Multi-Bandwidth Frequency Selective Surfaces for Near Infrared Filtering: Design and Optimization
Frequency selective surfaces are widely used in the microwave and millimeter wave regions of the spectrum for filtering signals.
frequency↗
SEARCH · Search NASA
Results for “microwave filters”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Superconducting Nbti and Pb(cu) Bandpass Filters
Superconducting Nb0.45Ti0.55 and Pb electroplated on Cu bandpass microwave filtes were constructed to investigate their low loss properties at 4.7 K. An interdigital stripline filter configuration was selected as the optimum structure for future applications. The filter was designed to operate at 8.45 GHz with an equal ripple bandwidth of 0.15 GHz. The insertion loss and the noise temperature contribution were measured at 4.7 K. In addition, the insertion loss was studied as a function of out of band power (up to 1 watt) and temperature (4.7 K up to T(c)). Results of an oxygen free high conductivity Cu filter are included for comparison.
Bautista, J. J.↗
High Power Intermodulation Measurements up to 30 W of High Temperature Superconducting Filters
We have demonstrated a high power intermodulation measurement set-up capable of delivering 30 W in each of two fundamental tones. For closely spaced frequencies (less than 35 MHz), the dynamic range of the measurement is limited by the nonlinear performance of the mixer in the front end of the HP71210C spectrum analyzer. A tunable TE(sub 011) mode copper cavity was fabricated in which one of the endwalls could be adjusted shifting its resonant frequency between 5.7 and 6.6 GHz. Since the Q-value of this cavity is high, greater than 10(exp 4), and its bandwidth is small, less than 1 MHz, it can be used to attenuate the two fundamental tones relative to one of the harmonic tones, which greatly enhances the dynamic range of the measurement. This set-up can be used to measure the two-tone intermodulation distortion of any passive microwave device, e.g. a HTS filter, a connector, a cable, etc., over a frequency range of 5.9 to 6.4 GHz and a power range of 0.1 to 30 W. The third order intercept (TOI) of a prototype HTS filter measured at powers up to 30 W was +81.3 dBm.
Wilker, Charles↗
Atomic Clock Based on Opto-Electronic Oscillator
A proposed highly accurate clock or oscillator would be based on the concept of an opto-electronic oscillator (OEO) stabilized to an atomic transition. Opto-electronic oscillators, which have been described in a number of prior NASA Tech Briefs articles, generate signals at frequencies in the gigahertz range characterized by high spectral purity but not by longterm stability or accuracy. On the other hand, the signals generated by previously developed atomic clocks are characterized by long-term stability and accuracy but not by spectral purity. The proposed atomic clock would provide high spectral purity plus long-term stability and accuracy a combination of characteristics needed to realize advanced developments in communications and navigation. In addition, it should be possible to miniaturize the proposed atomic clock. When a laser beam is modulated by a microwave signal and applied to a photodetector, the electrical output of the photodetector includes a component at the microwave frequency. In atomic clocks of a type known as Raman clocks or coherent-population-trapping (CPT) clocks, microwave outputs are obtained from laser beams modulated, in each case, to create two sidebands that differ in frequency by the amount of a hyperfine transition in the ground state of atoms of an element in vapor form in a cell. The combination of these sidebands produces a transparency in the population of a higher electronic level that can be reached from either of the two ground-state hyperfine levels by absorption of a photon. The beam is transmitted through the vapor to a photodetector. The components of light scattered or transmitted by the atoms in the two hyperfine levels mix in the photodetector and thereby give rise to a signal at the hyperfine- transition frequency. The proposed atomic clock would include an OEO and a rubidium- or cesium- vapor cell operating in the CPT/Raman regime (see figure). In the OEO portion of this atomic clock, as in a typical prior OEO, a laser beam would pass through an electro-optical modulator, the modulated beam would be fed into a fiber-optic delay line, and the delayed beam would be fed to a photodetector. The electrical output of the photodetector would be detected, amplified, filtered, and fed back to the microwave input port of the modulator. The laser would be chosen to have the same wavelength as that of the pertinent ground-state/higher-state transition of the atoms in the vapor. The modulator/ filter combination would be designed to operate at the microwave frequency of the hyperfine transition. Part of the laser beam would be tapped from the fiberoptic loop of the OEO and introduced into the vapor cell. After passing through the cell, this portion of the beam would be detected differentially with a tapped portion of the fiber-optically-delayed beam. The electrical output of the photodetector would be amplified and filtered in a loop that would control a DC bias applied to the modulator. In this manner, the long-term stability and accuracy of the atomic transition would be transferred to the OEO.
Maleki, Lute↗
Characterization of quasi-optical filters with picosecond transient radiation
The broadband microwave transmission properties of quasi-optical components are characterized with optoelectronically generated, picosecond transient radiation. The polarization sensitivity of a lithographically fabricated wire grating, from 15-140 GHz, is presented. The complex transmission functions of two different uniform arrays of cross dipoles are measured and compared with theoretical predictions.
Arjavalingam, G.↗
Y-Ba-Cu-O superconducting/GaAs semiconducting hybrid circuits for microwave applications
A two pole superconducting bandpass filter was combined with a packaged GaAs low noise amplifier, and a superconducting X-band oscillator was designed, fabricated, and tested. Both circuits were compared to normal metal circuits at 77K. The results of these experiments, technical issues, and potential applications are presented.
Bhasin, K. B.↗
High temperature superconducting thin film microwave circuits: Fabrication, characterization, and applications
Epitaxial YBa2Cu3O7 films were grown on several microwave substrates. Surface resistance and penetration depth measurements were performed to determine the quality of these films. Here the properties of these films on key microwave substrates are described. The fabrication and characterization of a microwave ring resonator circuit to determine transmission line losses are presented. Lower losses than those observed in gold resonator circuits were observed at temperatures lower than critical transition temperature. Based on these results, potential applications of microwave superconducting circuits such as filters, resonators, oscillators, phase shifters, and antenna elements in space communication systems are identified.
Bhasin, K. B.↗
High temperature superconducting thin film microwave circuits - Fabrication, characterization, and applications
Epitaxial YBa2Cu3O7 films were grown on several microwave substrates. Surface resistance and penetration depth measurements were performed to determine the quality of these films. Here, the properties of these films on key microwave substrates are described. The fabrication and characterization of a microwave ring resonator circuit to determine transmission line losses are presented. Lower losses than those observed in gold resonator circuits were observed at temperatures lower than critical transition temperature. Based on these results, potential applications of microwave superconducting circuits such as filters, resonators, oscillators, phase shifters, and antenna elements in space communication systems are identified.
Bhasin, K. B.↗
High-Temperature-Superconductor Films In Microwave Circuits
Report discusses recent developments in continuing research on fabrication and characterization of thin films of high-temperature superconducting material and incorporation of such films into microwave circuits. Research motivated by prospect of exploiting superconductivity to reduce electrical losses and thereby enhancing performance of such critical microwave components as ring resonators, filters, transmission lines, phase shifters, and feed lines in phased-array antennas.
Bhasin, K. B.↗
Effects of Hydrogen on Tantalum Nitride Resistors
This document is a presentation about the investigation of drift reported in static frequency output from the analog circuit of a Multichannel Microwave Integrated circuit hybrid microelectronic filter module for space flight application. Electron Dispersion X-Ray Detector )EDAX) Analysis of the 35k ohm thin film Tantalum Nitride Chip resistors identified Palladium in the film. A catalytic reaction of Palladium and hydrogen produces mono atomic hydrogen. When the filter module cavities were filled with a 4 % hydrogen 96 % Nitrogen gas mixture at 25C and monitored the electrical performance for 24 hours. Some channels drifted in a similar pattern as the channel being investigated. Palladium was found on the resistors. The corrective actions taken are reviewed, which resulted in a stable circuit.
Weiler, James↗
Life Cycle Testing of Ba(x)Sr(1-x)TiO3 Ferroelectric Thin Films in a Tunable Microwave Device
Thin film ferroelectrics are being studied as candidates for novel tunable microwave components such as tunable filters, tunable oscillators, and phase shifters for applications in phased array antennas. Much work has been done optimizing the ferroelectric material and in producing proof-of-concepts of these components. However, little attention has been given to their reliability. In this study we present our results on the reliability of high quality K-band phase shifters made of Ba(sub x)Sr(sub 1-x)TiO3 (BSTO) ferroelectric thin films (0.5 to 0.75 micrometers thick) on MgO and LAO. The phase shift and insertion loss were measured at 300 K over 104 operation cycles within a 0 to 400 V dc bias range (0 to 40 V/micrometer) at 15, 18, and 22 GHz. Results for these phase shifters indicate that in general there were no appreciable changes in phase shift after 4x10(exp 4) cycles, suggesting that these phase shifters are robust enough to sustain optimal performance under the operating mode typical of fast tracking phased arrays.
Miranda, Felix A.↗
Photonic frequency synthesis and control with Whispering Gellery Mode microresonators
We report here on experimental and theorectical studies of electro-optical tunability of WGM's in high-Q monolithic lithium niobate resonators and applicability of such resonators for light modulation and filtering. Properties of an optoelectronic microwave oscillator (EOE) based on an WGM LiNbO3 resonator are discussed.
Whispering Gallery Modes↗
Assimilation of SMAP and ASCAT Soil Moisture Retrievals into the JULES Land Surface Model Using the Local Ensemble Transform Kalman Filter
A land data assimilation system is developed to merge satellite soil moisture retrievals into the Joint U.K. Land Environment Simulator (JULES) land surface model (LSM) using the Local Ensemble Transform Kalman Filter (LETKF). The system assimilates microwave soil moisture retrievals from the Soil Moisture Active Passive (SMAP) radiometer and the Advanced Scatterometer (ASCAT) after bias correction based on cumulative distribution function fitting. The soil moisture assimilation estimates are evaluated with ground-based soil moisture measurements over the continental U.S. for five consecutive warm seasons (May–September of 2015–2019). The result shows that both SMAP and ASCAT retrievals improve the accuracy of soil moisture estimates. Especially, the SMAP single-sensor assimilation experiment shows the best performance with the increase of temporal anomaly correlation by ΔR ~ 0.05 for surface soil moisture and ΔR ~ 0.03 for root-zone soil moisture compared with the LSM simulation without satellite data assimilation. SMAP assimilation is more skillful than ASCAT assimilation primarily because of the greater skill of the assimilated SMAP retrievals compared to the ASCAT retrievals. The skill improvement also depends significantly on the region; the higher skill improvement in the western U.S. compared to the eastern U.S. is explained by the Kalman gain in the two experiments. Additionally, the regional skill differences in the single-sensor assimilation experiments are attributed to the number of assimilated observations. Finally, the soil moisture assimilation estimates provide more realistic land surface information than model-only simulations for the 2015 and the 2016 western U.S. droughts, suggesting the advantage of using satellite soil moisture retrievals in the current drought monitoring system.
SMAP↗
YBCO High-Temperature Superconducting Filters on M-Plane Sapphire Substrates
Since the discovery of High Temperature Superconductors (HTS) in 1986, microwave circuits have been demonstrated using HTS films on various substrates. These HTS-based circuits have proven to operate with less power loss than their metallic film counterparts at 77 K. This translates into smaller and lighter microwave circuits for space communication systems such as multiplexer filter banks. High quality HTS films have conventionally been deposited on lanthanum aluminate (LaAlO3) substrates. However, LaAlO3 has a relative dielectric constant (epsilon(sub r)) of 24. With a epsilon(sub r) approx. 9.4-11.6, sapphire (Al2O3) would be a preferable substrate for the fabrication of HTS-based components since the lower dielectric constant would permit wider microstrip lines to be used in filter design, since the lower dielectric constant would permit wider microstrip lines to be used for a given characteristic impedance (Z(sub 0)), thus lowering the insertion losses and increasing the power handling capabilities of the devices. We report on the fabrication and characterization of YBa2Cu3O(7-delta) (YBCO) on M-plane sapphire bandpass filters at 4.0 GHz. For a YBCO 'hairpin' filter, a minimum insertion loss of 0.5 dB was measured at 77 K as compared with 1.4 dB for its gold counterpart. In an 'edge-coupled' configuration, the insertion loss went down from 0.9 dB for the gold film to 0.8 dB for the YBCO film at the same temperature.
Sabataitis, J. C.↗
Fabrication of Compact Superconducting Lowpass Filters for Ultrasensitive Detectors
It is extremely important for current and future far-infrared and sub-millimeter ultrasensitive detectors, which include transition edge sensors (TES) and microwave kinetic inductance detectors, to be adequately filtered from stray electromagnetic radiation in order to achieve their optimal performance. One means of filtering stray radiation is to block leakage associated with electrical connections in the detector environment. Here we discuss a fabrication methodology for realizing non-dissipative planar filters imbedded in the wall of the detector enclosure to limit wave propagation modes up to far-infrared frequencies. Our methodology consists of fabricating a boxed stripline transmission line, in which a superconducting (Nb, Mo, or Al) transmission line is encased in a silicon dioxide dielectric insulator coated with a metallic shell. We report on achieved attenuation and return loss and find that it replicates the simulated data to a high degree.
Brown, Ari↗
Microwave transmission system for space power
The system considered makes use of a combined dipole antenna and rectifier. The dipole elements feed a balanced transmission line low-pass filter. A description of a laboratory model microwave power transmission system is given and a higher-power project with a longer range is discussed. Space power transmission experiments are also considered. It is pointed out that the investigations have shown that high overall transmission link efficiencies are possible.
Dickinson, R. M.↗
Novel Infrared-blocking Aerogel Scattering Filters and Their Applications in Astrophysical and Planetary Science Observations
Infrared-blocking scattering aerogel filters have a broad range of potential applications in astrophysics and planetary science observations in the far-infrared, sub-millimeter, and microwave regimes. Successful dielectric modeling of aerogel filters allowed the fabrication of samples to meet the mechanical and science instrument requirements for several experiments, including the Sub-millimeter Solar Observation Lunar Volatiles Experiment (SSOLVE), the Cosmology Large Angular Scale Surveyor (CLASS), and the Experiment for Cryogenic Large-Aperture Intensity Mapping (EXCLAIM). Thermal multi-physics simulations of the filters predict their performance when integrated into a cryogenic receiver. Prototype filters have survived cryogenic cycling to 4 K with no degradation in mechanical properties.
Kyle R Helson↗
The Application of the FDTD Method to Millimeter-Wave Filter Circuits Including the Design and Analysis of a Compact Coplanar
The finite difference time domain (FDTD) method is applied to the analysis of microwave, millimeter-wave and submillimeter-wave filter circuits. In each case, the validity of this method is confirmed by comparison with measured data. In addition, the FDTD calculations are used to design a new ultra-thin coplanar-strip filter for feeding a THz planar-antenna mixer.
Millimeter-wave filter Coplanar-Strip filter↗