Search NASA⌕ Search

SEARCH · Search NASA

Results for “microstructure development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Microstructure, Texture, and Strength Development during High-Pressure Torsion of CrMnFeCoNi High-Entropy Alloy

The equiatomic face-centered cubic high-entropy alloy CrMnFeCoNi was severely deformed at room and liquid nitrogen temperature by high-pressure torsion up to shear strains of about 170. Its microstructure was analyzed by X-ray line profile analysis and transmission electron microscopy and its texture by X-ray microdiffraction. Microhardness measurements, after severe plastic deformation, were done at room temperature. It is shown that at a shear strain of about 20, a steady state grain size of 24 nm, and a dislocation density of the order of 1016 m−2 is reached. The dislocations are mainly screw-type with low dipole character. Mechanical twinning at room temperature is replaced by a martensitic phase transformation at 77 K. The texture developed at room temperature is typical for sheared face-centered cubic nanocrystalline metals, but it is extremely weak and becomes almost random after high-pressure torsion at 77 K. The strength of the nanocrystalline material produced by high-pressure torsion at 77 K is lower than that produced at room temperature. The results are discussed in terms of different mechanisms of deformation, including dislocation generation and propagation, twinning, grain boundary sliding, and phase transformation.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Graded microstructure and mechanical properties of spark plasma sintered Fe-Cr alloys

Developing graded microstructure and mechanical properties is critical for accelerating the design and optimization of structural materials for a wide range of applications. Here, in this study, Fe-Cr alloys were fabricated by spark plasma sintering (SPS) technique. The microstructure, microhardness, and tensile properties of the as-fabricated and thermally annealed variants were investigated. Graded grain structures were created in the as-fabricated cylinders along both axial and radial directions. Grain size was gradually reduced from the sample periphery to the center. Microhardness measurements reveal a gradual decrease of hardness towards the periphery of the samples. The as-fabricated Fe-Cr alloys show a desired combination of tensile strength and elongation, primarily due to the formation of a high density of oxides, voids, dislocations, and grain boundaries. After in-situ thermal annealing at 600 °C under 60 MPa for 2 h using SPS, the Fe-Cr alloys underwent minimal grain growth, and the graded grain structures were retained. The hardness was more uniformly distributed in the annealed variants, and the tensile strength was reduced with an increase in the total elongation, which is attributed to the dissolution of nano-sized oxide particles and the relief of the residual stress. This study demonstrates that SPS coupled with subsequent heat treatment can tailor the graded microstructure and control the mechanical properties of Fe-Cr alloys, showing potential applications in other alloy systems.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Which way does the dendrite grow? Competition among epitaxy, preferred growth direction, and thermal gradients in powder bed fusion additive manufacturing

The as-processed microstructure of metal alloy parts manufactured through laser powder bed fusion (LPBF) is heavily derived from the cellular dendritic solidification. The growth direction of dendrites within the melt pool is determined through competition among epitaxial growth, preferred growth directions, and maximum thermal gradients. However, the dominant factor and the specific role of each in developing melt pool microstructures remain unknown. Here, in this study, we performed single laser track scans on an SS316L single crystal substrate and combined experimental characterization of microstructure and crystal orientations with Computational Fluid Dynamics simulations of thermal gradients to evaluate the role of each factor in determining dendritic growth direction and evolution. Our results reveal that epitaxial growth dominates microstructure development by preferentially growing along a single 〈100〉 variant of the single crystal substrate adjacent to the melt pool boundary. Under LPBF’s highly curved and rapidly evolving thermal field, this preferential dendrite variant selection and its continued growth from the melt pool boundary to the centerline are governed by the local temperature gradient magnitude at the solid-liquid interface, rather than by the instantaneous maximum temperature gradient direction alone. Using these findings, we successfully predict changes in the dendrite growth direction with changing laser scan direction on a single crystal substrate, and show that the geometric melt pool centerline can deviate from the microstructural centerline because asymmetric local temperature gradient magnitudes transiently limit growth, resulting in different dendrite travel distances on each side of the melt pool.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural Engineering and Accelerated Test Method Development to Achieve Low Cost, High Performance Solutions for Hydrogen Storage and Delivery

This project made advancements in developing lower cost steel alloys with novel microstructural design for use in hydrogen refueling infrastructure such as storage, compressors, and dispensing components, and utilizing accelerated test methods to efficiently evaluate variations in alloy and microstructure design. The project specifically sought to design alloys with lower nickel contents to reduce alloy cost, which was accomplished through substituting manganese for nickel along with other alloy additions to control deformation characteristics known to be important for hydrogen embrittlement resistance. Through Mn substitutions for nickel, austenitic and duplex austenite-ferrite steels were successfully developed with lower cost than currently available commercial stainless steel products that are employed for hydrogen refueling infrastructure. The steels were processed to achieve comparable strength and toughness in hydrogen environments as the commercially available steels containing high Ni contents. To evaluate mechanical performance in hydrogen, a testing methodology was employed to compare ubiquitous laboratory testing using electrochemical hydrogen charging in a liquid electrolyte to less accessible high pressure gaseous testing. While the application of these steels is in high pressure gaseous environments, the electrochemical hydrogen charging tests produced comparable results. Additionally, the Los Alamos Neutron Scatting Center enabled characterization of deformation mechanisms of the steel alloys in the presence of hydrogen, which has been associated with steel alloy characteristics associated with hydrogen embrittlement. Finally, a fracture mechanics based test bed model was developed to predict the influence of hydrogen gas pressure and fatigue conditions on fatigue lifetimes of pressure vessel steels. Together, these developments can be employed to enable lower cost hydrogen fueling infrastructure and more reliable prediction of steel alloy components in hydrogen service conditions. In particular, the newly alloys have the potential to replace stainless steels, having demonstrated comparable performance at substantially reduced cost.

08 HYDROGEN↗
DOE OSTI2022

Micromechanical Fields Associated with Irregular Deformation Twins in Magnesium

Understanding and controlling the development of deformation twins is paramount for engineering strong and stable hexagonal close-packed (HCP) Mg alloys. Actual twins are often irregular in boundary morphology and twin crystallography, deviating from the classical picture commonly used in theory and simulation. In this work, the elastic strains and stresses around irregular twins are examined both experimentally and computationally to gain insight into how twins develop and the microstructural features that influence their development. A nanoprecession electron diffraction (N-PED) technique is used to measure the elastic strains within and around a $\left\{ {10\overline{1}2} \right\}$ tensile twin in AZ31B Mg alloy with nm scale resolution. A full-field elasto-viscoplastic fast Fourier transform (EVP-FFT) crystal plasticity model of the same sub-grain and irregular twin structure is employed to understand and interpret the measured elastic strain fields. The calculations predict spatially resolved elastic strain fields in good agreement with the measurement, as well as all the stress components and the dislocation density fields generated by the twin, which are not easily obtainable from the experiment. The model calculations find that neighboring twins, several twin thicknesses apart, have little influence on the twin-tip micromechanical fields. Furthermore, this work reveals that irregularity in the twin-tip shape has a negligible effect on the development of the elastic strains around and inside the twin. Importantly, the major contributor to these micromechanical fields is the alignment of the twinning shear direction with the twin boundary.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Identify the influence of microstructure on mesoscale creep and fatigue damage

This report describes the development of a microstructural model that can quantify the uncertainty in the observed rupture life of Grade 91 steel. The model is microstructural, meaning it relates microstructural characteristics of the material to the resulting material response. As such, one of the uses of this model is to identify the key microstructural parameters controlling the development of damage in Grade 91 operating at elevated temperatures. The report describes two veins of work: improvements to the crystal plasticity model required to run the uncertainty quantification analysis and the results of that UQ analysis. For creep, the model identifies the grain boundary diffusivity as the critical parameter controlling the rupture life of the material. The report demonstrates that a reasonable microstructural distribution of grain boundary diffusivity can account for the observed macroscale variation in rupture life at fixed temperature and load.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Prediction of the influence of strain magnitude and strain path on the resulting microstructure and post-forming mechanical behavior of RA containing high formability steels

In third generation advanced high strength steels (AHSS) there is considerable potential to alter the transformation characteristics through variation of process parameters and through changes in chemical composition. This proposal aims to utilize this known phenomenon to develop microstructure-based transformation models to predict austenite stability as a function of chemical composition, strain level, deformation mode. The ultimate intent is to predict microstructure and performance during room temperature forming to produce automotive structural components with superior strength and failure resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Additive Manufacture of Multi-Functional, Large-Scale Components

The poster summarizes the main results for a LDRD focused on developing a arc-based additive manufacturing (AM) system capable of fabricating large components with a composition gradient otherwise known as functionally graded materials (FGMs). FGMs are capable of addressing local extreme conditions in an optimal and cost-effective manner. The AM system (referred to as multi-Wire Arc Additive Manufacturing or m-WAAM) consisted of modifying a standard automated gas tungsten arc welding system to deliver multiple welding wires to the weld pool at controlled rates to deposit desired alloy compositions at critical locations. Numerous shapes and composition gradients were fabricated with the system and the effect of various deposition parameters on the nature of the composition profile were evaluated. Additionally, heat treatment of the FGM was performed to develop graded microstructures which should enhance dynamic impact performance of inexpensive steels. The project highlights the potential of m-WAAM to efficiently fabricate FGMs. However, this project only explored the science behind the technique and additional development work will be required to develop a fully-functional system that can build more complex components.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Interface velocity dependent solute trapping and phase selection during rapid solidification of laser melted hypo-eutectic Al-11at.%Cu alloy

Microstructure formation of a hypo-eutectic Al-11Cu (atom percent) alloy during solidification after laser melting has been studied by transmission electron microscopy (TEM). The evolution of the solid-liquid-interface velocity, V SL , during the solidification process has been determined from direct observation by in-situ TEM. This enabled correlating V SL with development of four distinct microstructure zones. Crystal growth mode transitions from planar to cellular, cellular to dendritic, dendritic to cellular, and cellular to planar, have been observed for the accelerating solid-liquid-interface. The transition from coupled two-phase growth to the single-phase growth occurred for V SL = V a = (0.80±0.05) m/s, where V a is the velocity of absolute stability, at the onset of banded morphology grain formation. The in-situ and post-mortem TEM uniquely permitted determination of the non-equilibrium solidus for the rapidly solidifying Al-11Cu alloy. Experimental evidence for solute clustering and chemical ordering tendencies at length scales on the order of ≤ 5nm has been detected in the single-phase regions of the banded grains. The structural features of the single-phase bands have been interpreted as signatures of ‘frozen in’ configurations present in the liquid boundary layer adjacent to the growing crystal, which has a width of about 3nm. Finally, the nano-scale spatiotemporal resolution experimental TEM studies performed here provided quantitative metrics, e.g. the solidification interface velocity dependent solute concentration of the α-Al phase and the near-atomic scale structure in the single-phase bands, that are uniquely suitable for comparison with theory and model predictions for solidification microstructure development in multicomponent alloys after laser melting.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructural Evolution of Tantalum During Deformation and Subsequent Annealing

Microstructure-aware models are necessary to predict the behavior of material based on process knowledge or to extrapolate mechanical properties of materials to environmental conditions which are not easily reproduced in the laboratory, e.g., nuclear reactor environments. Elemental Ta provides a relatively simple BCC system in which to develop a microstructural understanding of deformation processes which can then be applied to more complicated BCC alloys. In situ neutron diffraction during compressive deformation and subsequent heat treatment have been used to monitor the evolution of microstructural features in Ta throughout simulated processing steps. Crystallographic texture and dislocation density are determined as a function of first plastic strain, then temperature. Lattice strains are determined and attributed to stresses at macroscopic, grain and dislocation length scales. The increase of the dislocation density through deformation and subsequent recovery during heat treatment is monitored through the changing diffraction line profile. Also, randomization of the texture is used as a signature of recrystallization. The recovery of dislocations through annihilation is not observed to depend on the initial dislocation density in the range studied here. In contrast, recrystallization is observed to depend strongly on the initially dislocation density.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Developing Stable Critical Materials and Microstructure for High-Flux and Efficient Hydrogen Production through Reversible Solid Oxide Cells

Reversible Solid Oxide Cells (RSOCs), which operate as either Solid Oxide Fuel Cells (SOFCs) or Solid Oxide Electrolytic Cells (SOECs), hold great promise for clean, high-efficiency energy conversion and hydrogen production. However, their commercial potential is hindered by stability issues arising from temperature-induced materials degradation. While substantial progress has been made in developing durable, reduced-temperature SOFCs - bringing them closer to commercial deployment, SOECs still exhibit substantially higher degradation rates at both the cell and stack levels under practical operating conditions.

08 HYDROGEN↗
DOE OSTI2020

Database development and exploration of process–microstructure relationships using variational autoencoders

The paper demonstrates graphical representation of a large database containing process–microstructure relationships using an unsupervised machine learning algorithm. Correlating microstructural features to processing is an essential first step to answer the difficult problem of process sequence design. Here, a large database of 346,200 orientation distribution functions resulting from a variety of process sequences is constructed, where each sequence comprises up to four stages of tension, compression and rolling along different directions in various permutations. This open-source database is constructed for collaborative development of process design algorithms. The paper demonstrates a novel application of the large database: graphical representation of texture–process relationships. A variational autoencoder is used to reduce the entire database to a two dimensional latent space where variations in processes and properties can be visualized. Using proximity analysis in this latent space, we can quickly unearth multiple process solutions to the problem of texture or property design.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Using Artificial Microstructures to Understand Microstructure Property Relationship-Toughening Mechanisms in Metallic Glass (Final Report)

Metallic glasses are a new class of structural materials which exhibit exciting mechanical properties including high strength and elasticity. In terms of fracture toughness, the material class of metallic glasses spans a wide range; Some metallic glasses are extremely brittle and exhibit near ideal brittle behavior whereas others can be exceptional tough with values comparable to the toughest metals out there. Such large range of observed fracture toughness within the material class of metallic glasses is surprising as they have seemingly a very similar atomic structure. Therefore, we developed “artificial microstructures” which allows to decouple the various contribution of sample geometry, imperfection and structure. Specifically, we decouple variations in the alloys’ chemical composition and the atomic structure and quantified the resulting fracture toughness. Atomic structure of a metallic glass can be modified by the fictive temperature. The fictive temperature of a glass is the temperature at which the liquid metallic glass falls out of equilibrium upon colling and forms a glass. Upon further cooling the structure is maintained only thermal oscillations decrease due to a lower absolute temperature. We found that the effect of fictive temperature (same chemistry, different structural stages of the glass) is comparable to the variations of fracture toughness when the chemistry is varied. Hence, it appears that the subtle differences in the glass structure are responsible for the large range of fracture toughness’s observed. Our results reveal that fracture toughness within the material class of metallic glasses varies significantly and we found some example alloys with exceptional high resistance to fracture and others that are almost ideally brittle. Significant influences on the fracture toughness have the structure of the glass, its chemistry, and some imperfections in the structure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Heterogeneous microstructure of yttrium hydride and its relation to mechanical properties

Here, the goal of this study is to investigate the properties of yttrium hydride materials in relation to the microstructure, especially its homogeneity. High-throughput nanoindentation mapping was used to evaluate hardness distribution. Raman spectral imaging demonstrated its sensitivity to the presence of YH2 and impurities. Raman peak position maps were correlated with residual stress in the specimens. Electron backscatter diffraction mapping provided phase distributions with correlation to high-energy X-ray diffraction analysis. The experimental mapping data were combined and analyzed using unsupervised machine learning cluster procedures. The machine learning analysis revealed that yttrium hydride specimens contained a major δ-YH2 – x phase component and minor α-Y and δ-YH2 – x components with significant residual stress. The minor phase fraction decreased with increasing nominal H/Y ratio, which affected the nanoindentation and Vickers hardness. The multimodal mapping procedures described herein affect developing important microstructure–property relationships, as well as correlations in heterogeneity and mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2022

On the high-temperature stability of the Al 8 Cu 3 Ce intermetallic in an additively manufactured Al-Cu-Ce-Zr alloy

High-temperature resistant eutectic Al alloys are crucial materials for lightweight and energy efficient design in the automotive and aviation industries. Additive manufacturing offers a pathway to refine eutectic microstructures and develop novel alloys with superior high-temperature strength. High-volume fraction intermetallic Al-Cu-Ce alloys have been developed to deliver high-temperature strength in combination with reduced hot-tearing susceptibility. Zr is added to provide additional strengthening via nanoscale Al 3 Zr precipitation, and to stabilize and avoid coarsening of the Al 8 Cu 3 Ce phase. However, the detailed interaction between Zr and Al 8 Cu 3 Ce remains unexplored. In this work, we show with synchrotron X-ray diffraction that laser powder bed fusion fabricated Al-Cu-Ce and Al-Cu-Ce-Zr alloys contain predominantly the Al 8 Cu 3 Ce intermetallic in the as-fabricated condition. Heat treatment of the Al-Cu-Ce alloy results in the Al 8 Cu 3 Ce → Al 8 Cu 4 Ce phase transformation. In the Al-Cu-Ce-Zr alloy, minor fractions of (Al,Cu,Si) 4 Ce and Al 2 Cu-θ are found in the as-fabricated condition, while Al 8 Cu 3 Ce remains stable during heat treatment. Atom probe microscopy quantifies intermetallic stoichiometries and reveals how Zr is enriched at the Al-matrix/Al 8 Cu 3 Ce interface acting as a diffusion barrier against solute exchange. Calibrated thermodynamic modeling underpins this as a kinetic effect. Here, a qualitative microstructural model summarizes, how Zr stabilizes Al 8 Cu 3 Ce against phase transformations and coarsening.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Parameter development and characterization of laser powder directed energy deposition of Nb – Alloy C103 for thin wall geometries

This work focuses on the parameter development and microstructural characterization of Nb-based alloy C103 for thin wall structures produced via laser powder – directed energy deposition (LP – DED). Laser power and scanning speeds were varied as part of a design of experiments to identify adequate print parameters. Combinations were evaluated for relative density, porosity, and geometrical accuracy. A combination of a laser power of 1420 W and scanning speed of 14 mm/s resulted in a relative density >99%, exhibited a consistent weld bead profile and was used for further microstructural evaluation. A mix of optical and scanning electron microscopy (SEM) revealed small, slightly elongated grains along the edges and large epitaxial grains in the central region along the Build – Transverse view. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analysis revealed Hf rich columnar cells in the center that transition into an evenly spaced cellular structure towards the edges of the built sample. Electron backscatter diffraction (EBSD) scans show a sharp [001] texture when looking at the cross section of the sample along the build direction. The Build – Scan view revealed a zig – zag pattern that follows the back – and – forth deposition strategy that was used. Finally, microhardness measurements were taken in the as – built (AB) and stress relieved (SR) conditions to baseline preliminary mechanical properties. The AB condition exhibited a large amount of scatter in the data and averages up to 11% larger than the SR condition. The reduction in scatter upon applying the SR cycle are indicative of a large concertation of dislocations present in the AB condition.

36 MATERIALS SCIENCE↗