SEARCH · Search NASA

Results for “low-temperature performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2026

Enhancing photoionization rate calculations in low-temperature plasmas using spectral methods

Photoionization plays a central role in the development of streamer discharges and other non-equilibrium plasma phenomena. It creates seed electrons, which are essential for positive streamer propagation, allowing the ionization front to move forward. Because of this, accurate modeling of photoionization is very important for predicting streamer behavior and plasma evolution. The photoionization process in air (N 2 – O 2 mixture) is often described by the Zheleznyak model (1982). This model is usually solved through Helmholtz-type equations that approximate the Zheleznyak photoionization model (Zheleznyak et al. 1982) as Partial Differential Equations (PDEs). Conventional numerical methods, such as the Finite Difference Method (FDM) or Finite Volume Method (FVM), are widely used to solve these equations. Although they are prevalent, the computational cost of these methods due to their need for matrix operations and iterative solver is demanding. To address this challenge, this work develops a spectral solver based on the Fast Fourier Transform (FFT) combined with Discrete Cosine Transform (DCT) and Discrete Sine Transform (DST) to calculate the photoionization rate efficiently in an axisymmetric cylindrical domain. This method naturally satisfies the boundary conditions used in the model and converts the PDE into algebraic ones in spectral space. Thus, avoids the need for iterative matrix solvers. When compared with FDM results, it is demonstrated that the new solver not only maintains accuracy, but also reduces the computational cost, showing a performance increase of approximately 100 compared to FDM over a wide range of problem sizes. The method is parallelized using Message Passing Interface (MPI) and has been integrated into a fluid plasma model for streamer simulation. Here, this FFT-based approach provides a fast and reliable alternative for calculating photoionization in fluid models, helping large-scale plasma simulations run faster and efficiently, and allows higher-resolution simulation without extra computational cost.

Axisymmetric system↗

DOE OSTI2025

Pyrrole‐Imine Macrocycle: Self‐Organizing Cross‐Reactive Anion Receptor and Sensor

Self-organizing macrocyclic receptor-sensors for phosphorus oxyanions, phosphates, and phosphonates comprising imine moieties were prepared by condensation of dipyrrolylmethane dicarbaldehyde with diethylene triamine. The incorporation of flexible ethylene moieties endows the macrocycle with unprecedented flexibility and ability to accommodate numerous phosphorus oxyanions from orthophosphate to large anions such as ATP or phosphonate glyphosate. The anion binding was elucidated by NMR titrations, low-temperature NMR, and NOESY NMR. The incorporation of dansyl fluorophore enables sensing of anions using the fluorescence signal, whereas the changes in fluorescence intensity, width of the fluorescence band, and position of the maxima are analyte-specific and useful in recognition and identification of eleven different P-oxyanions in water. The affinity (K assoc ) for Na + salts was H 2 PO 4 − ≈ Methylphosphonate > H 2 P 2 O 7 2− > Phenylphosphonate- > Glyphosate 2− > AMP 2− > ADP 2− > ATP 2− . Interestingly, phosphonates, including methylphosphonate and glyphosate anions, were also found to display a strong affinity (K assoc ∼10 6 M −1 ) while halides, nitrate, carbonates, or hydrogen sulfate did not show a significant affinity. The determined fluorescence spectral parameters were used to classify the 12 analytes (11 anions and water) using Linear Discriminant Analysis (LDA). Quantification was performed using LDA and Support Vector Machine (SVM), and the phosphonate concentrations in unknown samples were determined with an error of 3.5% or lower.

anions↗

DOE OSTI2026

Modulating charge transport via 2 MeV He + irradiation in VO 2

Vanadium dioxide (VO 2 ) is of interest for adaptive electronic applications such as neuromorphic neuristor devices and variable emissivity or tunable thermal control materials, thanks to its key property—a metal–insulator transition (MIT) at 68 °C that is accompanied by a dramatic change in electrical and optical properties. To improve performance in these roles, it is critical to develop approaches to engineer transport properties and the MIT behavior. While many documented techniques exist to modulate the MIT and film resistivities via lattice strain and chemical doping, less is known about the effects of ion irradiation on the intrinsic properties of VO 2 , despite the ability to control the spatial distribution of irradiation beams and the prevalence of high energy ion implantation in the semiconductor industry. The impact of irradiation of different acceleration energies on the responses of VO 2 is of specific interest, as charged particle energy generally impacts both the resulting defect profile and corresponding transport behavior. Here, we demonstrate that 2 MeV He ions at equivalent calculated displacements per atom, in two different types of films, can create remarkable changes to the nature of charge transport in VO 2 , especially in the low-temperature insulating phase. Simulation of resulting changes in electrical conductivity reveals that He ion irradiation offers a strategy to increase both oscillation frequency and the signal transmission. These results provide insights into the intentional design of defect populations to modulate transport for neuromorphic VO 2 devices.

Gurrola, Rebeca M. [Texas A & M Univ., College Sta↗

DOE OSTI2026

The detection of marine microseismic activity with the CUORE tonne-scale cryogenic experiment

Vibrations from experimental setups and the environment are a persistent source of noise for low-temperature calorimeters searching for rare events, including neutrinoless double beta ( 0νββ ) decay or dark matter interactions. Such noise can significantly limit experimental sensitivity to the physics case under investigation. Here, we report the detection of marine microseismic vibrations using mK-scale calorimeters. This study employs a multi-device analysis correlating data from CUORE, the leading experiment in the search for 0νββ decay with mK-scale calorimeters, and the Copernicus Earth Observation program, revealing the seasonal impact of Mediterranean Sea activity on CUORE’s energy thresholds, resolution, and sensitivity over four years. The detection of marine microseisms underscores the need to address faint environmental noise in ultra-sensitive experiments. Understanding how such noise couples to the detector and developing mitigation strategies is essential for next-generation experiments. We demonstrate one such strategy: a noise decorrelation algorithm implemented in CUORE using auxiliary sensors, which reduces vibrational noise and improves detector performance. Enhancing sensitivity to 0νββ decay and to rare events with low-energy signatures requires identifying unresolved noise sources, advancing noise reduction methods, and improving vibration suppression systems, all of which inform the design of next-generation rare event experiments.

experimental nuclear physics↗

DOE OSTI2025

In Situ Atomic Tracking on the Interfacial Etching and Reconfiguration of Cu-ReSe 2 Contact during Thermal Annealing

The Schottky barrier height can be greatly affected by the metal diffusion, reaction, and covalent bonding formation at the contact. Exploring novel methods and revealing the fundamental mechanisms for contact engineering are of vital importance for microelectronic devices. Here, in this study, the annealing induced interfacial reactions at Cu-ReSe 2 contact are dynamically revealed from the atomic scale. Accompanied by the diffusion of Se to Cu, ReSe 2 is gradually decomposed to a thin Re interlayer through a “chain-by-chain” manner. Theoretical calculations show that the Cu atoms can facilitate the chemical bond breaking of ReSe 2 , significantly lowering the Se diffusion energy barrier toward Cu. The formed Re/ReSe 2 heterostructure presents a metal-like band structure, which underscores the critical role of Cu in altering the interfacial chemistry and promoting carrier transport across the interface. Our results can provide vital insights into the contact properties of ReSe 2 and provide a possible method for fabricating high-performance ReSe 2 -based devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2026

Disentangling cation effects on ion mobility and structure in ionic liquid electrolytes

Ionic liquids (ILs) are low-temperature molten salts, where ion transport is primarily governed by ion–ion interactions. Yet, the impact of organic IL cations on critical electrolyte properties such as ion dissociation and overall transport behavior in lithium-salt-doped ILs remains poorly understood. Moreover, despite their critical role in designing IL-based electrolytes for energy storage applications, ion–ion interactions and ion-specific transport under an applied electrical potential are seldom quantified, largely due to the unique experimental and computational challenges involved. Herein, we compare transport properties obtained using 1 H, 7 Li, and 19 F pulsed-field gradient nuclear magnetic resonance (NMR) and electrophoretic NMR (eNMR) with those measured by electrochemical impedance spectroscopy. Non-equilibrium molecular dynamics (MD) simulations and eNMR confirm the presence of negatively charged [Li(TFSI) n ] (1−n) aggregates that migrate towards the positive electrode, resulting in negative lithium transference numbers. Equilibrium MD simulations reveal a vehicular Li ion transport mechanism facilitated by long-lived aggregates with Li + cations strongly bound to multiple TFSI − anions. Finally, we observe an inverse relationship between the apparent charge of the TFSI − anion in the neat IL, which is dictated by the IL cation, and Li + transport in the salt-doped systems. This highlights the opportunity to tune electrolyte performance by tailoring cation chemistry.

Li-ion batteries↗

DOE OSTI2025

Colossal Cryogenic Electro‐Optic Response Through Metastability in Strained BaTiO 3 Thin Films

The search for thin film electro-optic materials that can retain superior performance under cryogenic conditions has become critical for quantum computing. Barium titanate thin films show large linear electro-optic coefficients in the tetragonal phase at room temperature, which is severely degraded down to ≈200 pm V −1 in the rhombohedral phase at cryogenic temperatures. There is immense interest in manipulating these phase transformations and retaining superior electro-optic properties down to liquid helium temperature. Utilizing the thermodynamic theory of optical properties, a large low-temperature electro-optic response is designed by engineering the energetic competition between different ferroelectric phases, leading to a low-symmetry monoclinic phase with a massive electro-optic response. The existence of this phase is demonstrated in a strain-tuned BaTiO 3 thin film that exhibits a linear electro-optic coefficient of 2516 ± 100 pm V −1 at 5 K, which is an order of magnitude higher than the best reported performance thus far. Importantly, the electro-optic coefficient increases by 100 × during cooling, unlike the conventional films, where it degrades. Further, at the lowest temperature, significant higher order electro-optic responses also emerge. These results represent a new framework for designing materials with property enhancements by stabilizing highly tunable metastable phases with strain.

barium titanate↗

DOE OSTI2026

Low-Temperature Gold Deposition Improves CdTe Back Contacts

Improved back contacts can benefit CdTe photovoltaics (PV). In this work, Cd(Se,Te) PV absorbers are cooled during Au evaporation to thermally quench a chemical reaction occurring between gold and CdTe and the generation of a reaction product that lowers device efficiency. Reducing substrate temperature enhances PV power conversion efficiency via open-circuit voltage and fill factor increases. X-ray photoelectron spectroscopy (XPS) reveals that lower temperature also reduces chemical perturbations of the CdTe, potentially linking back contact formation to a CdTe degradation product that hinders PV performance. Comparing reaction enthalpy and substrate heating energy shows that back contact formation by sputtering elemental metals onto ZnTe may exhibit a degradation pathway analogous to that of CdTe/Au reported here. Degradation-diminishing contact formation processes are therefore of general interest for optoelectronic devices, and the reduced substrate temperature in this study is one example.

14 SOLAR ENERGY↗

DOE OSTI2025

Impact of gasoline composition on the effects of nitric oxide on autoignition and knock in a DISI engine

Modern spark-ignition engines use exhaust gas recirculation (EGR) to dilute the charge and suppress knock, enabling the use of higher compression ratios and/or more optimum combustion phasing for higher efficiency. The effectiveness of EGR is affected by the composition of the fuel and its chemical-kinetic interactions with combustion products. Among those, nitric oxide (NO) has been shown to strongly affect autoignition reactivity. However, the impact of fuel composition of the effect of NO on reactivity is not well-understood. Here, in this study, engine experiments were conducted to assess the impact of NO seeded to the intake on knock-limited operation of two gasoline fuels (high cycloalkane content, or HCA, and high olefin content, or HO). Results showed that compositionally-different fuels responded differently to NO. HCA, which was less knock-limited than HO for NO < 200 ppm, became more knock-limited for NO > 200 ppm. Moreover, it was found that differences in knock between fuels were caused by differences in autoignition chemistry and not in the sequential autoignition process of the end gas that occurs due to thermal stratification. Chemical kinetic simulations were performed to better understand the experimental results. For HCA, intermediate-temperature heat release had a greater impact on autoignition reactivity than low-temperature heat release, while the opposite was observed for HO. For both fuels, NO enhances the magnitude of low-temperature heat release via NO + HO 2 → NO 2 + OH. The effect of NO on reactivity was stronger for HCA because OH produced from NO helped to overcome the OH quenching effect of cyclopentane, a main species in HCA. In contrast, HO had relatively strong inherent low-temperature chemistry arising from iso-octane, which reduced the impact of NO on reactivity. For the range of NO mole fractions tested in this study, in-cylinder NO increased fuel’s knock propensity, especially for fuels with mild low-temperature chemistry.

Autoignition↗

DOE OSTI2026

Insights into Native Single-Atom Electrocatalyst Site Structures

Single-atom electrocatalysts consisting of metal atoms embedded in a carbon matrix are promising next-generation catalysts for green hydrogen production and utilization, CO2 reduction, low-temperature CO oxidation, ammonia production, plastic decomposition, and electrochemical energy storage. The origins of activity and stability for the single-atom sites are still debatable, however, because of constrained insights into their local structure resulting from idealized models and experiments derived from a large number of individual sites. Insights into structural variations around single atomic sites are therefore critical for the continued development of these next-generation catalysts. While electron microscopy commonly provides atomic-scale information about these materials, the beam sensitivity of individual sites makes structural determination by conventional low-voltage (60 keV) techniques challenging. Here, we introduce ultralow-voltage electron ptychography, performed at 30 keV, that enables determination of the lattice structure around individual metal sites in a well-defined single-atom electrocatalyst system while essentially eliminating knock-on structural modifications. Pairing these atomic-scale, site-specific measurements with computational methods will broaden our understanding of the activity and stability of these materials, which will accelerate the development of the next generation of catalysts.

Zachman, Michael [ORNL] (ORCID:0000000319101357)↗

DOE OSTI2025

Boundary scattering in topological Kondo insulator SmB 6

We have studied the effects of phonon-boundary scattering on the thermal transport of topological Kondo insulator SmB6. The studies have been performed using the 3ω method across a temperature range 3–300 K. Our results indicate that the thermal conductivity of micro-sized SmB 6 is of an order of magnitude smaller than that of a bulk single crystal. Using the Callaway model, we analyzed the low-temperature lattice thermal conductivity of the microcrystal and demonstrated that phonon scattering at the sample boundaries is a major contributor to the thermal resistance in this topological material. Furthermore, our study reveals that the temperature dependence of the lattice thermal conductivity exhibits a double-peak structure, suggesting strong phonon–phonon or phonon–defect interactions in this material, characteristic of resonant scattering. Furthermore, these findings will help in a better understanding of thermal transport in advanced materials and devices at the micro scale.

Physics - Condensed matter physics↗

DOE OSTI2025

Carrier Localization and Spontaneous Formation of Two-Dimensional Polarization Domain in Halide Perovskites

Halide perovskites are known for their rich phase diagram and superior performance in diverse optoelectronics applications. The latter property is often attributed to the long electron-hole recombination time, whose underlying physical mechanism has been a long-standing controversy. In this Letter, we investigate the transport and localization properties of electron and hole carriers in a prototypical halide perovskite (CsPbBr 3 ), through ab initio tight-binding nonadiabatic dynamics approach for large-scale (tens of nm size) supercell calculations, to simulate electron and ion dynamics on the same footing. Here, we found distinct structural, lattice polarization, and electron-phonon coupling properties at low (below 100 K) and high temperatures, consistent with experimental observations. In particular, at low temperature we find spontaneous formation of polar grain boundaries in the nonpolar bulk systems, which result in two-dimensional polarization patterns that serve to localize and separate electrons and holes. We reveal phonon-assisted variable-range hopping mostly responsible for low-temperature transport, and their characteristic frequency correlates with temperature-dependent phonon power spectrum and energy oscillation frequency in nonadiabatic dynamics. We answer the critical questions of long electron-hole recombination lifetime at low temperature and offer the correlation among polarization domains, electron-phonon couplings, and photocarrier dynamics.

Carrier generation & recombination↗

DOE OSTI2025

Range-separated thermal hybrid exchange-correlation density functional for accurate band-gap calculations of warm dense matter

Here, in this study, we present a range-separated thermal hybrid exchange-correlation (XC) functional, termed RS-KDT0, which provides highly accurate band-gap predictions at elevated temperature while reducing the computational cost relative to thermal global hybrid functionals. At zero temperature, RS-KDT0 recovers the widely used ground-state range-separated hybrid functional HSE06. To assess its performance across temperature regimes, we conducted static calculations of electronic pressure, band gaps, and band structures. RS-KDT0 exhibits the same level of accuracy as HSE06 in the low-temperature regime and demonstrates improved agreement with finite-temperature GW calculations at elevated temperatures when compared to other thermal XC functionals such as the generalized gradient approximation (GGA)-level KDT16 and the global hybrid KDT0.

density functional theory↗

DOE OSTI2026

An Acid-Free, Temperature-Based Cation Contamination Removal Strategy for PEM Water Electrolysis

It is widely understood that the durability and reliability of polymer electrolyte membrane (PEM) water electrolyzers are heavily dependent on feedwater purity, with cation contaminants that originate from incomplete water purification and balance of plant materials significantly harming electrolyzer performance. However, contamination remains a challenge and a common cause of failure at the stack level, indicating the need for strategies to recover the performance of contaminated cells. In this study, we investigate the effects of temperature on the uptake, electrochemical impacts, and removal of contaminant calcium and iron cations. Lower operating temperatures increase the sensitivity of the cell performance to contaminant cations, while also decreasing cation uptake and promoting contaminant removal. Computational charge transfer modelling shows that lower temperature increases the concentration of contaminant at the cathode and facilitates their removal from the cell. By testing single cells under scenarios designed to mimic stack temperature dynamics, we investigate low-temperature operation as an approach to stack-relevant contaminant recovery. Together, these results demonstrate that the low-temperature recovery approach is a promising approach for acid-free contamination recovery for PEM water electrolysis to promote stack reliability and durability.

08 HYDROGEN↗

DOE OSTI2026

Dual Purpose – Heating & Cooling – Thermal Battery for Flexible and Energy-Efficient Heat Pump Systems

The integration of heat pumps with thermal energy storage (HP-TES) systems is gaining attention as a viable solution for managing peak building demand driven by immense cooling and heating loads. With growing reliance on renewable energy sources, thermal energy storage offers an excellent opportunity to mitigate mismatches in thermal load between energy supply and demand. The use of phase-change material (PCM) TES is especially promising, as PCMs offer significant latent energy storage capacity with smaller temperature glides in smaller volumes compared to other TES technologies. However, challenges arise because current HP-TES architectures can load-shift only cooling or heating, not both, requiring two systems and thus doubling cost, weight, and footprint. Furthermore, current research efforts lack specific tools and techniques to advance integrated systems from concept design to end-user application, focusing on only discharge performance. To address these challenges, this research proposes a dual-mode (heating and cooling) integrated HP-TES system that uses room-temperature PCM-TES as a high-temperature heat source in heating mode and a low-temperature heat sink in cooling mode, thereby reducing temperature lifts and compressor power. Design criteria for PCM-TES heat exchangers were developed, balancing thermal-hydraulic performance with practical constraints such as available building space and weight requirements along with PCM selection considerations such as shipping conditions, moisture exposure, and number of available cycles. A detailed transient model for HP-TES systems was developed to enable rapid annual performance assessments in any US climate zone.

42 ENGINEERING↗

DOE OSTI2026

HydroGEN Consortium: Advancements in Hydrogen Production

HydroGEN Energy Materials Network (EMN) is an U.S. Department of Energy (DOE) EERE Hydrogen and Fuel Cell Technologies Office (HFTO)-funded consortium that aims to accelerate the discovery and development of advanced water splitting materials (AWSM) for clean, low-cost hydrogen production. Materials innovations are key to enhancing performance, durability, and cost of hydrogen generation technologies. HydroGEN is focused on low technology readiness level AWS technologies, including low- (alkaline exchanged membrane electrolysis) and high-temperature electrolysis (proton-conducting solid oxide electrolysis), photoelectrochecmical (PEC) and thermochemical (TCH) water splitting. The AWS technologies in this consortium study proton conduction in solid oxide electrolysis and hydroxide conduction in polymer electrolysis, and proton transport in photoelectrochemical water splitting. This presentation will provide an overview of the HydroGEN EMN and technical highlights of a few lab-led and DOE-awarded "seedling" R&D projects. HydroGEN continues to grow its community of industry, university, and national laboratories, forming a national innovation ecosystem focused on renewable hydrogen production.

08 HYDROGEN↗

DOE OSTI2026

HydroGEN Consortium

08 HYDROGEN↗

DOE OSTI2026

Design and Validation of a Cryogenic Dilatometer

This project focuses on the design and development of a cryogenic dilatometer capable of measuring the thermal expansion of materials at extremely low temperatures. Understanding how materials change dimension with temperature is critical for applications involving cryogenic environments, particularly laminated systems housing superconducting magnets, where small dimensional changes can significantly affect performance and reliability. To address this, a dilatometer system was designed to operate within a liquid nitrogen environment while accurately measuring displacements caused by thermal contraction. The purpose of this device is to determine the coefficient of thermal expansion (CTE) of a material. The design process involved defining functional requirements, developing mechanical and thermal concepts for the measurement apparatus, selecting appropriate materials compatible with cryogenic temperatures, and integrating sensors capable of detecting small dimensional changes. The resulting system aims to provide a practical and repeatable method for evaluating material thermal expansion at cryogenic temperatures, supporting research into composite use in superconducting applications that require accurate characterization of material behavior in low-temperature environments.

Schmitt, Nicholas [Northern Illinois U.]↗