Search NASA⌕ Search

SEARCH · Search NASA

Results for “mission applications”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

Low SWaP Semiconductor Laser Transmitter Modules For ASCENDS Mission Applications

The National Research Council's (NRC) Decadal Survey (DS) of Earth Science and Applications from Space has identified the Active Sensing of CO2 Emissions over Nights, Days, and Seasons (ASCENDS) as an important atmospheric science mission. NASA Langley Research Center, working with its partners, is developing fiber laser architecture based intensity modulated CW laser absorption spectrometer for measuring XCO2 in the 1571 nm spectral band. In support of this measurement, remote sensing of O2 in the 1260 nm spectral band for surface pressure measurements is also being developed. In this paper, we will present recent progress made in the development of advanced transmitter modules for CO2 and O2 sensing. Advanced DFB seed laser modules incorporating low-noise variable laser bias current supply and low-noise variable temperature control circuit have been developed. The 1571 nm modules operate at >80 mW and could be tuned continuously over the wavelength range of 1569-1574nm at a rate of 2 pm/mV. Fine tuning was demonstrated by adjusting the laser drive at a rate of 0.7 pm/mV. Heterodyne linewidth measurements have been performed showing linewidth ~200 kHz and frequency jitter ~75 MHz. In the case of 1260 nm DFB laser modules, we have shown continuous tuning over a range of 1261.4 - 1262.6 nm by changing chip operating temperature and 1261.0 - 1262.0 nm by changing the laser diode drive level. In addition, we have created a new laser package configuration which has been shown to improve the TEC coefficient of performance by a factor of 5 and improved the overall efficiency of the laser module by a factor of 2.

Prasad, Narasimha S.↗
NASA NTRS2002

Thin-Film Solar Array Earth Orbit Mission Applicability Assessment

This is a preliminary assessment of the applicability and spacecraft-level impact of using very lightweight thin-film solar arrays with relatively large deployed areas for representative Earth orbiting missions. The most and least attractive features of thin-film solar arrays are briefly discussed. A simple calculation is then presented illustrating that from a solar array alone mass perspective, larger arrays with less efficient but lighter thin-film solar cells can weigh less than smaller arrays with more efficient but heavier crystalline cells. However, a proper spacecraft-level systems assessment must take into account the additional mass associated with solar array deployed area: the propellant needed to desaturate the momentum accumulated from area-related disturbance torques and to perform aerodynamic drag makeup reboost. The results for such an assessment are presented for a representative low Earth orbit (LEO) mission, as a function of altitude and mission life, and a geostationary Earth orbit (GEO) mission. Discussion of the results includes a list of specific mission types most likely to benefit from using thin-film arrays. NASA Glenn's low-temperature approach to depositing thin-film cells on lightweight, flexible plastic substrates is also briefly discussed to provide a perspective on one approach to achieving this enabling technology. The paper concludes with a list of issues to be addressed prior to use of thin-film solar arrays in space and the observation that with their unique characteristics, very lightweight arrays using efficient, thin-film cells on flexible substrates may become the best array option for a subset of Earth orbiting missions.

Hoffman, David J.↗
NASA NTRS2019

NASA Plankton, Aerosol, Cloud, Ocean Ecosystem (PACE) Mission: Applications

PACE will extend and improve NASA's 20-plus years of global satellite observations of our living ocean, aerosols, and clouds and initiate an advanced set of climate-relevant data records. By determining the distribution of phytoplankton, PACE will help assess ocean health. It will also continue key measurements related to air quality and climate. This strategic mission is a Program of Record in the 2017 Decadal Survey for Earth Science and Applications for Space.

Kim, Grace↗
NASA NTRS2015

An Evaluation of the Impacts of AF-M315E Propulsion Systems for Varied Mission Applications

The purpose of the AF-M315E COMPASS study is to identify near-term (3-5 years) and long term (5 years +) opportunities for infusion, specifically the thruster and associated component technologies being developed as part of the GPIM project. Develop design reference missions which show the advantages of the AF-M315E green propulsion system. Utilize a combination of past COMPASS designs and selected new designs to demonstrate AF-M315E advantages. Use the COMPASS process to show the puts and takes of using AF-M315E at the integrated system level.

AF-M315E↗
NASA NTRS1994

Multimission Telemetry Visualization (MTV) system: A mission applications project from JPL's Multimedia Communications Laboratory

This paper describes the Multimission Telemetry Visualization (MTV) data acquisition/distribution system. MTV was developed by JPL's Multimedia Communications Laboratory (MCL) and designed to process and display digital, real-time, science and engineering data from JPL's Mission Control Center. The MTV system can be accessed using UNIX workstations and PC's over common datacom and telecom networks from worldwide locations. It is designed to lower data distribution costs while increasing data analysis functionality by integrating low-cost, off-the-shelf desktop hardware and software. MTV is expected to significantly lower the cost of real-time data display, processing, distribution, and allow for greater spacecraft safety and mission data access.

Koeberlein, Ernest, III↗
NASA NTRS1992

A comparison of superconductor and manganin technology for electronic links used in space mission applications

The electronic link connecting cryogenically cooled radiation detectors to data acquisition and signal processing electronics at higher temperatures contributes significantly to the total heat load on spacecraft cooling systems that use combined mechanical and cryogenic liquid cooling. Using high transition temperature superconductors for this link has been proposed to increase the lifetime of space missions. Herein, several YBCO (YBa2Cu3O7) superconductor-substrate combinations were examined and total heat loads were compared to manganin wire technology in current use. Using numerical solutions to the heat-flow equations, it is shown that replacing manganin technology with YBCO thick film technology can extend a 7-year mission by up to 1 year.

Caton, R.↗
NASA NTRS1986

A review of the multimegawatt MPD thruster and current mission applications

The magnetoplasmadynamic (MPD) thruster is potentially capable of providing 20-200 N of steady-state thrust, at 1000-20,000 s specific impulse while consuming a variety of propellants and megawatts of DC power. The specific impulse and power capacity put the MPD thruster in a class separate from other electric propulsion engines. Several types of missions are enhanced by the unique capabilities of a nuclear-electric driven MPD thruster and these include earth-orbit raising, cis-lunar transportation, and planetary exploration. This paper describes current MPD thruster technology, and several missions typical of the above cited categories.

King, D. Q.↗
NASA NTRS1984

Teleoperator Maneuvering System (TMS) mission applications and benefits

Studies conducted by NASA have shown that the operating range of the Shuttle can be substantially increased and cost of payload operation be decreased by making use of the Teleoperator Maneuvering System (TMS). The TMS is remotely controlled, free-flying, orbital mini-tug vehicle capable of performing a wide range of remote satellite services missions. It can operate out of the Shuttle cargo bay, from a space station, or on top of an upper stage like Centaur. For high energy missions up to and including geostationary orbit, the TMS propulsion stage will augment the Transfer Orbit Stage (TOS) recently proposed for commercial development in providing an effective low-cost second-stage system for delivering intermediate sized payloads to geosynchronous orbit (GEO). Attention is given to TMS capabilities for both long duration and short term orbital missions, taking into account also Space Station support operations.

Cramblit, D. C.↗
NASA NTRS2018

A Micro Newton Impulse-Bit Hydrazine Thruster - Design, Test, and Mission Applications

A small thruster, that will herein be called the Hydrazine milliNewton Thruster (HmNT), has been designed and vacuum hot-fire tested, demonstrating a range of thrust and impulse far below the current state-of-the-art (SOA) hydrazine thruster. Steady-state thrust levels of 35–135 mN, and minimum impulse-bits of 25–120 μN-s were demonstrated over a typical operating range of inlet pressures. These capabilities provide new spacecraft and mission design options, including the following: Functional backup for Reaction Wheel Assemblies (RWAs), which can be used to prolong the useful life of RWAs; RWA replacement for certain missions to save mass, power, and cost; Precision delta-V that can be used for: proximity operations and docking maneuvers, formation flying, primary attitude control for SmallSats and CubeSats, and primary delta-V for CubeSats.

Scharf, Daniel P.↗
NASA NTRS1976

Solar sail mission applications

The paper discusses the concept and the current baseline configuration of a reusable solar sail vehicle using light pressure for propulsion. The range of characteristic accelerations which solar sail vehicles might achieve during early years of operation is estimated to be from 0.2 to 1.3 mm/sq sec, with overall sail efficiency about 80 to 90%. Operating without the expenditure of propellant, the vehicle has the potential of delivering large payloads throughout the solar system. Detailed attention is given to various possible missions of the solar sail vehicle operating as an Interplanetary Shuttle. The vehicle may deliver payloads to the inner planets, asteroids, short period comets, or sun polar orbits and then return to earth, possibly with samples. It may also be used for outer planet missions or solar system escape. An 800-m sail may return samples totaling 200 kg from Mars and deliver them to an earth orbital laboratory. The first mission for the solar sail may be rendezvous with Halley's comet in 1982.

Wright, J. L.↗
NASA NTRS1974

Planetary mission applications for space storable propulsion

This paper presents the results of a study to compare space-storable with earth-storable spacecraft propulsion systems, space-storable with solid kick stages, and several space-storable development options on the basis of benefits received for cost expenditures required. The results show that, for a launch vehicle with performance less than that of Shuttle/Centaur, space-storable spacecraft propulsion offers an incremental benefit/cost ratio between 1.0 and 5.5 when compared to earth-storable systems for three of the four missions considered. In the case of VOIR 83, positive benefits were apparent only for a specific launch vehicle-spacecraft propulsion combination. A space-storable propulsion system operating at thrust of 600 lbf, 355 units of specific impulse, and with blowdown pressurization, represents the best choice for the JO 81 mission on a Titan/Centaur if only spacecraft propulsion modifications are considered. For still higher performance, a new solid-propellant kick stage with space-storable spacecraft propulsion is preferred over a system which uses space-storable propellants for both the kick stage and the spacecraft system.

Chase, R. L.↗
NASA NTRS1984

Orbital Maneuvering Vehicle (OMV) missions applications and systems requirements

The routine delivery of large payloads to low earth orbit has become a reality with the Space Transportation System (STS). However, once earth orbit has been achieved, orbit transfer operations represent an inefficient use of the Space Shuttle. The Orbital Maneuvering Vehicle (OMV) will add a new and needed dimension to STS capabilities. Utilized in a reusable manner, the OMV is needed to deliver and retrieve satellites to and from orbital altitudes or inclinations beyond the practical limits of the Space Shuttle and to support basic Space Station activities. The initial OMV must also be designed to permit the addition of future mission kits to support the servicing, module changeout, or refueling of satellites in Low Earth Orbit (LEO) and Geostationary Earth Orbit (GEO), and the retrieval and deorbit of space debris. This paper addresses the mission needs along with the resulting performance implications, design requirements and operational capabilities imposed on the OMV planned for use in the late 1980s.

Huber, W. G.↗
NASA NTRS1984

Preliminary analysis of space mission applications for electromagnetic launchers

The technical and economic feasibility of using electromagnetically launched EML payloads propelled from the Earth's surface to LEO, GEO, lunar orbit, or to interplanetary space was assessed. Analyses of the designs of rail accelerators and coaxial magnetic accelerators show that each is capable of launching to space payloads of 800 KG or more. A hybrid launcher in which EML is used for the first 2 KM/sec followed by chemical rocket stages was also tested. A cost estimates study shows that one to two EML launches per day are needed to break even, compared to a four-stage rocket. Development models are discussed for: (1) Earth orbital missions; (2) lunar base supply mission; (3) solar system escape mission; (4) Earth escape missions; (5) suborbital missions; (6) electromagnetic boost missions; and (7) space-based missions. Safety factors, environmental impacts, and EML systems analysis are discussed. Alternate systems examined include electrothermal thrustors, an EML rocket gun; an EML theta gun, and Soviet electromagnetic accelerators.

Miller, L. A.↗
NASA NTRS1979

Optimum design of spacecraft radiators for large capacity or long duration mission applications

Results of trade studies comparing optimum pumped fluid and hybrid heat pipe/pumped fluid radiator designs are presented. Design variables considered in the system optimization analyses include transport fluid properties and Reynolds number, pump loop component reliabilities, micrometeoroid protection, heat pipe spacing, manifolding and flow routing in pumped fluid designs, transport tubing spacing and diameters, and radiator fin parameters. Criteria for evaluating candidate radiator system designs include mass, radiator area, and overall system reliability. The studies show advantages in constructing large systems from small independent subsystems with oversizing to account for subsystem failures. The optimum size and survivability of the subsystems are identified as a function of the radiator construction, the system heat rejection requirements, the mission duration, and the system reliability requirements.

Leach, J. W.↗
NASA NTRSDate not supplied

Qualification of a Pulsed, Millinewton Class Metal Plasma Thruster for Broad Mission Applications

In the field of low power (<100W) electric propulsion, all thruster options demand significant trade-offs between operating parameters, reliability and scalable cost. With many systems on the market there are concerns with reliability, the need for extra considerations such as electron neutralizers for pure ion plumes, and the cost or craft compatibility of propellants. The Metal Plasma Thruster (MPT) is a new type of electric propulsion technology intended for low power applications. The system imparts momentum using inert, solid metal pucks as a propellant by using pulsed power to convert the metal into high velocity (~17km/s for Mo) jets of quasi-neutral plasma. The MPT technology does not require gas or liquid propellants, neutralizers, standby heaters, high voltage electronics, high electric or magnetic fields to operate. This comparatively simple pulsed operation is amenable to closed loop control, which provides for fine thrust control and S/C directed impulse on demand. Furthermore, the technology can use any metal as propellant, opening up unique opportunities for In-Situ Resource Utilization (ISRU) as well as customizability of performance for meeting specific mission needs. This paper describes implementation and direct measurement of this closed loop control mode as well as impulse measurement of multiple metals consistent with the aim of ISRU at NASA Glenn Research Center (GRC).

Electric Propulsion↗
NASA NTRSDate not supplied

Qualification of a Pulsed, Millinewton Class Metal Plasma Thruster for Broad Mission Applications

In the field of low power (<100W) electric propulsion, all thruster options demand significant trade-offs between operating parameters, reliability and scalable cost. With many systems on the market there are concerns with reliability, the need for extra considerations such as electron neutralizers for pure ion plumes, and the cost or craft compatibility of propellants. The Metal Plasma Thruster (MPT) is a new type of electric propulsion technology intended for low power applications. The system imparts momentum using inert, solid metal pucks as a propellant by using pulsed power to convert the metal into high velocity (~17km/s for Mo) jets of quasi-neutral plasma. The MPT technology does not require gas or liquid propellants, neutralizers, standby heaters, high voltage electronics, high electric or magnetic fields to operate. This comparatively simple pulsed operation is amenable to closed loop control, which provides for fine thrust control and S/C directed impulse on demand. Furthermore, the technology can use any metal as propellant, opening up unique opportunities for In-Situ Resource Utilization (ISRU) as well as customizability of performance for meeting specific mission needs. This paper describes implementation and direct measurement of this closed loop control mode as well as impulse measurement of multiple metals consistent with the aim of ISRU at NASA Glenn Research Center (GRC).

Electric Propulsion↗