Search NASA⌕ Search

SEARCH · Search NASA

Results for “low gain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Galileo Satellite Tour: Orbit Determination

This paper discusses orbit determination results for the Galileo satellite tour. Lacking a high gain antenna, the mission will use a low gain antenna for communication and tracking. This change implies far less navigation data will be available than previously expected. A baseline orbit analysis was completed assuming this decreased data schedule. Variations on this baseline were studied to determine sensitivity to data loss. Results indicate that the probability of completing the tour is less than 90 percent, although future improvements in orbit determination promise to raise the probability of completion above 90 percent.

Haw, R. J.↗
NASA NTRS2009

Quantification of Trace Chemicals Using Vehicle Cabin Atmosphere Monitor

A system to monitor the concentrations of trace chemicals in cabin atmosphere is one of the most critical components in long-duration human flight missions. The Vehicle Cabin Atmosphere Monitor (VCAM) is a miniature gas chromatograph mass spectrometer system to be used to detect and quantify trace chemicals in the International Space Station. We developed an autonomous computational process to quantify trace chemicals for use in VCAM. The process involves the design of a measured signal quantification scheme, the construction of concentration curves (i.e. the relationship between concentration and ion count measured by VCAM), the decision rule of applying high- or low-gain concentration curves, and the detection of saturation, low-signals, and outliers. When the developed quantification process is applied, the average errors of concentration for most of trace chemicals are found to be between 14% and 66%.

Lee, Seungwon↗
NASA NTRS1993

Mobile antenna development at JPL

The Jet Propulsion Laboratory (JPL), under the sponsorship of NASA, has pioneered the development of land vehicle antennas for commercial mobile satellite communications. Several novel antennas have been developed at L-band frequencies for the Mobile Satellite (MSAT) program initiated about a decade ago. Currently, two types of antennas are being developed at K- and Ka-band frequencies for the ACTS (Advanced Communications Technology Satellite) Mobile Terminal (AMT) project. For the future, several hand-held antenna concepts are proposed for the small terminals of the Ka-band Personal Access Satellite System (PASS). For the L-band MSAT program, a number of omni-directional low-gain antennas, such as the crossed drooping-dipoles, the higher-order-mode circular microstrip patch, the quadrifilar helix, and the wrapped-around microstrip 'mast' array, have been developed for lower data rate communications. Several medium-gain satellite tracking antennas, such as the electronically scanned low-profile phased array, the mechanically steered tilted microstrip array, the mechanically steered low-profile microstrip Yagi array, and the hybrid electronically/mechanically steered low-profile array, have been developed for the MSAT's higher data rate and voice communications. To date, for the L-band vehicle application, JPL has developed the world's lowest-profile phased array (1.8 cm height), as well as the lowest-profile mechanically steered antenna (3.7 cm height). For the 20/30 GHz AMT project, a small mechanically steered elliptical reflector antenna with a gain of 23 dBi has recently been developed to transmit horizontal polarization at 30 GHz and receive vertical polarization at 20 GHz. Its hemispherical radome has a height of 10 cm and a base diameter of 23 cm. In addition to the reflector, a mechanically steered printed MMIC active array is currently being developed to achieve the same electrical requirements with a low profile capability. These AMT antenna developments, along with other Ka-band technologies, will lead to the development of several compact hand-held terminals for the PASS program. A few antenna concepts, such as the lap-top or desk-top terminal's printed array, the hand-held phased array, and the head-mounted low-profile array, have been proposed to achieve a future vision for the personal access communications system.

Huang, J.↗
NASA NTRS1987

Performance characteristics of omnidirectional antennas for spacecraft using NASA networks

Described are the performance capabilities and critical elements of the shaped omni antenna developed for NASA for space users of NASA networks. The shaped omni is designed to be operated in tandem for virtually omnidirectional coverage and uniform gain free of spacecraft interference. These antennas are ideal for low gain data requirements and emergency backup, deployment, amd retrieval of higher gain RF systems. Other omnidirectional antennas that have flown in space are described in the final section. A performance summary for the shaped omni is in the Appendix. This document introduces organizations and projects to the shaped omni applications for NASA's space use. Coverage, gain, weight, power, and implementation and other performance information for satisfying a wide range of data requirements are included.

Hilliard, Lawrence M.↗
NASA NTRS1995

Galileo Press Conference from JPL

The press conference concerns the Orbiter Deflection maneuver that had taken place earlier that day. The participants in the press conference, spoke of the success of the maneuver, which was performed perfectly. The Galileo project was a cooperative effort with the German Space Agency. Two members of the German Space Agency were introduced. There was a review of the trip to Jupiter, and the probe release. The deflection maneuver was important to getting the Probe on the correct path for the descent into the atmosphere of Jupiter. A brief video showed simulations of the probe release and the descent of the probe into the atmosphere. There was discussion about the failure of the high gain antenna to deploy, and the requirement to use the low gain antenna instead. A full scale model of the probe was shown.

Source record↗
NASA NTRS1988

MSAT-X phased array antenna adaptions to airborne applications

The Mobile Satellite Experiment (MSAT-X) phased array antenna is being modified to meet future requirements. The proposed system consists of two high gain antennas mounted on each side of a fuselage, and a low gain antenna mounted on top of the fuselage. Each antenna is an electronically steered phased array based on the design of the MSAT-X antenna. A beamforming network is connected to the array elements via coaxial cables. It is essential that the proposed antenna system be able to provide an adequate communication link over the required space coverage, which is 360 degrees in azimuth and from 20 degrees below the horizon to the zenith in elevation. Alternative design concepts are suggested. Both open loop and closed loop backup capabilities are discussed. Typical antenna performance data are also included.

Sparks, C.↗
NASA NTRS2012

Characterization of NPP Visible/Infrared Imager Radiometer Suite (VIIRS) Reflective Solar Bands Dual Gain Anomaly

The Visible/Infrared Imager Radiometer Suite (VIIRS) contains six dual gain bands in the reflective solar spectrum. The dual gain bands are designed to switch gain mode at pre-defined thresholds to achieve high resolution at low radiances while maintaining the required dynamic range for science. During pre-launch testing, an anomaly in the electronic response before transitioning from high to low gain was discovered and characterized. On-orbit, the anomaly was confirmed using MODIS data collected during Simultaneous Nadir Overpasses (SNOs). The analysis of the Earth scene data shows that dual gain anomaly can be determined at the orbital basis. To characterize the dual gain anomaly, the anomaly region and electronic offsets were tracked per week during the first 8 month of VIIRS operation. The temporal analysis shows the anomaly region can drift ~20 DN and is impacted by detectors DC Restore. The estimated anomaly flagging regions cover ~2.5 % of the high gain dynamic range and are consistent with prelaunch and on-orbit LUT. The prelaunch results had a smaller anomaly range (30-50 DN) and are likely the results of more stable electronics from the shorter data collection time. Finally, this study suggests future calibration efforts to focus on the anomaly's impact on science products and possible correction method to reduce uncertainties.

Lee, Shihyan↗
NASA NTRS2018

High-Rate Ka-Band Modulator for the NISAR Mission

In order to meet ever-increasing data return requirements, more satellites are using the near-Earth Ka-band (25.5 – 27.0 GHz) to achieve higher downlink rates. The paper discusses the Universal Space Transponder - Ka-band Modulator (UST-KaM) developed at the NASA Jet Propulsion Laboratory for the NASA-ISRO SAR (NISAR) mission, which is capable of transmitting up to 1.74 Gbps with 7/8 LDPC encoding. The UST-KaM utilizes OQPSK with both baseband and RF filtering to contain the 1 Gsps transmission spectrum within the 1.5 GHz Ka-band, even with the use of an external, saturated amplifier. Due to the high data rates involved, several technical hurdles were overcome in both the digital and RF designs. The UST-KaM is a software defined radio with two digital circuit board assemblies: a low speed housekeeper board for commanding and telemetry, and a high-rate signal processing board known as the Signal Processing Module (SPM). The SPM receives data from the spacecraft via a SERDES interface at up to 2 Gbps, processes and encodes the data using a Xilinx Virtex-5 FPGA, and produces 1 Gsps OQPSK I and Q waveforms via synchronized, multiplexed DACs. The RF Electronics in the UST-KaM employ a heterodyne architecture in which the I/Q digital waveforms are filtered and then up-converted using a sub-harmonic IQ mixer. The LO of the converter, which is included in the exciter assembly, is at 13.125GHz, and the RF output is a 26.25GHz carrier which is modulated with the OQPSK waveforms. The output of the mixer is then filtered using low loss quartz thinfilm edge coupled Chebyshev filters and amplified through a series of low gain Ka-Band amplifiers. The exciter assembly also has a 2GHz, low-phase-noise, PLL synthesizer to supply the clock to the DACs for the high rate digital waveforms.

Spurgers, Carl↗
NASA NTRS1996

Automated Operations for Galileo Communications

Following the deployment failure of Galileo's high gain antenna, the downlink had to be redesigned so as to effectively use the low gain antenna. The downlink was redesigned to maximize the data return and increase the reliability which required the reconfiguration of the onboard software and the deep space network. The revised downlink features: data compression; antenna arraying; the recoding and reprocessing of telemetry; suppressed carrier tracking, and error-correction coding. The deep space network Galileo telemetry (DGT) subsystem was developed and deployed at three sites in Australia, Spain and the U.S. The DGT was designed as an automated system that continuously monitors and adjusts its parameters and environment in response to either pre-loaded sequences or changes in the internal status.

Statman, Joseph I.↗
NASA NTRS1992

Galileo completing VEEGA - A mid-term report

In December Galileo will complete its Venus-Earth-Earth-Gravity Assist (VEEGA) mission phase and will be placed on a direct trajectory to Jupiter arriving in December 1995. Galileo will be the first aircraft to orbit Jupiter and send a probe into its atmosphere and will perform an intensive and comprehensive investigation of the planet. Observations made during the October 1991 encounter with the asteroid Gaspra are discussed. The observation plan to be used for earth and moon observations during the December 1992 gravity assist encounter is described. The Galileo High-Gain Antenna (HGA) deployment anomaly status is reported and future corrective actions are outlined. The low-gain antenna contingency mission to be implemented if the HGA cannot be deployed is described and overall performance and status of the space craft are discussed. The selected tour for the Galileo Jupiter satellite-gravity-assist orbital tour is described and the decision rationale for performing the August 1993 asteroid Ida flyby option is presented.

O'Neil, William J.↗
NASA NTRS1994

Galileo System Design for Orbital Operations

In April 1991, Galileo's X-band high gain antenna failed to deploy. An alternate approach which utilizes the spacecraft's S-band low gain antenna was conceived and is in development. This approach will enable the accomplishment of at least 70 percent of Galileo's original scientific objectives. The short development period dictates that the spacecraft system design, the ground data system design, and the operational system scenarios and procedures necessary to conduct the mission be developed concurrently, and places a premium on validating the system designs as early as possible. This paper presents an overview of the Galileo Mission, briefly describes the changes required to implement the orbital phase of the Galileo Mission, and describes the functional model of the end to end system which was developed to support the systems design effort.

Galileo↗
NASA NTRS1994

Galileo System Design for Orbital Operations

In April 1991, Galileo's X-band high gain antenna failed to deploy. An alternate approach which utilizes the spacecraft's S-band low gain antenna was conceived and is in development.

Galileo↗
NASA NTRS1975

The effects of stability augmentation on the gust response of a STOL aircraft during a curved manual approach

The task of investigating the effect of SAS was formulated as two optimal control problems for stochastic systems: (1) to compute SAS gains with a rate model in the performance index algorithm; and (2) to calculate the pilot gains and system gust response using an optimal pilot model. Both problems were solved to yield reasonable low gains for the pilot and SAS, and the lateral directional mode poles and the longitudinal short period poles could be placed accurately by the model matching algorithm. Of the longitudinal (SAS) poles achieved, the vertical rms path error was least for the unaugmented poles. The lateral rms path error was an order of magnitude larger than the vertical error and showed a plus or minus 50 percent variation with SAS. It increased with dutch roll frequency and damping, and it decreased most significantly with increased roll stability. The variation in lateral error with bank angle for curved flight was also a significant function of the augmented poles.

Porter, M. B., Jr.↗
NASA NTRS1987

Effect of Gimbal friction modeling technique on control stability and performance for Centaur upper-stage

The powered-phase autopilot for the Centaur upper stage rocket uses an autopilot forward loop gain scheduler that decreases the proportional gain as propellant mass is depleted. Nonlinear time response simulation studies revealed that Centaur vehicles with low-gain autopilots would have large attitude error limit cycles. These limit cycles were due to the assumed presence of Coulomb friction in the engine gimbals. This situation could be corrected through the use of an harmonic dither, programmed into the on-board digital computer and added to the engine command signal. This would introduce impending motion to the engines, allowing control of the engines even under small commands. Control authority was found to be restored when dither was used. A concern arose that the Centaur could be unacceptably excited at resonances near the dither frequency, if the dither amplitude was to be chosen on the basis of friction level present, a test was conducted to measure this level. Dither characteristics were to be based on the test results. The test results showed that the gimbal friction characteristic was actually hysteretic rather than the assumed Coulomb friction. The simulation results showed that, using this new model of gimbal friction, dither would no longer be necessary.

Graham, Ronald E.↗
NASA NTRS1987

Effect of gimbal friction modelling technique on control stability and performance for Centaur upper stage

The powered-phase autopilot for the Centaur upper stage rocket uses an autopilot forward loop gain scheduler that decreases the proportional gain as propellant mass is depleted. Nonlinear time response simulation studies revealed that Centaur vehicles with low-gain autopilots would have large attitude error limit cycles. These limit cycles were due to the assumed presence of Coulomb friction in the engine gimbals. This situation could be corrected through the use of an harmonic dither, programmed into the on-board digital computer and added to the engine command signal. This would introduce impending motion to the engines, allowing control of the engines even under small commands. Control authority was found to be restored when dither was used. A concern arose that the Centaur could be unacceptably excited at resonances near the dither frequency, if the dither amplitude was to be chosen on the basis of friction level present, a test was conducted to measure this level. Dither characteristics were to be based on the test results. The test results showed that the gimbal friction characteristic was actually hysteretic rather than the assumed Coulomb friction. The simulation results showed that, using this new model of gimbal friction, dither would no longer be necessary.

Graham, Ronald E.↗
NASA NTRS1991

Gain and energy storage in holmium YLF

It is demonstrated that Q-switched holmium lasers are capable of high-gain and high-energy operation at 300 K. Small-signal gain coefficients of 0.50 and 0.12/cm have been measured in YLF and YAG, respectively. Small-signal gains of 0.50/cm are comparable to those achievable in Nd:YAG and are not typical of low-gain materials. This large gain in the Ho:YLF material is made possible by operating the amplifier in the ground state depletion mode. The amplifier performance data and associated analysis presented demonstrate that efficient energy storage is possible with very high excited state ion densities of the Ho 5I7 upper laser level. This is an important result since upconversion can limit the 5I7 population. Although upconversion was still present in this experiment, it was possible to achieve efficient energy storage, demonstrating that the problem is manageable even at high excitation densities in YLF.

Storm, Mark E.↗