Search NASA⌕ Search

SEARCH · Search NASA

Results for “lateral force”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Wind-tunnel/flight correlation study of aerodynamic characteristics of a large flexible supersonic cruise airplane CXB-70-1). 1: Wind-tunnel tests of a 0.03-scale model at Mach numbers from 0.6 to 2.53

The longitudinal and lateral forces and moments for a 0.03 scale deformed rigid, static force model of the XB-70-1 airplane were determined. Control effectiveness was determined for the elevon in pitch and roll, for the canard, and for the rudders. Component effects of the canard, deflected with tips, variable position canopy, bypass doors, and bleed dump fairing were measured. The effects of small variations in inlet mass flow ratio and small amounts of asymmetric deflection of the wing tips were assessed.

Daugherty, J. C.↗
NASA NTRS1982

Measurement and evaluation of swirl-type flow in labyrinth seals of conventional turbine stages

The effects of load factor and rotor eccentricity were determined on flow conditions in test series for two stages. The results indicate that swirl-type entry flow follows the rules of potential swirl. Within the labyrinth cavities two spatial separated flow areas are considered. A dominating flow in periphera direction nearly fills the space between the sealing strips and the ceiling of the cavity. Below this flow, an area of axial mass transport is situated, with a slight peripheral component, limited on the nearest surroundings of the seals gap and the rotor surface. Between both flows, an exchange of energy takes place. Within the gaps, flow direction depends on axial velocity and therefore on variable flow contraction. A balance of energy within the seal and the cavities interprets the results of lateral force measurements as an influence of friction at the sealing strips surface and the rotating shaft surface. Stages with their blades put together in buckets by means of shrouding segments are particularly influenced by the rotating speed of the shrouding.

Hauck, L.↗
NASA NTRS1984

Flow processes in overexpanded chemical rocket nozzles. Part 2: Side loads due to asymmetric separation

Methods for measuring the lateral forces, occurring as a result of asymmetric nozzle flow separation, are discussed. The effect of some parameters on the side load is explained. A new method was developed for calculation of the side load. The values calculated are compared with side load data of the J-2 engine. Results are used for predicting side loads of the space shuttle main engine.

Schmucker, R. H.↗
NASA NTRS1988

An exactly solvable model for calculating critical misfit and thickness in epitaxial superlattices. II - Layers of unequal elastic constants and thicknesses

The theoretical model developed by van der Merwe and Jesser (1988) is extended to permit the exact determination of the critical misfit and critical thickness of an epitaxially grown superlattice made up of layers with differing elastic constants and thicknesses. Lateral force balances are maintained by means of an explicit relationship between the homogeneous misfit strains and the thicknesses and moduli. A number of simplifying approximations are introduced, and sample numerical results are presented in graphs.

Jesser, W. A.↗
NASA NTRS1991

High alpha aerodynamic control by tangential fuselage blowing

This work explores the effect of tangential blowing on the vortical structures that develop around a tangent-ogive cylinder configuration at high angle of attack. A lateral force results if blowing is applied asymmetrically. The study is conducted numerically by solving the three-dimensional, compressible-flow Navier-Stokes equations. The computation was done for a Reynolds number of 52,000, Mach number of 0.2, blowing momentum coefficients of 0.0, 0.1, 0.2, and 0.4, and angle of attack of 10, 30, and 45 deg. Only asymmetrical blowing was considered. Surface streamlines, helicity contours and pressure distributions are obtained for each case.

Font, G. I.↗
NASA NTRS1949

Investigation at low speeds of the effect of aspect ratio and sweep on rolling stability derivatives of untapered wings

A low scale wind tunnel investigation was conducted in rolling flow to determine the effects of aspect ratio and sweep (when varied independently) on the rolling stability derivatives for a series of untapered wings. Test results indicate that when the aspect ratio was held constant, an increase in the sweepback angle caused a significant reduction in the damping in roll at low lift coefficients for only the higher aspect ratios that were tested. This result was in agreement with available swept wing theory which indicated no effect of sweep for aspect ratios near zero. The result of the linear theory that the damping in roll is independent of lift coefficient and that the yawing moment and lateral force due to rolling are directly proportional to the lift coefficient was found to be valid for only a very limited lift coefficient range when the wings were highly swept. For such wings, the damping was found to increase in magnitude and the yawing moment due to rolling, to change from negative to positive at moderate lift coefficients. The effect of wing tip suction, not acounted for by present theory, was found to be very important with regard to the yawing moment due to rolling, particularly for low aspect ratio swept wings. An empirical means of correcting present theory for the effect of tip suction is suggested.

Goodman, Alex↗
NASA NTRS1922

Causes of failure of airship shed

The causes of the collapse of airship shed, which was being taken down at Niediergorsdorf, are discussed. This shed, which was built of iron, was 184 m long, 28 m high, and 35 m wide. The demolition of the shed had been assigned to unskilled men who proceeded to remove certain key structural supports, leaving the structure in such a condition that relatively small eccentricities of the columns or spans or of lateral forces could easily have caused the columns or spans to break down. A small gust of wind would have perhaps sufficed to bring the building down. An analysis is also given of the suction effects on the roof of an air shed in Staaken. The damage to this shed, which occurred during a storm, was due to the fact that the shed had no opening in its top for equalizing the air pressure within and without. The location of the plates blown off the roof correspond to the point of greatest suction.

Sonntag, R↗
NASA NTRS1940

Wind Tunnel Investigation of Fuselage Stability in Yaw with Various Arrangements of Fins

An investigation was made in the 7-by-10 foot wind tunnel to determine the effects of dorsal-type fins and various arrangements of fins on the aerodynamic characteristics of a streamline circular fuselage. Comparative plots of the aerodynamic characteristics of the fuselage alone and the fuselage with various fin arrangements are given to show their effects on coefficients of yawing moment, drag, and lateral force. Results are also given for one case in which a rear fin on a circular fuselage was faired with modeling clay to obtain a fuselage shape with the same side elevation as the fuselage with the unfaired fin but with an elliptical cross section over the rearward portion of the fuselage. The results indicated that fin area to the rear of the center of gravity of the fuselage was beneficial in reducing the magnitude of the unstable yawing moments at large angles of yaw; whereas, fin area forward of the center of gravity was harmful. The dorsal-type fin was more effective for increasing the yawing stability of the fuselage than was a smoothly faired rearward portion with the same side elevation as the fuselage with the unfaired dorsal type fin. The minimum drag coefficient and the slope of the curve of yawing-moment coefficient of the fuselage at zero yaw were unaffected by the addition of the fins, within the experimental accuracy of the tests.

Hoggard, H Page, Jr↗
NASA NTRS1947

Wind-Tunnel Investigation of Effects of Unsymmetrical Horizontal-Tail Arrangements on Power-on Static Longitudinal Stability of a Single-Engine Airplane Model

A wind-tunnel investigation has been made to determine the effects of unsymmetrical horizontal-tail arrangements on the power-on static longitudinal stability of a single-engine single-rotation airplane model. Although the tests and analyses showed that extreme asymmetry in the horizontal tail indicated a reduction in power effects on longitudinal stability for single-engine single-rotation airplanes, the particular "practical" arrangement tested did not show marked improvement. Differences in average downwash between the normal tail arrangement and various other tail arrangements estimated from computed values of propeller-slipstream rotation agreed with values estimated from pitching-moment test data for the flaps-up condition (low thrust and torque) and disagreed for the flaps-down condition (high thrust and torque). This disagreement indicated the necessity for continued research to determine the characteristics of the slip-stream behind various propeller-fuselage-wing combinations. Out-of-trim lateral forces and moments of the unsymmetrical tail arrangements that were best from consideration of longitudinal stability were no greater than those of the normal tail arrangement.

AIRFOILS - NACA 65(216-012(MOD ) - CHAR & MOMENTS ↗
NASA NTRS1952

Investigation of the Influence of Fuselage and Tail Surfaces on Low-speed Static Stability and Rolling Characteristics of a Swept-wing Model

Results are presented of a wind-tunnel investigation to determine influence of the fuselage and tail on static stability and rotary derivatives in roll of a model having 45 degrees sweptback wing and tail surfaces. The wing alone and the model without the horizontal tail showed marginal longitudinal stability near maximum lift. The longitudinal stability of the complete model was satisfactory. The vertical tail produced larger increments of rate of change of lateral-force and yawing-moment coefficients with wing-tip helix angle than the fuselage or the horizontal tail.

TAIL-WING-FUSELAGE COMBINATIONS - AIRPLANES↗
NASA NTRS1941

Wind-tunnel investigation of effect of interference on lateral-stability characteristics of four NACA 23012 wings, an elliptical and a circular fuselage and vertical fins

Report presents the results of a wind-tunnel investigation of the effect of wing-fuselage interference on lateral-stability characteristics made in the NACA 7 by 10-foot wind tunnel on four fuselages and two fins, representing high-wing, low-wing, and midwing monoplanes. The fuselages are of circular and elliptical cross section. The wings have rounded tips and, in plan form, one is rectangular and the three are tapered 3:1 with various amounts of sweep. The rate of change in the coefficients of rolling moment, yawing moment, and lateral force with angle of yaw is given in a form to show the increment caused by wing-fuselage interference for the model with no fin and the effect of wing-fuselage interference on fin effectiveness. Results for the fuselage-fin combination and the wing tested alone are also given.

House, Rufus O↗
NASA NTRS1954

Determination of the elastic constants of airplane tires

For determination of the elastic constants of airplane tires which are required for the numerical calculations of the shimmy properties of nose and tail wheels, deformation measurements were carried out on four different tires. For this purpose, the tires were loaded in each case with a normal load and then with a lateral force, a tangential force, and a moment. Moreover, the weight and the mass moment of inertia about a vertical axis were determined for the various tires.

TIRES↗
NASA NTRS1995

Program For Simulating Dynamics Of Aerospace Vehicles

SORT (Simulation and Optimization of Rocket Trajectories) is general-purpose three-degree-of-freedom with three axis static moment balance simulation of flight dynamics of arbitrary aerospace vehicle. Modular structure facilitates application to variety of trajectory-analysis problems. Contains math model of aerodynamics completely generalized. Computes both longitudinal and lateral forces and moments. In addition to fore-body coefficients, computes longitudinal base effect aerodynamic forces and moments. Simplified ballistic-coefficient model also available for analysis of ballistic entry. Written using ANSI FORTRAN 77.

Berning, M. J.↗
NASA NTRS2000

Geometric Perturbations and Asymmetric Vortex Shedding about Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approx. = 40 deg.), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approx. = 60 deg.), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90 deg., the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40 deg. and alpha = 60 deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60 deg. which is consistent with the application of a tip bump, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft. portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40 deg., and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗
NASA NTRS2000

Geometric Perturbations and Asymmetric vortex shedding About Slender Pointed Bodies

The flow about slender, pointed bodies can be characterized by different states with angle of attack. At moderate-to-high angles of attack (alpha approximately equals 40deg), a steady, asymmetric vortex pattern develops along the body, leading to a net lateral force. At higher angles of attack (alpha approximately equals 60deg), the aft-end of the body develops an unsteady von Karman shedding. As the angle of attack approaches 90deg, the entire body length exhibits a time-dependent vortex shedding pattern. The current work uses three-dimensional, thin-layer Navier-Stokes simulations to investigate the physical mechanisms of asymmetric vortex shedding at alpha = 40deg and alpha = 60deg. The development of an asymmetric vortex pattern via a convective instability mechanism is investigated using tip bumps, surface roughness, and tip curvature. It's found that surface roughness simulations can incite an asymmetric vortex state at alpha = 60deg which is consistent with the application of a tip bumps, and the experimentally observed flowfield. The unsteady von Karman vortex shedding on the aft portion of the body is also well resolved. The use of surface roughness did not incite a flow asymmetry at alpha = 40deg, and it was necessary to simulate tip curvature at this angle of attack in order to generate an asymmetric vortex state.

Murman, Scott M.↗
NASA NTRS1946

Effect of an Auxiliary Belly Fuel Tank on the Low-Speed Static Stability Characteristics of a 1/5-Scale Model of the Grumman XF8F-1 Airplane, TED No. NACA 2384

In.order to determine the aerodynamic effects of an auxiliary belly fuel tank on the Grumman F8F-1 airplane, a wind-tunnel investigation was made on a l/5 - scale model of the Grumman XF8F-1 airplane. Pitch and yaw tests were made with the model in the cruising and landing configurations for windmilling and take-off power conditions. Tuft studies and static-pressure measurements were also made to determine the flow characteristics in the region of the fuel tank. It was found that, at low speed, the auxiliary fuel tank test conditions, especially with power on in the landing configuration at high lift coefficients. The static directional stability was decreased for most test conditions, but the addition of a fairing between the fuselage and fuel tank improved the directional stability slightly in the power-on clean condition. The effective dihedral and lateral force were increased for most of the conditions tested. The tuft studies and pressure measurements indicated that the removal of the away braces would improve the.flow characteristics considerably in the region of the fuel tank end might also decrease the buffeting of the belly tank at high speeds.

Cook, Charles B.↗
NASA NTRS2008

Control System for Bearingless Motor-generator

A control system for an electromagnetic rotary drive for bearingless motor-generators comprises a winding configuration comprising a plurality of individual pole pairs through which phase current flows, each phase current producing both a lateral force and a torque. A motor-generator comprises a stator, a rotor supported for movement relative to the stator, and a control system. The motor-generator comprises a winding configuration supported by the stator. The winding configuration comprises at least three pole pairs through which phase current flows resulting in three three-phase systems. Each phase system has a first rotor reference frame axis current that produces a levitating force with no average torque and a second rotor reference frame axis current that produces torque.

Kascak, Peter E.↗