Search NASA⌕ Search

SEARCH · Search NASA

Results for “light absorption and conversion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Elucidation of the Active Sites in Single-Atom Pd 1 /CeO 2 Catalysts for Low-Temperature CO Oxidation

Supported precious metals with atomic dispersion are of great interest in catalysis due to their potentials in achieving maximum atom efficiency and unique reactivities. Herein, the active sites for low-temperature CO oxidation are elucidated over single-atom Pd 1 /CeO 2 catalysts prepared via high-temperature atom trapping (AT). The increased oxygen vacancies on CeO 2 surface induced by 800 °C air calcination result in decreased Pd–CeO 2 coordinations, i.e., the coordination-unsaturated Pd 2+ on CeO 2 . Light-off and light-out measurements coupled with CO-DRIFTS and X-ray absorption characterization confirm that these coordination-unsaturated Pd 2+ on CeO 2 are much more reactive than the fully coordinated counterpart, evidenced by a decrease of T 90 (temperature to achieve 90% conversion) by ~100 °C in CO oxidation at a gas hourly space velocity of 300 L g –1 h –1 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Sequential Deposition of Multicomponent Bulk Heterojunctions Increases Efficiency of Organic Solar Cells

Constructing tandem and multi-blend organic solar cells (OSCs) is an effective way to overcome the absorption limitations of conventional single-junction devices. However, these methods inevitably require tedious multilayer deposition or complicated morphology-optimization procedures. Herein, sequential deposition is utilized as an effective and simple method to fabricate multicomponent OSCs with a double-bulk heterojunction (BHJ) structure of the active layer to further improve photovoltaic performance. Two efficient donor-acceptor pairs, D18-Cl:BTP-eC9 and PM6:L8-BO, are sequentially deposited to form the D18-Cl:BTP-eC9/PM6:L8-BO double-BHJ active layer. In these double-BHJ OSCs, light absorption is significantly improved, and optimal morphology is also retained without requiring a more complicated morphology optimization involved in quaternary blends. Compared to the quaternary blend devices, energy loss (E loss ) is also reduced by rationally matching each donor with an appropriate acceptor. Consequently, the power conversion efficiency (PCE) is improved from 18.25% for D18-Cl:BTP-eC9 and 18.69% for PM6:L8-BO based binary blend OSCs to 19.61% for the double-BHJ OSCs. In contrast, a D18-Cl:PM6:L8-BO:BTP-eC9 quaternary blend of OSCs exhibited a dramatically reduced PCE of 15.83%. Finally, these results demonstrate that a double-BHJ strategy, with a relatively simple processing procedure, can potentially enhance the device performance of OSCs and lead to more widespread use.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of long-term light stability of negative charge injected into oxide-nitride-oxide passivation stack of crystalline silicon solar cells

A negatively charged oxide-nitride-oxide stack for field-effect passivation of crystalline silicon solar cells is discussed. The negative charge was injected into the stack by a plasma charge injection technology. Charge stability was studied by exposing samples to AM1.5 simulation visible light and full-spectrum light at temperatures ranging from 55 to 78 °C for up to 300 h. Charge injection and loss were quantified based on shifts in the flatband voltage of capacitance–voltage curves measured with a mercury probe. The most probable mechanism of charge loss was found to be diffusion of negative charged hydrogen atoms through nitride and bottom oxide. The optimum recipe for each layer of the stack was investigated to minimize the loss of injected charge. The flatband voltage decay of the optimized stack was found to fit a power-law trend, suggesting the dispersive transport of hydrogen atoms with a dispersion parameter of ~0.06–0.07. The optimized stack is projected to maintain a negative charge density of about 3.6 × 10 12 cm –2 or more after 25 years of field operation in an environment such as Arizona, which would be sufficient for field-effect passivation under one-sun illumination. Furthermore, the high stability of the negative injected charge makes the plasma charging technology a safer and lower cost alternative to Al 2 O 3 -passivation technology commonly used to passivate p-type surfaces.

14 SOLAR ENERGY↗
DOE OSTI2025

Shifting the MLCT of d 6 metal complexes to the red and NIR

Light-active d 6 -coordination compounds hold great promise for light energy conversion, sensors and therapeutic applications. However, the activity in the red-to-NIR spectral region is highly desirable to convert solar light more efficiently, use low-cost red-light sources and activate these chromophores in biological tissue environment. Due to their versatility, tunability and broad intense absorption, d 6 -coordination compounds with metalto-ligand charge transfer (MLCT) transitions are especially interesting. This review article offers a comprehensive collection of strategies to tune MLCT excited states in d 6 metal complexes and gives insights on group 6 to group 9 transition metals and their respective state-of-the-art MLCT engineering towards red-shifted absorption and emission properties with long-lived excited states. Strategies comprise lowering the π* level of the ligands, destabilizing and mixing of the metal-based HOMO, switching within a group of transition metals, matrix effects and insights into dealing with excited state deactivation in the context of the energy gap law.

Metal to ligand charge transfer (MLCT)↗
DOE OSTI2026

Interfacial Charge Transfer in Lead Sulfide/Cadmium Sulfide Quantum Dot–Monolayer Molybdenum Disulfide Heterostructures

We investigate the ultrafast interfacial charge transfer dynamics in mixed-dimensional PbS/CdS quantum dot (QD)–monolayer MoS 2 heterostructures exhibiting a type-II band alignment. These 0D–2D heterostructures were assembled using oleic acid-capped PbS/CdS QDs with systematically varied core sizes deposited onto molecular beam epitaxy-grown monolayer MoS 2 . Steady-state and time-resolved optical spectroscopies revealed pronounced bidirectional charge transfer between the 0D and 2D components, involving both electron and hole exchange across the interface. The quenching of the monolayer MoS 2 A-exciton bleach and the modifications of its decay dynamics provide direct evidence for efficient hole transfer from photoexcited MoS 2 into the PbS QD core. Concurrently, attenuation of the QD ground-state bleach and the emergence of ultrafast decay components confirmed electron transfer from photoexcited QDs to monolayer MoS 2 . Both hole and electron transfer processes are dependent on the QD core size, with smaller cores enabling faster transfer rates and higher efficiencies due to enhanced band offsets and interfacial coupling. The complementary insights gained from transient absorption and time-resolved photoluminescence measurements clarify the mechanisms governing interfacial carrier exchange and highlight the importance of both hole and electron transfer as key components in the functioning of such 0D–2D heterostructures. This study underscores the potential of 0D–2D semiconductor heterostructures for advanced optoelectronic and light-energy conversion applications.

36 MATERIALS SCIENCE↗
DOE OSTI2019

The Preparation and Characterization of Co–Ni Nanoparticles and the Testing of a Heterogenized Co–Ni/Alumina Catalyst for CO Hydrogenation

Samples of well-controlled nanoparticles consisting of alloys of cobalt and nickel of different atomic ratios were synthesized using wet chemical methods with oleylamine as the solvent and the reducing agent. These materials were characterized by a variety of techniques, including high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM), X-ray energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). Small amounts of heterogenized catalysts were prepared using alumina as the support. However, the potential for use of Co–Ni catalysts in CO hydrogenation was explored using a larger amount of Co–Ni/alumina catalyst prepared from standard aqueous impregnation methods and tested in a continuously stirred tank reactor (CSTR) for Fischer–Tropsch synthesis (FTS). Results are compared to a reference catalyst containing only cobalt. The heterogenized catalysts were characterized using synchrotron methods, including temperature programmed reduction with extended X-ray absorption fine structure spectroscopy and X-ray absorption near edge spectroscopy (TPR-EXAFS/XANES). The characterization results support intimate contact between Co and Ni, strongly suggesting alloy formation. In FTS testing, drawbacks of Ni addition included decreased CO conversion on a per gram catalyst basis, although Ni did not significantly impact the turnover number of cobalt, and produced slightly higher light gas selectivity. Benefits of Ni addition included an inverted induction period relative to undoped Co/Al2O3, where CO conversion increased with time on-stream in the initial period, and the stabilization of cobalt nanoparticles at a lower weight % of Co.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Solar-driven evaporators for water treatment: challenges and opportunities

Solar-driven evaporation is an emerging process to acquire freshwater from saline water or wastewater, in which photothermal materials play a crucial role. Additionally, significant effort has been devoted to promoting energy conversion efficiency by material and device design. In the current review, we discuss the major factors affecting evaporator efficiency and long-term performance, including selection of photothermal materials, promotion of evaporation efficiency, and solutions to the problem of scaling. Both the material components and structure will affect the absorption and reflection of the incident light, and the evaporation efficiency can be enhanced by reducing heat loss, enlarging surface area, and recycling latent heat. Scaling can be addressed by tailoring surface properties and structure.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2021

Infrared transmissive concentrated photovoltaics for coupling solar electric energy conversion to solar thermal energy utilization

The use of photovoltaic (PV) cells to convert solar energy to electricity is becoming increasingly prevalent; however, there are still significant limitations associated with the widespread adoption of PV cells for electricity needs. There is a clear need for a high efficiency solar power system that supplies electricity at a competitive cost and that provides for an on-demand supply of electricity as well as energy storage. By combining aspects of concentrated solar power and concentrated photovoltaics, the present invention provides a device that enables the conversion of sunlight to electricity at very high efficiencies and that enables the transmission of thermal energy to heat storage devices for later use. The disclosed device enables transmissive CPV through the use of a multijunction PV cell mounted on a transparent base. The use of a multijunction cell allows for highly efficient absorption of light above the bandgap of the lowest bandgap subcell. The transparent base permits transmission of a high percentage of the remaining light below the bandgap of the lowest bandgap subcell. The present invention also discloses a method of generating electricity through the use of a transmissive CPV device. Sunlight is concentrated onto one or more surfaces of the device. High energy light is absorbed by a multijunction PV cell and converted directly to electricity, while low energy light is transmitted through the device into a thermal storage device, which may then be coupled to a heat engine to generate dispatchable electricity.

Escarra, Matthew David↗
DOE OSTI2022

Benzotriazole‐Based Nonfused Ring Acceptors for Efficient and Thermally Stable Organic Solar Cells

Abstract Nonfused ring acceptors (NFRAs) have attracted significant attention for nonfullerene organic solar cells (OSCs) owing to their chemical tunability and facile synthesis. In this study, a benzotriazole‐based NFRA with chlorinated end groups (Triazole‐4Cl) is developed to realize highly efficient and thermally stable NFRA‐based OSCs; an analogous NFRA with nonchlorinated end groups (Triazole‐H) is synthesized for comparison. Triazole‐4Cl film exhibits the high‐order packing structure and the near‐infrared absorption capability, which are advantageous in charge transport and light harvesting of the resulting OSCs. In particular, the strong crystalline behavior of Triazole‐4Cl results in enhanced self‐aggregation, leading to high charge carrier mobility. Owing to these properties, a PBDB‐T (polymer donor):Triazole‐4Cl OSC demonstrates a high short‐circuit current, fill factor, and power conversion efficiency (PCE = 10.46%), outperforming a PBDB‐T:Triazole‐H OSC (PCE = 7.65%). In addition, the thermal stability of a PBDB‐T:Triazole‐4Cl OSC at an elevated temperature of 120 °C exceeds that of a PBDB‐T:Triazole‐H OSC. This is mainly attributed to the significantly higher cold crystallization temperature of Triazole‐4Cl (205.9 °C). This work provides useful guidelines for the design of NFRAs to achieve efficient and thermally stable NFRA‐based OSCs.

Polymer Science↗
DOE OSTI2023

Surface‐modified Ag@Ru‐P25 for photocatalytic CO 2 conversion with high selectivity over CH 4 formation at the solid–gas interface

Systematic optimization of the photocatalyst and investigation of the role of each component is important to maximizing catalytic activity and comprehending the photocatalytic conversion of CO 2 reduction to solar fuels. A surface-modified Ag@Ru-P25 photocatalyst with H 2 O 2 treatment was designed in this study to convert CO 2 and H 2 O vapor into highly selective CH 4 . Ru doping followed by Ag nanoparticles (NPs) cocatalyst deposition on P25 (TiO 2 ) enhances visible light absorption and charge separation, whereas H 2 O 2 treatment modifies the surface of the photocatalyst with hydroxyl (–OH) groups and promotes CO 2 adsorption. High-resonance transmission electron microscopy, X-ray photoelectron spectroscopy, X-ray absorption near-edge structure, and extended X-ray absorption fine structure techniques were used to analyze the surface and chemical composition of the photocatalyst, while thermogravimetric analysis, CO 2 adsorption isotherm, and temperature programmed desorption study were performed to examine the significance of H 2 O 2 treatment in increasing CO 2 reduction activity. The optimized Ag 1.0 @Ru 1.0 -P25 photocatalyst performed excellent CO 2 reduction activity into CO, CH 4 , and C 2 H 6 with a ~95% selectivity of CH 4 , where the activity was ~135 times higher than that of pristine TiO 2 (P25). For the first time, this work explored the effect of H 2 O 2 treatment on the photocatalyst that dramatically increases CO 2 reduction activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

A review of Sb 2 Se 3 photovoltaic absorber materials and thin-film solar cells

Energy generated from environmentally friendly, cost-effective solar cells is a key aspect for developing a clean renewable-energy economy. Non-toxic and Earth-abundant materials with high absorption coefficient (>10 5 cm -1 ) and optimal bandgap (1-1.5 eV) have received great attention as photovoltaic (PV) absorber layers during the last few decades. Among them, antimony selenide (Sb 2 Se 3 ) has been a promising PV absorber, with steadily increasing power-conversion efficiency (PCE) compared to other emerging compounds. Very recent studies showed that high-quality ZnO:Al/ZnO/CdS/TiO 2 /Sb 2 Se 3 /MoSe 2 /Mo devices with PCE of 9.2% can be fabricated using cost-effective novel compounds. Considering these recent advances, this article provides an overview of the material properties of Sb2Se3 thin films and the recent progress made with Sb 2 Se 3 -based solar cells. Furthermore, analysis of Sb 2 Se 3 -based thin-film solar cells has also shown that the devices have relatively good light management due to their suitable bandgap and high absorption coefficient, whereas carrier management, i.e. collection efficiency of photo-generated carriers, needs significant improvement. Overall, this study provides background knowledge on material properties and device performance and suggests main research directions to overcome the limiting factors of solar cell performance.

14 SOLAR ENERGY↗
DOE OSTI2021

Control of zeolite microenvironment for propene synthesis from methanol

Optimising the balance between propene selectivity, propene/ethene ratio and catalytic stability and unravelling the explicit mechanism on formation of the first carbon–carbon bond are challenging goals of great importance in state-of-the-art methanol-to-olefin (MTO) research. We report a strategy to finely control the nature of active sites within the pores of commercial MFI-zeolites by incorporating tantalum(V) and aluminium(III) centres into the framework. The resultant TaAlS-1 zeolite exhibits simultaneously remarkable propene selectivity (51%), propene/ethene ratio (8.3) and catalytic stability (>50 h) at full methanol conversion. In situ synchrotron X-ray powder diffraction, X-ray absorption spectroscopy and inelastic neutron scattering coupled with DFT calculations reveal that the first carbon–carbon bond is formed between an activated methanol molecule and a trimethyloxonium intermediate. The unprecedented cooperativity between tantalum(V) and Brønsted acid sites creates an optimal microenvironment for efficient conversion of methanol and thus greatly promotes the application of zeolites in the sustainable manufacturing of light olefins.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Imaging Nanoscale Energy Transport and Conversion with Ultrafast Electron Microscopy (Final Technical Report)

Light-matter interactions are ubiquitous in nature and reside at the heart of innumerable technologies. The cascade of processes that occur when a material absorbs a photon of light are exceedingly complex and are interwoven in both space and time, rendering precise determination of the atomic-scale and ultrafast mechanisms immensely challenging. The advent of methods for generating short pulses of light several decades ago led to major advances in understanding the initial moments of light absorption and the resultant effects, though directly interrogating the response of the atoms within the material continued to prove challenging. More recently, methods for generating ultrashort pulses of X-rays and fast electrons have opened the way to probing photoinduced structural dynamics of a wide range of matter in multiple phases. An especially promising laboratory-scale method is ultrafast electron microscopy (UEM), wherein the modalities of conventional transmission electron microscopes (imaging, diffraction, spectroscopy) are extended into the femtosecond temporal regime. Here, the ultrafast imaging and diffraction modalities of UEM were used to study the transient structural aspects of photoexcitation of semiconducting materials (e.g., spatially-resolved electron-phonon coupling, excitation and emission of acoustic phonons, and discrete nanoscale scattering processes). The project had three main objectives: (1) determination of the excitation mechanisms of dense, hypersonic charge-carrier waves and the spatially mediated means by which they couple to the lattice via coherent phonon emission, especially with UEM imaging, wherein effects of nanoscale structural and morphological features on the coupling and relaxation dynamics are expected to dictate nucleation sites and preferred wave vectors, (2) elucidation of photoinduced acoustic-phonon seeding, emergence, propagation, and decay over nanoscale crystal regions and especially with respect to local strain fields and atomic-scale disruptions in lattice order, and (3) interwoven with the first two were efforts aimed at realizing combined angstrom-femtosecond spatiotemporal imaging with UEM. The outcomes and impacts of this project were the generation of new knowledge with respect to fundamental light-matter interactions and, especially, the spatially-mediated excitation and evolution of the structural response of materials following coherent photoexcitation. Importantly, the spatial and temporal resolutions of the UEM imaging modalities used are well-suited for such studies and enable spatially-resolved mechanisms to be determined as a function of atomic order, structural features, and morphology. In addition, ultrafast crystallographic measurements were used to correlate real- and reciprocal-space dynamics in order to determine atomic-scale preferential wave vectors and ultrafast scattering mechanisms, especially as dictated by specimen boundary conditions. The obtained results, as detailed in peer-reviewed publications and presentations, illustrate the importance of ultrafast, angstrom-scale real-space imaging for developing a comprehensive understanding of energy transport and conversion in materials.

47 OTHER INSTRUMENTATION↗
DOE OSTI2021

Regulating crystallization to maintain balanced carrier mobility via ternary strategy in blade-coated flexible organic solar cells

Regulating the crystallization of donor and acceptor to maintain balanced carrier mobility is of great importance to fabricate efficient organic solar cells (OSCs). Herein, the balanced crystallinity between donor and acceptor was finely controlled in blade-coated OSCs. By adding high crystalline FOIC into PBDB-T:ITIC system, a balanced carrier mobility was achieved, resulting in the much improved fill factor. The optimized ternary device exhibits an increased current density, due to the enhanced light-harvesting efficiency with complementary absorption and the morphology change. Morphology characterization demonstrated that the ternary film exhibits a highly balanced crystallinity between the donor and acceptor on account of the formation of acceptor alloy. Moreover, the ternary film not only possesses a small domain size, but also exhibits a high domain purity as compared to both binary films. Encouragingly, a highest power conversion efficiency (PCE) of 10.68% was obtained for the blade-coated ternary OSCs. In addition, the blade-coated flexible large-area (105 mm 2 ) OSC based on PBDB-T:ITIC:FOIC ternary system also exhibits a high PCE of 9.81%, showing great potential in the high-throughput fabrication of OSCs.

14 SOLAR ENERGY↗
DOE OSTI2021

Electron shuttle in the MOF derived TiO 2 /CuO heterojunction boosts light driven hydrogen evolution

Metal organic frameworks (MOFs) have emerged as a novel template to develop porous photocatalytic materials for solar fuel conversion. In this work, we report the synthesis, charge separation dynamics, and photocatalytic performance of the TiO 2 /CuO heterostructure derived from mixed-phase MOFs based on Ti and Cu metal nodes, which demonstrates significantly enhanced catalytic activity for the hydrogen evolution reaction (HER) compared to metal oxides derived from single node MOFs. More importantly, using transient absorption spectroscopy, we identified the specific role each component in the heterostructure plays and unravelled the key intermediate species that is responsible for the exceptional photocatalytic activity of the heterostructure. We found that the HER is initiated with ultrafast electron transfer (<150 fs) from the molecular photosensitizer to the conduction band of TiO 2 , where TiO 2 acts as an electron mediator and shuttles the electron to the CuO cocatalyst, facilitating charge separation and ultimately boosting the HER efficiency. Overall, these results not only demonstrate the great potential of using mixed-phase MOFs as templates to synthesize mesoporous heterostructure photocatalysts but also provide important insight into the HER mechanism.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

A review of in situ/operando studies of heterogeneous catalytic hydrogenation of CO 2 to methanol

Repurposing CO 2 into chemicals, one of the Carbon Dioxide Removal (CDR) strategies, still faces significant challenges in conversion and energy efficiency due to the lack of effective catalysts and processes. Fundamental understanding through in situ/operando investigations of the reaction mechanisms and catalyst structures is pivotal for developing the efficient catalysts. This paper reviews the past and recent in situ/operando studies of methanol synthesis from heterogeneous CO 2 hydrogenation over a few typical catalysts including Cu-based, oxide-based, and noble-metal-based catalysts. With the development of high-pressure reactors, in situ/operando IR, X-ray absorption spectroscopy (XAS), X-ray diffraction (XRD), neutron diffraction and imaging have been used to reveal the surface intermediates and structures of working catalysts under CO 2 hydrogenation conditions. On the one hand, the combined operando techniques shed light on working mechanisms for some catalytic systems. On the other hand, due to the complexity of selective CO 2 hydrogenation reaction and limited sensitivity of current accessible operando techniques to the surface structure of catalysts, it is still murky about the exact nature of the active sites at the surface/interface and how different sites promote different reaction paths. Furthermore, it is concluded that new methodologies for differentiating signals from different sites, and the development of surface-sensitive techniques for high pressure reactions are needed for providing structural descriptors of highly active and selective CO 2 conversion catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Multicolor Inks of Black Phosphorus for Midwave‐Infrared Optoelectronics

Abstract Black phosphorus (bP) based ink with a bulk bandgap of 0.33 eV ( λ = 3.7 µm) has recently been shown to be promising for large‐area, high performance mid‐wave infrared (MWIR) optoelectronics. However, the development of multicolor bP inks expanding across the MWIR wavelength range has been challenging. Here a multicolor ink process based on bP with spectral emission tuned from 0.28 eV ( λ = 4.4 µm) to 0.8 eV ( λ = 1.5 µm) is demonstrated. Specifically, through the reduction of bP particle size distribution (i.e., lateral dimension and thickness), the optical bandgap systematically blueshifts, reaching up to 0.8 eV. Conversely, alloying bP with arsenic (bP 1− x As x ) induces a redshift in the bandgap to 0.28 eV. The ink processed films are passivated with an infrared‐transparent epoxy for stable infrared emission in ambient air. Utilizing these multicolor bP‐based inks as an infrared light source, a gas sensing system is demonstrated that selectively detects gases, such as CO 2 and CH 4 whose absorption band varies around 4.3 and 3.3 µm, respectively. The presented ink formulation sets the stage for the advancement of multiplex MWIR optoelectronics, including spectrometers and spectral imaging using a low‐cost material processing platform.

Kim, Jae Ik↗
DOE OSTI2020

Distinguishing resonance symmetries with energy-resolved photoion angular distributions from ion-pair formation in O 2 following two-photon absorption of a 9.3 eV femtosecond pulse

We present a combined experimental and theoretical study on the photodissociation dynamics of ion-pair formation in O 2 following resonant two-photon absorption of a 9.3 eV femtosecond pulse, where the resulting O + ions are detected using 3-D momentum imaging. Ion-pair formation states of $^3\Sigma^-_g$ and $^3\Pi_g$ symmetry are accessed through predissociation of optically dark continuum Rydberg states converging to the B $^2\Sigma^-_g$ ionic state, which are resonantly populated via a mixture of both parallel-parallel and parallel-perpendicular two-photon transitions. This mixture is evident in the angular distribution of the dissociation relative to the light polarization, and varies with the kinetic energy release (KER) of the fragmenting ion-pair. The KER-dependent photoion angular distribution reveals the underlying two-photon absorption dynamics involved in the ion-pair production mechanism and indicates the existence of two nearly degenerate continuum resonances possessing different symmetries, which can both decay by coupling to ion-pair states of the same total symmetry through internal conversion.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗