Search NASA⌕ Search

SEARCH · Search NASA

Results for “nanodiamond”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Detonation Soot: A New Class of Ice Nucleating Particle

Abstract Temperatures and pressures from high explosive detonations far exceed atmospheric conditions in typical combustion reactions, and consequently, detonation soot forms with physiochemical properties distinct from soot formed by combustion. In this study, samples of detonation soot from two high explosives, PBX 9502 and Composition B‐3, were analyzed. Ice nucleation experiments on soot collected after controlled detonations were conducted in the laboratory to probe immersion and contact mode freezing. Samples nucleated ice at temperatures warmer than commercially available nanodiamonds, which has a mean nucleation temperature of −20.7°C. Ice nucleation rate coefficients increase rapidly by two to three orders of magnitude below −20°C for every sample. Size‐selected 137 μm diameter particles produced during detonation in an ambient air atmosphere yield bimodal distributions of freezing temperature with primary and secondary nucleation modes centered at −20°C and −13°C, respectively. The presence of a secondary mode allows for enhanced ice nucleation rate coefficients (one to two orders of magnitude greater than samples without a secondary mode) at temperatures outside the influence of the primary mode (>−17°C). Given the observed onset nucleation temperatures of −9.2°C, our results imply that detonation soot of the type studied here would only need to reach an altitude of approximately 4 km to facilitate ice formation.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

High field magnetometry with hyperpolarized nuclear spins

Abstract Quantum sensors have attracted broad interest in the quest towards sub-micronscale NMR spectroscopy. Such sensors predominantly operate at low magnetic fields. Instead, however, for high resolution spectroscopy, the high-field regime is naturally advantageous because it allows high absolute chemical shift discrimination. Here we demonstrate a high-field spin magnetometer constructed from an ensemble of hyperpolarized 13 C nuclear spins in diamond. They are initialized by Nitrogen Vacancy (NV) centers and protected along a transverse Bloch sphere axis for minute-long periods. When exposed to a time-varying (AC) magnetic field, they undergo secondary precessions that carry an imprint of its frequency and amplitude. For quantum sensing at 7T, we demonstrate detection bandwidth up to 7 kHz, a spectral resolution < 100mHz, and single-shot sensitivity of 410pT $$/\sqrt{{{{{{{{\rm{Hz}}}}}}}}}$$ / Hz . This work anticipates opportunities for microscale NMR chemical sensors constructed from hyperpolarized nanodiamonds and suggests applications of dynamic nuclear polarization (DNP) in quantum sensing.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Ultranarrow bright single-photon emitters in diamond with strong broadband phonon decoupling

Single-photon emitters are fundamental building blocks for quantum information processing, communication and sensing. However, unwanted interactions with bulk phonons in their host environment strongly limit their coherence and controllability. We report single color centers in nanodiamonds that are strongly and comprehensively decoupled from the bulk phononic environment. The color centers feature record-narrow linewidths down to 0.3 nm at room temperature and stable, bright emission, exceeding 10 Mcps in saturation. Notably, the bulk phonon sideband is almost entirely suppressed, revealing the presence of a single localized vibrational mode outside the diamond phonon band. Our observations and simulations point towards a unique mechanism for phonon decoupling in common wide-gap materials, based on a strongly radiative orbital transition coupled to a localized vibrational mode. The new color center enables qualitatively higher performance for applications in quantum networks and nanoscale sensing, and the exploration of new physical resources associated with vibrational states.

Sahoo, Swetapadma [ORNL]↗
DOE OSTI2022

Diamond and methane formation from the chemical decomposition of polyethylene at high pressures and temperatures

Abstract Polyethylene (C 2 H 4 ) n was compressed to pressures between 10 and 30 GPa in a diamond anvil cell (DAC) and laser heated above 2500 K for approximately one second. This resulted in the chemical decomposition of the polymer into carbon and hydrocarbon reaction products. After quenching to ambient temperature, the decomposition products were measured in the DAC at pressures ranging from ambient to 29 GPa using a combination of x-ray diffraction (XRD) and small angle x-ray scattering (SAXS). XRD identified cubic diamond and methane as the predominant product species with their pressure–volume relationships exhibiting strong correlations to the diamond and methane equations of state. Length scales associated with the diamond products, obtained from SAXS measurements, indicate the formation of nanodiamonds with a radius of gyration between 12 and 35 nm consistent with 32–90 nm diameter spherical particles. These results are in good agreement with the predicted product composition under thermodynamic and chemical equilibrium.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Single-particle chemical analysis reveals organic-rich detonation soot products

The detonation of high explosives produces a wide variety of particulate matter (PM) with distinct properties, not all of which are traditionally studied for chemical composition, formation processes, and forensic applications. We report particle-resolved measurements of Composition B detonation soot using soot particle aerosol mass spectrometry (SP-AMS), identifying carbonaceous species and metals not previously characterized on a single-particle basis. Results are combined with scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDS) to enhance source-dependent signatures. Black carbon, including graphitic carbon and detonation nanodiamonds, contributed 50.5-71.4% of PM 2.5 mass, while 22.5-43.4% was non-refractory organic carbon, a previously overlooked component that exhibited a complex and varying composition. Detonations were performed with and without PMMA confinement and under steady and overdriven conditions. Distinct particles enriched with polycyclic aromatic hydrocarbons (PAHs) were observed in experiments utilizing confinement, with quantities dependent on manufacturing method. SEM-EDS validated SP-AMS findings of metals internally mixed with carbonaceous species and extended the particle size range to 100 µm. This work makes detecting non-refractory organics using single-particle techniques more feasible for detonation forensics and understanding high-energy soot formation. While this analysis uses offline sample collection, SP-AMS could be deployed for in-situ measurements of detonation PM 2.5 transported in the atmosphere.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Robust quantification of the diamond nitrogen-vacancy center charge state via photoluminescence spectroscopy

Nitrogen vacancy (NV) centers in diamond are at the heart of many emerging quantum technologies, all of which require control over the NV charge state. Hence, methods for quantification of the relative photoluminescence intensities of the NV 0 and NV − charge states, i.e., a charge state ratio, are vital. Several approaches to quantify NV charge state ratios have been reported but are either limited to bulk-like NV diamond samples or yield qualitative results. We propose an NV charge state quantification protocol based on the determination of sample- and experimental setup-specific NV 0 and NV − reference spectra. The approach employs blue (400–470 nm) and green (480–570 nm) excitation to infer pure NV 0 and NV − spectra, which are then used to quantify NV charge state ratios in subsequent experiments via least squares fitting. We test our dual excitation protocol (DEP) for a bulk diamond NV sample and 20 and 100 nm nanodiamond particles and compare results with those obtained via other commonly used techniques such as zero-phonon line fitting and non-negative matrix factorization. We find that DEP can be employed across different samples and experimental setups and yields consistent and quantitative results for NV charge state ratios that are in agreement with our understanding of NV photophysics. By providing robust NV charge state quantification across sample types and measurement platforms, DEP will support the development of NV-based quantum technologies.

Color center laser spectroscopy↗
DOE OSTI2022

Diamond formation kinetics in shock-compressed C$-$H$-$O samples recorded by small-angle x-ray scattering and x-ray diffraction

Extreme conditions inside ice giants such as Uranus and Neptune can result in peculiar chemistry and structural transitions, e.g., the precipitation of diamonds or superionic water, as so far experimentally observed only for pure C$-$H and H 2 O systems, respectively. Here, we investigate a stoichiometric mixture of C and H 2 O by shock-compressing polyethylene terephthalate (PET) plastics and performing in situ x-ray probing. We observe diamond formation at pressures between 72 ± 7 and 125 ± 13 GPa at temperatures ranging from ~3500 to ~6000 K. Combining x-ray diffraction and small-angle x-ray scattering, we access the kinetics of this exotic reaction. The observed demixing of C and H 2 O suggests that diamond precipitation inside the ice giants is enhanced by oxygen, which can lead to isolated water and thus the formation of superionic structures relevant to the planets’ magnetic fields. Moreover, our measurements indicate a way of producing nanodiamonds by simple laser-driven shock compression of cheap PET plastics.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

High-precision chemical quantum sensing in flowing monodisperse microdroplets

A method is presented for high-precision chemical detection that integrates quantum sensing with droplet microfluidics. Using nanodiamonds (ND) with fluorescent nitrogen-vacancy (NV) centers as quantum sensors, rapidly flowing microdroplets containing analyte molecules are analyzed. A noise-suppressed mode of optically detected magnetic resonance is enabled by pairing controllable flow with microwave control of NV electronic spins, to detect analyte-induced signals of a few hundredths of a percent of the ND fluorescence. Using this method, paramagnetic ions in droplets are detected with low limit-of-detection using small analyte volumes, with exceptional measurement stability over >10 3 s. In addition, these droplets are used as microconfinement chambers by co-encapsulating ND quantum sensors with various analytes such as single cells, suggesting wide-ranging applications including single-cell metabolomics and real-time intracellular measurements from bioreactors. Important advances are enabled by this work, including portable chemical testing devices, amplification-free chemical assays, and chemical imaging tools for probing reactions within microenvironments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ultrafast quantum photonics enabled by coupling plasmonic nanocavities to strongly radiative antennas

Quantum emitters coupled to plasmonic nanostructures can act as exceptionally bright sources of single photons, operating at room temperature. Plasmonic mode volumes supported by these nanostructures can be several orders of magnitude smaller than the cubic wavelength, which leads to dramatically enhanced light–matter interactions and drastically increased photon production rates. However, when increasing the light localization further, these deeply subwavelength modes may in turn hinder the fast outcoupling of photons into free space. Plasmonic hybrid nanostructures combining a highly confined cavity mode and a larger antenna mode circumvent this issue. We establish the fundamental limits for quantum emission enhancement in such systems and find that the best performance is achieved when the cavity and antenna modes differ significantly in size. We experimentally support this idea by photomodifying a nanopatch antenna deterministically assembled around a nanodiamond known to contain a single nitrogen–vacancy (NV) center. As a result, the cavity mode shrinks, further shortening the NV fluorescence lifetime and increasing the single-photon brightness. Our analytical and numerical simulation results provide intuitive insight into the operation of these emitter–cavity–antenna systems and show that this approach could lead to single-photon sources with emission rates up to hundreds of THz and efficiencies close to unity.

47 OTHER INSTRUMENTATION↗
DOE OSTI2022

The importance of phonon spectrum measurements for accurate prediction of thermal scattering laws [Slides]

Although approximate phonon spectra (e.g. Debye model) are sufficient to reproduce integral quantities (e.g. total INS cross section) in reasonable agreement with the measured data, more accurate phonon spectra are needed to achieve agreement with the differential data. SANS component is essential for reproducing the total scattering cross section; this is the case for nanodiamonds and other materials where SANS components are present (such as porous materials like nuclear graphite). A format proposal for SANS data in ENDF or GNDS is needed. Therefore, differential (e.g. phonon spectrum) and integral (e.g. total cross section) measurements are necessary in the process of creating an ENDF evaluation. We have successfully developed a method by which ENDF evaluations can be directly compared to the relevant experimentally measured quantities. INS experiments at SNS, ILL, ISIS, and, in the future, ESS, as well as total cross section measurements at the VESUVIO instrument at ISIS, are accessible through user programs.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Abbreviated Technical Report: Experimentally Interrogating Detonation Chemistry on Sub-Nanosecond to Nanosecond Timescales

Direct experimental measurement of chemical reactions during high explosive detonation remains challenging. Theory and modeling have long preceded experiment in the fundamental physical and chemical kinetic properties of detonation, and experimentation at the relevant timescales are needed to both validate models and provide fundamental understanding of detonation. In this LDRD-ER project, two approaches, x-ray diffraction and core-level x-ray Raman, were developed and used to further experimental capabilities to address this gap. We further developed dynamic x-ray diffraction to directly detect nanodiamond formation during detonation, providing experimental data towards resolving longstanding controversy in the scientific literature, and although the full kinetics have not yet been fully mapped, diamond diffraction appears on the same timescales as detonation soot formation. In the second research thrust, we have developed core-level x-ray Raman for use with high explosives. This technique provides information analogous to x-ray absorption spectroscopy and electron energy loss spectroscopy, but uses inelastic scattering of hard x-rays that can interrogate chemistry around light elements much deeper into the material. The low cross section and requisite high solid angle collection have hindered its use for ultra-fast spectroscopy. We developed and tested a high-q spectrometer which will substantially increase cross section and signal-to-noise, showing this method will also not dramatically alter, compared to x-ray absorption, the most discriminating spectral features of C, N, and O from various high explosives and expected detonation products. We have also used x-ray Raman combined with OCEAN electronic structure calculations to explore dynamic photodegradation mechanisms in PETN and CL-20 explosives. This provides a pathway towards implementing capability to dynamically explore chemistry at an x-ray free electron laser.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Overview of Quantum Sensing Materials and Techniques for Energy Sector Applications

The energy sector is dependent upon highly sensitive sensing devices for a wide range of applications. Variables such as temperature, pH, electromagnetic fields, and pressure must be measured with high precision, often in harsh conditions (e.g. high temperature, pressure and humidity). These sensors are deployed in infrastructure such as transformers, pipelines, mines, nuclear power plants, and other areas to ensure safe operating conditions and uninterrupted, optimized service. Moreover, new opportunities for sensors have emerged due to the expansion of smart grids/meters, driverless vehicles, and the discovery of new oil/gas deposits. The continued maturation of quantum sensors offers exciting opportunities for quantum-enhanced measurements to improve sensitivity beyond the classical limit. Here, an overview of established and emerging quantum materials and methods for sensing applications will be provided. Opportunities within the energy sector for quantum sensors will then be analyzed, including oil/gas discovery, greenhouse gas emission monitoring, pH and ion sensing, current measurements, and quantum-enhanced spectroscopy, along with barriers such as quantum sensor platform miniaturization and ruggedization. A specific project at the National Energy Technology Laboratory involving the functionalization of qubits using metal-organic frameworks for enhanced quantum sensing will then be highlighted. Here, nitrogen vacancy centers (NV) in nanodiamonds, a commercially available qubit with long coherence times and utilizable quantum properties at room temperature, are encapsulated using the metal-organic framework ZIF-8. Significantly, the ZIF-8 coating increases the longitudinal spin relaxation lifetime of the NV centers, an important parameter for spin relaxometry-based quantum sensing experiments. These results demonstrate the importance of qubit functionalization as a crucial step for rationally designing high performance quantum sensors.

Crawford, Scott↗
DOE OSTI2025

Nitrogen Vacancy Center in Diamond for the Stress and Field Sensing Applications

The nitrogen-vacancy (NV) center in a nanodiamond (ND) crystal is a promising material for quantum information processing, sensing, and computing applications. It is one of the best candidate materials for quantum sensing and metrology expected to work at elevated temperatures and pressures conditions. We computationally show the effect of strain on the defect band edges and band gaps in the NV center diamond. A low energy Hamiltonian is developed for the ±1 spin manifold at the ground state. We show the quantum sensing device is a few orders of magnitude superior in sensing than the traditional optical sensing devices. We also discuss experimental results from the optically detected magnetic resonance (ODMR) and the spin relaxometry for the field sensing applications. The presentation concludes by providing a model for free spins detection of the rare earth ions.

field sensing applications↗
DOE OSTI2025

Comprehensive Diagnostics for Bond-Selective Nanocarbon Growth in Plasmas

This award was continuation funding for our previously supported efforts into carbon nanoparticle synthesis with tunable bond hybridization, including for luminescent carbon nanoparticles, amorphous carbon nanoparticles, and eventually nanodiamond. Beginning in early 2021 we supported preliminary experiments with in-house funds. In February 2021 our user proposal to the PCRF to investigate this topic was accepted and our experiments at PCRF took place in July 2022. DOE awarded this proposal to support data analysis based on those experiments, and supported the continued efforts towards finalizing that work. With those results and further efforts, we will be able to finalize our early research into nucleation and growth of carbon nanoparticles for a long-term objective of selective bonding in carbon and other nanomaterials grown in low-temperature plasmas. We made several important discoveries.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Low friction coatings

A low friction, wear-resistant surface operable at high temperatures and high loads with a low coefficient of friction including boron nitride and graphene-oxide on steel or nanodiamonds and graphene on aluminum. The low friction, wear-resistant surface remains with a coefficient of friction in the superlubric regime at temperatures in between about 200° C. and 970° C.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Electronic and Optical Properties of NV Center in Diamonds for Sensing Applications: Experimental and First Principles Density Functional Theory Approach

The nitrogen-vacancy (NV) center in a nanodiamond (ND) crystal is one of the best candidate materials for quantum sensing and metrology applications at elevated environmental conditions. The NV center can be used to achieve an unprecedented level of sensitivity for sensing applications at high temperatures and pressures. The NV center is also proven to be useful for magnetic field sensing. Furthermore, it can be used for applications in the sensing of valuable minerals such as rare earth elements (REEs) from the crude and waste subsurface materials. This work presents computational and experimental studies on electronic and optical properties of bulk diamond with N and NV defects. ND in MOF/polymer materials will be experimentally encapsulated. The transverse spin relaxation time of the NV center will be measured in bare and encapsulated ND. Different doping elements will be introduced on the surfaces and present surface electronic properties to study the surfaces with shallow NV center for quantum sensing applications.

Paudel, Hari P.↗
DOE OSTI2023

Nanodevice, method of making the same, and method of using the same

A nanodevice provides for electric-field control of magnon-QSD interactions. The nanodevice includes a ferroelectric substrate, a ferromagnetic material disposed over the ferroelectric substrate, and a nanodiamond including an ensemble of nitrogen-vacancy (NV) spins, each NV magnetically interfacing with the ferromagnetic material. An electric field is measured by applying a voltage across the ferroelectric substrate and the ferromagnetic material, changing a magnon excitation spectrum of the ferromagnetic material with respect to an electron spin resonance frequency of the ensemble of NV spins, and measuring a relaxation rate of the ensemble of NV spins.

Shalaev, Vladimir M.↗
DOE OSTI2024

Nitrogen Vacancy Centers in Diamond for Stress Sensing Applications: Theory and Experiments

Sensing of stress under high elevated environmental conditions with high resolution has critical importance for range of applications including earth’s subsurface scanning and geological CO2 storage monitoring. Using first principles density functional theory (DFT) approach combined with the theoretical modelling of low energy Hamiltonian, here we investigate a novel approach to detect unprecedented level of pressure by taking advantage of solid-state electron’s spin of Nitrogen vacancy (NV) centers in nanodiamond. We computationally explore the effect of strain on the defect band edges and band gaps by varying the lattice parameters of diamond supercell hosting a single NV center. A low energy Hamiltonian is developed that includes effect of stress on the energy level of ±1 spin manifold at the ground state. By quantifying the energy level shift and split, we predict the pressure sensing of up to 0.3 MPa/√Hz. We show superiority of the quantum sensing over traditional optical sensing techniques by discussing our results from DFT and theoretical modelling for the frequency shift per unit pressure. The proposed quantum stress sensing could be useful to measure earth’s subsurface vibrations. Our results open avenues for development of sensing technology with a high sensitivity and resolution under extreme pressure conditions that potentially has a wider applicability than existing pressure sensing technologies.

Paudel, Hari P.↗