Search NASA⌕ Search

SEARCH · Search NASA

Results for “improved microstructures and properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Effect of Excess Lead and Bismuth Content on the Electrical Properties of High-Temperature Bismuth Scandium Lead Titanate Ceramics

Aeronautic and aerospace applications require piezoelectric materials that can operate at high temperatures. The air-breathing aeronautic engines can use piezoelectric actuators for active combustion control for fuel modulation to mitigate thermo-acoustic instabilities and/or gas flow control to improve efficiency. The principal challenge for the insertion of piezoelectric materials is their limitation for upper use temperature and this limitation is due low Curie temperature and increasing conductivity. We investigated processing, microstructure and property relationship of (1-x)BiScO3-(x)PbTiO3 (BS-PT) composition as a promising high temperature piezoelectric. The effect of excess Pb and Bi and their partitioning in grain boundaries were studied using impedance spectroscopy, ferroelectric, and piezoelectric measurement techniques. Excess Pb addition increased the grain boundary conduction and the grain boundary area (average grain size was 24.8 m, and 1.3 m for compositions with 0at.% and 5at.% excess Pb, respectively) resulting in ceramics with higher AC conductivity (tan d= 0.9 and 1.7 for 0at.% and 5at.% excess Pb at 350 C and at 10kHz) that were not resistive enough to pole. Excess Bi addition increased the resistivity (rho= 4.1x10(exp 10) Omega cm and 19.6 x10(exp 10) Omega.cm for compositions with 0at.% and 5at.% excess Bi, respectively), improved poling, and increased the piezoelectric coefficient from 137 to 197 pC/N for 5at.% excess Bi addition. In addition, loss tangent decreased more than one order of magnitude at elevated temperatures (greater than 300 C). For all compositions the activation energy of the conducting species was similar (approximately equal to 0.35-0.40 eV) and indicated electronic conduction.

Sehirlioglu, Alp↗

Electron Beam Freeform Fabrication of Titanium Alloy Gradient Structures

Historically, the structural optimization of aerospace components has been done through geometric methods. A monolithic material is chosen based on the best compromise between the competing design limiting criteria. Then the structure is geometrically optimized to give the best overall performance using the single material chosen. Functionally graded materials offer the potential to further improve structural efficiency by allowing the material composition and/or microstructural features to spatially vary within a single structure. Thus, local properties could be tailored to the local design limiting criteria. Additive manufacturing techniques enable the fabrication of such graded materials and structures. This paper presents the results of a graded material study using two titanium alloys processed using electron beam freeform fabrication, an additive manufacturing process. The results show that the two alloys uniformly mix at various ratios and the resultant static tensile properties of the mixed alloys behave according to rule-of-mixtures. Additionally, the crack growth behavior across an abrupt change from one alloy to the other shows no discontinuity and the crack smoothly transitions from one crack growth regime into another.

Brice, Craig A.↗

Recent Advances in Structural Carbon Nanotube Composites

Carbon nanotubes (CNT) have been a subject of investigation for more than two decades. Part of the interest in CNTs was driven by CNT tensile mechanical properties at the nanoscale that suggest their potential to outperform state-of-the-art (SOA) lightweight structural materials. Early work on the development of CNT nanocomposites involved the dispersion of CNT powder into polymer matrices. Although low levels of CNT doping resulted in meaningful increases in electrical conductivity to enable applications such as electrostatic charge dissipation, the highest concentrations of CNTs in these lightly doped nanocomposites did not yield mechanical properties that could compete with SOA carbon fiber composites. The maximum concentration of CNTs in lightly doped nanocomposites was limited to about 5% due to increases in viscosity that prevent the fabrication of good quality nanocomposites. At the lower concentrations, properties of the resulting nanocomposites were analogous to those of composites made with very short, chopped carbon fibers. About ten years ago, CNTs became available in continuous fiber form, allowing the investigation of processing methods to incorporate much higher CNT content into composites. Recent developments in CNT composite fabrication have yielded improved mechanical properties and indicate that while some standard carbon fiber composite processing methods can be used, CNTs have unique microstructural features that require techniques tailored to access the hierarchical features of CNTs. This presentation will discuss the evolution of structural CNT mechanical property advancements and collaboration mechanisms for research across federal labs, academia, and industry that accelerated the maturation of structural CNTs.

Carbon Nanotubes↗

Convolution-Based Numerical Solutions of Transient Temperature Fields during Powder Bed Fusion Additive Manufacturing: Theory, Accuracy, and Computational Cost

Powder bed fusion (PBF) additive manufacturing has found numerous applications in the aerospace domain. However, components fabricated via PBF have a complex time-temperature history that significantly impacts subsequent mechanical performance. This study examines convolution-based numerical solutions of transient temperature fields that support simulations involving arbitrary beam shapes and paths during PBF. The convolutional approach is verified through comparisons with analytical solutions of the temperature field. The computational speed and accuracy of the method are assessed through comparisons with other explicit and implicit numerical techniques. In addition, the straightforward translation of the approach from a CPU to a GPU implementation and the resultant performance improvement are presented. The role of the technique in predicting microstructure evolution during PBF (for a greater process-structure-property-performance framework) is also demonstrated. This work supports the development of computational materials methods for understanding and controlling the time-temperature history during PBF.

powder bed fusion↗

Investigation of Advanced Processed Single-Crystal Turbine Blade Alloys

This investigation studied the influence of thermal processing and microstructure on the mechanical properties of the single-crystal, nickel-based superalloys PWA 1482 and PWA 1484. The objective of the program was to develop an improved single-crystal turbine blade alloy that is specifically tailored for use in hydrogen fueled rocket engine turbopumps. High-gradient casting, hot isostatic pressing (HIP), and alternate heat treatment (HT) processing parameters were developed to produce pore-free, eutectic-free microstructures with different (gamma)' precipitate morphologies. Test materials were cast in high thermal gradient solidification (greater than 30 C/cm (137 F/in.)) casting furnaces for reduced dendrite arm spacing, improved chemical homogeneity, and reduced interdendritic pore size. The HIP processing was conducted in 40 cm (15.7 in.) diameter production furnaces using a set of parameters selected from a trial matrix study. Metallography was conducted on test samples taken from each respective trial run to characterize the as-HIP microstructure. Post-HIP alternate HT processes were developed for each of the two alloys. The goal of the alternate HT processing was to fully solution the eutectic gamma/(gamma)' phase islands and to develop a series of modified (gamma)' morphologies for subsequent characterization testing. This was accomplished by slow cooling through the (gamma)' solvus at controlled rates to precipitate volume fractions of large (gamma)'. Post-solution alternate HT parameters were established for each alloy providing additional volume fractions of finer precipitates. Screening tests included tensile, high-cycle fatigue (HCF), smooth and notched low-cycle fatigue (LCF), creep, and fatigue crack growth evaluations performed in air and high pressure (34.5 MPa (5 ksi)) hydrogen at room and elevated temperature. Under the most severe embrittling conditions (HCF and smooth and notched LCF in 34.5 MPa (5 ksi) hydrogen at 20 C (68 F), screening test results showed increases in fatigue life typically on the order of 1OX, when compared to the current Space Shuttle Main Engine (SSME) Alternate Turbopump (AT) blade alloy (PWA 1480).

Peters, B. J.↗

Optimization of Hot-Pressed n-Type SiGe/GaP and p-Type SiGe/B Thermoelectric Materials

A comprehensive experimental and theoretical work has been conducted in order to optimize the thermoelectric properties of Si_(80)Ge_(20) materials and reach the goal of a combined figure of merit value of 0.85x10^(-3) K^(-1) averaged over a 600-1000 C temperature range. Improvement for the n-type material has been obtained by determining the optimum amounts of gallium and phosphorus dopants necessary to achieve optimum carrier mobility and concentration. The emphasis is now on the consistent reproducibility of these results through understanding and control of the hot-pressing parameters relating microstructure and composition to the transport properties. The optimum doping level has now been firmly established for p-type materials, and work is concentrating on the reduction in thermal conductivity. BN ultra fine particles have been successfully incorporated into fully dense samples and have resulted in desired improvement of the figure of merit...

Fleurial, Jean-Pierre↗

High-temperature ordered intermetallic alloys III; Proceedings of the Third Symposium, Boston, MA, Nov. 29-Dec. 1, 1988

The present conference on high-temperature ordered intermetallic alloys discusses alloy theory and phase stability, defects and microstructures, mechanical behavior, alloy design and material processing, multiphase and composite materials, nickel aluminides, titanium aluminides, and other ordered intermetallics. Attention is given to compositional effects on processing and properties of nickel aluminides, dynamic compaction and hot-isostatic-pressing of nickel aluminides, improvement of elevated-temperature material properties in Ni3Al, the effect of microalloying B on the high-temperature mechanical properties of Ti3Al, the effects of structure on creep of Ti-53.4 mol pct Al intermetallics, the deformation microstructure in Ni3Si polycrystals strained over the range of temperature of flow stress anomaly, and the microstructure and mechanical properties of dual phase alloys consisting of the intermetallic phases.

Liu, C. T.↗

Effect of high-temperature annealing on the microstructure and thermoelectric properties of GaP doped SiGe

Annealing of GaP doped SiGe will significantly alter the thermoelectric properties of the material resulting in increased performance as measured by the figure of merit Z and the power factor P. The microstructures and corresponding thermoelectric properties after annealing in the 1100 to 1300 C temperature range have been examined to correlate performance improvement with annealing history. The figure of merit and power factor were both improved by homogenizing the material and limiting the amount of cross-doping. Annealing at 1215 C for 100 hr resulted in the best combination of thermoelectric properties with a resultant figure of merit exceeding 1x10 to the -3 deg C to the -1 and a power factor of 44 microW/cm/deg C sq for the temperature range of interest for space power: 400 to 1000 C.

Draper, Susan L.↗

The importance of properties in modeling

Casting and welding of superalloys, stainless steel and titanium alloys are processes which can be improved through modeling of heat flow, fluid flow, residual stress development, and microstructural evolution. These simulations require inputs of thermophysical data, some of which involves the partially or totally liquid state. In particular, these processes involve melting, flow in the liquid, and solidification. Modeling of such processes can lead to an improved understanding of defects such as shrinkage, inclusions, cracks, incomplete filling (or penetration), macrosegregation, improper grain structure, and deviations from dimensional specifications. Effective modeling can shorten process development time and improve quality. An approach to these problems is to develop efficient models; validate through correlations with thermal, distortion, and microstructural data; run parametric studies; extract knowledge based rules; and apply to adaptive closed loop control systems. With the appropriate pre- and post-processing, such analyses can be made 'user friendly'. This would include graphical user interfaces as well as realistic images and color maps. In such form, these models can be used for sensitivity analyses, which are useful in defining appropriate sensors and in the development of control strategies. Such modeling can be done at several levels, e.g., the MARO level, modeling large scale phenomena such as heat and fluid flow or material deformation; the MICRO level, modeling the development of dendrites, grains or precipitates; or at the NANO level, modeling point defects, dislocations, stacking faults, etc. There are many computational issues associated with these simulations, e.g. computational efficiency and accuracy. In addition, there are many materials issues, not the least of which is the availability of accurate high temperature thermophysical data for complex alloys. This would include latent heat of fusion, temperature dependent heat capacity and thermal conductivity (for liquid and solid), viscosity, surface tension, thermal expansion, mechanical properties, etc. Preliminary data is frequently gathered from the literature; however, this is often not available for modern alloys. If additional data are required, measurements can be used; however, these are costly, time consuming and can be erroneous due to a lack of testing standards or impure materials. Microstructural predictors can be extracted from thermal information, e.g. cooling rate and thermal gradient; the prediction of microstructure is dependent on solidus and liquidus temperature, mushy zone permeability, the solidification curve, volume changes, phase transformations, alloying effects (such as surface tension or viscosity), mold/metal reactions, metal/environment reactions, etc. Defect maps may be needed to predict the onset of shrinkage, hot cracking or 'freckling'. Constants may be needed for stress relaxation, dendrite coarsening, vaporization, etc. Visualization was used as a tool to better comprehend complex data sets associated with the analysis of directional solidification (including crystal growth) and welding. Examples include not only isotherms, but also cooling rate, growth rate and thermal gradient. The latter two are not single valued scalars, but rather time and space dependent vector fields. Efficient models were developed for both casting and welding to predict heat flow and the relationship to dendrite and grain growth. These codes include many of the non-linear effects, e.g. radiation, which dominate these processes. The home-built FDM code(s) were designed to be useful not only to the scientist, but also to the process engineer. Special output can be requested to compare directly to experimental data. Visualization procedures were developed to visualize critical results, e.g. fusion zone width at the surface opposite that where the arc is applied ('penetration'). Both elaborate and simplified distortion analyses were carried out. It is clear that extensive mechanical property data are critical in order to accurately predict residual stress patterns. A scheme is currently being developed to integrate these modeling tools into a set of control algorithms; however, the success of this approach is critically dependent on the availability of accurate high temperature thermophysical data.

Giamei, A. F.↗

Extreme Temperature Additively Manufactured GRX-810 Alloy Development and Hot-fire Testing for Liquid Rocket Engines

Additive manufacturing (AM) has revolutionized component design for liquid rocket engines by offering rapid manufacturing capabilities. This has led to significant opportunities for development and flight programs in the propulsion industry, resulting in cost and schedule savings, as well as performance improvements through new designs and alloy development. A noteworthy example is the GRX-810 oxide dispersion strengthened (ODS) alloy, which was specifically developed for extreme temperatures. This Ni-Co-Cr based alloy was created using integrated computational materials engineering (ICME) techniques to focus on a new class of materials with exceptional temperature and oxidation-resistant properties. The GRX-810 alloy utilizes AM processes to incorporate nano-scale yttria particles throughout its microstructure, resulting in remarkable enhancements. Compared to traditional Nickel-based superalloys, the GRX-810 alloy offers a two-fold increase in tensile strength, 1,000-fold better creep properties, and two-fold improvement in oxidation resistance. NASA successfully demonstrated the development and manufacturing of components using the GRX-810 alloy through laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. Extensive efforts were made to model, evaluate metallurgical properties, develop heat treatment processes, characterize the microstructure, and determine mechanical properties. The GRX-810 alloy was specifically designed for aerospace applications, including liquid rocket engine injectors, preburners, turbines, and hot-section components, capable of withstanding temperatures up to 1,100 °C. The objective of this alloy development is to bridge the temperature gap between traditional Nickel-based superalloys and refractory alloys. This paper provides a comprehensive comparison of the GRX-810 alloy with other aerospace alloys, discussing its microstructure, mechanical properties, processing advancements, component development, and hot-fire testing results. The ultimate goal of this development was to elevate the Technology Readiness Level (TRL) of the GRX-810 alloy, enabling its integration into NASA and commercial aerospace applications.

GRX-810↗

Extreme Temperature Additively Manufactured GRX-810 Alloy Development and Hot-fire Testing for Liquid Rocket Engines

Additive manufacturing (AM) has revolutionized component design for liquid rocket engines by offering rapid manufacturing capabilities. This has led to significant opportunities for development and flight programs in the propulsion industry, resulting in cost and schedule savings, as well as performance improvements through new designs and alloy development. A noteworthy example is the GRX-810 oxide dispersion strengthened (ODS) alloy, which was specifically developed for extreme temperatures. This Ni-Co-Cr based alloy was created using integrated computational materials engineering (ICME) techniques to focus on a new class of materials with exceptional temperature and oxidation-resistant properties. The GRX-810 alloy utilizes AM processes to incorporate nano-scale yttria particles throughout its microstructure, resulting in remarkable enhancements. Compared to traditional Nickel-based superalloys, the GRX-810 alloy offers a two-fold increase in tensile strength, 1,000-fold better creep properties, and two-fold improvement in oxidation resistance. NASA successfully demonstrated the development and manufacturing of components using the GRX-810 alloy through laser powder bed fusion (L-PBF) and laser powder directed energy deposition (LP-DED) processes. Extensive efforts were made to model, evaluate metallurgical properties, develop heat treatment processes, characterize the microstructure, and determine mechanical properties. The GRX-810 alloy was specifically designed for aerospace applications, including liquid rocket engine injectors, preburners, turbines, and hot-section components, capable of withstanding temperatures up to 1,100 °C. The objective of this alloy development is to bridge the temperature gap between traditional Nickel-based superalloys and refractory alloys. This paper provides a comprehensive comparison of the GRX-810 alloy with other aerospace alloys, discussing its microstructure, mechanical properties, processing advancements, component development, and hot-fire testing results. The ultimate goal of this development was to elevate the Technology Readiness Level (TRL) of the GRX-810 alloy, enabling its integration into NASA and commercial aerospace applications.

GRX-810↗

Short-Term Elevated Temperature Mechanical Performance and Microstructure of A Niobium-Zirconium Alloy Produced via Laser Powder Bed Fusion In-Situ Alloying

Nb-1Zr is a readily fabricable, dispersion-strengthened niobium alloy with improved elevated temperature properties compared to commercially pure niobium. This low to moderate strength niobium alloy is desirable in thermal management systems for fission power and propulsion applications; however, pre-alloyed spherical feedstock for powder-based additive manufacturing processes is generally unavailable. Laser powder bed fusion (L-PBF) in-situ alloying of a Nb-1Zr chemistry was performed using a high-purity niobium feedstock coated with 1 wt% of zirconium-based ceramic compound nano-powders: ZrO 2 , ZrC, and ZrH 2 . The additively manufactured material was mechanically tested at elevated temperatures within a controlled environment in the as-built condition. For comparison, traditionally manufactured wrought feedstock was also tested within an identical environment. Examination of the materials’ microstructure and short-term elevated temperature mechanical response determined: in-situ alloying of spherical Nb powder feedstock with Zr-based ceramic nanoparticles can be successfully implemented; the ZrO 2 addition offered the greatest elevated temperature stability and strength but exhibited brittle behavior; the ZrC addition achieved a balance of room temperature ductility and elevated temperature strength; and the ZrH 2 -modified material had the lowest as-built interstitial content and showed high ductility with mechanical performance most similar to wrought Nb-1Zr.

Niobium Alloy↗

Ultrasonic Guided-Wave Scan System Used to Characterize Microstructure and Defects in Ceramic Composites

Ceramic matrix composites (CMCs) are being developed for advanced aerospace propulsion applications to save weight, improve reuse capability, and increase performance. However, mechanical and environmental loads applied to CMCs can cause discrete flaws and distributed microdamage, significantly reducing desirable physical properties. Such microdamage includes fiber/matrix debonding (interface failure), matrix microcracking, fiber fracture and buckling, oxidation, and second phase formation. A recent study (ref. 1) of the durability of a C/SiC CMC discussed the requirement for improved nondestructive evaluation (NDE) methods for monitoring degradation in these materials. Distributed microdamage in CMCs has proven difficult to characterize nondestructively because of the complex microstructure and macrostructure of these materials. This year, an ultrasonic guided-wave scan system developed at the NASA Glenn Research Center was used to characterize various microstructural and flaw conditions in SiC/SiC (silicon carbide fiber in silicon carbide matrix) and C/SiC (carbon fiber in silicon carbide matrix) CMC samples.

Roth, Don J.↗

PSIDD (2): A Prototype Post-Scan Interactive Data Display System for Detailed Analysis of Ultrasonic Scans

This article presents the description of PSIDD(2), a post-scan interactive data display system for ultrasonic contact scan and single measurement analysis. PSIDD(2) was developed in conjunction with ASTM standards for ultrasonic velocity and attenuation coefficient contact measurements. This system has been upgraded from its original version PSIDD(1) and improvements are described in this article. PSIDD(2) implements a comparison mode where the display of time domain waveforms and ultrasonic properties versus frequency can be shown for up to five scan points on one plot. This allows the rapid contrasting of sample areas exhibiting different ultrasonic properties as initially indicated by the ultrasonic contact scan image. This improvement plus additional features to be described in the article greatly facilitate material microstructural appraisal.

Cao, Wei↗

Creep Resistance of Disk Alloy CH98 with Tungsten and Niobium Additions

Gas turbine engines for future subsonic transports will likely have higher pressure ratios which will require nickel-base superalloy disks with temperature capability up to 1400 F, an increase of about 200 F over current engines. Several advanced disk alloys are being developed to fill this need. One of these, CH98, is a promising candidate for gas turbine engines and is being studied in NASA's AST Program. Additions of the refractory elements tungsten and niobium have been shown to improve tensile and creep properties while maintaining good high temperature fatigue crack growth resistance. Further improvements in creep and crack growth resistance can be achieved with a coarse grain microstructure. The purpose of the present study is aimed at providing a detailed assessment of 0.2 percent creep rates for coarse grain CH98 with tungsten and niobium additions over a range of temperatures and stresses of interest to disk applications.

Gayda, John↗

CEMCAN Software Enhanced for Predicting the Properties of Woven Ceramic Matrix Composites

Major advancements are needed in current high-temperature materials to meet the requirements of future space and aeropropulsion structural components. Ceramic matrix composites (CMC's) are one class of materials that are being evaluated as candidate materials for many high-temperature applications. Past efforts to improve the performance of CMC's focused primarily on improving the properties of the fiber, interfacial coatings, and matrix constituents as individual phases. Design and analysis tools must take into consideration the complex geometries, microstructures, and fabrication processes involved in these composites and must allow the composite properties to be tailored for optimum performance. Major accomplishments during the past year include the development and inclusion of woven CMC micromechanics methodology into the CEMCAN (Ceramic Matrix Composites Analyzer) computer code. The code enables one to calibrate a consistent set of constituent properties as a function of temperature with the aid of experimentally measured data.

Murthy, Pappu L. N.↗

Effects of Minor Alloying Additions on the Microstructure, Toughness, and Creep Strength of Directionally Solidified NiAl-31Cr-3Mo

A study of the effects of small (0.25 to 1.0 at%) fifth element additions to the structure and mechanical properties of directionally solidified (DS) NiAl-31Cr-3Mo has been undertaken. Essentially all the additions changed the as-DS'ed microstructure from lamellar eutectic grains to cells and, in some cases, introduced NiAl dendrites and/or third phases. In general the alloying additions did not improve strength or toughness over that possessed by the base composition; only Hf and, perhaps Ti, gave a minor increase in elevated temperature creep resistance. The lack of improvement in creep properties is probably due to inability to precipitation harden NiAl.

Whittenberger, J. D.↗