handling and processing systems for moist, fermented corn grain.

09 BIOMASS FUELS↗
NASA NTRS2016

An Influenced Future

Phobos is a vital precursor and catalyst before our next giant leap to Mars. The principle period of a Phobos' mission could be a series of robotic precursor missions for experimental perception, soil examination, ecological approval and landing site distinguishing proof. For my summer intern position at Johnson Space Center I chipped away at creating a GUNNS (General Use Nodal Network Solver) based power subsystem model for the miniATHLETE hopper, which is a conceptual (idea-based) robotic lander that will operate on Phobos. Keeping in mind the end goal to begin on my venture, I needed to comprehend my undertaking before whatever else, in which I concentrated on C++ to see how to implement the code that GUNNS generates to a Trick S_define file. Prior to coming to this internship at Johnson Space Center Dr. Edwin Zack Crues provided a class on modeling and simulation, which introduced me to the Trick simulation environment. The goal of my project was to develop a GUNNS based power subsystem model for the miniATHLETE hopper. The model needed to incorporate a solar array, battery, hopping legs, and onboard scientific instruments (sensitive measuring/recording devices). The secondary bonus goal after I completed the electrical aspect of my model was to develop a GUNNS based thermal subsystem model for the miniATHLETE hopper. Stringing the two aspects together, I would need to code up a signal aspect to make the system work as one. Accomplishing my goals would not be an easy thing, however I had successfully completed the electrical aspect model with twenty-four servos, six cameras, and multiple sensors. Venturing to complete my project has eluded me to many failures in my design to tune many things like the battery to the proper voltage and the load to the proper wattage. During this time I had touched up on advanced topics in calculus in which I implemented in the converter in my electrical model. I am currently working with my mentor Zu Qun Li to create a signal aspect to control the temperatures inside my electrical aspect model. During my time at JSC I had effectively figured out how to create subsystem models utilizing Trick and GUNNS. I obtain essential knowledge of power and thermal subsystem design for a robotic vehicle. I also learned how to work and communicate in a team effectively to accomplish a goal. Before coming to Johnson Space Center my future career and educational goals included uncertainty, however now I have a completely new look on my path to a prosperous future. My NASA experience has unquestionably impacted me to accomplish and surpass my own particular desires. After my time at Johnson Space Center I plan to apply for a coop position for NASA. This has been a dream come true that I adored each moment being at JSC realizing that I am far fit for doing things most individuals can just long for.

Owens, Christopher↗
NASA NTRS2013

Demonstration of Critical Systems for Propellant Production on Mars for Science and Exploration Missions

A Mars hopper has been proposed as a Mars mobility concept that will also demonstrate and advance in-situ resource utilization. The components needed in a Mars propellant production plant have been developed to various levels of technology maturity, but there is little experience with the systems in a Mars environment. Two systems for the acquisition and compression of the thin carbon dioxide atmosphere were designed, assembled, and tested in a Mars environment chamber. A microchannel sorption pump system was able to raise the pressure from 7 Torr to 450 Torr or from 12 Torr to over 700 Torr in two stages. This data now provides information needed to make additional improvements in the sorption pump technology to increase performance, although a system-level analysis might prove that some amount of pre- or post-compression may be a preferred solution. A mini cryofreezer system was also evaluated as an alternative method for carbon dioxide acquisition and compression. Finally, an electrolysis system was tested and successfully demonstrated start-up operation and thermal stability of all components during long-term operation in the chamber.

Linne, Diane L.↗
NASA NTRS1978

The 30-cm ion thruster power processor

A power processor unit for powering and controlling the 30 cm Mercury Electron-Bombardment Ion Thruster was designed, fabricated, and tested. The unit uses a unique and highly efficient transistor bridge inverter power stage in its implementation. The system operated from a 200 to 400 V dc input power bus, provides 12 independently controllable and closely regulated dc power outputs, and has an overall power conditioning capacity of 3.5 kW. Protective circuitry was incorporated as an integral part of the design to assure failure-free operation during transient and steady-state load faults. The implemented unit demonstrated an electrical efficiency between 91.5 and 91.9 at its nominal rated load over the 200 to 400 V dc input bus range.

Herron, B. G.↗
DOE OSTI2021

Abrasion wear at high temperature in particle receiver type Concentrating Solar Power Systems

The use of solid particles as a heat transfer fluid in receivers for concentrating solar powerplants has garnered much attention in the past decade. Particles are not only stable at temperatures above 700 °C but are also able to absorb solar energy directly, which gives them a distinct advantage over conventional molten salts. The use of particles can, however, cause material degradation from the flow of hot or cold particles through discharge hoppers or along the inner receiver surfaces and other system components (e.g. tubes, valves etc.), depending on operating mode of the receiver. Stainless steel alloy 316, nickel-based alloy Inconel® 740H®, Haynes 230, and a 60% alumina, low-cement refractory castable from Allied Mineral Products were tested for wear from first-of-a-kind high-temperature low-velocity abrasion-erosion experiments. The tests are designed to simulate potential conditions in Generation 3 falling particle Concentrating Solar Power (CSP) systems. Simultaneous experiments were conducted at room temperature as well to draw comparison on the role of temperature on abrasion wear rates. It was noted that the abrasion wear rate in candidate materials was driven by the oxidation resistance of the material. The findings from these experiments will be used to determine life-time of critical components in particle receiver concentrated solar powerplants.

14 SOLAR ENERGY↗
DOE OSTI2021

Computational Fluid Dynamics Simulation of Compressible Non-Newtonian Biomass in a Compression-Screw Feeder

Compression-screw feeders play a critical role in biorefineries to transport lignocellulosic biomass feedstocks from the feeding hoppers to biomass-conversion reactors in order to pretreat and convert biomass to hydrocarbon liquid biofuels and other power and energy resources. One of the main challenges in the operation of screw feeder is plugging and jamming of compressed biomass with high concentration of insoluble solids. The focus of this paper is to numerically investigate the screw feeder at these challenging operating conditions and help with the optimization of the screw feeder design to avoid operation failure. In this work a customized CFD model based on open-source OpenFOAM package [1] was developed to simulate the concentrated biomass as a highly viscous non-Newtonian fluid in the screw feeder. The biomass is modeled as a single-phase compressible Bingham fluid with a plastic viscosity as well as a density-dependent yield stress. The compressibility formulation (pressure-dependent density) and the density-dependent yield stress formulation in the governing equations follow the suggestions from a recent study by Duncan et al. [2]. A pilot-scale hopper/screw feeding system at NREL [3] is used to compare the experimental observations with our simulation results. The auger is 280 mm long and tapered with outer diameter changing from 80 mm to 35 mm. The auger rotates from 10 to 60 rpm in a conical throat which contains anti-rotational bars. The simulations predicted the required torque for the screw feeder and the pressure increase at the exit for biomass feedstocks with various fluid viscosity properties and auger rotating speeds. The analysis of the stress forces helped to identify the critical conditions were the screw feeder excessive wear or jamming could occur.

biofuels↗
NASA NTRS1979

Lander flight path analysis

The primary functions of the Lander Flight Path Analysis Team (LFPAT) were to (1) design the Viking Lander (VL) descent trajectory and compute the descent guidance parameters for command transmission to the Viking Lander and Viking Orbiter (VO), (2) reconstruct the VL trajectory from separation to touchdown using data transmitted from the VL to Earth via the VO during descent, and (3) predict the VL/VO relay link system performance during descent and post touchdown. The preflight VL capability, the history of proposed descent trajectory designs as the site selection process evolved, and the final trajectory design and guidance parameters for each vehicle are addressed along with the trajectory reconstruction process, including the overall reconstructed VL flight path summary and a detailed discussion of the entry trajectory and atmosphere reconstruction results. The postland relay link prediction function is discussed.

Euler, E. A.↗
NASA NTRS2009

Study of Electro-Cyclonic Filtration and Pneumatic Transfer of Lunar Regolith Simulants under 1/6-g and 1-g Gravity Conditions

NASA has built a prototype oxygen production plant to process the lunar regolith using the hydrogen reduction chemical process. This plant is known as "ROxygen - making oxygen from moon rocks". The ROxygen regolith transfer team has identified the flow and transfer characteristics of lunar regolith simulant to be a concern for lunar oxygen production efforts. It is important to ISRU lunar exploration efforts to develop hardware designs that can demonstrate the ability to flow and transfer a given mass of regolith simulant to a desired vertical height under lunar gravity conditions in order to introduce it into a reactor. We will present results obtained under both 1/6-g and 1-g gravity conditions for a system that can pneumatically convey 16.5 kg of lunar regolith simulant (NU-LHT-2M, Mauna Kea Tephra, and JSC-1A) from a flat-bottom supply hopper to a simulated ISRU reactor (dual-chambered receiving hopper) where the granular material is separated from the convey gas (air) using a series of cyclone separators, one of which is an electrically enhanced cyclone separator (electrocyclone). The results of our study include (1) the mass flow rate as a function of input air pressure for lunar regolith simulants that are conveyed pneumatically as a dusty gas in a vertical direction against gravity under lunar gravity conditions (for NU-LHT-2M and Mauna Kea Tephra), and under earth gravity conditions (for NU-LHT-2M, Mauna Kea Tephra and JSC-1A), and (2) the efficiency of the cyclone/electrocyclone filtration system in separating the convey gas (air) from the granular particulates as a function of particle size.

Mantovani, James G.↗
DOE OSTI2022

On the Fidelity of Computational Models for the Flow of Milled Loblolly Pine: A Benchmark Study on Continuum-Mechanics Models and Discrete-Particle Models

The upstream of bioenergy industry has suffered from unreliable operations of granular biomass feedstocks in handling equipment. Computational modeling, including continuum-mechanics models and discrete-particle models, offers insightful understandings and predictive capabilities on the flow of milled biomass and can assist equipment design and optimization. This paper presents a benchmark study on the fidelity of the continuum and discrete modeling approaches for predicting granular biomass flow. We first introduce the constitutive law of the continuum-mechanics model and the contact law of the coarse-grained discrete-particle model, with model parameters calibrated against laboratory characterization tests of the milled loblolly pine. Three classical granular material flow systems (i.e., a lab-scale rotating drum, a pilot-scale hopper, and a full-scale inclined plane) are then simulated using the two models with the same initial and boundary conditions as the physical experiments. The close agreement of the numerical predictions with the experimental measurements on the hopper mass flow rate, the hopper critical outlet width, the material stopping thickness on the inclined plane, and the dynamic angle of repose, clearly indicates that the two methods can capture the critical flow behavior of granular biomass. The qualitative comparison shows that the continuum-mechanics model outperforms in parameterization of materials and wall friction, and large-scale systems, while the discrete-particle model is more preferred for discontinuous flow systems at smaller scales. Industry stakeholders can use these findings as guidance for choosing appropriate numerical tools to model biomass material flow in part of the optimization of material handling equipment in biorefineries.

Jin, Wencheng↗
NASA NTRS1977

The design and reconstruction of the Viking Lander descent trajectories

The success of the Viking Mission is truly a major milestone in this country's planetary exploration program. This paper deals with the trajectory characteristics of the Viking Lander descent trajectories, beginning with the imposed requirements and constraints, the final preflight design based on the final hardware and operational capability, and ending with the actual performance achieved. A comparison between the predicted and actual trajectory characteristics is made to indicate the achieved accuracy and modeling fidelity. Also, estimates of the Martian environment derived from the entry-trajectory reconstruction process are presented.

Euler, E. A.↗
NASA NTRS1971

A closely regulated TWT converter.

The design concept for the TWT amplifier converter for possible use in the Thermoelectric Outer Planet Spacecraft (TOPS) is presented. An unusual combination of semiconductors and magnetics was utilized to achieve very stable voltage regulation on a number of separate outputs to satisfy the requirements of a high-power TWT, and at the same time operate at an efficiency of better than 90% from a 30-V source. The circuitry consists of an output filter, an auxiliary Jensen oscillator driving a high-reactance transformer to provide current limiting to the heater, a variable time delay, a main Jensen oscillator driving the power transformer with a maximum step-up ratio of 120 to 1, and series transistorized post regulators to provide precise voltage adjustment and low output impedance. This paper discusses the design of the high-reactance transformer and the high step-up ratio transformer, as well as the high-voltage series regulators that are limited in range and operate at the top of the unregulated output voltage. Test data are presented, and details of current transients caused by charging the filter circuits, input current ripple, and output voltage ripples are considered.

Hopper, D. J.↗
DOE OSTI2020

Radioactive Cleaning Robot

Here at Fermi National Accelerator Laboratory, particle accelerators are constantly running, giving off excess radioactive dust. This dust can be extremely harmful to people and the environment, posing numerous issues. The goal of this project is to conceptualize an automated cleaning solution. With this main goal in mind, the project started with a brainstorming session. The main concept relied on the use of a powder distributing system paired with a vacuum to easily attract and trap the dust. From this main concept, multiple sketches were produced, showing a robot with pieced-together systems. With the initial idea down, each subsystem could be brought further with the inner workings being sketched out. After sketches and proof of concept were polished, the next step was to begin 3D modeling, using NX, to bring life into the sketches. With every day came new ideas, modifying the previous sketches and models as necessary. Soon after the bigger structures were fleshed out, the focus could be shifted onto the less pressing subsystems. Adding a conveyor belt and spinning brush attachment to the powder hopper allowed for more even powder distribution. Along with that, the addition of spring-loaded brushes on the vacuum nozzle ensures constant dust agitation, improving overall functionality. A few other quality of life improvements, such as a removable dust reservoir with a ramp gave a push towards real life functionality. After considering the logistics of this robot functioning in real-life, pressure plates were provided to stop the robot from crashing into its surroundings. Having all of the individual models lead to an overall assembly. Making this robot programmable allowed for this project to meet the design requirements, providing a solution to the previous dilemma.

43 PARTICLE ACCELERATORS↗
NASA NTRS2013

NASA Tech Briefs, May 2013

Topics include: Test Waveform Applications for JPL STRS Operating Environment; Pneumatic Proboscis Heat-Flow Probe; Method to Measure Total Noise Temperature of a Wireless Receiver During Operation; Cursor Control Device Test Battery; Functional Near-Infrared Spectroscopy Signals Measure Neuronal Activity in the Cortex; ESD Test Apparatus for Soldering Irons; FPGA-Based X-Ray Detection and Measurement for an X-Ray Polarimeter; Sequential Probability Ratio Test for Spacecraft Collision Avoidance Maneuver Decisions; Silicon/Carbon Nanotube Photocathode for Splitting Water; Advanced Materials and Fabrication Techniques for the Orion Attitude Control Motor; Flight Hardware Packaging Design for Stringent EMC Radiated Emission Requirements; RF Reference Switch for Spaceflight Radiometer Calibration; An Offload NIC for NASA, NLR, and Grid Computing; Multi-Scale CNT-Based Reinforcing Polymer Matrix Composites for Lightweight Structures; Ceramic Adhesive and Methods for On-Orbit Repair of Re-Entry Vehicles; Self-Healing Nanocomposites for Reusable Composite Cryotanks; Pt-Ni and Pt-Co Catalyst Synthesis Route for Fuel Cell Applications; Aerogel-Based Multilayer Insulation with Micrometeoroid Protection; Manufacturing of Nanocomposite Carbon Fibers and Composite Cylinders; Optimized Radiator Geometries for Hot Lunar Thermal Environments; A Mission Concept: Re-Entry Hopper-Aero-Space-Craft System on-Mars (REARM-Mars); New Class of Flow Batteries for Terrestrial and Aerospace Energy Storage Applications; Reliability of CCGA 1152 and CCGA 1272 Interconnect Packages for Extreme Thermal Environments; Using a Blender to Assess the Microbial Density of Encapsulated Organisms; Mixed Integer Programming and Heuristic Scheduling for Space Communication; Video Altimeter and Obstruction Detector for an Aircraft; Control Software for Piezo Stepping Actuators; Galactic Cosmic Ray Event-Based Risk Model (GERM) Code; Sasquatch Footprint Tool; and Multi-User Space Link Extension (SLE) System.

Source record↗