Search NASA⌕ Search

SEARCH · Search NASA

Results for “lamellar structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Influence of precipitate morphology on intermediate temperature creep properties of a nickel-base superalloy single crystal

The relative creep behavior of cuboidal (as-heat treated) and rafted (precrept at 1000 C) gamma-prime microstructures in the single-crystal Ni-based superalloy NASAIR 100 at 760 C was investigated using SEM and TEM examinations of materials at various stages of creep. It was found that, at high applied stresses, the crystals with cuboidal gamma-prime structure had both lower minimum creep rates and longer rupture lives than the crystals with lamellar gamma-prime. At lower stress levels, the initially cuboidal gamma-prime microstructure maintained a lower creep rate, but exhibited a similar rupture life compared to the prerafted crystals.

Nathal, M. V.↗

Real-Time X-Ray Microscopy of Al-Cu Eutectic Solidification

Recent improvements in the resolution of the X-ray Transmission Microscope (XTM) for Solidification Studies provide microstructure feature detectability down to 5 micrometers during solidification. This presentation will show the recent results from observations made in real-time of the solid-liquid interfacial morphologies of the Al-CuAI2 eutectic alloy. Lamellar dimensions and spacings, transitions of morphology caused by growth rate changes, and eutectic grain structures are open to measurements. A unique vantage point viewing the face of the interface isotherm is possible for the first time with the XTM due to its infinite depth of field. A video of the solid-liquid interfaces seen in-situ and in real-time will be shown.

Kaukler, William F.↗

Empirical Constraints on Progressive Shock Metamorphism of Magnetite from the Siljan Impact Structure, Sweden

Little is known about the microstructural behavior of magnetite during hypervelocity impact events, even though it is a widespread accessory mineral and important magnetic carrier in terrestrial and extraterrestrial rocks. We report systematic electron backscatter diffraction crystallographic analysis of shock features in magnetite, from a transect across the 52-km diameter ~380 Ma Siljan impact structure in Sweden. Magnetite grains in granitoid samples contain brittle fracturing, crystal-plasticity, and lamellar twins. Deformation twins along {111} with shear direction of <112> are consistent with spinel-law twins. Inferred bulk shock pressures for investigated samples, as constrained by planar deformation features (PDFs) in quartz and shock twins in zircon, range from 0–20 GPa; onset of shock-induced twinning in magnetite is observed at >5 GPa. These results highlight the utility of magnetite to record shock deformation in rocks that experience shock pressures >5 GPa, which may be useful in quartz-poor samples. Despite significant hydrothermal alteration, and variable transformation of host magnetite to hematite, shock effects are preserved, demonstrating that magnetite is a reliable mineral for preserving shock deformation over geologic time.

magnetite↗

Ultrasonic-Assisted Extrusion Processing for Enhancing Physical Properties of High-Density Polyethylene by Flow-Induced Crystallization

The evolution of crystallinity resulting from stress imposed on a melt, known as flow-induced crystallinity, can strongly influence the mechanical and physical properties of semicrystalline polymers. This study investigates shear-induced crystallization by applying an ultrasonic field to the melt flow as it passes through dies with various geometries. A custom-built sonication die is employed for controlling the dynamic temperature and shear environment, resulting in molecular alignment and potential for flow-induced crystallization. Application of both conventional and ultrasonic shear rates at the equilibrium melt temperature of high-density polyethylene (HDPE) was investigated to accelerate crystallinity and manipulate the crystal morphology across the film in pursuit of improved mechanical and gas barrier properties without the need for additives or other polymer layers. The relationships among ultrasonic-assisted extrusion processing, polymer structure, and performance were analyzed using wide- and small-angle X-ray scattering (WAXS and SAXS), tensile testing, and oxygen transmission rate (OTR) analysis. Multiple linear regression models were implemented to predict the correlation among HDPE structure, process, and properties. Structural analysis revealed that both conventional and ultrasonic shear rates had the most significant influence on lamellar spacing and redistribution of rigid and soft amorphous fractions within the crystalline domains, ultimately dictating the mechanical and physical properties of the films. The goal is to explore the potential of the ultrasonic-assisted high crystallinity monolayer that can replace some of the functionality of complex, heterogeneous multilayer packaging with a single-material film having enhanced oxygen barrier properties.

crystallinity↗

Functional nanocomposites prepared by self-assembly and polymerization of diacetylene surfactants and silicic acid

Conjugated polymer/silica nanocomposites with hexagonal, cubic, or lamellar mesoscopic order were synthesized by self-assembly using polymerizable amphiphilic diacetylene molecules as both structure-directing agents and monomers. The self-assembly procedure is rapid and incorporates the organic monomers uniformly within a highly ordered, inorganic environment. By tailoring the size of the oligo(ethylene glycol) headgroup of the diacetylene-containing surfactant, we varied the resulting self-assembled mesophases of the composite material. The nanostructured inorganic host altered the diacetylene polymerization behavior, and the resulting nanocomposites show unique thermo-, mechano-, and solvatochromic properties. Polymerization of the incorporated surfactants resulted in polydiacetylene (PDA)/silica nanocomposites that were optically transparent and mechanically robust. Molecular modeling and quantum calculations and (13)C spin-lattice relaxation times (T(1)) of the PDA/silica nanocomposites indicated that the surfactant monomers can be uniformly organized into precise spatial arrangements prior to polymerization. Nanoindentation and gas transport experiments showed that these nanocomposite films have increased hardness and reduced permeability as compared to pure PDA. Our work demonstrates polymerizable surfactant/silica self-assembly to be an efficient, general approach to the formation of nanostructured conjugated polymers. The nanostructured inorganic framework serves to protect, stabilize, and orient the polymer, mediate its performance, and provide sufficient mechanical and chemical stability to enable integration of conjugated polymers into devices and microsystems.

NASA Discipline Life Support Systems↗

The Effect of Spaceflight on the Ultrastructure of the Cerebellum

In weightlessness, astronauts and cosmonauts may experience postural illusions as well as motion sickness symptoms known as the space adaptation syndrome. Upon return to Earth, they have irregularities in posture and balance. The adaptation to microgravity and subsequent re-adaptation to Earth occurs over several days. At the cellular level, a process called neuronal plasticity may mediate this adaptation. The term plasticity refers to the flexibility and modifiability in the architecture and functions of the nervous system. In fact, plastic changes are thought to underlie not just behavioral adaptation, but also the more generalized phenomena of learning and memory. The goal of this experiment was to identify some of the structural alterations that occur in the rat brain during the sensory and motor adaptation to microgravity. One brain region where plasticity has been studied extensively is the cerebellar cortex-a structure thought to be critical for motor control, coordination, the timing of movements, and, most relevant to the present experiment, motor learning. Also, there are direct as well as indirect connections between projections from the gravity-sensing otolith organs and several subregions of the cerebellum. We tested the hypothesis that alterations in the ultrastructural (the structure within the cell) architecture of rat cerebellar cortex occur during the early period of adaptation to microgravity, as the cerebellum adapts to the absence of the usual gravitational inputs. The results show ultrastructural evidence for neuronal plasticity in the central nervous system of adult rats after 24 hours of spaceflight. Qualitative studies conducted on tissue from the cerebellar cortex (specifically, the nodulus of the cerebellum) indicate that ultrastructural signs of plasticity are present in the cerebellar zones that receive input from the gravity-sensing organs in the inner ear (the otoliths). These changes are not observed in this region in cagematched ground control animals. The specific changes include the formation of lamellar bodies, profoundly enlarged Purkinje cell mitochondria, the presence of inter-neuronal cellular protrusions in the molecular layer, and signs of degeneration in the distal dendrites of the Purkinje cells. Since these morphologic signs are not apparent in the control animals, they are not likely to be due to caging or tissue processing effects. The particular nature of the structural alterations in the nodulus, most notably the formation of lamellar bodies and the presence of degeneration, further suggests that excitotoxicity (damaging overstimulation of neurons) may play a role in the short-term neural response to spaceflight. These findings suggest a structural basis for the neuronal and synaptic plasticity accompanying the central nervous system response to altered gravity and help identify the cellular bases underlying the vestibular abnormalities experienced by astronauts during periods of adaptation and re-adaptation to different gravitational forces. Also, since the short- and long-term changes in neural structure occurring during such periods of adaptation resemble the neuronal alterations that occur in some neurologic disorders such as stroke, these findings may offer guidance in the development of strategies for rehabilitation and treatment of such disorders.

Holstein, Gay R.↗

Overcoming the Damping–Elasticity Paradox via 3D‐Printed NiTiSn Nanocomposite

Abstract Developing high damping alloys (HDAs) with large elastic strain has attracted growing attention due to the increasing demand for energy absorption with overload reliability and reusability. However, damping capacity inherently conflicts with elasticity, because the former requires a liable movement of crystal defects while the latter opposite. To deal with the damping‐elasticity paradox, the advantage of pseudobinary eutectic reaction and rapid cooling of laser powder bed fusion is taken to fabricate a bulk NiTiSn nanocomposite with a two‐level hierarchical structure. The first‐level architecture is composed of martensitic NiTi nanolamellae and reinforced Ti 3 Sn nanolamellae. In addition to lattice strain matching and lamellar boundary strengthening, a novel mechanism of martensite reorientation mediated by reversible stress‐induced detwinning‐twinning is activated to generate large elastic strain. A high density of nanotwins and nanodomains within NiTi nanolamellae constitute the second‐level architecture, which provides pronounced internal friction for high damping capacity. As a result, our NiTiSn nanocomposite exhibits a record‐high integration of damping capacity (tanδ > 0.10) and elastic strain (exceeding 4.5%), as well as superb stability under cyclic overload. This research not only represents a major breakthrough in achieving HDAs with outstanding damping and elastic strain but also offers a novel paradigm for high‐performance functional and structural materials.

Chemistry↗

Electrochemically-Formed Disordered Rock Salt ω-Li x V 9 Mo 6 O 40 as a Fast-Charging Li-Ion Electrode Material

Electrochemically-formed disordered rock salt compounds are an emerging class of Li-ion electrode materials for fast-charging energy storage. However, the specific factors that govern the formation process and the resulting charge storage performance are not well understood. Here, we characterize the transformation mechanism and charge storage properties of an electrochemically-formed disordered rock salt from V 9 Mo 6 O 40 (VMO). The crystal structure of VMO has similar motifs to that of α-V 2 O 5 , a well-studied analogue, but VMO has less mechanical flexibility due to additional corner-sharing octahedra in its structure. As a result, VMO undergoes a single-step transformation pathway, which we characterize through operando X-ray diffraction, and forms an unusual highly distorted lamellar microstructure, as we show with high-resolution transmission electron microscopy. The resulting Li x VMO material shows fast charging and other electrochemical characteristics and performance typical of many nanomaterials, even though the material is composed of relatively large particles.

25 ENERGY STORAGE↗

Atomic-Scale Structure and Non-Stoichiometry of Meteoritic Hibonite: A Transmission Electron Microscope Study

Hibonite (CaAl_12O_19) is a common refractory mineral in Ca-Al-rich inclusions (CAIs) in primitive meteorites. Transmission electron microscope (TEM) studies have identified enigmatic planar defects in different occurrences of hibonite in the Allende meteorite that give rise to strong streaking along c* in electron diffraction patterns. Atomic resolution high-angle annular dark-field (HAADF) imaging and energy-dispersive X-ray (EDX) analyses were used to determine the nature and origin of these planar features. HAADF images of hibonite grains reveal lamellar intergrowths of common 1.6 nm spacing, and less commonly 2.0 and 2.5 nm spacings, interspersed in stoichiometric hibonite showing 1.1 nm (002) spacing. Stoichiometric hibonite consists of alternating Ca-containing (“R”) and spinel-structured (“S”) blocks stacked in a sequence RS. In contrast, the 1.6 nm layers result from a doubled S block such that the stacking sequence is RSS, while in the widest defect observed, the stacking sequence is RSSSS. These intergrowths are epitaxial and have coherent, low-strain boundaries with the host hibonite Meteoritic hibonite shows common Ti and Mg substitution for Al in its structure. Atomic-resolution EDX maps of hibonite grains in the Allende CAI confirm the preferred site occupancy of Mg on tetragonal M3 sites in S blocks and of Ti on trigonal bipyramidal M2 and octahedral M4 sites in R blocks. Mg is highly concentrated, but Ti is absent in the planar defects where wider S blocks show Al-rich compositions compared to stoichiometric MgAl_2O_4 spinel. Therefore, Mg likely played the major role in the formation and metastability of planar defects in hibonite. Electron energy loss spectroscopy data from the Ti L_2,3 edge show the presence of mixed Ti oxidation states with ~ 15–20% of Ti as Ti^(3+) in hibonite, suggesting a direct substitution of Ti^(3+) ↔ Al^(3+) in hibonite. The remaining ~ 80–85% of Ti is present as Ti^(4+) and corresponding EDX analyses are consistent with the well-known coupled substitution 2Al^(3+) ↔ Ti^(4+) + Mg^(2+) being the major mechanism for Ti and Mg substitution in hibonite. The formation of planar defects in hibonite occurred during high-temperature nebular condensation or melting/crystallization processes. The occurrence of non-stoichiometric hibonite in the Allende CAI deviates from the mineral formation sequence predicted from equilibrium condensation models. Overall, our atomic resolution TEM observations signify non-equilibrium, kinetic-controlled crystal growth during the high-temperature formation of refractory solids in the early solar nebula.

hibonite↗

Effects of Minor Alloying Additions on the Microstructure, Toughness, and Creep Strength of Directionally Solidified NiAl-31Cr-3Mo

A study of the effects of small (0.25 to 1.0 at%) fifth element additions to the structure and mechanical properties of directionally solidified (DS) NiAl-31Cr-3Mo has been undertaken. Essentially all the additions changed the as-DS'ed microstructure from lamellar eutectic grains to cells and, in some cases, introduced NiAl dendrites and/or third phases. In general the alloying additions did not improve strength or toughness over that possessed by the base composition; only Hf and, perhaps Ti, gave a minor increase in elevated temperature creep resistance. The lack of improvement in creep properties is probably due to inability to precipitation harden NiAl.

Whittenberger, J. D.↗

Effects of Polymer Morphology on Solvent and Catalyst Accessibility during Polyethylene and Polystyrene Autoxidation

Efficient catalytic deconstruction of plastics requires facile solvent and catalyst access to polymer substrates to minimize mass transfer effects. Autoxidation using Co(II) acetate, Mn(II) acetate, and a radical carrier in acetic acid is a promising strategy to deconstruct mixed plastic waste, yet the role of polymer morphology in governing solvent and catalyst accessibility remains poorly understood. Here, in situ simultaneous small- and wide-angle X-ray scattering (SAXS/WAXS), complemented by X-ray fluorescence (XRF) imaging and high-pressure differential scanning calorimetry (DSC), were used to elucidate interactions between acetic acid, a Co/Mn catalyst solution, and semicrystalline polyethylene (PE) and amorphous polystyrene (PS) from room temperature to 160 °C. In PE, acetic acid and catalyst access were confined to amorphous regions and cryomilled particle interfaces at room temperature, while crystalline lamellae remained intact after soaking for up to 34 h. Increasing temperature enabled solvent uptake into PE, followed by solvent-assisted softening above 100 °C, and a modest melting-point depression that removed lamellar transport barriers upon melting. Conversely for PS, acetic acid penetrated the glassy polymer without inducing chain mobility until the glass transition was reached, above which the observed structural changes were consistent with enhanced segmental mobility which enabled bulk penetration. These results suggest that polymer morphology and thermally activated physical transitions arising from diffusion and polymer–solvent interactions can influence whether autoxidation of plastics is transport-limited or kinetically controlled, providing a framework for aligning reaction conditions with reaction outcomes.

09 BIOMASS FUELS↗

Influence of convection of spiral structures in lead-tin eutectic

Convection was generated during directional solidification by the accelerated crucible rotation technique (spin up/spin down). This stirring increased the rotation rate of the microstructure and reduced the length solidifying cooperatively, but had no influence on the lamellar spacing.

Popov, Dimitar↗

Impact of surface hydrophilicity on the ordering and transport properties of bicontinuous microemulsions

Microemulsions (MEs) have many industrial applications, where recent developments have shown that MEs can be utilized for electrochemical applications, including potentially in redox flow batteries. However, understanding the structure and dynamics of these systems, including at a surface, is needed to direct and rationally control their electrochemical behavior. While bulk solution measurements have provided insight into their structure, their assembly at an interface also impacts the electron (to the electrode) and ion (across the surfactant) charge transfer processes in the system. To address this shortcoming, neutron reflectivity experiments and molecular simulations have been completed that document the near surface structure of a series of deuterated water (D 2 O)/polysorbate-20/toluene MEs on hydrophilic and amphiphilic surfaces. These results show that the microemulsions form complex layered structures near a hard electrode surface, where most layers are not purely one component. Decreasing the D 2 O concentration in the ME increases the number of and purity of the layers established on the solid surface. These lamellar-type layers transition from the surface to the bulk microemulsion as a series of mixed layers (i.e., containing oil, water, and surfactant) that are consistent with perforated lamellae. Additionally, these mixed lamellae appear to become more perforated with oil and water pathways on an amphiphilic surface. Furthermore, the purity and thickness of these layers will influence the accessibility of an electrode by redox active species, as well as ion transport required to satisfy the electroneutrality condition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Anion-dependent phase behavior of methylimidazolium-based ionic liquids mixed with water: Correlation between local molecular structure and mesoscale behaviors

The mesoscopic phase behavior of decylmethylimidazolium (C 10 mim) ionic liquids (ILs) bearing three monovalent anions—thiocyanate (SCN − ), nitrate (NO 3 − ), and chloride (Cl − )—mixed with water at relatively high IL contents (50–95 wt%) was investigated. Small-angle and wide-angle X-ray scattering (SAXS/WAXS) were employed to follow the evolution of both local and mesoscale structures across this composition range. In the absence of water, C 10 mimSCN and C 10 mimCl behaved as disordered liquids, whereas C 10 mimNO 3 spontaneously formed a hexagonally ordered cylindrical mesophase and displayed a sticky-solid macroscopic appearance. Upon addition of water, C 10 mimSCN remained a viscous liquid and only weakly ordered lamellar domains were observed. This limited ordering is attributed to the lack of hydrogen bonding and weak interaction energy between SCN − anions and C 10 mim + cations. In contrast, the trigonal-planar NO 3 − and point-like Cl − anions promoted the formation of well-defined hexagonal mesophases up to 35–45 wt% water. The formation of hydrogen bonding of the two anions with imidazolium ring protons likely enabled the creation of compact ion clusters that effectively exclude water molecules from the immediate vicinity of the IL aggregates. These findings demonstrate that the interaction energy between ion pairs dictate IL-water interactions and therefore control the transition from disordered liquids to ordered mesophases in IL/water mixtures with high IL contents. In conclusion, the combined SAXS/WAXS analysis reveals a correlation between local intermolecular structure and the emergence of mesoscopic order, providing a systematic framework for tailoring mesoscale structures in alkylimidazolium-based IL/water systems.

36 MATERIALS SCIENCE↗

Lamellar olivine in the Divnoe achondrite: Evidence for high-pressure exsolution?

The olivine-rich Divnoe achondrite contains numerous large olivine grains which have a lamellar or banded appearance in back-scattered electron images, caused by minor compositional differences. One such grain, viewed in transmitted light, displays a system of lamellae with the same orientation and scale as the compositional banding. The only process known to produce such structure and chemical variability in olivine grains is high-pressure transformations between alpha-, beta- and gamma-olivines, but in other meteorites and in experimental products the structure is approximately 100 times finer than the Divnoe lamella.

Petaev, M. I.↗

A twist grain boundary phase in aqueous solutions of the nucleic acid tetramer GTAC

At high concentration, long Watson/Crick (WC) double-helixed DNA forms columnar crystal or liquid crystal phases of linear, parallel duplex chains packed on periodic lattices. This can also be a structural motif of short NA oligomers such as the 5’-GTAC-3’ studied here, which makes four-base WC duplexes having hydrophobic blunt ends. End-to-end aggregation then assembles these duplexes into columns and columnar phases are stabilized, in spite of breaks in the double helix every four bases. But the new degrees of freedom introduced by such breaks also enable opportunities for a more diverse palette of self-assembly modes, producing striking self-assemblies of DNA that would not be achievable with contiguous polymers. These include recently reported three-dimensional (3D) periodic low-density nanoscale networks of GCCG, and the twist grain boundary (TGB) phase presented here. In the TGB, columns of GTAC pairs assemble into monolayer sheets in which the duplex columns are mutually parallel. However, unlike in the columnar crystals, these sheets stack in helical fashion into lamellar arrays in which the column axis of each layer is rotated through a 60° angle with respect to the columns in neighboring layers. This assembly of DNA is unique in that it the fills a 3D volume wherein the major grooves of columns in each layer mutually enter and interlock with the major grooves of columns in neighboring layers. This locking is optimized by small adjustments in structure enabled by the breaks in the duplex backbones.

DNA↗

Assessment of binary eutectic Ni alloys for high-temperature applications via laser remelting

It has been recently demonstrated that eutectic alloys processed by additive manufacturing have excellent high-temperature mechanical properties. We suggest that nickel-base eutectic alloys may enable new combinations of structural and functional properties. To this end, we investigate the processability, microstructure, and thermal stability of five, binary near-eutectic Ni-X (X = B, Ce, La, Y, and Zr) alloys processed via surface laser-remelting. The microstructure of all alloys contain a two-phase lamellar eutectic microstructure consisting of γ-Ni and intermetallic phases; this microstructure is significantly finer (100–200 nm lamellar spacing) in the laser-remelted alloys than in the cast substrate (0.5–1.0 µm lamellar spacing). The microhardness of the laser-remelted alloys (550–770 HV) is 35–50% higher than that of the cast alloys (370–570 HV) due to this finer eutectic spacing. An anomalous eutectic microstructure appears at the meltpool boundaries, containing globular and lamellar γ-Ni phases. The alloys contain a high volume fraction (>50 vol%) of intermetallic phase which forms a continuous network, causing brittleness. Following laser-remelting trials, the alloys showed a high density of solid-state cracks, except for the Ni-Zr alloy which processed well. During thermal exposure at 700 and 900°C for up to 500 h, the eutectic microstructure coarsens. Coarsening occurs heterogeneously and initiates at the meltpool boundaries. This process occurs more slowly in the Ni-Zr and Ni-Y alloys, and more rapidly in the remaining alloys, resulting in greater microhardness retention in the Ni-Zr and Ni-Y alloys following thermal exposure at 700°C. Thus, among the five alloys, the Ni-Zr system exhibits a good combination of high-temperature mechanical properties and processability. Here, we conclude with recommendations for future work on designing additively manufactured alloys based on these eutectic Ni systems.

Additive manufacturing↗

Directional solidification of Al2-Cu-Al and Al3-Ni-Al eutectics during TEXUS rocket flight

One lamellar eutectic sample and one fiber-like eutectic sample were solidified directionally during the TEXUS-6 rocket flight. The microstructures and the results of the thermal analysis, obtained from the temperatures recorded on the cartridge skin, are compared. No appreciable modifications of the regularity of the eutectic structures were observed by passing from 1 g to 0.0001 g in these experiments. No steady state growth conditions were achieved in these experiments.

Favier, J. J.↗