Search NASA⌕ Search

SEARCH · Search NASA

Results for “ink formulation and processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

On the direct ink write (DIW) 3D printing of styrene-butadiene rubber (SBR)-based adhesive sealant

Direct Ink Writing (DIW) utilizes a wide range of ink formulations to produce desirable 3D-printed structures and properties. Styrene-butadiene rubber (SBR) is an attractive candidate for 3D printing owing to its commercial availability, rheology, excellent mechanical properties, good impact resilience, and chemical stability. The SBR-based sealant was 3D printed in a DIW process, even in an ambient environment. The rheological behavior was assessed and correlated with optimized printing parameters. Important physico-chemical properties of the 3D-printed material were reported showing excellent properties as an elastomer. Finally, this work should expand the potential applications of existing rubber-based materials in additive manufacturing.

36 MATERIALS SCIENCE↗
NASA NTRS1983

Development of aircraft lavatory compartments with improved fire resistance characteristics. Phase 4: Sandwich panel decorative ink development

Five chemically different resin systems with improved fire resistance properties were studied for a possible screenprinting ink application. Fire resistance is hereby defined as the cured ink possessing improvements in flammability, smoke emission, and thermal stability. The developed ink is for application to polyvinyl fluoride film. Only clear inks without pigments were considered. Five formulations were evaluated compared with KC4900 clear acrylic ink, which was used as a baseline. The tests used in the screening evaluation included viscosity, smoke and toxic gas emission, limiting oxygen index (LOI), and polyvinyl fluoride film (PVF) printability. A chlorofluorocarbon resin (FPC461) was selected for optimization studies. The parameters for optimization included screenprinting process performance, quality of coating, and flammability of screenprinted 0.051-mm (0.002-in.) white Tedlar. The quality of the screenprinted coating on Tedlar is dependent on viscosity, curing time, adhesion to polyvinyl fluoride film, drying time (both inscreen and as an applied film), and silk screen mesh material and porosity.

Jayarajan, A.↗
DOE OSTI2026

Scalable Upcycling of Spent Lithium-Ion Battery Anodic Graphite to Electronic-Grade Graphene

Recycling processes for lithium-ion batteries (LIBs) are imperative to support the sustainable growth of global energy storage systems. This study introduces a scalable method for the upcycling of spent graphite anodes from LIBs to produce electronic-grade graphene nanoplatelets. In addition to comprehensive materials characterization, the electronic quality of the upcycled graphene is demonstrated by formulating it into a screen printing ink that achieves high-resolution patterning and thin-film electrical conductivity exceeding 104 S m−1. This screen printing ink is also used to print planar micro-supercapacitors with exceptional areal capacitance (1.78 mF cm−2), areal energy density (0.247 µWh cm−2), and cycling stability (> 10 000 cycles). Life cycle assessment (LCA) and techno-economic analysis (TEA) highlight the environmental benefits and cost reductions attainable through upcycling of graphite from LIBs. By capturing economic value from spent LIBs, this work fosters a sustainable battery supply chain and provides an abundant and geographically distributed raw material for electronic-grade graphene.

energy storage↗
DOE OSTI2026

Molecular Mechanisms Underlying Surfactant-Based Plastics De-Inking

Surfactant-mediated binder removal is critical for de-inking pretreatment in plastics recycling, yet the molecular mechanisms governing surfactant performance remain poorly understood. We used all-atom (AA) and coarse-grained (CG) molecular dynamics (MD) simulations alongside alkaline surfactant washing experiments to investigate interactions between a series of surfactants and a polyether urethane (PEU) binder in solution and on a polyethylene (PE) surface. Experiments reveal a range of de-inking efficiencies, ranging from <25 to >95% depending upon surfactant headgroup charge and tail length. AA simulations reveal that charged surfactants reach stable levels of surfactant coverage, while nonionic surfactants aggregate on the binder. CG umbrella sampling calculations quantify the thermodynamics of binder desorption in water. In ∼0.25 M surfactant solutions, up to a 52% reduction in the free energy barrier is computed, with trends in good agreement (R 2 = 0.92, Pearson’s r = –0.96, Spearman’s ρ = –0.83) with experimental de-inking efficiencies. We find that charged surfactants are more effective than nonionic surfactants for de-inking and propose three regimes of surfactant de-inking processes: good de-inking occurs in surfactants that promote PEU desorption with a low radius of gyration (R g ); moderate de-inking occurs when surfactants stabilize PEU but increase R g ; poor de-inking occurs in surfactants that aggregate on the binder and promote extensive anchoring to the surface. Overall, these molecular-level insights have the potential to guide the design of surfactant formulations for plastics recycling applications.

ink removal↗
NASA NTRS2006

Automated Solvent Seaming of Large Polyimide Membranes

A solvent-based welding process enables the joining of precise, cast polyimide membranes at their edges to form larger precise membranes. The process creates a homogeneous, optical-quality seam between abutting membranes, with no overlap and with only a very localized area of figure disturbance. The seam retains 90 percent of the strength of the parent material. The process was developed for original use in the fabrication of wide-aperture membrane optics, with areal densities of less than 1 kg/m2, for lightweight telescopes, solar concentrators, antennas, and the like to be deployed in outer space. The process is just as well applicable to the fabrication of large precise polyimide membranes for flat or inflatable solar concentrators and antenna reflectors for terrestrial applications. The process is applicable to cast membranes made of CP1 (or equivalent) polyimide. The process begins with the precise fitting together and fixturing of two membrane segments. The seam is formed by applying a metered amount of a doped solution of the same polyimide along the abutting edges of the membrane segments. After the solution has been applied, the fixtured films are allowed to dry and are then cured by convective heating. The weld material is the same as the parent material, so that what is formed is a homogeneous, strong joint that is almost indistinguishable from the parent material. The success of the process is highly dependent on formulation of the seaming solution from the correct proportion of the polyimide in a suitable solvent. In addition, the formation of reliable seams depends on the deposition of a precise amount of the seaming solution along the seam line. To ensure the required precision, deposition is performed by use of an automated apparatus comprising a modified commercially available, large-format, ink-jet print head on an automated positioning table. The printing head jets the seaming solution into the seam area at a rate controlled in coordination with the movement of the positioning table.

Rood, Robert↗
DOE OSTI2020

Influence of Coating Method on the Performance of Roll-to-Roll Coated PEM Fuel Cell Catalyst Layers

As production of fuel cell vehicles and power systems increases there is a need to understand the process science of fuel cell manufacturing. Industrial production of polymer electrolyte membrane fuel cell (PEMFC) electrodes will rely on continuous roll-to-roll (R2R) coating methods to meet the rates needed for mass production. There are a variety of coating methods that could be used to coat catalyst layers. The different physics of each method may result in different morphologies and performance. Here we present the results of a study comparing fuel cell catalyst layers coated using two R2R coating methods: slot-die and gravure. These two methods were selected because the physics of applying the liquid to the substrate is very different between the two cases. Pt/C catalysts layers were coated directly onto carbon-fiber gas diffusion media to create gas diffusion electrodes (GDEs), without the use of a decal transfer process. These GDEs were assembled into membrane electrode assemblies (MEAs) by hot pressing to Nafion membranes. In situ performance and other electrochemical diagnostics were used to determine the influence of coating method on catalyst layer electrochemical properties. Electron microscopy was utilized to understand the influence of coating method on electrode morphology and its influence on electrochemical properties. We also explored the influence of solvent ratio to understand the potential coupling between ink formulation and coating methodology.

DIRECT ENERGY CONVERSION,MATERIALS SCIENCE↗
DOE OSTI2019

3D Printing Catalytic Electrodes for Solar-Hydrogen Devices

Hydrogen production through water-splitting systems showed promising pathway to achieve <$2/kg cost target set by Department of Energy (DOE). As far, most efforts have been devoted to new electrocatalytical materials discovery. In contrast, the impact of architecture of the electrocatalysts as well as mass transport within the gas diffusion layers has not been well explored. In this project, we developed a new ink formulation with earth-abundant elements nickel and molybdenum (NiMo) for catalytical 3-dimentional (3D) electrodes in water-splitting devices. The NiMo electrodes fabricated via additive manufacturing have been characterized and tested. The architecture, morphology and compositions of the NiMo electrodes have been confirmed by Scanning Electric Microscopy (SEM) and Powder X-Ray Diffraction (XRD). We have demonstrated that the catalyst precursor survived the whole fabrication and post-treatment process. Furthermore, the NiMo 3D electrodes in this study exhibited state-of-art hydrogen evolution reaction (HER) performance, ~ 60 mV over potential for over 24 hours operation. The high performance of the 3D catalytical electrodes is attributed to large roughness factors (RF) of the electrodes and highly efficient mass transport. This study is in line with DOE initiative H2@Scale and national energy security missions at LLNL.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Effects of Ink Formulation on Construction of Catalyst Layers for High-Performance Polymer Electrolyte Membrane Fuel Cells

Rational design of catalyst layers in a membrane electrode assembly (MEA) is crucial for achieving high-performance polymer electrolyte membrane fuel cells. Establishing a clear understanding of the property (catalyst ink)–structure (catalyst layer)–performance (MEA) relationship lays the foundation for this rational design. Here, a synergistic approach was taken to correlate the ink formulation, the microstructure of catalyst layers, and the resulting MEA performance to establish such a property–structure–performance relationship. The solvent composition (n-PA/H 2 O mixtures) demonstrated a strong influence on the performance of the MEA fabricated with an 830-EW (Aquivion) ionomer, especially polarization losses of cell activation and mass transport. The performance differences were studied in terms of how the solvent composition affects the catalyst/ionomer interface, ionomer network, and pore structure of the resulting catalyst layers. The ionomer aggregates mainly covered the surface of catalyst aggregates acting as oxygen reduction reaction active sites, and the aggregate sizes of the ionomer and catalyst (revealed by ultrasmall angle X-ray scattering and cryo-transmission electron microscopy) were dictated by tuning the solvent composition, which in turn determined the catalyst/ionomer interface (available active sites). In n-PA/H 2 O mixtures with 50~90 wt % H 2 O, the catalyst agglomerates could be effectively broken up into small aggregates, leading to enhanced kinetic activities. The boiling point of the mixed solvents determined the pore structure of ultimate catalyst layers, as evidenced by mercury porosimetry and scanning electron microscopy. For mixed solvents with a higher boiling point, the catalyst–ionomer aggregates in the ink tend to agglomerate during the solvent evaporation process and finally form larger catalyst–ionomer aggregates in the ultimate catalyst layer, resulting in more secondary pores and thus lower mass transport resistance. Both the enlarged catalyst/ionomer interface and appropriate pore structure were achieved with the catalyst layer fabricated from an n-PA/H 2 O mixture with 90 wt % H 2 O, leading to the best MEA performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Particle Migration in Large Cross-Section Ceramic On-Demand Extrusion Components

Ceramic On-Demand Extrusion (CODE) is a direct ink writing process which allows for the creation of near theoretically dense ceramic components with large cross-sections due to oil-assisted drying. Here, Yttria-stabilized zirconia (YSZ) colloidal pastes were used in CODE to produce dense (multi-road infill and ≳ 98% relative density), large continuous volume (> 1 cm 3 ), and high fidelity (nozzle diameters ≲ 1 mm) structural ceramic components with nanoparticle feedstocks (~d 50 ≲ 1 µm). However, many of these printed components underwent significant particle migration after forming. The reason for this particle migration defect was investigated using the coffee-ring effect for dilute solutions and rheological methods for dense suspensions. Modifications to the colloidal paste, such as changes in solids loading, pH, or surfactant concentration were explored as to their effectiveness to mitigate the defect. Ultimately, paste formulation and printing trade-offs are discussed with respect to the post-printing defect and as to general direct-write patterning.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Shelf-life of ball-milled catalyst inks for the fabrication of fuel cell electrodes

A major factor driving fuel cell costs is the quantity of precious metal required. Therefore, it is important to understand a timeframe where inks can be reused. Here, in this work, we explore differences between a freshly prepared catalyst ink and one that has been stored for over a year – comparing ink properties, cathode catalyst layer microstructure, and their respective fuel cell performance. Ink studies revealed smaller agglomerate sizes and a decrease in shear viscosity for the aged ink. Longer storage time also results in fewer cracks and a more uniform ionomer distribution, as evidenced by microscopy characterization of rod-coated electrodes. Lastly, polarization curves show improved performance at higher current densities for the electrode prepared from the aged ink. We rationalize such effect in terms of enhanced ionomer adsorption onto the catalyst over time.

08 HYDROGEN↗
DOE OSTI2021

3D Printing of Transparent Silicone Elastomers

Here in this paper, inks for transparent elastomers that are formulated by matching the refractive index of silica and polysiloxanes are described. The transparent inks transmit up to ≈90% of 700 nm light through 1 cm and remain transparent when solidified. The inks and solidified materials exhibit a thermochromic effect. This thermochromic effect can be controlled by the refractive index mismatch. Transparency may increase or decrease as temperature increases, depending on the refractive index mismatch of the base polysiloxane and silica. It is found that the rheological properties of the ink depend on the distribution of silica particles, which is dictated by silica functionality, weight content, and processing. Siloxane precursors that vary in chemical functionality are introduced to tailor the mechanical properties of the printed elastomers, which obtain stretchability >65% along with a tensile modulus of 1.9 MPa. After optimizing siloxane chemistry and ink processing, the authors are able to print transparent elastomers. Potential applications are demonstrated for printed structures by printing encapsulation structures for light-emitting diodes, semitransparent dye-filled structures, a microfluidic mixing device, and a multimaterial structure that exhibits temperature-dependent camouflage.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The influence of electrode crack dimensions on the durability of polymer electrolyte membrane fuel cells

Electrode cracks in polymer electrolyte membrane fuel cells (PEMFCs) are correlated with early onset failures. Here, in this work we investigate the influence of cracked gas diffusion electrodes (GDEs) on the durability of the membrane electrode assembly (MEA) using a combined chemical-mechanical accelerated stress test (AST). Electrode crack dimensions were systematically tuned using ink formulations and material selection strategies. A parameter to describe the crack width areal density (Φ CW ) was used to quantify the degree of discontinuity in the electrode surfaces. Open circuit voltage (OCV) transient analyses were used to benchmark and characterize the failure mechanisms in the MEAs as a function of the Φ CW . While smaller electrode-level cracks, on the order of microns, yielded a 28 % decrease in operating lifetime, larger cracks that propagated from a discontinuous, microporous layer (MPL) coating, decreased the operating lifetime by 56 %. This work emphasizes the need for material processing strategies that consider defect tolerances to limit membrane failures in PEMFCs.

08 HYDROGEN↗
DOE OSTI2022

Catalyst layer formulations for slot-die coating of PEM fuel cell electrodes

The series of electrodes were fabricated by the scalable and manufacturable slot-die coating method for proton exchange membrane fuel cell (PEMFC) application. The inks with different amounts of solids were studied by rheological methods in order to establish a coating window with minimum manufacturing defects. The obtained electrodes were characterized by SEM, AFM, and optical microscopy, which showed that they were uniform and homogeneous with minimum defects. The electrochemical evaluation of the manufactured gas diffusion electrodes (GDE) showed that the main characteristics of the electrodes, like electrochemical surface area, proton resistivity, and double layer capacitance, were found to be close for all samples confirming the reproducibility of the slot-die process. Additionally, we studied the effects of membrane thickness on the performance of the GDE membrane electrode assemblies and determined that a decrease in membrane thickness favored the performance. Furthermore, the obtained results clearly demonstrated the applicability and feasibility of the approach for the Manufacturing of catalyst layers for the fuel cell application with potential for future mass production.

08 HYDROGEN↗
DOE OSTI2025

Multimaterial 3D Printing in Activating Bath Enables In Situ Polymerization of Thermosets with Intricate Geometries and Diverse Elastic Behaviors

Polydicyclopentadiene, p(DCPD), is a high‐performance thermoset valued for its exceptional toughness, strength, and stiffness. When copolymerized with 1,5‐cyclooctadiene (COD), its mechanical properties can be tuned from glassy to rubbery at room temperature. While frontal polymerization enables a rapid and energy‐efficient route to 3D print DCPD‐based materials, challenges such as ink shelf life and gravitational distortion, especially in direct ink writing of soft COD‐rich formulations, must be considered. Here, a complementary chemical strategy is presented, embedded 3D printing, that enables localized in situ polymerization of printed DCPD/COD inks within a reactive support matrix. The matrix provides both physical support and a reservoir of chemical activator, which diffuses into the ink, activates a latent bis(N‐heterocyclic carbene) Ru precatalyst, and initiates ring‐opening metathesis polymerization. Curing begins at the ink–matrix interface and propagates inward via diffusion, stabilizing the interface and preventing capillary‐driven deformation regardless of the matrix yield stress. This approach eliminates the need for cold storage, external curing, or photoinitiation, significantly expanding the processing window. Using this method, diverse thermosetting and elastomeric architectures are fabricated with features as small as 5 µm and aspect ratios of 100, including interlinked chains, shallow spherical shells exhibiting snap‐through buckling, and hair‐like fin arrays inaccessible through traditional techniques.

chemical activation↗
NASA NTRS2002

Molten-Metal Droplet Deposition on a Moving Substrate in Microgravity: Aiding the Development of Novel Technologies for Microelectronic Assembly

Driven by advancements in microelectronics manufacturing, this research investigates the oblique (non-axisymmetric) impact of liquid-metal droplets on flat substrates. The problem of interest is relevant to the development of the novel technology of on-demand dispension (printing) of microscopic solder deposits for the surface mounting of microelectronic devices. The technology, known as solder jetting, features on-demand deposition of miniature solder droplets (30 to 120 microns in diameter) in very fine, very accurate patterns using techniques analogous to those developed for the ink-jet printing industry. Despite its promise, severe limitations exist currently with regards to the throughput rates of the technology; some of these limitations are largely due to the lack of the capability for reliable prediction of solder bump positioning and shapes, especially under ballistic deposition conditions where the droplet impact phenomena are inherently three-dimensional. The study consists of a theoretical and an experimental component. The theoretical work uses a finite element formulation to simulate numerically the non-axisymmetric (3-D) fluid mechanics and heat transfer phenomena of a liquid solder droplet impacting at an angle alpha on a flat substrate. The work focuses on the pre-solidification regime. The modeling of the most challenging fluid mechanics part of the process has been completed successfully. It is based upon the full laminar Navier-Stokes equations employing a Lagrangian frame of reference. Due to the large droplet deformation, the surface (skin) as well as the volumetric mesh have to be regenerated during the calculations in order to maintain the high accuracy of the numerical scheme. The pressure and velocity fields are then interpolated on the newly created mesh. The numerical predictions are being tested against experiments, for cases where wetting phenomena are not important. For the impact parameters used in the example shown (We = 2.38, Fr = 16300, Re = 157), the droplet rolls along the substrate, but its shape remains practically axisymmetric for all impact angles within the range from 0 to 60 deg. Interestingly, the substrate/droplet contact area during the recoiling phase of the impact is not a monotonically decreasing function of time. The experimental component of the research tests the numerical predictions and provides necessary input data (contact angles) for the theoretical model. The experiments are performed in microgravity (2.2s drop tower of the NASA GRC) in order to allow for the use of mm-size solder droplets, which make feasible the performance of accurate measurements, while maintaining similitude of the relevant fluid dynamic groups (Re, Fr, We, Ste). Preliminary oblique impact experiments have been performed using water droplets in normal gravity.

Megaridis, C. M.↗
NASA NTRS2015

Solid State Ultracapacitor

NASA analyzes, tests, packages, and fabricates electrical, electronic, and electromechanical (EEE) parts used in space vehicles. One area that NASA wishes to advance is energy storage and delivery. Currently, space vehicles use rechargeable batteries that utilize silver zinc or lithium ion electrochemical processes. These current state-of-the-art rechargeable batteries cannot be rapidly charged, contain harmful chemicals, and suffer from early wear-out mechanisms. A solid state ultracapacitor is an EEE part that offers significant advantages over current electrochemical and electrolytic devices. The objective of this research is to develop an internal barrier layer ultracapacitor (IBLC) using novel dielectric materials as a battery replacement with a focus on these advantages: longer life, lower mass-toweight ratio, rapid charging, on-demand pulse power, improved on-pad standby time without maintenance, and environmental friendliness. The approach is unique in two areas. A deposition technique is used that has been shown to produce a more uniformly coated nanoparticle than sol-gel, which has resulted in colossal permittivities. These particles are then distributed in an ink formulation developed at NASA Marshall Space Flight Center (MSFC) and deposited utilizing a 3D aerosol jet technique. This additive manufacturing technique controls layer thickness, resulting in extremely large capacitance and energy density.

Rolin, Terry D.↗
DOE OSTI2021

Solvent absorption rate of perfluorosulphonic acid membranes towards understanding direct coating processes

Here we present a method for measurement of the rate of solvent absorption by perfluorosulfonic acid (PFSA) membranes using a force tensiometer. The method presented here can be used as a tool to understand solvent absorption and should provide a rationale for designing catalyst inks for direct coating processes since it is necessary to understand how the absorption rate – on a time scale of seconds to minutes – compares to the time scales of the coating process in order to minimize membrane swelling. This method allows for rapid screening of the absorption and swelling behavior of different solvents and mixtures. Using this method, the absorption of water/1-propanol mixtures were measured for three thicknesses of Nafion PFSA membrane – Nafion 1135, Nafion 115, and Nafion 117. We find that the absorption rate is dependent on the ratio of the solvents as well as the thickness of the membrane. The analysis indicates that the highest absorption rate occurs when the mass percentage of 1-propanol in the mixture is 50%, whereas the lowest rates are for pure water and 1-propanol. In addition, membrane distortion also occurs most quickly for the 50% 1-propanol mixture. Our results suggest that catalyst inks that are highly rich (=90%) in water or 1-propanol are likely best for direct coating as such formulations will minimize absorption and swelling.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Roll to Roll (R2R) Manufacturing of Electrolysis Electrodes for Low Cost Hydrogen Production: Cooperative Research and Development Final Report, CRADA Number CRD-18-00780

NREL, Argonne National Laboratory (ANL) and Oak Ridge National Laboratory (ORNL), which are also referred to collectively herein as the "Contractors" will perform electrode ink development and characterization, focusing on 1) inks with appropriate properties for R2R (gravure and slot-die) coating onto PFSA membrane and 2) catalysts suitable for electrolysis. Participant will develop acceptance criteria and characterization methods for direct coating on the membrane. The purpose of this project is to show feasibility for cost reduction of the electrode through increased throughput and improved material utilization. Successful completion of this project will result in more affordable hydrogen production via proton exchange membrane (PEM) electrolysis by substantially reducing the anode precious metal content and catalyst-coated membrane processing costs. Assists laboratory in achieving programmatic scope, adds new capability to the laboratory's core competencies. This project uses and enhances the laboratory's core competencies, and enhances U.S. competitiveness by utilizing DOE developed intellectual property and/or capabilities. This project will benefit the Fuel Cell subprogram within the EERE Fuel Cell Technologies Office (FCTO) by actively developing materials, formulations, components, and processes for PEM electrolyzer stacks for overcoming critical technical barriers to widespread hydrogen production for zero-emission transportation applications. Through this JWS, NREL, ANL and ORNL are assisting a key domestic industry partner, Proton Energy Systems, Inc., in the area of low-cost electrolyzer electrode formulation and coating technology. After completion of this project, NREL, ANL and ORNL will be able to verify whether the direct deposit coating processes investigated are suitable for producing CCMs for PEM electrolyzers, which is of great interest and benefit to the DOE EERE Fuel Cell Technologies Office (FCTO) and H2@Scale missions.

08 HYDROGEN↗