Search NASA⌕ Search

SEARCH · Search NASA

Results for “low temperature chlorination”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Rechargeable Al/Cl2 battery with molten AlCl4/-/ electrolyte.

A molten salt system based on Al- and Cl2 carbon electrodes, with an AlCl3 alkali chloride eutectic as electrolyte, offers promise as a rechargeable, high energy density battery which can operate at a relatively low temperature. Electrode kinetic studies showed that the electrode reactions at the Al anode were rapid and that the observed passivation phenomena were due to the formation at the electrode surface of a solid salt layer resulting from concentration changes on anodic or cathodic current flow. It was established that carbon electrodes were intrinsically active for chlorine reduction in AlCl3-alkali chloride melts. By means of a rotating vitreous carbon disk electrode, the kinetic parameters were determined.

Holleck, G. L.↗
NASA NTRS1983

Development of a radiation-hard CMOS process

It is recommended that various techniques be investigated which appear to have the potential for improving the radiation hardness of CMOS devices for prolonged space flight mission. The three key recommended processing techniques are: (1) making the gate oxide thin. It has been shown that radiation degradation is proportional to the cube of oxide thickness so that a relatively small reduction in thickness can greatly improve radiation resistance; (2) cleanliness and contamination control; and (3) to investigate different oxide growth (low temperature dry, TCE and HCL). All three produce high quality clean oxides, which are more radiation tolerant. Technique 2 addresses the reduction of metallic contamination. Technique 3 will produce a higher quality oxide by using slow growth rate conditions, and will minimize the effects of any residual sodium contamination through the introduction of hydrogen and chlorine into the oxide during growth.

Power, W. L.↗
DOE OSTI2026

Low resistance p-type contacts to monolayer WSe2 through chlorinated solvent doping

Tungsten diselenide (WSe 2 ) is a promising p-type semiconductor limited by high contact resistance (R C ) and the lack of a reliable doping strategy. Here, we demonstrate that exposing WSe 2 to chloroform provides simple and stable p-type doping. In monolayer WSe 2 transistors with Pd contacts, chloroform increases the maximum hole current by over 100× (>200 µA/µm), reduces R C to ~ 2.5 kΩ·μm, and retains an on/off ratio of 10 10 at room temperature. These improvements persist for over 8 months, survive a 150 °C thermal anneal, and remain effective down to 10 K, enabling a cryogenic R C of ~ 1 kΩ·μm. Density functional theory indicates that chloroform strongly physisorbs to WSe 2 , inducing hole doping with minimal impact on the electronic states between the valence band and conduction band edges. Auger electron spectroscopy and atomic force microscopy suggest that chloroform intercalates at the WSe 2 interface with the gate oxide, contributing to doping stability and mitigating interfacial dielectric disorder, though further studies are needed to conclusively confirm this mechanism. This robust, scalable approach enables high-yield WSe 2 transistors with good p-type performance.

42 ENGINEERING↗
DOE OSTI2020

Methylammonium Lead Tribromide Single Crystal Detectors towards Robust Gamma-Ray Photon Sensing

In recent years, hybrid perovskite single crystalline solid-state detectors have shown promise in γ-ray spectroscopy. Here, the γ-ray photon induced electrical pulses are investigated, which are produced by perovskite solid-state detectors made with the commonly used methylammonium lead tribromide crystals with chlorine incorporation. Under low electric field detector operation, slow pulses generated by γ-rays with average rise times of 65 µs are observed, which decreases to 20 µs when a higher electrical field of 500 V cm -1 is applied. However, the baseline becomes noisy quickly, which prevents collection of clean pulses for spectra construction. Further, by systematically measuring the temperature dependence and current–voltage characteristics, such instability is attributed to the local ion migration under electrical field creating a fluctuating dark noise, which presents a major challenge in perovskite γ-ray detector technologies. It is demonstrated that cycling the bias between positive and negative polarity can stabilize the detector, allowing for longer periods of pulse accumulation for generating energy resolved spectra with resolutions of ≈35% at 59.6 keV and ≈25% at 662 keV at room temperature. The study indicates that the main limiting factors of perovskite-based γ-ray detectors are slow rise times and bias instability. Finally, these challenges must be properly addressed to achieve reproducible, high-resolution γ-ray detection.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Surface chlorination of IrO2(110) by HCl

The ability to controllably chlorinate metal-oxide surfaces can provide opportunities for designing selective oxidation catalysts. In the present study, we investigated the surface chlorination of IrO2(110) by HCl using temperature programmed reaction spectroscopy (TPRS), x-ray photoelectron spectroscopy (XPS), and density functional theory (DFT) calculations. We find that exposing IrO2(110) to HCl, followed by heating to 650 K in ultrahigh vacuum, produces nearly equal quantities of on-top and bridging Cl atoms on the surface, Clt and Clbr, where the Clbr atoms replace O-atoms that are removed from the surface by H2O formation. After HCl adsorption at 85 K, only H2O desorbs at low Cl coverages during TPRS, but HCl begins to desorb in increasing yields as the Cl coverage is increased above about 0.5 monolayer (ML). The desorption of Cl2 was not observed under any conditions, in good agreement with the high barrier for this reaction predicted by DFT. A maximum Cl coverage of 1 ML, with nearly equal coverages of Clt and Clbr atoms, could be generated by reacting HCl with IrO2(110) in UHV. Our results suggest that a kinetic competition between recombinative HCl and H2O desorption under the conditions studied limits the saturation Cl coverage to a value less than the 2 ML maximum predicted by thermodynamics. XPS further shows that the partitioning of Cl between the Clt and Clbr states can be altered by subjecting partially chlorinated IrO2(110) to reductive or oxidative treatments, demonstrating that the Cl site population can change dynamically in response to the gas environment. Our results provide insights for understanding the chlorination of IrO2(110) by HCl and can enable future experimental studies to determine how Cl-modification alters the surface chemical reactivity of IrO2(110) and potentially enhances selectivity toward partial oxidation chemistry.

Chemistry↗
NASA NTRS2011

Two Catalysts for Selective Oxidation of Contaminant Gases

Two catalysts for the selective oxidation of trace amounts of contaminant gases in air have been developed for use aboard the International Space Station. These catalysts might also be useful for reducing concentrations of fumes in terrestrial industrial facilities especially facilities that use halocarbons as solvents, refrigerant liquids, and foaming agents, as well as facilities that generate or utilize ammonia. The first catalyst is of the supported-precious-metal type. This catalyst is highly active for the oxidation of halocarbons, hydrocarbons, and oxygenates at low concentrations in air. This catalyst is more active for the oxidation of hydrocarbons and halocarbons than are competing catalysts developed in recent years. This catalyst completely converts these airborne contaminant gases to carbon dioxide, water, and mineral acids that can be easily removed from the air, and does not make any chlorine gas in the process. The catalyst is thermally stable and is not poisoned by chlorine or fluorine atoms produced on its surface during the destruction of a halocarbon. In addition, the catalyst can selectively oxidize ammonia to nitrogen at a temperature between 200 and 260 C, without making nitrogen oxides, which are toxic. The temperature of 260 C is higher than the operational temperature of any other precious-metal catalyst that can selectively oxidize ammonia. The purpose of the platinum in this catalyst is to oxidize hydrocarbons and to ensure that the oxidation of halocarbons goes to completion. However, the platinum exhibits little or no activity for initiating the destruction of halocarbons. Instead, the attack on the halocarbons is initiated by the support. The support also provides a high surface area for exposure of the platinum. Moreover, the support resists deactivation or destruction by halogens released during the destruction of halocarbons. The second catalyst is of the supported- metal-oxide type. This catalyst can selectively oxidize ammonia to nitrogen at temperatures up to 400 C, without producing nitrogen oxides. This catalyst converts ammonia completely to nitrogen, even when the concentration of ammonia is very low. No other catalyst is known to oxidize ammonia selectively at such a high temperature and low concentration. Both the metal oxide and the support contribute to the activity and selectivity of this catalyst.

Wright, John D.↗
DOE OSTI2020

Development of metallic nuclear material purification process via simultaneous chlorination and volatilization

Here, a purification process involving simultaneous chlorination and volatilization is reported using aluminum, iron, gallium, and uranium separation from cerium metal as the demonstration system. Anhydrous Cl 2 gas was reacted with the metal after it had been converted to small particles of hydride at temperatures ranging from 523 to 973 K. Each of the impurities should form chlorides with relatively high saturated vapor pressures. The objective of the process was to volatilize these chlorides after first achieving near-complete conversion of the metals to hydride and then chlorides. Complete conversion of hydrides to chlorides could not be achieved using relatively low-grade (99.5%) Cl 2 . High decontamination factors for all of the metal impurities required near complete conversion to chloride. It was concluded that oxygen contamination of the feed gas stream likely limits the conversion to chlorides by forming oxides instead, which then limits the volatilization of contaminants. Uranium was particularly challenging to remove in experiments suspected of having high oxygen contamination in the feed gas stream. After switching to ultra-high purity (99.999%) Cl 2 , complete conversion to chlorides within the measurement error was possible for the entire temperature range studied. Decontamination factors for aluminum, iron, gallium, and uranium were found to have average values of 1.9, 9.8, 14, and 5, respectively, at 973 K. While the process was most extensively studied using a once-through gas flow, recycling unreacted Cl 2 gas succeeded at minimizing waste while still maintaining complete conversion and similar decontamination factors.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

In Situ High-Temperature TEM Observation of Inconel Corrosion by Molten Chloride Salts with N 2 , O 2 , or H 2 O

Here, in situ transmission electron microscopy (TEM) diffraction and imaging techniques are used to monitor and quantify corrosion of Inconel-625 by pure molten chloride salts (MgCl 2 – NaCl – KCl) at 500 °C–800 °C in 1.0 atm inert N 2 or pure O2, or by salts which are controllably hydrated in a high vacuum chamber. The isothermal corrosion rate R in inert N 2 increases from 203 ± 30 μ m year –1 at 700 °C to 463 ± 30 μ m year –1 at 800 °C. An oxygen ambient causes a six-fold increase to R = 1261 ± 170 μ m year –1 at 700 °C. Salt hydration dramatically accelerates corrosion to R > 3 × 10 5 μ m year –1 at 700 °C while it leads to a more moderate R = 95 ± 20 and 486 ± 30 μ m year –1 at 500 °C and 600 °C, respectively. These isothermal corrosion rates indicate that the molten chloride corrosion is significantly accelerated by salt hydration at temperatures above 600 °C, where corrosion is aggravated by increased generation and solubility of corrosive HCl gases. Hence, to reduce rate of corrosion it is important to both avoid incorporation of H 2 O into the system at each stage and ensure proper flushing of the system before increasing the temperature beyond 600 °C. Compositional analysis of the corroded cells indicate that corrosion in O 2 ambient is dominated by oxidation of metals by O 2 gas dissolved in the chloride melt, but corrosion in H 2 O ambients is caused by chlorination of metals by dissolved HCl gas and MgOH + ions. So, to reduce rate of corrosion, steps should be taken to tailor chloride melt compositions that has low solubility for HCl and O 2 . All of our corroded samples exhibit passive-protective oxide layers of Cr, Mg, and Ni. In addition, distinct volatile compounds of Ni, Mo and Cr involving NiCl 2 , (Na,K) 2 MoO 4 and CrO 2 (OH) 2 are detected in N 2 , H 2 O, and O 2 ambients, respectively. We believe that corrosion acceleration can be minimized by minimizing formation of volatile by-products or promoting reactions that could convert these volatile compounds to solid phases, as these volatile compounds led to destruction of protective oxide layers.

14 SOLAR ENERGY↗
DOE OSTI2025

Novel Electrowinning Reactor for the Energy-Efficient, Low- Cost Production of Rare Earth Metals

This project developed a novel neodymium (Nd) electrowinning reactor for energy-efficient electrowinning of Nd metal. Throughout this project we have developed an alternative chloride based molten salt electrolysis process. Our process lowers the specific electrical energy consumption compared to the state of the art, while producing reusable chlorine gas and eliminating direct CO2 and PFC emissions. Facilities required for implementing the project were setup and designs were finalized, and a standard operating procedure for safe operation of high temperature electrolysis cells was written. The electrowinning reactor was designed and constructed. Electrolysis experiments confirmed the ability to reproducibly electrowin Nd metal on a Mo cathode. The current efficiency for Nd electrowinning was measured as a function of applied current density in the presence of the separator. Successful electrowinning of Nd sponge at high current densities (200 mA/cm2 and above) at a current efficiency >80% was demonstrated using multiple techniques. Stable Nd electrowinning up to 10h at 250 mA/cm2 was demonstrated. All of these design advancements were used to develop a techno-economic and life cycle assessment model that demonstrated that our process could be operated at cost of less than $0.20/kg-Nd (~30% lower compared to state of the art when comparing electrolysis energy cost) with a >20% total reduction in global warming potential compared to the state of the art while generating no direct CO2 or perfluorocarbon emissions.

42 ENGINEERING↗
NASA NTRS2009

Carbon Nanotube Based Chemical Sensors for Space and Terrestrial Applications

A nanosensor technology has been developed using nanostructures, such as single walled carbon nanotubes (SWNTs), on a pair of interdigitated electrodes (IDE) processed with a silicon-based microfabrication and micromachining technique. The IDE fingers were fabricated using photolithography and thin film metallization techniques. Both in-situ growth of nanostructure materials and casting of the nanostructure dispersions were used to make chemical sensing devices. These sensors have been exposed to nitrogen dioxide, acetone, benzene, nitrotoluene, chlorine, and ammonia in the concentration range of ppm to ppb at room temperature. The electronic molecular sensing of carbon nanotubes in our sensor platform can be understood by intra- and inter-tube electron modulation in terms of charge transfer mechanisms. As a result of the charge transfer, the conductance of p-type or hole-richer SWNTs in air will change. Due to the large surface area, low surface energy barrier and high thermal and mechanical stability, nanostructured chemical sensors potentially can offer higher sensitivity, lower power consumption and better robustness than the state-of-the-art systems, which make them more attractive for defense and space applications. Combined with MEMS technology, light weight and compact size sensors can be made in wafer scale with low cost. Additionally, a wireless capability of such a sensor chip can be used for networked mobile and fixed-site detection and warning systems for military bases, facilities and battlefield areas.

Li, Jing↗
DOE OSTI2024

Macroscale properties and atomic-scale mechanisms of ash removal in low-temperature hydrothermal carbonization

Biogenic ash is a significant impediment to the utilization of agricultural residues in biofuel production. Such challenge can be addressed by various treatments, as demonstrated in this study on the experimental and computational mechanisms involved in the hydrothermal treatment (HT) of wheat straw. A combination of classical (all-atom) molecular dynamics simulations of cellulose carrying silica and calcium species, along with first principles quantum chemical calculations, indicates the dissociation of inorganics from the cellulose with increased HT temperature. Here, this observation is confirmed by experimental evidence of effective ash removal by HT, showing at least 50% removal of sulfur, chlorine, potassium, and calcium, and 12.5% of silica, leading to a reduced total ash content (from 6.7% to 4.2%).Changes in structural features upon HT, such as surface cellular structure and porosity, were revealed, accompanied by an increased specific surface area (from 1.17 to 6.34 m 2 /g). Our simulations suggest that silica binds tightly to the hydrophobic face of cellulose at room temperature, but HT significantly reduces the binding free energy of association with both hydrophobic and hydrophilic surfaces. Most significantly, ash removal leads to an increased calorific value, rising from approximately 16 MJ/kg to about 19 MJ/kg, along with improved thermal behavior. The improved integration combustion index parameter S indicates that the combustion properties improve with ash removal efficiency. The proposed atomic-level mechanism for the observed removal of inorganics during mild HT underscores the potential of such treatment in producing energy-dense wheat straw, a widely available agricultural residue.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Radiative Defects in Chloride-Activated CdSe Thin Films

Defect recombination limits wide-gap Se-based chalcogenide devices, yet how chloride activation reshapes radiative pathways remains unclear. Here we show that a 40 min CdCl 2 anneal converts evaporated CdSe from porous nanograins into dense micrometer-scale polycrystals and sharpens the optical band edge, reducing the Urbach energy from 85 to 17 meV at 300 K. Combining temperature- and fluence-dependent photoluminescence (PL), time-resolved PL, hyperspectral mapping, and hybrid-DFT, we resolve three emissive channels and identify their mechanisms. The near-edge band is excitonic at low temperature and evolves into free-carrier emission at elevated temperature. A sub-gap band at E g −0.45 eV requires above-gap carriers and thermally quenches with a 0.16 eV activation energy. A broad ∼1.05 eV infrared band is excited by above- and below-gap photons and retains microsecond lifetimes at room temperature; patial mapping links it to edge-rich microstructure. Calculations suggest selenium-vacancy and cadmium-vacancy−chlorine complexes, pointing to routes to suppress defect-related losses in wide-gap chalcogenide devices.

Abudulimu, Abasi [Univ. of Toledo, OH (United Stat↗
DOE OSTI2022

Thermal Hall effect in the Kitaev-Heisenberg system with spin-phonon coupling

Motivated by the giant phonon anomalies in α-RuCl3 reported by H. Li et al. [Nat. Commun. 12, 3513 (2021)], we investigate the thermal Hall effect in a Kitaev-Heisenberg system in the presence of the coupling between spins and phonons arising from chlorine atoms' vibration. We observe that the coupling modifies the relative stability between different magnetic states under a magnetic field, especially stabilizing a canted zigzag antiferromagnetic state. Remarkably, the spin-phonon interaction has distinct effects on the thermal Hall conductivity in different magnetically ordered states. For a canted zigzag state, which is relevant to α-RuCl3, the spin-phonon interaction enhances the magnon excitation gap induced by a magnetic field and suppresses the thermal Hall conductivity at low temperatures. For the Kitaev spin liquid state, we find that the spin-phonon interaction reduces the excitation gap of Majorana fermions and destabilizes the quantized thermal Hall effect. Our results demonstrate a crucial role of phonon degrees of freedom in the thermal Hall effect in Kitaev materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Unveiling the electronic structure and chemical bonding of the deprotonated cisplatin anion [(NH 3 )(NH 2 )PtCl 2 ] − via low-temperature photoelectron spectroscopy and theoretical calculations

The dehydrogenated cisplatin anion, [(NH 3 )(NH 2 )PtCl 2 ] − , was investigated via low-temperature photoelectron spectroscopy and theoretical calculations. Seven and four spectral peaks are respectively resolved at 193 and 266 nm, yielding rich electronic structure information for both the anion and neutral. From the threshold and maximum of the lowest electron binding energy band, the experimental adiabatic (ADE) and vertical detachment energies (VDE) are determined to be 3.3 ± 0.1 and 3.525 ± 0.025 eV, respectively. Theoretical calculations indicate the dominant isomer adopting a cis-geometry, in which the platinum center is coplanar with two chlorine and two nitrogen ligands. The calculated VDE of 3.54 eV based on this structure agrees well with the experimental value. Charge analyses reveal that the excess electron in the anion is primarily localized on the Pt and Cl atoms. A suite of theoretical analysis tools was employed to elucidate the bonding characteristics and interaction strength between Pt and its ligands.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Low-temperature dechlorination of polyvinyl chloride (PVC) for production of H 2 and carbon materials using liquid metal catalysts

Polyvinyl chloride (PVC) is ubiquitous in everyday life; however, it is not recycled because it degrades uncontrollably into toxic products above 250°C. Therefore, it is of interest to controllably dechlorinate PVC at mild temperatures to generate narrowly distributed carbon materials. We present a catalytic route to dechlorinate PVC (~90% reduction of Cl content) at mild temperature (200°C) to produce gas H 2 (with negligible coproduction of corrosive gas HCl) and carbon materials using Ga as a liquid metal (LM) catalyst. A LM was used to promote intimate contact between PVC and the catalytic sites. During dechlorination of PVC, Cl is sequestrated in the carbonaceous solid product. Later, chlorine is easily removed with an acetone wash at room temperature. The Ga LM catalyst is reusable, outperforms a traditional supported metal catalyst, and successfully converts (untreated) discarded PVC pipe.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Interhemispheric differences in polar stratospheric HNO3, H2O, ClO, and O3

Simultaneous global measurements of nitric acid (HNO3), water (H2O), chlorine monoxide (ClO), and ozone (O3) in the stratosphere have been obtained over complete annual cycles in both hemispheres by the Microwave Limb Sounder on the Upper Atmosphere Research Satellite. A sizeable decrease in gas-phase HNO3 was evident in the lower stratospheric vortex over Antarctica by early June 1992, followed by a significant reduction in gas-phase H2O after mid-July. By mid-August, near the time of peak ClO, abundances of gas-phase HNO3 and H2O were extremely low. The concentrations of HNO3 and H2O over Antarctica remained depressed into November, well after temperatures in the lower stratosphere had risen above the evaporation threshold for polar stratospheric clouds, implying that denitrification and dehydration had occurred. No large decreases in either gas-phase HNO3 or H2O were observed in the 1992-1993 Arctic winter vortex. Although ClO was enhanced over the Arctic as it was over the Antarctic, Arctic O3 depletion was substantially smaller than that over Antarctica. A major factor currently limiting the formation of an Arctic ozone 'hole' is the lack of denitrification in the northern polar vortex, but future cooling of the lower stratosphere could lead to more intense denitrification and consequently larger losses of Arctic ozone.

Santee, M. L.↗
NASA NTRS1961

Effect of Surface Preparation and Gas Flow on Nitrogen Atom Surface Recombination

The effects of surface preparation and gas flow on the recombination of nitrogen atoms at copper and platinum surfaces were determined. Atoms were generated by an electrodeless 2450-megacycle-per-second discharge, and their concentration was measured by gas-phase titration with nitric oxide. Test surfaces were either vacuum-evaporated films or spheres machined from bulk metal and cemented around small glass-bead thermistors. Heat released by recombination was measured as the difference in electrical energy required to maintain a given thermistor temperature with and without a catalytic surface exposed. Recombination coefficients measured at flow velocities of 1120, 1790, 2250, and 3460 centimeters per second and at pressures of 0.42 and 0.59 millimeter of mercury showed that flow conditions had no effect. The results were also independent of atom concentration. A rough indication of the temperature dependence was obtained; it was greater for copper than for platinum. Platinum films deposited on platinum or on glass had the same activity - about 3 percent of the atoms impinging recombined. With copper, however, the glass substrate greatly reduced the percent of atoms recombining over that of a bulk copper substrate where 4 percent of the impinging atoms recombined. This effect could be overcome by depositing a second film on top of the first. Bulk metal samples were subjected to various surface treatments including polishing, degreasing with a chlorinated hydrocarbon, washing with nitric acid, and rinsing with water. Polished, degreased platinum had low activity compared to an evaporated film, but nitric acid treatment made it equivalent. Polished, degreased copper was only slightly less active than a copper film; nitric acid etching decreased the activity still further, probably by preferentially exposing facets of low catalytic efficiency.

Prok, George M.↗
DOE OSTI2022

Trimethyloxonium-mediated methylation strategies for the rapid and simultaneous analysis of chlorinated phenols in various soils by electron impact gas chromatography–mass spectrometry

Abstract The efficient methylation of a panel of five industrial and environmentally-relevant chlorophenols (CPs) employing trimethyloxonium tetrafluoroborate (TMO) for their qualitative detection and identification by electron impact gas chromatography–mass spectrometry (EI-GC–MS) is presented. The protocol’s execution is simple and smoothly converts the phenols into their O-methylated counterparts conveniently at ambient temperature. The efficiency of two versions of the protocol was successfully tested in their ability to simultaneously derivatize five CPs (2-chlorophenol, 2,4-dichlorophenol, 2,4,6-trichlorophenol, pentachlorophenol and triclosan) in six distinct, separate soil matrices (Nebraska EPA standard soil, Virginia Type A soil, Ottawa sand, Baker sand, Silt and Georgia EPA standard soil) when present at low levels (~ 10 μgg −1 ). The first version involves the direct derivatization of the spiked soils with the methylating salt while the second one involves an initial soil extraction step of the CPs followed by methylation. The MDL values for each methylated CP were determined and lower values were found (4.1–13.2 ng . mL −1 ) for both sand matrices (Ottawa and Baker) as well as for the Georgia EPA standard soil, while larger values (8.2–21.8 ng . mL −1 ) were found for the Virginia Type soil, Nebraska EPA standard soil and Silt. The presented protocol offers a safer and more practical alternative to the universally employed diazomethane method and can be readily applicable to matrices other than soils. Furthermore, the protocols described herein may find applicability to the methylation of other analytes bearing acidic protons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗