Search NASA⌕ Search

SEARCH · Search NASA

Results for “liquid/ gas diffusion layer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Accelerated Oxygen Mass Transfer in Copper and Vanadium Oxide-Based MIEC-Redox Membrane

Mixed ionic-electronic conducting (MIEC) membranes have a great potential for use in gas separation technology in the production of pure oxygen for metallurgy, micro- and nanoelectronics, biotechnology, pharmaceutics, etc. Before this happens, an important issue has to be addressed. This issue involves the design of novel MIEC membranes with enhanced oxygen transport. Recently, a concept of thick two-layer solid/liquid composite MIEC-Redox membranes with accelerated diffusion-bubbling oxygen transfer was proposed (see Belousov and Fedorov in ACS Appl Mater Interfaces 10:21794–21798, 2018). These diffusion-bubbling membranes could serve for efficient oxygen separation from air. However, there is no enough fundamental understanding of the mass transport processes involved. This understanding is important for evaluating the potential of MIEC-Redox membranes for practical application. The presented article gives a theory of oxygen mass transfer in two-layer copper and vanadium oxide-based MIEC-Redox membranes. The theory describes both the transport of oxygen ions in the outer layer of the membrane and the nucleation, growth, and transport of oxygen gas bubbles in the inner layer of the membrane. Kinetic regularities of oxygen mass transfer are established. The ways to enhance the productivity of MIEC-Redox membranes are outlined.

36 MATERIALS SCIENCE↗

Using operando techniques to understand and design high performance and stable alkaline membrane fuel cells

There is a need to understand the water dynamics of alkaline membrane fuel cells under various operating conditions to create electrodes that enable high performance and stable, long-term operation. Here we show, via operando neutron imaging and operando micro X-ray computed tomography, visualizations of the spatial and temporal distribution of liquid water in operating cells. We provide direct evidence for liquid water accumulation at the anode, which causes severe ionomer swelling and performance loss, as well as cell dryout from undesirably low water content in the cathode. We observe that the operating conditions leading to the highest power density during polarization are not generally the conditions that allow for long-term stable operation. This observation leads to new catalyst layer designs and gas diffusion layers. This study reports alkaline membrane fuel cells that can be operated continuously for over 1000 h at 600 mA cm -2 with voltage decay rate of only 32-μV h -1 – the best-reported durability to date.

25 ENERGY STORAGE↗

Theory of Influence of a Low-Volatility, Soluble Impurity on Spherically-Symmetric Combustion of Fuel Droplets

Analyses are given for the evolution of liquid-phase mass fraction profiles and temperature during combustion of fuel droplets composed of binary miscible mixtures of low-volatility and high-volatility constituents, with small initial mass fractions of the low-volatility material, or slow introduction of low-volatility material into the liquid phase by absorption from the gas phase. The gas phase is assumed to remain quasi-steady and the liquid temperature spatially uniform. The ratio of the liquid-phase diffusion coefficient to the initial burning-rate constant is treated as a small parameter. Asymptotic analyses in this parameter are developed, and the conservation equations are integrated numerically in obtaining descriptions of the combustion history. It is shown that at the surface of the droplet a boundary layer arises in which the mass fraction of the low-volatility component increases with time. The results are used to explain qualitatively some observed conditions of flame contraction and liquid disruption in droplet combustion.

Shaw, B. D.↗

Engineering Catalyst–Electrolyte Microenvironments to Optimize the Activity and Selectivity for the Electrochemical Reduction of CO 2 on Cu and Ag

We report the electrochemical reduction of carbon dioxide (CO 2 R) driven by renewably generated electricity (e.g., solar and wind) offers a promising means for reusing the CO 2 released during the production of cement, steel, and aluminum as well as the production of ammonia and methanol. If CO 2 could be removed from the atmosphere at acceptable costs (i.e., <$100/t of CO 2 ), then CO 2 R could be used to produce carbon-containing chemicals and fuels in a fully sustainable manner. Economic considerations dictate that CO 2 R current densities must be in the range of 0.1 to 1 A/cm 2 and selectivity toward the targeted product must be high in order to minimize separation costs. Industrially relevant operating conditions can be achieved by using gas diffusion electrodes (GDEs) to maximize the transport of species to and from the cathode and combining such electrodes with a solid-electrolyte membrane by eliminating the ohmic losses associated with liquid electrolytes. Additionally, high product selectivity can be attained by careful tuning of the microenvironment near the catalyst surface (e.g., the pH, the concentrations of CO 2 and H 2 O, and the identities of the cations in the double layer adjacent to the catalyst surface).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Composite battery separator

A composite battery separator comprises a support element (10) having an open pore structure such as a ribbed lattice and at least one liquid permeable sheet (20,22) to distribute the compressive force evenly onto the surfaces of the layers (24, 26) of negative active material and positive active material. In a non-flooded battery cell the compressible, porous material (18), such as a glass mat which absorbs the electrolyte, is compressed into a major portion of the pores or openings (16) in the support element. The unfilled pores in the material (18) form a gas diffusion path as the channels (41) formed between adjacent ribs in the lattice element (30,36). Facing two lattice elements (30, 31) with acute angled cross-ribs (34, 38) facing each other prevents the elements from interlocking and distorting a porous, separator (42) disposed between the lattice elements.

Edwards, Dean B.↗

LiWall Fusion - The New Concept of Magnetic Fusion

Utilization of the outstanding abilities of a liquid lithium layer in pumping hydrogen isotopes leads to a new approach to magnetic fusion, called the LiWall Fusion. It relies on innovative plasma regimes with low edge density and high temperature. The approach combines fueling the plasma by neutral injection beams with the best possible elimination of outside neutral gas sources, which cools down the plasma edge. Prevention of cooling the plasma edge suppresses the dominant, temperature gradient related turbulence in the core. Such an approach is much more suitable for controlled fusion than the present practice, relying on high heating power for compensating essentially unlimited turbulent energy losses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effect of hydrophilic treatment of microporous layer on fuel cell performance

The gas diffusion layer in a polymer electrolyte fuel cell is the component primarily responsible for effective water management under a wide variety of conditions. The incorporation of hydrophilic alumosilicate fibers in the microporous layer leads to an improvement in the fuel cell performance associated with a decrease in the mass transport resistance especially under high RH operation. This improvement in performance is obtained without sacrificing performance under low RH conditions. The alumosilicate fibers create domains that wick liquid water away from the catalyst layer. The improved mass transport performance is corroborated by AC impedance and neutron radiography analysis and is consistent with an increase in the average pore diameter inside the microporous layer.

30 DIRECT ENERGY CONVERSION↗

Laser nitriding for niobium superconducting radio-frequency accelerator cavities

Particle accelerators are a key tool for scientific research ranging from fundamental studies of matter to analytical studies at light sources. Cost-forperformance is critical, both in terms of initial capital outlay and ongoing operating expense, especially for electricity. It depends on the niobium superconducting radiofrequency (SRF) accelerator cavities at the heart of most of these machines. Presently Nb SRF cavities operate near 1.9 K, well (and expensively) below the 4.2 K atmospheric boiling point of liquid He. Transforming the 40 nm thick active interior surface layer from Nb to delta NbN (Tc = 17 K instead of 9.2 K) appears to be a promising approach. Traditional furnace nitriding appears to have not been successful for this. Further, exposing a complete SRF cavity to the time-temperature history required for nitriding risks mechanical distortion. Gas laser nitriding instead has been applied successfully to other metals [P.Schaaf, Prog. Mat. Sci. 47 (2002) 1]. The beam dimensions and thermal diffusion length permit modeling in one dimension to predict the time course of the surface temperature for a range of per-pulse energy densities. As with the earlier work, we chose conditions just sufficient for boiling as a reference point. We used a Spectra Physics HIPPO nanosecond laser (l = 1064 nm, Emax= 0.392 mJ, beam spot@ 34 microns, PRF =15 – 30 kHz) to obtain an incident fluence of 1.73 - 2.15 J/cm2 for each laser pulse at the target. The target was a 50 mm diameter SRF-grade Nb disk maintained in a nitrogen atmosphere at a pressure of 550 – 625 torr and rotated at a constant speed of 9 rpm. The materials were examined by scanning electron microscopy (SEM), electron probe microanalysis (EPMA) and x-ray diffraction (XRD). The SEM images show a sharp transition with fluence from a smooth, undulating topography to significant roughening, interpreted here as the onset of ablation. EPMA measurements of N/Nb atom ratio as a function of depth found a constant value to depths greater than the SRF active layer thickness. Certain irradiation conditions resulted in values consistent with formation of delta NbN. Under certain irradiation conditions, XRD data were consistent only with delta NbN on top of Nb metal. Funding: authored by Jefferson Science Associates LLC under US DOE Contract De-AC05-06OR23177. We are indebted to Prof. P. Schaaf (Goettingen) for the simulation code and helpful discussions.

36 MATERIALS SCIENCE↗

Transport and Energetics of Carbon Dioxide in Ionic Liquids at Aqueous Interfaces

A major hurdle in utilizing carbon dioxide (CO 2 ) lies in separating it from industrial flue gas mixtures and finding suitable storage methods that enable its application in various industries. To address this issue, we utilized a combination of molecular dynamics simulations and experiments to investigate the behavior of CO 2 in common room-temperature ionic liquids (RTIL) when in contact with aqueous interfaces. Here, our investigation of RTILs, [EMIM][TFSI] and [OMIM][TFSI], and their interaction with a pure water layer mimics the environment of a previously developed ultrathin enzymatic liquid membrane for CO 2 separation. We analyzed diffusion constants and viscosity, which reveals that CO 2 molecules exhibit faster mobility within the selected ILs compared to what would be predicted solely based on the viscosity of the liquids using the standard Einstein–Stokes relation. Moreover, we calculated the free energy of translocation for various species across the aqueous–IL interface, including CO 2 and HCO 3 – . Free energy profiles demonstrate that CO 2 exhibits a more favorable partitioning behavior in the RTILs compared to that in pure water, while a significant barrier hinders the movement of HCO 3 – from the aqueous layer. Experimental measurement of the CO 2 transport in the RTILs corroborates the model. These findings strongly suggest that hydrophobic RTILs could serve as a promising option for selectively transporting CO 2 from aqueous media and concentrating it as a preliminary step toward storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Plasma-Sprayed Refractory Oxide Coatings on Silicon-Base Ceramics

Silicon-base ceramics are promising candidate materials for high temperature structural applications such as heat exchangers, gas turbines and advanced internal combustion engines. Composites based on these materials are leading candidates for combustor materials for HSCT gas turbine engines. These materials possess a combination of excellent physical and mechanical properties at high temperatures, for example, high strength, high toughness, high thermal shock resistance, high thermal conductivity, light weight and excellent oxidation resistance. However, environmental durability can be significantly reduced in certain conditions such as when molten salts, H2 or water vapor are present. The oxidation resistance of silicon-base materials is provided by SiO2 protective layer. Molten salt reacts with SiO2 and forms a mixture of SiO2 and liquid silicate at temperatures above 800C. Oxygen diffuses more easily through the chemically altered layer, resulting in a catastrophic degradation of the substrate. SiC and Si3N4 are not stable in pure H2 and decompose to silicon and gaseous species such as CH4, SiH, SiH4, N2, and NH3. Water vapor is known to slightly increase the oxidation rate of SiC and Si3N4. Refractory oxides such as alumina, yttria-stabilized zirconia, yttria and mullite (3Al2O3.2SiO2) possess excellent environmental durability in harsh conditions mentioned above. Therefore, refractory oxide coatings on silicon-base ceramics can substantially improve the environmental durability of these materials by acting as a chemical reaction barrier. These oxide coatings can also serve as a thermal barrier. The purpose of this research program has been to develop refractory oxide chemical/thermal barrier coatings on silicon-base ceramics to provide extended temperature range and lifetime to these materials in harsh environments.

Tewari, Surendra↗

Hybrid nanocapsules for in situ TEM imaging of gas evolution reactions in confined liquids

Liquid cell transmission electron microscopy (TEM) enables the direct observation of dynamic physical and chemical processes in liquids at the nanoscale. Quantitative investigations into reactions with fast kinetics and/or multiple reagents will benefit from further advances in liquid cell design that facilitate rapid in situ mixing and precise control over reagent volumes and concentrations. This work reports the development of inorganic–organic nanocapsules for high-resolution TEM imaging of nanoscale reactions in liquids with well-defined zeptoliter volumes. These hybrid nanocapsules, with 48 nm average diameter, consist of a thin layer of gold coating a lipid vesicle. As a model reaction, the nucleation, growth, and diffusion of nanobubbles generated by the radiolysis of water is investigated inside the nanocapsules. When the nanobubbles are sufficiently small (10–25 nm diameter), they are mobile in the nanocapsules, but their movement deviates from Brownian motion, which may result from geometric confinement by the nanocapsules. Gases and fluids can be transported between two nanocapsules when they fuse, demonstrating in situ mixing without using complex microfluidic schemes. The ability to synthesize nanocapsules with controlled sizes and to monitor dynamics simultaneously inside multiple nanocapsules provides opportunities to investigate nanoscale processes such as single nanoparticle synthesis in confined volumes and biological processes such as biomineralization and membrane dynamics.

36 MATERIALS SCIENCE↗

Combustion Synthesis of Fullerenes and Fullerenic Nanostructures In Microgravity

The objectives of the proposed research were to determine the effects of gravity on fullerenes formation in flames and, based on the observed effects, to develop fundamental understanding of fullerenes formation and to identify engineering principles for fullerenes production. The research method consisted of the operation of laminar diffusion flames under normal- and reduced-gravity conditions, and the collection from the flames and subsequent analysis of condensables including any fullerenes present, using coupled high performance liquid chromatography/mass spectrometry and high resolution transmission electron microscopy. The focus included fullerene molecules C60 and C70 and fullerenic nanostructures including tubes, spherules and other shapes. The normal-gravity experiments were performed at MIT and complementary reduced-gravity experiments were to have been contributed by NASA. The independent variables of interest are gravity, fuel type, fuel/oxygen ratio, pressure, gas velocity at burner, diluent type and concentration. Given the large number of variables and the absence of data on either fullerene formation in diffusion flames or gravitational effects on fullerene formation in diffusion or premixed flames, the first part of the work was exploratory while the later part involved detailed study of the most interesting mechanisms. Samples of condensable material from laminar low pressure benzene/argon/oxygen diffusion flames were collected and analyzed by high-performance liquid chromatography to determine the yields of fullerenes, and by high-resolution transmission electron microscopy (HRTEM) to characterize the fullerenic material, i.e., curved-layer nanostructures, on and within the soot particles. The highest concentration of fullerenes was always detected just above the visible stoichiometric surface of a flame. The percentage of fullerenes in the condensable material increases with decreasing pressure. The overall highest amount of fullerenes was found for a surprisingly high dilution fuel with argon. The maximum flame temperature seems to be of minor importance in fullerene formation. The HRTEM analysis of the soot showed an increase of the curvature of the carbon layers, and hence increased fullerenic character. After this maximum, the curvature decreases. In addition to the soot, the samples included fullerenic nanostructures, such as tubes and spheroids including highly-ordered multilayered or onion-like structures. The soot itself shows highly ordered regions that appear to have been cells of ongoing fullerenic nanostructure formation.

Howard, Jack B.↗

Maximum CO 2 diffusion inside leaves is limited by the scaling of cell size and genome size

Maintaining high rates of photosynthesis in leaves requires efficient movement of CO 2 from the atmosphere to the mesophyll cells inside the leaf where CO 2 is converted into sugar. CO 2 diffusion inside the leaf depends directly on the structure of the mesophyll cells and their surrounding airspace, which have been difficult to characterize because of their inherently three-dimensional organization. Yet faster CO 2 diffusion inside the leaf was probably critical in elevating rates of photosynthesis that occurred among angiosperm lineages. Here we characterize the three-dimensional surface area of the leaf mesophyll across vascular plants. We show that genome size determines the sizes and packing densities of cells in all leaf tissues and that smaller cells enable more mesophyll surface area to be packed into the leaf volume, facilitating higher CO 2 diffusion. Measurements and modelling revealed that the spongy mesophyll layer better facilitates gaseous phase diffusion while the palisade mesophyll layer better facilitates liquid-phase diffusion. Our results demonstrate that genome downsizing among the angiosperms was critical to restructuring the entire pathway of CO 2 diffusion into and through the leaf, maintaining high rates of CO 2 supply to the leaf mesophyll despite declining atmospheric CO 2 levels during the Cretaceous.

59 BASIC BIOLOGICAL SCIENCES↗

Understanding the Role of Interfaces for Water Management in Platinum Group Metal-Free Electrodes in Polymer Electrolyte Fuel Cells

For this study, a systematic analysis, both experimental and model-assisted, has been performed over three main configurations of platinum group metal-free (PGM-free) electrodes in polymer electrolyte fuel cells (PEFCs): Catalyst-coated membrane CCM technology is being compared to the gas-diffusion electrode (GDE) method of electrode fabrication and juxtaposed to a hybrid/combined GDE-CCM method of membrane-electrode assembly (MEA) fabrication. The corresponding electrodes were evaluated for their electrochemical performance, modeled, and studied with in situ and operando X-ray computed tomography (X-ray CT). The study establishes that through-thickness inhomogeneities play the most important role in water withdrawal/water management and affect most significantly PGM-free PEFC performance. The catalyst integration technique results in formation of interfacial regions with increased porosity and surface roughness. These regions form critical interfaces de facto responsible for flooding type behavior of the PEFC as shown for a first time by operando X-ray CT. The computational model shows that the PEFC performance critically depends on liquid water formation and transport at cold and wet conditions.

25 ENERGY STORAGE↗

Tritium release from SS316 under vacuum condition

The plasma facing surface of the ITER vacuum vessel, partly made of low carbon austenitic stainless steel type 316L, will incorporate tritium during machine operation. In this paper the kinetics of tritium release from stainless steel type 316 into vacuum and into a noble gas stream are compared and modelled. Type 316 stainless steel specimens loaded with tritium either by exposure to 1.2 kPa HT at 573 K or submersion into liquid HTO at 298 K showed characteristic thin surface layers trapping tritium in concentrations far higher than those determined in the bulk. The evolution of the tritium depth profile in the bulk during heating under vacuum was non-discernible from that of tritium liberated into a stream of argon. Only the relative amount of the two released tritium-species, i.e. HT or HTO, was different. Temperature-dependent depth profiles could be predicted with a one-dimensional diffusion model. Diffusion coefficients derived from fitting of the tritium release into an evacuated vessel or a stream of argon were found to be (1.4 ± 1.0)*10{sup -7} and (1.3 ± 0.9)*10{sup -9} cm{sup 2}/s at 573 and 423 K, respectively. Polished surfaces on type SS316 stainless steel inhibit considerably the thermal release rate of tritium.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Effects of Be doping on InP nanowire growth mechanisms

Be-doped InP nanowires were grown by the gold-assisted vapour-liquid-solid mechanism in a gas source molecular beam epitaxy system. The InP nanowire length versus diameter [L(D)] dependence revealed an unexpected transition with increasing Be dopant concentration. At Be dopant concentration below {approx}10{sup 18} cm{sup -3}, nanowires exhibited the usual inverse L(D) relationship, indicating a diffusion-limited growth regime. However, as dopant concentration increased, the nanowire growth rate was suppressed for small diameters, resulting in an unusual L(D) dependence that increased before saturating in height at about 400 nm. The cause of this may be a change in the droplet chemical potential, introducing a barrier to island nucleation. We propose a model accounting for the limitations of diffusion length and monolayer nucleation to explain this behaviour.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Investigation of the feasibility of developing low permeability polymeric films

The feasibility of reducing the gas permeability rate of Mylar and Kapton films without drastically effecting their flexibility characteristics at cryogenic temperatures was considered. This feasibility was established using a concept of diffusion bonding two layers of metallized films together forming a film-metal-film sandwich laminate. The permeability of kapton film to gaseous helium was reduced from a nominal ten = to the minus 9 power cc-mm/sq cm sec. cm Hg to ten to the minus 13 power cc-mm/ sq cm - sec. cm Hg with some values as low as ten to the minus 15 power cc - mm/sq cm m-sec - cm Hg being obtained. Similar reductions occurred in the liquid hydrogen permeability at -252 C. In the course of the program the permeability, flexibility and bond strength of plain, metalized and diffusion bond film were determined at +25 C, -195 C and -252 C. The cryogenic flexibility of Kapton film was reduced slightly due to the metallization process but no additional loss in flexibility resulted from the diffusion bonding process.

Hoggatt, J. T.↗

Plasma-droplet interaction study to assess transport limitations and the role of • OH, O • ,H • ,O 2 (a 1 Δ g ),O 3 , He(2 3 S) and Ar(1s 5 ) in formate decomposition

Plasmas interacting with liquid microdroplets are gaining momentum due to their ability to significantly enhance the reactivity transfer from the gas phase plasma to the liquid. This is, for example, critically important for efficiently decomposing organic pollutants in water. In this contribution, the role of •OH as well as non-•OH-driven chemistry initiated by the activation of small water microdroplets in a controlled environment by diffuse RF glow discharge in He with different gas admixtures (Ar, O 2 and humidified He) at atmospheric pressure is quantified. The effect of short-lived radicals such as O• and H• atoms, singlet delta oxygen (O 2 (a 1 Δ g )), O 3 and metastable atoms of He and Ar, besides •OH radicals, on the decomposition of formate dissolved in droplets was analyzed using detailed plasma diagnostics, droplet characterization and ex situ chemical analysis of the treated droplets. The formate decomposition increased with increasing droplet residence time in the plasma, with ~70% decomposition occurring within ~15 ms of the plasma treatment time. The formate oxidation in the droplets is shown to be limited by the gas phase •OH flux at lower H 2 O concentrations with a significant enhancement in the formate decomposition at the lowest water concentration, attributed to e – /ion-induced reactions. However, the oxidation is diffusion limited in the liquid phase at higher gaseous •OH concentrations. Here, the formate decomposition in He/O 2 plasma was similar, although with an order of magnitude higher O• radical density than the •OH density in the corresponding He/H 2 O plasma. Using a one-dimensional reaction–diffusion model, we showed that O 2 (a 1 Δ g ) and O 3 did not play a significant role and the decomposition was due to O•, and possibly •OH generated in the vapor containing droplet-plasma boundary layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗