Search NASA⌕ Search

SEARCH · Search NASA

Results for “low-temperature electrolysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

61 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Water-Fed, Photovoltaic-Driven Anion-Exchange Membrane Water Electrolysis for Solar Hydrogen Production

Direct coupled photovoltaic (PV)-electrolysis is a promising approach for low-cost hydrogen production, avoiding the need for separate electricity generation. Without solar concentration, the operating current densities of a PV-electrolyzer are small, and low capital costs are needed to reach hydrogen production cost targets (<$2/kg). Anion-exchange membrane (AEM) electrolyzers could be well-suited for this application due to their ability to use platinum group metal (PGM)-free catalysts and operate without supporting electrolytes, but a water-fed PV-AEM system has not yet been demonstrated. In this work, the performance of two AEM electrolyzer designs under pure-water, low-temperature, and diurnal-cycling conditions was evaluated. A simple PV-electrolyzer system design with direct electric coupling to a commercial 84 cm2 Si mini module and passive heating and water flow to the electrolyzer was used for on-sun testing in October 2025. The best-performing PV-AEM system achieved an average solar-to-hydrogen (STH) efficiency of 6.6% and a production rate of 15 mg/kWh/m2 of solar irradiance over 11 days. Minimal electrolyzer corrosion was observed, with no loss in efficiency over the diurnal cycles. While highlighting areas for improved electrolyzer and system design, this work is a proof of concept for distributed hydrogen production using inexpensive and abundant materials.

08 HYDROGEN↗
DOE OSTI2022

Assessing the Oxidative Stability of Anion Exchange Membranes in Oxygen Saturated Aqueous Alkaline Solutions

While anion exchange membrane water electrolyzers show promise as a source of green hydrogen using low-temperatures and non-platinum group metal catalysts, many concerns must be addressed. A primary challenge for the development of high-performance anion exchange membrane water electrolyzers is the fabrication of a stable membrane that will be able to survive long-term stability test while maintaining high anion conductivity, which is a necessity for a durable water electrolyzer. This method will present a standardized protocol that can be used by researchers to assess the quality of their AEM materials and be able to provide insight into how materials may be degrading and how to improve the quality of AEMs. Using Mohr or Volhard titration to measure ion-exchange capacity, EIS to determine the ionic conductivity, NMR and FTIR to understand the extent of membrane degradation over time, and mechanical analyzers to determine the strength of their AEMs, this standardized protocol will guide researchers to determining and improving upon the long-term durability and performance of their AEM materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Ionomer-free nanoporous iridium nanosheet electrodes with boosted performance and catalyst utilization for high-efficiency water electrolyzers

Increasing the catalyst utilization efficiency and simplifying electrode fabrication processes are crucial to accelerate development of low-cost proton exchange membrane electrolyzer cells (PEMECs). Here, we develop a facile route to fabricate ionomer-free iridium nanosheet integrated electrodes, in which nanoporous iridium nanosheets (IrNS) with abundant exposed edges and nanopores are deposited on thin titanium liquid/gas diffusion layers (TT-LGDLs) via a low-temperature chemical synthesis strategy. Further, benefiting from high catalytic activity, good electrode conductivity and excellent liquid/gas transport properties, such nanoporous IrNS electrodes with low catalyst loadings require low cell voltages of 1.65 V and 1.78 V at 3000 and 6000 mA/cm 2 , respectively. More impressively, a stable performance can be well maintained under extremely high current density tests of 5000 mA/cm 2 , demonstrating the potential of low-loading nanoporous IrNS electrodes in solid-electrolyte based electrochemical conversion cells that require high current density operation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Electrochemical chlor-iron process for iron production from iron oxide and salt water

The iron and steel industry accounts for ~8% of global greenhouse gas emissions. Electrochemical reduction of iron ore to metal for electric arc furnaces can enable sustainable steel production, but existing electrochemical processes require expensive capital or electrolytes. Here we report a low-temperature, electrochemical cell that consumes low-cost and abundant iron oxide and aqueous sodium chloride, while co-producing sodium hydroxide and chlorine. Industrially relevant current densities and Faradaic efficiencies for iron production were demonstrated, with 94% selectivity to iron metal at an applied current density of 200 mA cm –2 . Freestanding films of phase-pure iron were formed after 4h of continuous, stable electrolysis. The process can lead to levelized costs of iron that are competitive with iron produced in fossil-fuel-powered blast furnaces, and the co-produced sodium hydroxide can be used for CO 2 capture from the air or ocean, creating a net-negative-emission process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Revitalizing interface in protonic ceramic cells by acid etch

Protonic ceramic electrochemical cells hold the promise to be operated at intermediate temperatures below 600 °C. Although the high proton conductivity of the bulk electrolyte has been demonstrated, it cannot be fully utilized in electrochemical full cells due to unknown causes. A practical solution is thus urgently needed. Here we showed that it comes from poor contacts between the low-temperature processed oxygen electrode-electrolyte interface. We demonstrated that a simple acid treatment can effectively rejuvenate the high-temperature annealed electrolyte surface, resulting in reactive bonding between the oxygen electrode and the electrolyte and improved electrochemical performance and stability. This enables exceptional protonic ceramic fuel-cell performance down to 350 °C, with peak power densities of 1.6 W cm -2 at 600 °C, 650 mW cm -2 at 450 °C, and 300 mW cm -2 at 350 °C, as well as stable electrolysis operations at large current densities above 3.9 A cm -2 under 1.4 V applied voltage at 600 °C. Furthermore, our work highlights the critical role of interfacial engineering in ceramic electrochemical devices and offers new understanding and practices towards sustainable energy infrastructure.

08 HYDROGEN↗
DOE OSTI2022

Intermediate Temperature Solid Oxide Cell with a Barrier Layer Free Oxygen Electrode and Phase Inversion Derived Hydrogen Electrode

High-temperature solid oxide cells (SOCs) have fundamental advantages in efficiency and product rate over their low-temperature counterparts. However, the commercial development of SOCs is hindered by cost and reliability. To solve the issues, lowering the operating temperature of SOCs is deemed the best solution. Here we report on our effort toward intermediate temperature (IT) SOCs by developing a barrier layer free high-performance oxygen electrode and open structured hydrogen electrode. The results show that the new oxygen electrode provides reasonably good oxygen electrocatalytic activity at IT range for oxygen reduction and evolution reactions and the open structured hydrogen electrode provides low gas diffusion path for H 2 /H 2 O. However, at high electrolysis current density such as 1 A cm −2 and 650 °C, the present oxygen electrode delaminates after 200 h. The phase-inversion derived open structured hydrogen electrode helps gas diffusion but, in the meantime, reduces reactive sites. A proper balance of porosity and number of reactive sites is still needed for future hydrogen electrode development.

25 ENERGY STORAGE↗
DOE OSTI2024

Technoeconomic Analysis of Discrete and Unitized Reversible Fuel Cells for Energy Storage Applications

Reversible Fuel Cell (RFC) systems offer promising characteristics for stationary long duration energy storage applications. Two main configurations of RFC systems exist: discrete RFC systems and unitized RFC systems. While discrete RFC systems combine independent fuel cell and electrolyzer systems for energy storage, unitized RFC systems utilize a single electrochemical stack and might share balance of plant (BOP) components for both charging and discharging processes. While this configuration reduces upfront capital costs, challenges of unitized RFC designs include potential performance trade-offs due to dual-mode stack design and operational complexities across varying loads and operating conditions. Furthermore, these tradeoffs might be different for low-temperature PEM RFCs than for high-temperature reversible solid oxide cell systems. The goal of this project is to assess unitized RFC system potential in the context of long duration grid energy storage and HFTO's technical targets for different discrete fuel cell and electrolyzer technologies. This presentation presents preliminary review of state-of-the-art unitized RFC cells and assesses how they perform relative to HFTO's technical targets. It also presents literature-derived system configurations worth investigating. This review indicates that lab-scale unitized RFCs are making good progress towards meeting HFTO's technical targets.

HYDROGEN↗