Search NASA⌕ Search

SEARCH · Search NASA

Results for “lattice parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An evaluation of tri-valent oxide (Cr 2 O 3 ) as a grain enlarging dopant for UO 2 nuclear fuels fabricated under reducing environment

A study was performed to evaluate the microstructure and crystallography of nominally 500–2000 Cr 2 O 3 -doped UO 2 fabricated in a temperature range of 1150–1750°C under reducing experimental conditions. We observed an increase in grain size of the samples with the increase in heat treating temperature as expected. For a given sintering temperature (1700–1750°C), an increase in the grain size was also observed with the increase in Cr 2 O 3 concentration up to a value of ~1000–1200 wppm. A decrease in fission gas release as a function of grain size was estimated for the Cr 2 O 3 -doped UO 2 samples assuming specified post-irradiation annealing conditions. A nearly linear decrease was obtained in the lattice parameter of the Cr 2 O 3 -doped UO 2 fcc phase with the increase in Cr 2 O 3 concentration, especially up to a nominal value of 1000 wppm. The lattice parameter decrease was also persistent with the increase in the average grain size as a result of addition of Cr 2 O 3 into the UO 2 lattice. An increase in the crystallite size and a decrease in the microstrain of the $fcc$ phase were observed with the increase in the average grain size of the samples, indicating a higher crystallinity of the Cr 2 O 3 -doped samples than that of the undoped UO 2 sample.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Ultrastable cathodes enabled by compositional and structural dual-gradient design

Cathodes for next-generation batteries are pressed for higher voltage operation (≥4.5 V) to achieve high capacity with long cyclability and thermal tolerance. Current cathodes fail to meet these requirements owing to structural and electrochemical strains at high voltages, leading to fast capacity fading. Here, in this work, we present a cathode with a coherent architecture ranging from ordered to disordered frameworks with concentration gradient and controllable Ni oxidation activities, which can overcome voltage ceilings imposed by existing cathodes. This design enables simultaneous high-capacity and high-voltage operation at 4.5 V without capacity fading, and up to 4.7 V with negligible capacity decay. Multiscale diffraction and imaging techniques reveal the disordered surface is electrochemically and structurally indestructible, preventing surface parasitic reactions and phase transitions. Structural coherence from ordering to disordering limits lattice parameter changes, mitigating lattice strain and enhancing morphological integrity. The dual-gradient design also notably improves thermal stability, driving the advancement of high-performance cathode materials.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Lattice Design and Advanced Modeling to Guide the Design of High-Performance Lightweight Structural Materials

Lightweight structural materials are required to increase the mobility of fission batteries. The materials must feature a robust combination of mechanical properties to demonstrate structural resilience. The primary objective of this project is to produce lightweight structural materials whose strength-to-weight ratios exceed those of the current widely used structural materials such as 316L stainless steels (316L SS). To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structures models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The preliminary results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison with the solid material and that the unit cell size of the lattice had a minimal effect. The novelty here is to apply up-front modeling to determine the best structure for the application before actually producing the sample. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for material development.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Thermal expansion behavior of NiSi/NiSi2

The thermal expansion of NiSi/NiSi2 for a range of temperatures from 293 to 1223 K was determined using high-temperature X-ray diffraction. While a linear relation with temperature was found for the lattice parameter of NiSi2, third-order relationships were found for the three lattice parameters of NiSi, with one of the parameters showing a decrease with increasing temperature. The volumetric expansion of both materials exhibited linear relationships.

Wilson, D. F.↗
DOE OSTI2025

Lattice Structured Lightweight Structural Materials

The development of lightweight structural materials is crucial for enhancing the performance and deployment feasibility of fission batteries. This study aims to produce lightweight structural materials whose strength-to-weight ratios exceed those of current widely used structural materials. To achieve this, advanced modeling and simulation tools were employed to design lattice structures with different lattice parameters and different lattice types. A process was successfully developed for transforming lattice-structured models into Multiphysics Object Oriented Simulation Environment (MOOSE) inputs. Finite element modeling (FEM) was used to simulate the uniaxial tensile testing of the lattice-structured parts to investigate the stress distribution at a given displacement. The modeling results showed that the lattice-structured sample displayed a lower Young’s modulus in comparison to the solid material; the increase in solid shell thickness and blend radius enhances the mechanical performance; and the effect of unit cell size on macro scale stress is minimal. Tensile testing was conducted on the solid and lattice-structured materials fabricated by laser powder bed fusion (LPBF) additive manufacturing. The experimental results agreed well with the model prediction. The approach of using modeling as a guiding tool for preliminary material design can significantly save time and cost for new material development.

lightweight material↗
DOE OSTI2026

Thermal Stability of LiNi x Mn y Co z O 2 Cathode Materials

Here, the thermal evolution of LiNi x Mn y Co z O 2 (NMC) lithium-ion battery electrode materials is examined at various states of charge (SOC) or lithium concentrations for a variety of Ni:Mn:Co ratios or electrode compositions. Synchrotron X-ray diffraction (XRD) combined with Rietveld analysis shows the onset decomposition temperatures of phases, decomposition products, lattice parameters, and phase fractions as a function of composition and SOC. SOC impacts the lattice parameters of the NMC phase, where a collapse of the c-axis in the NMC phases is noted due to lithium extraction. Among the compositions examined, the low-Ni NMC111 uncycled sample (NMC111 0% SOC) exhibited the highest thermal stability, with a decomposition temperature approximately 250 °C higher than that of NMC532 0% and NMC811 0%. When the SOC exceeds 50% (i.e., more than 0.4 mol of Li ions extracted), the influence of Ni content on the decomposition temperature becomes negligible, with decomposition occurring around 250−300 °C for all compositions. Ni content also affects the decomposition pathways: NMC111 tends to first form a TM 3 O 4 -type phase, where TM represents transition metals, before transforming into a TMO-type phase, whereas most of the NMC811 samples directly decompose into the TMO phase. The presence of metallic phases was confirmed by both XRD and thermogravimetric-differential scanning calorimetry (TGA-DSC) analysis, as a result of heating under inert conditions. The TGA-DSC results suggest that metallic phase formation is favored at lower SOC in samples with a higher Ni content. This work provides comprehensive insight into the thermal degradation pathways of NMC materials as a function of composition, SOC, and temperature.

Peng, Jian [Univ. of New South Wales, Sydney, NSW ↗
DOE OSTI2025

Shear strength of a refractory high entropy alloy MoNbTaVW under high pressure

Radial X-ray diffraction (R-XRD) was performed in situ using a Panoramic Diamond Anvil Cell on the refractory high entropy alloy MoNbTaVW. The lattice parameters were determined through a Le Bail fit using a body centered cubic (BCC) lattice of symmetry $Im$$\overline{3}$$m$ (international space group number 229). Upper and lower bounds to the shear strength were determined up to 80 GPa nonhydrostatically using copper as a pressure standard. The equation of state was derived at the magic angle ψ = 54.7° and yielded a bulk modulus of K 0 = 220.8 ± 1.65 GPa. The experimental lattice parameters and bulk modulus match closely with corresponding density functional theory (DFT) calculations. The BCC phase remains stable up to the highest pressure of 80 GPa studied and is shown to be elastically anisotropic. The shear strength was found to saturate around 70 GPa with a value of τ = 1.75 GPa, and the shear moduli are presented in different limits of iso-strain and iso-stress.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Low-temperature magnetic structure and lattice response in SmCuAs 2

We investigated the structural and magnetic properties of single-crystalline SmCuAs 2 using high-resolution synchrotron x-ray diffraction and x-ray resonant magnetic scattering (XRMS) at the Sm 𝐿 2 and 𝐿 3 edges. Temperature-dependent diffraction measurements confirm that SmCuAs2 maintains its tetragonal symmetry from room temperature down to 8 K, with lattice parameters showing anomalous behavior below the resistivity minimum (𝑇≈30K). Notably, the c-axis lattice parameter exhibits a plateau and subsequent increase near the Néel temperature, indicating magnetoelastic coupling. XRMS measurements reveal a commensurate antiferromagnetic structure with a propagation vector 𝒒=(0,0,0.5). Our measurement shows that the Sm moments are aligned within the 𝒂𝒃 plane and arranged in a ++−− stacking along the 𝒄 axis. Comparison with related 𝑅⁢𝐸⁢CuAs 2 compounds (RE = Pr, Nd, and Gd) suggests that in-plane moment orientation and associated magnetic frustration play a key role in the emergence of the resistivity minimum. Differences in spin-orbit and magnetoelastic coupling across the series highlight their importance in governing low-temperature transport behavior.

36 MATERIALS SCIENCE↗
NASA NTRS1996

Defect Structure of Beta NiAl Using the BFS Method for Alloys

The semiempirical BFS method for alloys is generalized by replacing experimental input with first-principles results thus allowing for the study of complex systems. In order to examine trends and behavior of a system in the vicinity of a given point of the phase diagram a search procedure based on a sampling of selected configurations is employed. This new approach is applied to the study of the beta phase of the Ni-Al system, which exists over a range of composition from 45-60 at.% Ni. This methodology results in a straightforward and economical way of reproducing and understanding the basic features of this system. At the stoichiometric composition, NiAl should exist in a perfectly ordered B2 structure. Ni-rich alloys are characterized by antisite point defects (with Ni atoms in the Al sites) with a decrease in lattice parameters. On the Al-rich side of stoichiometry there is a steep decrease in lattice parameter and density with increasing Al content. The presence of vacancies in Ni sites would explain such behavior. Recent X-ray diffraction experiments suggest a richer structure: the evidence, while strongly favoring the presence of vacancies in Ni sites, also suggests the possibility of some vacancies in Al sites in a 3:1 ratio. Moreover, local ordering of vacant sites may be preferred over a random distribution of individual point defects.

Bozzolo, Guillermo↗
NASA NTRS2002

Atomistic Modeling of RuAl and (RuNi) Al Alloys

Atomistic modeling of RuAl and RuAlNi alloys, using the BFS (Bozzolo-Ferrante-Smith) method for alloys is performed. The lattice parameter and energy of formation of B2 RuAl as a function of stoichiometry and the lattice parameter of (Ru(sub 50-x)Ni(sub x)Al(sub 50)) alloys as a function of Ni concentration are computed. BFS based Monte Carlo simulations indicate that compositions close to Ru25Ni25Al50 are single phase with no obvious evidence of a miscibility gap and separation of the individual B2 phases.

Gargano, Pablo↗
DOE OSTI2023

Synthesis and Thermal Oxidation Resistance of Boron-Rich Boron–Carbide Material

A boron-rich boron–carbide material (B4+δC) was synthesized by spark plasma sintering of a ball-milled mixture of high-purity boron powder and graphitic carbon at a pressure of 7 MPa and a temperature of 1930 °C. This high-pressure, high-temperature synthesized material was recovered and characterized by X-ray diffraction, X-ray photoelectron spectroscopy, Raman spectroscopy, Vickers hardness measurements, and thermal oxidation studies. The X-ray diffraction studies revealed a single-phase rhombohedral structure (space group R-3m) with lattice parameters in hexagonal representation as a = 5.609 ± 0.007 Å and c = 12.082 ± 0.02 Å. The experimental lattice parameters result in a value of δ = 0.55, or the composition of the synthesized compound as B4.55C. The high-resolution scans of boron binding energy reveal the existence of a B-C bond at 188.5 eV. Raman spectroscopy reveals the existence of a 386 cm−1 vibrational mode representative of C-B-B linear chain formation due to excess boron in the lattice. The measured Vickers microhardness at a load of 200 gf shows a high hardness value of 33.8 ± 2.3 GPa. Thermal gravimetric studies on B4.55C were conducted at a temperature of 1300 °C in a compressed dry air environment, and its behavior is compared to other high-temperature ceramic materials such as high-entropy transition metal boride. The high neutron absorption cross section, high melting point, high mechanical strength, and thermal oxidation resistance make this material ideal for applications in extreme environments.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Disorder-induced magnetoelastic behaviors of MnTexSbyBi1-x-y alloys

This dataset contains input and output files from density functional theory (DFT) simulations used to study the disorder-induced magnetoelastic behaviors of MnTexSbyBi1-x-y (0 ≤ x + y ≤ 1) alloys and their binary end members MnTe, MnSb, and MnBi. The alloys adopt the hexagonal NiAs-type (nickeline) structure and span ternary (MnTexSb1-x, MnTexBi1-x, MnBixSb1-x), and quaternary compositions across the full MnTe–MnSb–MnBi composition triangle. For each alloy composition, the dataset provides DFT calculations in three magnetic configurations: A-type antiferromagnetic (AFM), C-type AFM, and ferromagnetic (FM). Every magnetic configuration folder contains the fully relaxed crystal structure (CONTCAR), VASP input parameters (INCAR), and the main VASP output file (OUTCAR), from which total electronic energies, Mn magnetic moments, lattice parameters, and percent volume changes between magnetic states are extracted. These data are used to construct compositional phase diagrams, evaluate thermodynamic stability (formability), and map magnetoelastic responses across the alloy space. For A-type AFM and FM configurations, additional data are provided as follows: (i) FORCE_CONSTANTS and thermal_properties.yaml files at the top level of A-type_AFM/ and FM/ folders — present only for compositions marked with an asterisk (*) in Table I of the main text. These are derived from Phonopy finite-displacement calculations on full disordered 128-atom supercells and provide vibrational free energy, entropy (Svib)contribution from explicit disorder calculations. (Table I of the associated main manuscript) (ii) A VCA/ subfolder within A-type_AFM/ and FM/, containing FORCE_CONSTANTS and thermal_properties.yaml from Virtual Crystal Approximation phonon calculations (without spin-orbit coupling). VCA data are available for all compositions and are used to estimate vibrational contributions to the Gibbs free energy across the full composition space. (iii) A SOC/ subfolder containing CONTCAR, INCAR, and OUTCAR from spin-orbit coupling calculations, providing relativistic corrections to electronic energies and lattice parameters (Tables S2–S3 of the SM, and Table I of the main manuscript). (iv) A SOC/VCA/ subfolder containing FORCE_CONSTANTS and thermal_properties.yaml from VCA phonon calculations performed within the SOC framework, combining relativistic and vibrational thermodynamic corrections. The computed properties are used to map the AFM–FM magnetic crossover near MnTe0.75Sb0.25, demonstrate disorder- and spin-induced phonon broadening, identify a semiconductor-to-metal crossover, and quantify the pronounced magnetoelastic volume response near the magnetic phase boundary.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Performance and properties evolution of near-term accident tolerant fuel: Cr-doped UO 2

Chromium-doped UO 2 fuel has received significant interest due to the ability for chromium to produce pellets with large average grain size (>30 μm), which has shown to increase fission gas retention during operation. Sintering of chromium-doped UO 2 pellets was pursued with oxygen potential and sintering atmosphere controlled to tailor the final microstructure of the material. Chromium additions in this study ranged from 750 to 7800 ppm. Cr concentrations were studied pre and post sintering using Inductively Coupled Plasma Optical Emission Spectroscopy (ICP-OES). Effects of chromium content on lattice parameter and microstructure were examined with X-ray diffraction (XRD) and scanning electron microscopy (SEM). Contraction of the UO 2 lattice parameter was observed, as well as enlargement of grain size with increasing chromium content up to 4900 ppm Cr 2 O 3 . In addition, SEM indicated Cr incorporation within the matrix and the formation of chromium oxide precipitates throughout the microstructure at high Cr concentrations. Evaluation of thermophysical properties of Cr-doped UO 2 pellets were conducted up to 1200 °C to illustrate their evolution with increased dopant concentration and microstructural changes. The results show that grain size is maximized at 52 μm with Cr 2 O 3 concentration equal to 4900 ppm; however, grain size decreases at higher Cr 2 O 3 concentrations. No significant changes were observed in specific heat capacity, linear thermal expansion, and coefficient of thermal expansion compared to undoped UO 2 . The thermal conductivity also decreased through the incorporation of Cr 2 O 3 dopants above 750 ppm and is shown to be ~15 % lower than reported UO 2 values.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Reversible Oxidation Quantified by Optical Properties in Epitaxial Fe2CrO4+d Films on (001) MgAl2O4

We report on the structural and optical properties of Fe2CrO4+d epitaxial films grown by molecular beam epitaxy on MgAl2O4 (001) as a function of ?. The average Fe valence can be correlated with the out-of-plane lattice parameter and the extent of light absorption in the infrared spectral region. Over-oxidized films (0 < d < 0.5) exhibit reduced lattice parameters and suppressed infrared absorption. We discuss the behavior of a novel infrared transition at ~0.6 eV in stoichiometric Fe2CrO4 films deposited on MgAl2O4 (MAO) at or above 400 °C. This research provides new insight into the atomic structure, optical processes, oxidation states, electronic structure, and application potentials of Fe2CrO4+d.

ellipsometry, Epitaxy, thin film, oxidation, reduc↗
NASA NTRS1982

MC carbide structures in M(lc2)ar-M247

The morphologies and distribution of the MC carbides in Mar-M247 ingot stock and castings were investigated using metallographic, X-ray diffraction and energy-dispersive X-ray analysis techniques. The MC carbides were found to form script structures during solidification. The script structures were composed of three distinct parts. The central cores and elongated arms of the MC carbide script structures had compositions (Ti, Cr, Hf, Ta, W)C and lattice parameters of 4.39 A. The elongated script arms terminated in enlarged, angular "heads". The heads had compositions (Ti, Hf, Ta, W)C and lattice parameters of approximately 4.50 A. The heads had a higher Hf content than the cores and arms. The size of the script structures, as well as the relative amount of head-type to core and arm-type MC carbide, was found to be determined by solidification conditions. No carryover of the MC carbides from the ingot stock to the remelted and cast material was observed.

Wawro, S. W.↗
DOE OSTI2024

Effect of XC functionals and dispersion corrections on the DFT‐computed structural and vibrational properties of SrCl 2 –NaCl and ZrF 4 –LiF

Density functional theory (DFT) calculations were performed to examine the impact of exchange–correlation (XC) functionals and van der Waals corrections (specifically the D3 method) on the structural and vibrational properties of the SrCl 2 –NaCl and ZrF 4 –LiF salt systems. Multiple XC functionals, including the local density approximation (LDA), the generalized gradient approximation using the Perdew–Burke–Ernzerhof (PBE) model, and its modified form suitable for solids (PBEsol), the dispersion-corrected PBE-D3 and PBEsol-D3, were considered. Of these functionals, LDA was found to exhibit the highest degree of error, while PBEsol and PBE-D3 displayed the least error. Underestimated lattice parameters compared with experimental values were observed to result in higher force constants, leading to an overprediction of vibrational frequencies. Conversely, an overestimation of lattice parameters was associated with lower vibrational frequencies. The methodology presented in this study yielded results that are in good agreement with experiment, irrespective of the method (finite differences vs. density functional perturbation theory) employed for calculating infrared and Raman spectra. It was further demonstrated that for alkali halides with weak Raman scattering, utilizing a supercell constructed from primitive cells better predicts Raman features than does the use of conventional cells.

Raman↗
DOE OSTI2020

Tunable Magnetic Exchange between Rare-Earth Metal 5d and Iron 3d States: A Case Study of the Multiple Magnetic Transitions in Gd 6 FeBi 2 and the Solid Solutions Dy 6– x Gd x FeBi 2 (1 ≤ x ≤ 5) with Curie Temperatures in the Range 120–350 K

In this paper, the room-temperature magnet Gd 6 FeBi 2 was comprehensively characterized by means of temperature-dependent single-crystal X-ray diffraction, magnetization measurements, and experimental electron density and electronic structure computations. This work explores the electron-spin effects of Fe on this structure and suggests that Gd6FeBi2 shows structural features and exchange interactions, which are clearly distinguishable from other analogues, including the solid solutions Dy 6–x Gd x FeBi 2 (0 ≤ x ≤ 5). The unique traits of Gd 6 FeBi 2 and its derivatives encompass abnormal variations of lattice parameters with the temperature, as well as the presence of multiple magnetic transitions of complex nature. Based on the comprehensive analyses, it can be suggested that the unique magnetic response in this material is the result from tunable Fe spin states, which are coupled with strong Gd 5d–Fe 3d interactions, which differ from other members of this large, structural family. In the ground state, according to density functional theory calculations, the Fe atom carries two net electrons, whose spins are coupled in an antiparallel fashion to the spins of the Gd electrons. Near the Curie temperature, the Fe net moment is reduced intermittently, coupled with a multiple of magnetic transitions. The magnetic correlations are manifested in unexpected variations of the lattice parameters as a function of temperature, suggesting spin–lattice interactions. Furthermore, this study emphasizes the important role of Gd 5d electrons in tuning Fe 3d-based magnetic contribution, which enables better understanding on the spin coupling in other related compounds and sheds light on the development of new magnetic and spintronic compounds.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Analysis of the Defect Structure of B2 Feal Alloys

The Bozzolo, Ferrante and Smith (BFS) method for alloys is applied to the study of the defect structure of B2 FeAI alloys. First-principles Linear Muffin Tin Orbital calculations are used to determine the input parameters to the BFS method used in this work. The calculations successfully determine the phase field of the B2 structure, as well as the dependence with composition of the lattice parameter. Finally, the method is used to perform 'static' simulations where instead of determining the ground state configuration of the alloy with a certain concentration of vacancies, a large number of candidate ordered structures are studied and compared, in order to determine not only the lowest energy configurations but other possible metastable states as well. The results provide a description of the defect structure consistent with available experimental data. The simplicity of the BFS method also allows for a simple explanation of some of the essential features found in the concentration dependence of the heat of formation, lattice parameter and the defect structure.

Bozzolo, Guillermo↗