Search NASA⌕ Search

SEARCH · Search NASA

Results for “layered metal oxides”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

A layered nonstoichiometric lepidocrocite-type sodium titanate anode material for sodium-ion batteries

A lepidocrocite-structured sodium titanate prepared by ion-exchange of a Cs-containing precursor shows promise as an anode material for sodium ion batteries, with a discharge capacity of up to 229 mAh g -1 at an average potential of about 0.6 V vs. Na + /Na. Titanium vacancies in the metal oxide layers provide additional sites for sodium intercalation in addition to interlayer sites, which accounts for the higher capacity compared to other previously reported lepidocrocite-structured titanates. By screening a series of electrolyte formulations and binders, we were able to improve the first-cycle coulombic efficiency to 81.8% and 94.7% respectively using CMC/SBR-based and binder-free electrodes in ether electrolytes. Finally, the electrochemical consequences of short-term air-exposure on the electrodes are also discussed.

25 ENERGY STORAGE↗
DOE OSTI2019

Approaches to investigate the role of chelation in the corrosivity of biomass-derived oils

The need to provide the U.S. market with a renewable liquid fuel energy source from a non-food feedstock stream has gained considerable traction due to benefits such as improved energy efficiency, reduced environmental impacts, and enhanced national security. Practical achievement of these goals via biomass and bio-waste utilization involves production of liquid intermediates containing corrosive, reactive species like carboxylic acids, ketones, aldehydes, and hydroxyaldehydes. Such mixtures challenge materials of containment, processing, and transport. It is widely recognized that the smaller organic acids, such as acetic and formic, are corrosive and can remove protective surface oxides on alloys used in bio-oil processing infrastructure, and ketones can swell sealing polymers. However, literature shows, and findings herein confirm, larger carboxylic acids and bidentate alcohols are present. This highlights the potential for synergistic, detrimental effects of constituents in bio-oil corrosion, including direct reactivity of small acids compounded with the possibility of mobilization of protective metal oxide layers via chelation by larger acids and oxygenates. The question of whether species beyond small acids can significantly contribute to corrosion requires analytical approaches previously not applied to bio-oil corrosion studies and certainly not previously applied corroboratively. As such, this work introduces a combination of optical, mass spectral, and electrochemical impedance spectroscopies with an incubation approach to study metal mobilization, to facilitate elucidating chelation's role in bio-oil corrosive pathways. To enable systematic study of these oxygenates' material compatibility individually and in combination, a model matrix of bio-oil constituents was also developed based on identification of key components of real bio-oils.

09 BIOMASS FUELS↗
DOE OSTI2020

Phase stabilization and oxidation of a continuous composition spread multi-principal element (AlFeNiTiVZr) 1-x Cr x alloy

Multi-Principal Element Alloys (MPEA) have been hypothesized to maintain a stable single alloy phase and resist corrosion at high temperatures, which are desirable in various functional applications, including material of turbine blades. However, studies into oxidation resistant alloys have been constrained to individual MPEA systems or a limited selection of compositions within those systems. Here, High-Throughput Experimental (HTE) techniques were utilized to rapidly assess phase stability and resistance to oxidation of an (AlFeNiTiVZr) 1-x Cr x continuous composition spread (CCS) thin-film alloy system. High-throughput synchrotron diffraction and Raman spectroscopy were used to identify phases, especially high symmetry structures and oxides, as a function of annealing time and composition. The formation of two distinct phase regions, R 1 and R 2 , across the CCS was observed. One of these phase regions, R 2 , exhibited a stable high symmetry BCC-like phase at Cr concentrations greater than 25.4 at%, and grew a passivating mixed metal surface oxide; whereas, the R 1 phase region, decomposed on oxidation to multiple oxides and reacted with the substrate to form silicides. The passivating mixed metal oxide layer appears to prevent destabilization of the (AlFeNiTiVZr) 1-x Cr x MPEA BCC solid solution. Furthermore, at longer annealing times the passivating phase was seen only above 29.2 at% Cr. High Cr-doped (AlFeNiTiVZr) 1-x Cr x appear to be a good candidate for high temperature, oxidation-resistant structural alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effect of TiO x Substrate Interactions on the Electrocatalytic Oxygen Reduction Reaction at Au Nanoparticles

Here, we report a robust model for studying electrocatalytic reactions at metal nanoparticles (NPs) in contact with metal oxide surfaces. The metal oxide layer (TiO x ) is prepared by atomic layer deposition, and it is sufficiently thin that it does not hinder electron transfer from the underlying conductive electrode to the supported AuNP electrocatalysts. In advance of the experiments, density functional theory (DFT) predicted that direct contact between AuNPs and TiO x would lead to enhanced activity for the oxygen reduction reaction (ORR). DFT attributes the observed ORR enhancement to partial charge transfer from oxygen vacancies within the TiO x film to the supported AuNPs and hence formation of anionic Au species. The experimental findings are in near quantitative agreement with the DFT results. Specifically, compared to isolated AuNPs, decreases of ~ 100 and ~ 50 mV in the ORR onset potential are observed experimentally for AuNPs supported on TiO 1.9 and TiO 2.0 films, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Moderate active Fe 3+ doping enables improved cationic and anionic redox reactions for wide-voltage-range sodium storage

Layered metal oxides are promising cathode materials for sodium-ion batteries (SIBs) due to their high theoretical specific capacity and wide Na + diffusion channels. However, the irreversible phase transitions and cationic/anionic redoxes cause fast capacity decay. Herein, P2-type Na 0.67 Mg 0.1 Mn 0.8 Fe 0.1 O 2 (NMMF-1) cathode material with moderate active Fe 3+ doping has been designed for sodium storage. Uneven Mn 3+ /Mn 4+ distribution is observed in NMMF-1 and the introduction of Fe 3+ is beneficial for reducing the Mn 3+ contents both at the surface and in the bulk to alleviate the Jahn–Teller effect. The moderate Fe 3+ /Fe 4+ redox can realize the best tradeoff between capacity and cyclability. Therefore, the NMMF-1 demonstrates a high capacity (174.7 mAh g -1 at 20 mA g -1 ) and improved cyclability (78.5% over 100 cycles) in a wide-voltage range of 1.5–4.5 V (vs. Na + /Na). In-situ X-ray diffraction reveals a complete solid-solution reaction with a small volume change of 1.7% during charge/discharge processes and the charge compensation is disclosed in detail. This study will provide new insights into designing high-capacity and stable layered oxide cathode materials for SIBs.

25 ENERGY STORAGE↗
DOE OSTI2025

Electrochemical Random-Access Memory: Progress, Perspectives, and Opportunities

Non-von Neumann computing using neuromorphic systems based on analogue synaptic and neuronal elements has emerged as a potential solution to tackle the growing need for more efficient data processing, but progress toward practical systems has been stymied due to a lack of materials and devices with the appropriate attributes. Recently, solid state electrochemical ion-insertion, also known as electrochemical random access memory (ECRAM) has emerged as a promising approach to realize the needed device characteristics. ECRAM is a three terminal device that operates by tuning electronic conductance in functional materials through solid-state electrochemical redox reactions. This mechanism can be considered as a gate-controlled bulk modulation of dopants and/or phases in the channel. Early work demonstrating that ECRAM can achieve nearly ideal analogue synaptic characteristics has sparked tremendous interest in this approach. More recently, the realization that electrochemical ion insertion can be used to tune the electronic properties of many types of materials including transition metal oxides, layered two-dimensional materials, organic and coordination polymers, and that the changes in conductance can span orders of magnitude has further attracted interest in ECRAM as the basis for analogue synaptic elements for inference accelerators as well as for dynamical devices that can emulate a wide range of neuronal characteristics for implementation in analogue spiking neural networks. At its core, ECRAM shares many fundamental aspects with rechargeable batteries, where ion insertion materials are used extensively for their ability to reversibly store charge and energy. Computing applications, however, present drastically different requirements: systems will require many millions of devices, scaled down to tens of nanometers, all while achieving reliable electronic-state tuning at scaled-up rates and endurances, and with minimal energy dissipation and noise. Further, in this review, we discuss the history, basic concepts, recent progress, as well as the challenges and opportunities for different types of ECRAM, broadly grouped by their primary mobile ionic charge carrier, including Li, protons, and oxygen vacancies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Stabilization of Dinuclear Rhodium and Iridium Clusters on Layered Titanate and Niobate Supports

Atomically dispersed organometallic clusters can provide well-defined nuclearity of active sites for both fundamental studies as well as new regimes of activity and selectivity in chemical transformations. More recently, dinuclear clusters adsorbed onto solid surfaces have shown novel catalytic properties resulting from the synergistic effect of two metal centers to anchor different reactant species. Difficulty in synthesizing, stabilizing, and characterizing isolated atoms and clusters without agglomeration challenges allocating catalytic performance to atomic structure. Here, we explore the stability of dinuclear rhodium and iridium clusters adsorbed onto layered titanate and niobate supports using molecular precursors. Both systems maintain their nuclearity when Statistical analysis of HAADF-STEM images revealed that rhodium and iridium dimers had mean cluster-to-cluster distances very similar to what is expected from a random distribution of atoms over a large area, indicating that they are dispersed without aggregation. The stability of dinuclear rhodium clusters supported on titanate nanosheets was also investigated by X-ray absorption fine structure (EXAFS), DRIFTS, and first-principles calculations. Both X-ray absorption spectroscopy and HAADF-STEM simulations, guided by density functional theory (DFT)-optimized structure models, suggested that rhodium dimers adsorb onto the nanosheets in an end-on binding mode that is stable up to 100 degrees C under reducing conditions. Finally, this study highlights that crystalline nanosheets derived from layered metal oxides can be used as model supports to selectively stabilize dinuclear clusters, which could have implications for heterogeneous catalysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High-Pressure Polymorphism in Silver Ferrite Delafossite, AgFeO 2

The delafossites are a class of layered metal oxides that are notable for being able to exhibit optical trans- parency alongside an in-plane electrical conductivity, making them promising platforms for the development of transparent conductive oxides. Pressure-induced polymorphism offers a direct method for altering the electrical and optical properties in this class, and although the copper delafossites have been studied extensively under pressure, the silver delafossites remain only partially studied. We report two new high-pressure polymorphs of silver ferrite delafossite, AgFeO 2 , that are stabilized above ~6 GPa and ~14 GPa. In situ X-ray diffraction and vibrational spectroscopy measurements are used to examine the structural changes across the two phase transitions. The high-pressure structure between 6–14 GPa is assigned as a monoclinic C2/c structure that is analogous to the high-pressure phase reported for AgGaO 2 . As a result, nuclear resonant forward scattering reveals no change in the spin state or valence state at the Fe 3+ site up to 15.3 GPa.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Electrooxidation of CO on Platinum Nanoparticles Supported on NiO Thin Films

In this paper, we report on a robust experimental model to investigate strong metal–support interactions (SMSI) and their effect on electrocatalytic reactions in the absence and presence of direct contact between the nanoparticles (NPs) and the metal oxide thin film. Specifically, we describe beneficial interactions between Ni 0.9 O thin film supports and PtNPs toward the CO electrooxidation reaction. The metal oxide layer (Ni 0.9 O) is prepared by atomic layer deposition and characterized using X-ray photoelectron spectroscopy (XPS). PtNPs, containing an average of either 55 (Pt 55 ) or 140 (Pt 140 ) atoms, were synthesized using a dendrimer encapsulation method. The results indicate negative shifts of ~100 and ~60 mV of the CO electrooxidation peak potential when Ni 0.9 O thin films are in contact with Pt 55 NPs and Pt 140 NPs, respectively. Additionally, the oxygen evolution reaction (OER) is suppressed only when the PtNPs are in contact with the Ni 0.9 O thin film. Density functional theory (DFT) calculations indicate that both the CO electrooxidation enhancement and suppression of the OER can be attributed to a 1.23 eV decrease of the CO* binding energy and a 0.35 eV increase of the OH* binding energy at a NiO(111)/Pt 55 NP interface compared to isolated Pt 55 NPs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Organic thin-film transistors with a bottom bilayer gate dielectric having a low operating voltage and high operational stability

This study reports on p-channel bottom-gate organic thin-film transistors (OTFT) that achieve low-voltage operation with a thin bilayer gate dielectric of CYTOP/HfO 2 that also leads to high operational stability. A bottom-gate geometry allows the thickness of the gate dielectric to be reduced to 17 nm, thereby increasing the gate dielectric capacitance density to a value of up to 258 nF/cm 2 . All OTFTs yielded threshold voltages (V TH ) lower than -1 V, thereby providing minimum operating voltage (gate to source voltage ~ V TH ) of -1 V with field-effect mobility values in the range from 0.3 to 0.8 cm 2 /Vs and subthreshold swing values below 100 mV/dec. Operational stability during DC bias stress was found similar to that measured in devices with a top-gate geometry, with about 1% of drain current change after 6 h. Here, using a double-stretched exponential function, the operational stability characteristics were modeled. It was found that by increasing the metal oxide layer thickness, the threshold voltage can shift toward positive values under DC stress tests. For CYTOP layer thicknesses above 15 nm, a thicker CYTOP layer was found to shift the threshold voltage in the opposite direction toward negative values. Furthermore, these p-channel bottom-gate organic transistor with a bilayer gate dielectric of CYTOP/HfO 2 combine high mobility, high operational stability, and lower voltage operation of -1 V compared to top-gate OTFTs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Multielectrode electrochemical cell for in situ structural characterization of amorphous thin-film catalysts using high-energy X-ray scattering

A multielectrode-based electrochemical cell allows the structural characterization of an amorphous thin-film water oxidation catalyst under various electrochemical potentials using high-energy X-ray scattering and atomic pair distribution function (PDF) techniques. A multielectrode with five electrodes provides a sufficiently low background signal to enable high-energy X-ray scattering (HEXS) measurements and amplifies the extremely low HEXS signals from samples for high-resolution PDF analysis of in situ data from thin-film catalysts. Glassy carbon (GC) creates a relatively low intensity HEXS pattern and is used as a working electrode. Instead of a three-dimensional (3D) porous electrode architecture, the flat geometry of the electrode enables various deposition techniques to be used for the preparation of a highly conductive metal oxide layer. PDF analysis demonstrates high spatial resolution for a 230 nm thick amorphous iridium oxide film deposited on two roughened 60 µm thick GC electrodes. The PDF analysis resolves the domain size and distinguishes changes in fine structure which are directly correlated with the structure and function of the catalysts. In conclusion, the results bring the opportunity to analyze the structure of nanometre-scale amorphous thin-film catalysts in an electrolyte-compatible and compact 3D-printed electrochemical cell in a three-electrode configuration.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A Reflection on the Evolution of Sodium/Metal Chloride (ZEBRA) Batteries and Lithium-Ion Cathode Materials (1975–2025): A Tribute to Johan Coetzer

This narrative summarizes, in retrospect, the enormous and quietly-conducted contribution of Dr Johan Coetzer, a South African scientist and entrepreneur, to the discovery, development and implementation of the high temperature sodium—metal chloride “ZEBRA” battery (Na/β-Al 2 O 3 , NaAlCl 4 /MCl 2 (M = Ni, Fe)). Here, this research activity was initiated in the mid 1970’s at the Council for Scientific and Industrial Research (CSIR) in South Africa and subsequently developed primarily in partnership with the Atomic Energy Research Establishment (AERE, Harwell, UK), Beta R&D (Derby, UK) and Daimler Benz (Germany), before being transferred to industry worldwide for electric vehicle and energy storage applications, albeit at a relatively low production rate. Coetzer’s wide-ranging, innovative and, at times, unconventional scientific approach also laid the foundation for the discovery and implementation of manganese-based spinel and layered metal oxide cathode materials for the Li-ion battery industry.

ZEBRA Battery↗
NASA NTRS1986

Corrosion of metals and alloys in sulfate melts at 750 C

The corrosion of Ni, Co, Ni-10Cr, Co-21Cr, and IN738 was studied at 750 C in the presence of molten sulfate mixtures (Na2SO4-Li2SO4 and Na2SO4-CoSO4) and in an atmosphere consisting of O2 + 0.12 percent SO2-SO3. The corrosion was observed to be similar for both Na2SO4-Li2SO4 and Na2SO4-CoSO4 melts. The corrosion of Ni and Co took place by the formation of a mixed oxide plus sulfide scale, very similar to the corrosion in SO2 or SO3 alone. The initial stage for the corrosion of Ni-10Cr involved the formation of a thick NiO + Ni3S2 duplex scale, and Cr sulfide was formed during the later stages. A pitting type of morphology was observed for both Co-21Cr and IN738. The pit was Cr sulfide at the beginning, and subsequently the sulfides oxidized to Cr2O3. A base-metal oxide layer was present above the pit, and this was observed to be formed very early in the corrosion process. A mechanism is proposed to explain this. In general, the formation of sulfides appears to be the primary mode of degradation in mixed sulfide melts.

Misra, A. K.↗
NASA NTRS1994

Low Earth orbit durability evaluation of protected silicone for advanced refractive photovoltaic concentrator arrays

The need for efficient, cost effective sources of electrical power in space has led to the development of photovoltaic power systems which make use of novel refractive solar concentrators. These concentrators have been conceived in both point-focus and linear-focus designs. Current concentrator lenses are fabricated from flexible silicones with Fresnel facets along their inside surface. To insure the efficient operation of these power systems, the concentrator lenses must be durable and the silicone material must remain specularly transmitting over a reasonable lifetime in low Earth orbit (LEO) and other space environments. Because of the vulnerability of silicones to atomic oxygen and ultraviolet radiation in LEO these lenses have been coated with a multi-layer metal oxide protective coating. The objective of this research was to evaluate the LEO durability of the multilayer coated silicone for advanced refractive photovoltaic concentrator arrays with respect to optical properties and microstructure. Flat metal oxide coated silicone samples were exposed to ground-laboratory and in-space atomic oxyqen for durability evaluation.

Degroh, Kim K.↗
NASA NTRS2010

A Study on Advanced Lithium-Based Battery Cell Chemistries to Enhance Lunar Exploration Missions

NASAs Exploration Technology Development Program (ETDP) Energy Storage Project conducted an advanced lithium-based battery chemistry feasibility study to determine the best advanced chemistry to develop for the Altair Lunar Lander and the Extravehicular Activities (EVA) advanced Lunar surface spacesuit. These customers require safe, reliable batteries with extremely high specific energy as compared to state-of-the-art. The specific energy goals for the development project are 220 watt-hours per kilogram (Wh/kg) delivered at the battery-level at 0 degrees Celsius ( C) at a C/10 discharge rate. Continuous discharge rates between C/5 and C/2, operation between 0 and 30 C and 200 cycles are targeted. Electrode materials that were considered include layered metal oxides, spinel oxides, and olivine-type cathode materials, and lithium metal, lithium alloy, and silicon-based composite anode materials. Advanced cell chemistry options were evaluated with respect to multiple quantitative and qualitative attributes while considering their projected performance at the end of the available development timeframe. Following a rigorous ranking process, a chemistry that combines a lithiated nickel manganese cobalt oxide Li(LiNMC)O2 cathode with a silicon-based composite anode was selected as the technology that can potentially offer the best combination of safety, specific energy, energy density, and likelihood of success.

Reid, Concha M.↗
NASA NTRS2009

A Study on Advanced Lithium-Based Battery Cell Chemistries to Enhance Lunar Exploration Missions

NASA's Exploration Technology Development Program (ETDP) Energy Storage Project conducted an advanced lithium-based battery chemistry feasibility study to determine the best advanced chemistry to develop for the Altair lunar lander and the Extravehicular Activities (EVA) advanced lunar surface spacesuit. These customers require safe, reliable energy storage systems with extremely high specific energy as compared to today's state-of-the-art batteries. Based on customer requirements, the specific energy goals for the development project are 220 watt-hours per kilogram (Wh/kg) delivered at the battery level at 0 degrees Celsius (degrees Celcius) at a C/10 discharge rate. Continuous discharge rates between C/5 and C/2, operation over 0 to 30 degrees C, and 200 cycles are targeted. The team, consisting of members from NASA Glenn Research Center, Johnson Space Center, and Jet Propulsion laboratory, surveyed the literature, compiled information on recent materials developments, and consulted with other battery experts in the community to identify advanced battery materials that might be capable of achieving the desired results with further development. A variety of electrode materials were considered, including layered metal oxides, spinel oxides, and olivine-type cathode materials, and lithium metal, lithium alloy, and silicon-based composite anode materials. lithium-sulfur systems were also considered. Hypothetical cell constructs that combined compatible anode and cathode materials with suitable electrolytes, separators, current collectors, headers, and cell enclosures were modeled. While some of these advanced materials are projected to obtain the desired electrical performance, there are risks that also factored into the decision making process. The risks include uncertainties due to issues such as safety of a system containing some of these materials, ease of scaling-up of large batches of raw materials, adaptability of the materials to processing using established or reasonable cost manufacturing techniques, manufacturability of the materials in dimensions required for integration into battery cells of practical capacities, low Technology Readiness levels (TRl), and the ability to achieve the desired performance by the customer need dates. The advanced cell chemistry options were evaluated with respect to multiple quantitative and qualitative attributes while considering their projected performance at the end of the available development timeframe. Following a rigorous ranking process, a chemistry that combines a lithiated nickel manganese cobalt oxide (lithium NMC) cathode with a silicon-based composite anode was selected as the technology that can offer the best combination of safety, specific energy, energy density, and likelihood of success. Tasks over the next three years will focus on development of electrode materials, compatible electrolytes, and separator materials, and integration of promising components to assess their combined performance in working cells. Cells of the chosen chemistry will be developed to TRl 6 by 2014 and will then be transferred to the customers for infusion into their mission paths.

Reid, Concha↗
NASA NTRS2013

Alternative to Nitric Acid Passivation Project Overview

The standard practice for protection of stainless steel is a process called passivation. This procedure results in the formation of a metal oxide layer to prevent corrosion. Typical passivation procedures call for the use of nitric acid which exhibits excellent corrosion performance; however, there are a number of environmental, worker safety, and operational issues associated with its use. The longtime military specification for the passivation of stainless steel was cancelled in favor of newer specifications which allow for the use of citric acid in place of nitric acid. Citric acid offers a variety of benefits that include increased safety for personnel, reduced environmental impact, and reduced operational costs. There have been few studies, however, to determine whether citric acid is an acceptable alternative for NASA and DoD. This paper details activities to date including development of the joint test plan, on-going and planned testing, and preliminary results.

Lewis, Pattie L.↗
NASA NTRS2012

Wide Operating Temperature Range Electrolytes for High Voltage and High Specific Energy Li-Ion Cells

A number of electrolyte formulations that have been designed to operate over a wide temperature range have been investigated in conjunction with layered-layered metal oxide cathode materials developed at Argonne. In this study, we have evaluated a number of electrolytes in Li-ion cells consisting of Conoco Phillips A12 graphite anodes and Toda HE5050 Li(1.2)Ni(0.15)Co(0.10)Mn(0.55)O2 cathodes. The electrolytes studied consisted of LiPF6 in carbonate-based electrolytes that contain ester co-solvents with various solid electrolyte interphase (SEI) promoting additives, many of which have been demonstrated to perform well in 4V systems. More specifically, we have investigated the performance of a number of methyl butyrate (MB) containing electrolytes (i.e., LiPF6 in ethylene carbonate (EC) + ethyl methyl carbonate (EMC) + MB (20:20:60 v/v %) that contain various additives, including vinylene carbonate, lithium oxalate, and lithium bis(oxalato)borate (LiBOB). When these systems were evaluated at various rates at low temperatures, the methyl butyrate-based electrolytes resulted in improved rate capability compared to cells with all carbonate-based formulations. It was also ascertained that the slow cathode kinetics govern the generally poor rate capability at low temperature in contrast to traditionally used LiNi(0.80)Co(0.15)Al(0.05)O2-based systems, rather than being influenced strongly by the electrolyte type.

Li-ion Battery↗