Results for “interfacial stabilization” — Page 4

DOE OSTI2022

Evaluating Contributions of Pitch-Carbon Coating to Improved Stability of Si Anodes Through Voltage-Resolved Multi-Phase Characterization

Silicon nanoparticles have emerged as a promising alternative to graphite to improve the energy density of next-generation lithium-ion battery anodes. Nano-sized Si domains facilitate rapid ion transport and minimize particle-scale mechanical degradation, but also exhibit increased (electro)chemical reactivity with Li-ion electrolyte components due to their high surface area. We have previously demonstrated that surface modification of Si nanoparticles with pitch-carbon is an effective strategy to reduce these parasitic reactions. In the present work, we holistically evaluate the mechanistic contribution of pitch-carbon coating to the observed stability improvement over uncoated Si. We utilize coupled in situ and ex situ methods to probe changes to solid-surface, volatile headspace, and gas-phase chemistry occurring during initial cycling. Measurements taken at targeted potentials associated with electrolyte species reduction enables the decoupling of specific reaction pathways tied to interfacial stability. Further, we demonstrate the non-trivial role of gas reconsumption in dictating the nature of the passivating surface layer evolved on both uncoated and pitch-coated Si. This multi-phase analysis offers insights into the mechanism of effective surface passivation, which may be applied to inform future Si material development.

ENERGY STORAGE↗

DOE OSTI2023

The nature and suppression strategies of interfacial reactions in all-solid-state batteries

Solid-state Li batteries are promising energy storage devices owing to their high safety and high theoretical energy density. However, the serious interfacial reaction between solid state electrolytes and cathodes deteriorates the battery performance, impeding the realization of long-term cyclability. The buried nature of the interphase layer presents a significant challenge in achieving a comprehensive understanding of the underlying interfacial reaction mechanisms. Herein, we systematically explore the interfacial reaction evolutions and interphase compositions and electronic properties between the popular oxide cathodes and sulfide solid electrolytes (SSEs). This includes analysis of the chemical and electrochemical reactions between cathodes/coatings and SSEs, as well as the electrochemical self-decomposition of SSEs by thermodynamic phase equilibrium analysis. Herein, we disclose that the driving force of the electrochemical reaction at the chemical potential of μ Li is much stronger than that of the chemical reaction, which dominates the interfacial reaction. Preventing the formation of an electronically conductive interphase is crucial in inhibiting the continuous interfacial degradation during long-term cycling, which can be achieved through the optimized combination of cathodes and SSEs, as well as the introduction of functional coatings between them. Based on these findings, the percentage of molar fraction ( f ) of electronically conductive species in the formed interphase is proposed as a key factor for indicating the interfacial stability for the first time. Furthermore, we propose a specific high-throughput screening scheme to filter the functional coating materials by comprehensively evaluating their functionality. The tiered screening identifies 48 coating materials with optimal properties. The work highlights the significant roles of rational coupling of the cathodes and SSEs, and optimizing interfacial coating materials for solid-state batteries. It opens new avenues for engineering an interphase with improved interfacial compatibility to realize long-term cyclability.

25 ENERGY STORAGE↗

DOE OSTI2023

Development of Corrosion Resistant Coatings for Structural Materials for Liquid Fueled Molten Salts Reactors Applications (Final Report)

Current structural alloys, code certified for the MSRs temperature ranges, contain high levels of chromium, making them highly susceptible to molten halide salt corrosion. One potential solution to circumvent the need for code certification of novel alloys, which is expensive and time consuming, is to design claddings that will protect the underlying code certified materials from corrosion damage during operation. In this work, we examined the corrosion of Ni and Cu electroplated, Ni and CuNi weld overlay, Mo-laser clad, and carburized claddings on SS316H for use in molten salt reactor environments. After characterization of the cladded materials (Task 1), static corrosion tests were used to assess corrosion resistance of the claddings in typical molten fluoride salts (Task 2). The corrosion tests were performed in molten FLiNaK at 700°C up to 1000 hours. Pre- and post-corrosion Scanning Electron Microscopy (SEM), energy-dispersive-spectroscopy (EDS), Transmission Electron Microscopy (TEM), X-ray Diffraction (XRD) and glow-discharge-optical-emission-spectroscopy (GDOES) were performed on cladding cross-sections and surfaces to evaluate degradation. The Cu and Ni electroplated samples, as well as the carburized samples, showed excellent corrosion resistance relative to the bare SS316H. To assess high temperature cladding stability, ageing experiments were performed at temperatures up to 900 C in inert atmosphere for the electroplated and carburized samples and a diffusion model was developed to predict long term cladding behavior (Task 3). It was found that the Cu cladding was basically insensitive to the high temperature ageing, except for small secondary phases forming at the interface. On the other hand, the Ni electroplated cladding experienced significant interdiffusion. Nevertheless, the gain in corrosion resistance for a 100μm Ni electroplated cladding is phenomenal, with more than 50% reduction in chromium dissolution from the substrate material for the first 15 years of salt exposure at 700°C. To assess radiation resistance and phase stability, high-temperature 4MeV Ni heavy ion irradiation was performed across the cladding/substrate interface up to 50 displacement-per-atom (DPA) at 500°C and 700°C to assess the phase stability and irradiation behaviors of the electroplated systems (Task 4). The Ni and Cu electroplated systems did not experience void swelling at the contrary to the SS316H substrate due to their nanocrystalline nature. Some level of recrystallization was observed in the cladding, as well as radiation induced segregation and enhanced diffusion. The interface acted as a potent sink for point defects with the presence of a void denuded zone. The mechanical properties of the claddings were assessed using thermal shock, micro-indentation, nano-indentation, and four-point bend testing experiments (Task 5). These experiments were performed on the claddings in as-received, corroded, irradiated, and thermally aged states to determine the effects of typical molten salt reactor environments on cladding integrity. No significant mass loss was observed after repeated thermal shocks. While the electroplated samples softened after high-temperature ageing, irradiation hardening compensate this effect, such that there is little different with the as-received materials. The results of these experiments suggest that the electroplated (copper/nickel) show the greatest promise for application in molten salt reactor development. These claddings prevented any chromium dissolution from occurring during the static corrosion experiments. Additionally, they demonstrated favorable properties for high temperature diffusion, phase stability, interfacial mechanical properties, and irradiation resistance. Weld-overlay cladding are also of great interest and could reach properties similar to the electroplated samples upon optimization (especially with multiple weld passes). The carburized SS316H showed excellent behavior as well, but more work needs to be done to assess their long-term stability. Finally, the Mo-laser clad system was not pursued further due to the manufacturing challenges. It is also worth noting that the Ni cladding systems should behave relatively well in terms of weldability since the Ni-weld overlay microstructure and associated corrosion rate are sound. While the NiCu weld-overlay has even lower corrosion rates than the Ni-weld overlay, more studies on welding of Cu-electroplated systems are necessary since Cu clusters are known to embrittle steels.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Time-Evolved Hetero-Alkali Interphases Enable Long-Life Sulfide-Based Anode-Free Solid-State Batteries

Sulfide-based anode-free solid-state batteries (AFSSBs) offer compelling advantages in terms of energy density and safety, yet their practical implementation is severely hindered by undesirable interfacial reactions between sulfide solid electrolytes (SEs) and freshly plated lithium (Li), as well as non-uniform Li plating/stripping behavior. Herein, an effective interfacial stabilization strategy by incorporating sodium bis(fluorosulfonyl)imide (NaFSI) additive into the Li5.4PS4.4Cl1.6 (LPSC) is investigated. Unlike conventional Li-based additives that form static passivation layers, NaFSI introduces a transient hetero-alkali chemistry that kinetically governs interphase evolution during fresh Li plating. NaFSI induces a timesequenced interphase evolution: an initial NaF/LiF-rich layer that suppresses early sulfide reduction, followed by a LiF/Li3N-rich layer that optimizes Li⁺ transport during repeated anode-free cycling. This evolved robust and fast ion conducting layer mitigates interfacial impedance growth, enhances Li + transport kinetics, and suppresses localized Li growth and filamentary shorting. As a result, the anode-free full cell with NaFSI modified LPSC as the interlayer exhibits an excellent cycling stability over 500 cycles at 0.2 C with a capacity retention of 77.6%, whereas the cell with bare LPSC suffers from rapid capacity decay after 100 cycles, retaining only 32.1% of its initial capacity. This work establishes dynamic heteroalkali additive chemistry as a general strategy to kinetically program solid-solid interphases, guiding the interface design in anode-free solid-state batteries.

25 ENERGY STORAGE↗

DOE OSTI2024

In Situ Characterization of Interface Evolution in Argyrodite‐Based All‐Solid‐State Li Batteries

Interfacial stability is one of the critical challenges in all-solid-state Li metal batteries. Multiple processes such as solid electrolyte (SE) decomposition and lithium dendrite growth take place at the solid interfaces during cycling, leading to the overall cell failure. To deconvolute these complex processes, in situ characterization is of paramount importance to elucidate the interfacial evolution on the SE upon Li plating/stripping. Herein, an all-solid-state asymmetric in situ cell is developed that allows the direct visualization of the highly localized Li plating/stripping processes under the optical microscope. Moreover, this cell configuration enables reliable post-mortem chemical and morphological analysis of the intact SE/Li interface. Using combined scanning electron microscopy and energy-dispersive X-ray spectroscopy, the study reveals that the evolution of the Li argyrodite interface is strongly influenced by the current density, particularly in terms of chemical distribution and Li plating morphology. More specifically, the solid interface is LiCl-rich with the formation of Li cubes at low current densities, while high currents result in more uniform elemental distribution and filament morphology. These findings elucidate the dynamic evolution mechanism at solid interfaces and offer valuable guidance for developing stable solid interfaces in all-solid-state Li metal batteries.

Huang, Di↗

DOE OSTI2025

Delineating the Factors Impacting the Electrochemical Behavior of Single-Crystal High-Nickel Layered Oxide Cathodes

High-nickel (Ni) (≥80%) single-crystal LiNi 1-x-y Mn x Co y O 2 (NMCs) have garnered recent interest as cathodes in lithium (Li)-ion batteries (LIBs). However, capacity fade at high voltages, particularly after the onset of the H2–H3 phase transition, hampers their viability. In this study, single-crystal LiNi 0.8 Mn x Co 0.2-x O 2 (x = 0.2, 0.1, 0) are synthesized and tested in LiPF 6 in ethyl methyl carbonate-based electrolytes, with and without monofluoroethylene carbonate and LiF 2 PO 2 additives, to clarify the effects of Co/Mn ratio and surface stabilization on high-voltage cycling degradation. By imposing a kinetic barrier to the accessible H2–H3 capacity, surface reconstruction is identified as the primary driver of high-voltage capacity loss, being greater in the Co-free cathode and in the absence of fluorinated electrolyte components. This is attributed to a synergy between increased mechanical stress due to worsened bulk and interfacial H2–H3 kinetics and decreased interfacial stability due to the poor passivating capability of the electrolyte. Here, the findings highlight the importance of limiting cathode impedance growth during high-voltage cycling, which can be achieved by tuning bulk dopants and electrolyte chemistry.

25 ENERGY STORAGE↗

DOE OSTI2024

In Situ Cyclized Polyacrylonitrile Coating: Key to Stabilizing Porous High-Entropy Oxide Anodes for High-Performance Lithium-Ion Batteries

High-entropy oxides (HEOs) composed of multiple metal elements have attracted great attention as anode materials for lithium-ion batteries (LIBs) due to the synergistic effects of various metal species. However, the practical applications of HEOs are still plagued by poor conductivity, unstable solid electrolyte interphase (SEI) and poor cycling stability. In this work, nanosized (FeCoNiCrMn) 3 O 4 HEO (NHEO) is prepared successfully by the NaCl-assisted mechanical ball-milling strategy. Novelly, polyacrylonitrile (PAN) is used as the binder and then in situ thermochemically cyclized to construct a cyclized PAN (cPAN) outer layer onto NHEO (NHEO-cPAN). The in situ formed cPAN coating not only improves the electrical conductivity, but also reinforces the structural and interfacial stability, and thereby, the resulted NHEO-cPAN electrode exhibits significantly enhanced rate and cyclic performance. Specifically, NHEO-PAN500 electrode delivers a high reversible capacity of 560 mAh g –1 at 5 A g –1 and a high-capacity retention of 83% over 800 cycles at 3 A g –1 . Furthermore, the structural evolution and electrochemical behavior of NHEO-PAN electrode during discharge/charge is systematically investigated by operando X-ray diffraction, in situ impedance spectroscopy and ex situ high-resolution transmission electron microscopy. Therefore, this work provides new insights into the engineering of electrode and interphase for high-performance HEO electrode materials, potentially enlightening the practical applications of HEO-based LIBs.

25 ENERGY STORAGE↗

DOE OSTI2023

Multiscale characterization of an additively manufactured property graded Ni-base alloy for molten-salts\supercritical-CO 2 heat exchangers

The sequential optimization of strength and corrosion resistance in conventional alloy design procedures often results in a tradeoff between environmental degradation and optimal mechanical properties. A concurrent optimization of these two material properties is essential to efficiently develop high temperature alloys that can withstand harsh environments increasingly required for carbon–neutral energy technologies. In this work, we demonstrate the feasibility of directed energy deposition (DED) to manufacture a dual-corrosion resistant Ni-based alloy (Hastelloy N and Haynes 282), that meets the high temperature operation requirements of a molten-salts\supercritical-CO 2 (sCO 2 ) heat exchanger. A combination of multiscale characterization techniques and computational thermodynamics was employed to evaluate the cracking susceptibilities during fabrication and predict the microstructural stability of the material. Very good agreement was achieved between the observed and predicted phases and phase fractions of the as-printed material. A careful characterization of the transition zone between the two terminal alloy chemistries revealed potential precipitation strengthening (γ') on the Hastelloy N side while columnar-shaped M 23 C 6 and γ' precipitates that formed at grain boundaries (GBs) of the transition zone likely minimized the local interfacial energies. Both these mechanisms are believed to increase the interfacial stability but their performance at high temperatures requires further investigation.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Steric Effect Tuned Ion Solvation Enabling Stable Cycling of High-Voltage Lithium Metal Battery

1,2-Dimethoxyethane (DME) is a common electrolyte solvent for lithium metal batteries. Various DME-based electrolyte designs have improved long-term cyclability of high-voltage full cells. However, insufficient Coulombic efficiency at the Li anode and poor high-voltage stability remain a challenge for DME electrolytes. Here, we report a molecular design principle that utilizes a steric hindrance effect to tune the solvation structures of Li + ions. In this work, we hypothesized that by substituting the methoxy groups on DME with larger-sized ethoxy groups, the resulting 1,2-diethoxyethane (DEE) should have a weaker solvation ability and consequently more anion-rich inner solvation shells, both of which enhance interfacial stability at the cathode and anode. Experimental and computational evidence indicates such steric-effect-based design leads to an appreciable improvement in electrochemical stability of lithium bis(fluorosulfonyl)imide (LiFSI)/DEE electrolytes. Under stringent full-cell conditions of 4.8 mAh cm –2 NMC811, 50 μm thin Li, and high cutoff voltage at 4.4 V, 4 M LiFSI/DEE enabled 182 cycles until 80% capacity retention while 4 M LiFSI/DME only achieved 94 cycles. This work points out a promising path toward the molecular design of non-fluorinated ether-based electrolyte solvents for practical high-voltage Li metal batteries.

25 ENERGY STORAGE↗

DOE OSTI2026

Amphiphilic Baskets for Supramolecular Nanoarchitectures at Interfaces: Inverted Monolayer Formation on Water

Interfacial chemistry of molecular baskets remains poorly understood despite their promise for supramolecular applications of detection and sequestration of toxic molecules including those of illicit drugs, organophosphorus compounds, and anticancer agents. We present a fundamental investigation of the interfacial behavior of three amphiphilic supramolecular baskets (ASB 4, 8, and 12), having increasingly longer yet linear alkyl chains at the top of their bowl-shaped cavity. The studies were completed at the air−water interface to elucidate surface activity, interfacial stability, self-assembly, and monolayer organization that drive inverted monolayer formation, in which the molecular arms orient toward the aqueous phase in a configuration opposite to that typically observed for lipids. Herein, surface pressure−area isotherms of ASB 4, 8, 12, deposited on a water surface, were performed in tandem with nonequilibrium relaxation experiments to quantify surface activity, thermodynamic stability, and monolayer compressibility of the baskets’ monolayer assembly. Brewster angle microscopy enabled direct visualization of morphological evolution, aggregation, and packing at the interface. We show that systematic extension of the hydrocarbon arms, from four to 12 methylene groups, progressively modifies intermolecular packing, drives distinct two-dimensional aggregation pathways, and increases number densities at the air−water interface. Atomistic molecular dynamics simulations corroborate many of these experimentally observed trends and provide mechanistic detail on the cooperative roles of basket topology and interfacial concentration in regulating the hydration structure and dynamics within the cavities generated by surface-adsorbing baskets, consistent with observed variations in surface activity and packing. Our results establish how the topology of these unique supramolecules and their concentration govern interfacial organization and offer a rational framework for designing amphiphiles with predictable behavior at soft interfaces.

Hydrocarbons↗

DOE OSTI2024

Multiple Functional Bonds Integrated Interphases for Long Cycle Sodium-Ion Batteries

Sodium-ion batteries (SIBs) have garnered significant interest as one of the most promising energy suppliers for power grid energy storage. However, the poor electrode/electrolyte interfacial stability leads to continual electrolyte decomposition and transition metal dissolution, resulting in rapid performance degradation of SIBs. In this work, we propose a strategy integrating multiple functional bonds to regulate electrode/electrolyte interphase by triple-coupling of succinonitrile (SN), sodium hexafluorophosphate (NaPF 6 ) and fluorinated ethylene carbonate (FEC). Theoretical calculation and experiment results show that the solvation structure of Na + and ClO 4 – is effectively reconfigured by the solvated FEC, SN and PF 6 – in PC-based carbonate electrolyte. The newly developed electrolyte demonstrates increased Na + -FEC coordination, weakened interaction of Na + -PC and participation of SN and PF 6 – anions in solvation, resulting in the formation of a conformal interfacial layer comprising of sodium oxynitrides (NaN x O y ), sodium fluoride (NaF) and phosphorus oxide compounds (NaP x O y ). Consequently, a 3 Ah pouch full cell of hard carbon//NaNi 1/3 Fe 1/3 Mn 1/3 O 2 exhibits an excellent capacity retention of 90.4 % after 1000 cycles. Detailed postmortem analysis of interface chemistry is further illustrated by multiple characterization methods. Finally, this study provides a new avenue for developing electrolyte formulations with multiple functional bonds integrated interphases to significantly improve the long-term cycling stability of SIBs.

25 ENERGY STORAGE↗

DOE OSTI2023

Development, Characterization, and Testing of Solid-State Electrolytes for Batteries

Traditional liquid electrolytes used in lithium (Li) metal batteries (LMBs) have severe safety issues, poor power density, as well as thermal and electrochemical instability that prevents their scaling to newer applications, such as electric vehicles. Using sulfide-based solid-state electrolytes (SSEs) is a viable method to address many of the issues that plague LMBs. However, the key issue preventing the expansion of sulfide-based SSEs is an interplay between poor interfacial stability with the electrodes and massive external stack pressure required to maintain electrode-electrolyte contact. The need for extensive pressure requires large system-level (i.e., battery pack used in an electric vehicle) housing that causes a disconnect between performance at a smaller scale and actual application. Secondary prevention to sulfide-based SSE adoption are difficulties in manufacturing, as toxic deterioration occurs when these materials are exposed to humidity, as well as drastic reduction in SSE performance at low temperature. This work hypothesizes that unique interfacial designs of electrodes and the modification of the sulfide-based SSE will enable reduction of necessary external cell pressure, and therefore support the design of practical LMBs. This will be done through collaboration within Idaho National Laboratory (INL), where manufacturing practices will be parameterized to produce low defect, low porosity SSEs with slight modifications. Next, artificial interfaces will be produced on electrodes to observe the conformality and mass transport properties between the modified SSE and pre-treated anode. External pressure on Li-metal cells will also be parameterized to reduce interfacial impedance while a reduction in the pressure will allot reasonable housing design for larger scale applications. Focus on novelty in this work occurs by modifications to the solid-solid interfaces between electrolyte and electrode, done through doping of the electrolyte and production of artificial interfaces on the Li-metal anode. The modifications at these interfaces, in addition to modified external pressure could identify and address the poor interfacial impedance that hinders high performance SSEs. Fundamental understanding on how to reduce the key hindrances of all-solid-state batteries (ASSBs) will support the advancement for larger scale production and performance, of which will be held in perspective for future works. Beyond battery development, the knowledge gained from process control and defect analysis is applicable to other ceramic systems, such as nuclear fuel coatings and high temperature electrolyzers.

25 ENERGY STORAGE↗

DOE OSTI2023

Development, Characterization, and Testing of Solid-State Electrolytes for Batteries

Traditional liquid electrolytes used in lithium (Li) metal batteries (LMBs) have severe safety issues, poor power density, as well as thermal and electrochemical instability that prevents their scaling to newer applications, such as electric vehicles. Using sulfide-based solid-state electrolytes (SSEs) is a viable method to address many of the issues that plague LMBs. However, the key issue preventing the expansion of sulfide-based SSEs is an interplay between poor interfacial stability with the electrodes and massive external stack pressure required to maintain electrode-electrolyte contact. The need for extensive pressure requires large system-level (i.e., battery pack used in an electric vehicle) housing that causes a disconnect between performance at a smaller scale and actual application. Secondary prevention to sulfide-based SSE adoption are difficulties in manufacturing, as toxic deterioration occurs when these materials are exposed to humidity, as well as drastic reduction in SSE performance at low temperature. This work hypothesizes that unique interfacial designs of electrodes and the modification of the sulfide-based SSE will enable reduction of necessary external cell pressure, and therefore support the design of practical LMBs. This will be done through collaboration within Idaho National Laboratory (INL), where manufacturing practices will be parameterized to produce low defect, low porosity SSEs with slight modifications. Next, artificial interfaces will be produced on electrodes to observe the conformality and mass transport properties between the modified SSE and pre-treated anode. External pressure on Li-metal cells will also be parameterized to reduce interfacial impedance while a reduction in the pressure will allot reasonable housing design for larger scale applications. Focus on novelty in this work occurs by modifications to the solid-solid interfaces between electrolyte and electrode, done through doping of the electrolyte and production of artificial interfaces on the Li-metal anode. The modifications at these interfaces, in addition to modified external pressure could identify and address the poor interfacial impedance that hinders high performance SSEs. Fundamental understanding on how to reduce the key hindrances of all-solid-state batteries (ASSBs) will support the advancement for larger scale production and performance, of which will be held in perspective for future works. Beyond battery development, the knowledge gained from process control and defect analysis is applicable to other ceramic systems, such as nuclear fuel coatings and high temperature electrolyzers.

25 ENERGY STORAGE↗

DOE OSTI2023

Sodium Carbazolide and Derivatives as Solid‐State Electrolytes for Sodium‐Ion Batteries

Abstract Replacing widely used organic liquid electrolytes with solid‐state electrolytes (SSEs) could effectively solve the safety issues in sodium‐ion batteries. Efforts on seeking novel solid‐state electrolytes have been continued for decades. However, issues about SSEs still exist, such as low ionic conductivity at ambient temperature, difficulty in manufacturing, low electrochemical stability, poor compatibility with electrodes, etc. Here, sodium carbazolide (Na‐CZ) and its THF‐coordinated derivatives are rationally fabricated as Na + conductors, and two of their crystal structures are successfully solved. Among these materials, THF‐coordinated complexes exhibit fast Na + conductivities, i.e., 1.20×10 −4 S cm −1 and 1.95×10 −3 S cm −1 at 90 °C for Na‐CZ‐1THF and Na‐CZ‐2THF, respectively, which are among the top Na + conductors under the same condition. Furthermore, stable Na plating/stripping is observed even over 400 h cycling, showing outstanding interfacial stability and compatibility against Na electrode. More advantages such as ease of synthesis, low‐cost, and cold pressing for molding can be obtained. In situ NMR results revealed that the evaporation of THF may play an essential role in the Na + migration, where the movement of THF creates defects/vacancies and facilitates the migration of Na + .

Yu, Yang↗

DOE OSTI2023

Sodium Carbazolide and Derivatives as Solid‐State Electrolytes for Sodium‐Ion Batteries

Abstract Replacing widely used organic liquid electrolytes with solid‐state electrolytes (SSEs) could effectively solve the safety issues in sodium‐ion batteries. Efforts on seeking novel solid‐state electrolytes have been continued for decades. However, issues about SSEs still exist, such as low ionic conductivity at ambient temperature, difficulty in manufacturing, low electrochemical stability, poor compatibility with electrodes, etc. Here, sodium carbazolide (Na‐CZ) and its THF‐coordinated derivatives are rationally fabricated as Na + conductors, and two of their crystal structures are successfully solved. Among these materials, THF‐coordinated complexes exhibit fast Na + conductivities, i.e., 1.20×10 −4 S cm −1 and 1.95×10 −3 S cm −1 at 90 °C for Na‐CZ‐1THF and Na‐CZ‐2THF, respectively, which are among the top Na + conductors under the same condition. Furthermore, stable Na plating/stripping is observed even over 400 h cycling, showing outstanding interfacial stability and compatibility against Na electrode. More advantages such as ease of synthesis, low‐cost, and cold pressing for molding can be obtained. In situ NMR results revealed that the evaporation of THF may play an essential role in the Na + migration, where the movement of THF creates defects/vacancies and facilitates the migration of Na + .

Yu, Yang↗

DOE OSTI2025

Polyethylene Glycol Surface Modification and Polythiophene Side-Chain Chemistry: A Combined Strategy toward High-Capacity Lithium-Ion Battery Anodes

In the development of high-capacity lithium-ion batteries (LIBs), the combined optimization of active material interfaces and polymer binder chemistry plays a critical role in improving electrode performance and longevity. This work explores a dual design strategy incorporating polyethylene glycol (PEG) surface modification and carboxylated polythiophene side-chain tailoring to enhance the electrochemical behavior of magnetite (Fe 3 O 4 )-based anodes. PEG is employed to improve interfacial stability, while carboxylated polythiophene binders with varying alkyl side-chain lengths─poly[3-(potassium-4-butanoate)thiophene-2,5-diyl] (P3KBT), poly[3-(potassium-5-pentanoate)thiophene-2,5-diyl] (P3KPT), and poly[3-(potassium-6-hexanoate)thiophene-2,5-diyl] (P3KHT)─are used to modulate molecular interactions and ion transport. Among these three analogs, the PEG–Fe 3 O 4 –P3KHT electrode exhibits superior ion-transfer kinetics, the highest capacity retention, and the lowest charge-transfer resistance after extended cycling. Compared to their non-PEG analogs, PEG-coated electrodes demonstrate enhanced structural integrity and electrochemical behavior, emphasizing the synergistic effects of surface modification and side-chain chemistry. These findings highlight the importance of interfacial interactions and molecular design in achieving robust and high-performance composite anodes for next-generation LIBs.

Fe3O4↗

DOE OSTI2025

Ternary Potassium‐Bismuth‐Telluride Intermetallic Support Promotes Electrochemical Stability in Potassium Metal Anodes

We employed accumulative roll bonding to fabricate self‐standing metallurgical composite of in situ formed alkaline potassium‐bismuth‐telluride intermetallic K 2 (Bi 2/6 Te 3/6 Vac 1/6 ) embedded in potassium metal. This newly discovered thermodynamically stable potassiophilic crystal, termed “KBT”, is fcc antifluorite with K 2 Te archetype. Symmetric cells achieve 880 h of cycling at 0.5 mA cm −2 and 0.5 mAh cm −2 . Potassium metal battery (KMB) with Prussian blue (PB) cathode in carbonate electrolyte retains 80% capacity after 200 cycles at 1C. In ether‐based electrolyte with organic cathode, it achieves 80% retention after 900 cycles at 2C. Combined synchrotron X‐ray nano‐tomography, cryogenic‐focused ion beam microscopy (Cryo‐FIB) and sputter‐down X‐ray photoelectron spectroscopy (XPS) demonstrate uniform electrodeposits, versus baseline of potassium filaments intermixed with pores and coarse SEI. Binary K 3 Bi‐K and K 2 Te‐K intermetallic supports also provide improved electrochemical performance, albeit to lesser extent. Multiscale simulation provides insight into role of support structure in adatom energetics, film nucleation, early‐stage SEI morphology and interfacial stability.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Synthesis of Fluorine-Doped Lithium Argyrodite Solid Electrolytes for Solid-State Lithium Metal Batteries

Solid-state lithium metal batteries (SSLMBs) that utilize novel solid electrolytes (SEs) have garnered much attention because of their potential to yield safe and high-energy-density batteries. Sulfide-based argyrodite-class SEs are an attractive option because of their impressive ionic conductivity. Recent studies have shown that LiF at the interface between Li and SE enhances electrochemical stability. However, the synthesis of F-doped argyrodites has remained challenging because of the high temperatures used in the state-of-the-art solid-state synthesis methods. In this work, for the f irst time, we report F-doped Li 5+y PS 5 F y argyrodites with a tunable doping content and dual dopants (F-/Cl- and F-/Br-) that were synthesized through a solvent-based approach. Among all compositions, Li 6 PS 5 F 0.5 C l0.5 exhibits the highest Li-ion conductivity of 3.5 x 10 -4 S cm -1 at room temperature (RT). Furthermore, Li symmetric cells using Li 6 PS 5 F 0.5 Cl 0.5 show the best cycling performance among the tested cells. X-ray photoelectron spectroscopy and ab initio molecular dynamics simulations revealed that the enhanced interfacial stability of Li 6 PS 5 F 0.5 C l0.5 SE against Li metal can be attributed to the formation of a stable solid electrolyte interphase (SEI)-containing conductive species (Li 3 P), alongside LiCl and LiF. These findings open new opportunities to develop high-performance SSLMBs using a novel class of F-doped argyrodite electrolytes.

25 ENERGY STORAGE↗