SEARCH · Search NASA

Results for “o Wing aerodynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1954

A Transonic Wind-Tunnel Investigation of the Longitudinal Aerodynamic Characteristics of a Model of the Lockheed XF-104 Airplane

The transonic longitudinal aerodynamic characteristics of a 0.0858-scale model of the Lockheed XF-104 airplane have been obtained from tests at the Langley 16-foot transonic tunnel. The results of the investigation provide some general information applicable to the transonic properties of thin, low-aspect-ratio, unswept wing configurations utilizing a high horizontal tail . The model employs a horizontal tail mounted at the top of the vertical tail and a wing with an aspect ratio of 2.5, a taper ratio of 0.385, and 3.4-percent-thick airfoil sections. The lift, drag, and static longitudinal pitching moment were measured at Mach numbers from 0.80 t o 1.09 and angles of attack from -2.5 deg to 22.5 deg. Some of the dynamic longitudinal stability properties of the airplane have been predicted from the test results. In addition, some visual flow studies on the wing surfaces obtained at Mach numbers of 0.80 and 1.00 are included. Results of the investigation show that the transonic rise in drag coefficient at zero lift is about 0.030. At high angles of attack, the model becomes longitudinally unstable at Mach numbers from 0.80 t o 0.90, whereas a reduction in static stability is experienced when very high angles of attack are reached at Mach numbers above 0.90. Longitudinal dynamic stability calculations show that the longitudinal control is good at angles of attack below the unstable break in the static pitching-moment curves, but a typical corrective control applied after the occurrence of neutral stability has little effect in averting pitch-up.

Hieser, Gerald↗

NASA NTRS1982

Advanced technologies applied to reduce the operating costs of small commuter transport aircraft

The application of new aerodynamic, structural, and propulsion technologies to a specified baseline commuter aircraft is studied. The assessment models can be used on a desktop calculator and include a sizing program, operating cost program, and passenger ride qualities model. Evaluation is done with a step-by-step approach and is applied to range, number and type of engines, structure, wing selection, and configuration. A 40 percent direct operating cost saving is anticipated compared to current well established commuter aircraft.

Masefield, O.↗

NASA NTRS1983

Low-speed tests of a high-aspect-ratio, supercritical-wing transport model equipped with a high-lift flap system in the Langley 4- by 7-meter and Ames 12-foot pressure tunnels

The Ames 12-Foot Pressure Tunnel was used to determine the effects of Reynolds number on the static longitudinal aerodynamic characteristics of an advanced, high-aspect-ratio, supercritical wing transport model equipped with a full span, leading edge slat and part span, double slotted, trailing edge flaps. The model had a wing span of 7.5 ft and was tested through a free stream Reynolds number range from 1.3 to 6.0 x 10 to 6th power per foot at a Mach number of 0.20. Prior to the Ames tests, an investigation was also conducted in the Langley 4 by 7 Meter Tunnel at a Reynolds number of 1.3 x 10 to 6th power per foot with the model mounted on an Ames strut support system and on the Langley sting support system to determine strut interference corrections. The data obtained from the Langley tests were also used to compare the aerodynamic charactertistics of the rather stiff, 7.5-ft-span steel wing model tested during this investigation and the larger, and rather flexible, 12-ft-span aluminum-wing model tested during a previous investigation. During the tests in both the Langley and Ames tunnels, the model was tested with six basic wing configurations: (1) cruise; (2) climb (slats only extended); (3) 15 deg take-off flaps; (4) 30 deg take-off flaps; (5) 45 deg landing flaps; and (6) 60 deg landing flaps.

Morgan, H. L., Jr.↗

NASA NTRS1986

Subsonic aerodynamic characteristics of a circular body earth-to-orbit transport

To reduce the weight and improve the performance of future earth-to-orbit transports, the use of circular cross sections in the fuselage bodies of these vehicles is being considered at the Langley Research Center. Structurally, circular cross sections are stronger and lighter than other shapes. A study has been made applying the circular body concept to a vertical-takeoff, delta-winged, single-stage-to-orbit transport. A 52 in., 0.022-scale model of the circular body vehicle was tested at a Mach number of 0.3 in the 7 x 10 ft High Speed Wind Tunnel at the Langley Research Center to obtain aerodynamic forces and moments. Oil-flow photographs were taken at several angles of attack to aid in the aerodynamic analysis. Model control surfaces included elevons and ailerons for the evaluation of pitch and roll characteristics and either wing-tip fins, a nose mounted dorsal fin, or a conventional vertical tail for the evaluation of yaw characteristics. Other deflecting surfaces included speedbrakes and body flaps. Basic data on longitudinal flight characteristics are shown, including lift, drag, and pitching moments. Comparisons of the directional stability and control effectiveness of the three directional control devices are also shown.

Lepsch, R. A., Jr.↗

NASA NTRS1976

Experimental effects of fuselage camber on longitudinal aerodynamic characteristics of a series of wing-fuselage configurations at a Mach number of 1.41

An experimental investigation was conducted to evaluate a method for the integration of a fighter-type fuselage with a theoretical wing to preserve desirable wing aerodynamic characteristics for efficient maneuvering. The investigation was conducted by using semispan wing fuselage models mounted on a splitter plate. The models were tested through an angle of attack range at a Mach number of 1.41. The wing had a leading edge sweep angle of 50 deg and an aspect ratio of 2.76; the wing camber surface was designed for minimum drag due to lift and was to be self trimming at a lift coefficient of 0.2 and at a Mach number of 1.40. A series of five fuselages of various camber was tested on the wing.

Dollyhigh, S. M.↗

NASA NTRS1993

Aerodynamic configuration design using response surface methodology analysis

An investigation has been conducted to determine a set of optimal design parameters for a single-stage-to-orbit reentry vehicle. Several configuration geometry parameters which had a large impact on the entry vehicle flying characteristics were selected as design variables: the fuselage fineness ratio, the nose to body length ratio, the nose camber value, the wing planform area scale factor, and the wing location. The optimal geometry parameter values were chosen using a response surface methodology (RSM) technique which allowed for a minimum dry weight configuration design that met a set of aerodynamic performance constraints on the landing speed, and on the subsonic, supersonic, and hypersonic trim and stability levels. The RSM technique utilized, specifically the central composite design method, is presented, along with the general vehicle conceptual design process. Results are presented for an optimized configuration along with several design trade cases.

Engelund, Walter C.↗

NASA NTRS1984

A study of prediction methods for the high angle-of-attack aerodynamics of straight wings and fighter aircraft

Work is described dealing with two areas which are dominated by the nonlinear effects of vortex flows. The first area concerns the stall/spin characteristics of a general aviation wing with a modified leading edge. The second area concerns the high-angle-of-attack characteristics of high performance military aircraft. For each area, the governing phenomena are described as identified with the aid of existing experimental data. Existing analytical methods are reviewed, and the most promising method for each area used to perform some preliminary calculations. Based on these results, the strengths and weaknesses of the methods are defined, and research programs recommended to improve the methods as a result of better understanding of the flow mechanisms involved.

Mcmillan, O. J.↗

NASA NTRS1978

Aerodynamic characteristics of a fixed arrow-wing supersonic cruise aircraft at Mach numbers of 2.30, 2.70, and 2.95

Tests were conducted in the Langley Unitary Plan wind tunnel at Mach numbers of 2.30. 2.70, and 2.95 to determine the performance, static stability, and control characteristics of a model of a fixed-wing supersonic cruise aircraft with a design Mach Number of 2.70 (SCAT 15-F-9898). The configuration had a 74 deg swept warped wing with a reflexed trailing edge and four engine nacelles mounted below the reflexed portion of the wing. A number of variations in the basic configuration were investigated; they included the effect of wing leading edge radius, the effect of various model components, and the effect of model control deflections.

Morris, O. A.↗

NASA NTRS1972

Design integration and noise studies for jet STOL aircraft. Volume 1: Program summary

This program was undertaken to develop, through analysis, design, experimental static testing, wind tunnel testing, and design integration studies, an augmentor wing jet flap configuration for a jet STOL transport aircraft having maximum propulsion and aerodynamic performance with minimum noise generation. The program had three basic elements: (1) static testing of a scale wing section to demonstrate augmentor performance and noise characteristics; (2) two-dimensional wind tunnel testing to determine flight speed effects on performance; and (3) system design and evaluation which integrated the augmentor information obtained into a complete system and ensured that the design was compatible with the requirements for a large STOL transport having a 500-ft sideline noise of 95 PNdB or less. This objective has been achieved.

Okeefe, V. O.↗

NASA NTRS1972

Space shuttle: Longitudinal aerodynamic characteristics of low aspect ratio wing configurations in ground effect for a moving and stationary ground surface

A 0.05-scale model of the NASA-MSC Orbiter 040A Configuration was tested. Test duration was approximately 80 hours during which the model was tested in and out of ground effect with a stationary and moving ground belt. Model height from ground plane surface was varied from one and one-half wing span to landing touchdown while angle of attack varied from -4 to 20 degrees. Eleven effectiveness and alternate configuration geometries were tested to insure complete analysis of low aspect ratio wing aircraft in the presence of ground effect. Test Mach number was approximately 0.067 with a corresponding dynamic pressure value of 6.5 psf.

Romere, P. O.↗

NASA NTRS1991

Simulation of iced wing aerodynamics

The sectional and total aerodynamic load characteristics of moderate aspect ratio wings with and without simulated glaze leading edge ice were studied both computationally, using a three dimensional, compressible Navier-Stokes solver, and experimentally. The wing has an untwisted, untapered planform shape with NACA 0012 airfoil section. The wing has an unswept and swept configuration with aspect ratios of 4.06 and 5.0. Comparisons of computed surface pressures and sectional loads with experimental data for identical configurations are given. The abrupt decrease in stall angle of attack for the wing, as a result of the leading edge ice formation, was demonstrated numerically and experimentally.

Potapczuk, M. G.↗

NASA NTRS1991

Simulation of iced wing aerodynamics

Potapczuk, M. G.↗

NASA NTRS1976

Application of advanced technology to future long-range aircraft

The objective of this paper is to provide an overview assessment of three separate programs at Langley Research Center that have incorporated advanced technology into the design of long-range passenger and cargo aircraft. The first technology centers around the use of an span-loaded cargo aircraft with the payload distributed along the wing. This concept has the potential for reduced structural weights. The second technology is the application of laminar flow control (LFC) to the aircraft to reduce the aerodynamic drag. The use of LFC can reduce the fuel requirements during long-range cruise. The last program evaluates the production of alternate aircraft fuels from coal and the use of liquid hydrogen as an aircraft fuel. Coal-derived hydrogen as an aircraft fuel offers both the prospect for reduced dependence on petroleum fuels and improved performance for long-range aircraft.

Schrader, O. E.↗

NASA NTRS1991

Engineering method for aero-propulsive characteristics at hypersonic Mach numbers

An engineering method has been developed for the rapid analysis of external aerodynamics and propulsive performance characteristics of airbreathing vehicles at hypersonic Mach numbers. This method, based on the theory of characteristics, has been developed to analyze fuselage-wing body combinations and body flaps with blunt or sharp leading/trailing edges. Arbitrary ratio of specific heat for the flowing medium can be specified in the program. Furthermore, the capability exists in the code to compute the inviscid inlet mass capture and momentum flux. The method is under development for computations of pressure distribution, and flow characteristics in the inlet, along with the effect of viscosity. Correlative studies have been performed for representative hypersonic configurations using the current method. The results of these correlations for various aerodynamics parameters are encouraging.

Goradia, Suresh↗

NASA NTRS2019

Comparative Study of Active Flow Control Strategies for Lift Enhancement of a Simplified High-Lift Configuration

Numerical simulations have been performed for a simplified high-lift (SHL) version of the Common Research Model (CRM) configuration, where the Fowler flaps of the conventional high-lift (CRM-HL) configuration are replaced by a set of simple hinged flaps. These hinged flaps are equipped with integrated modular active flow control (AFC) cartridges on the suction surface, and the resulting geometry is known as the CRM-SHL-AFC configuration. The main objective is to make use of AFC devices on the CRM-SHL-AFC configuration to recover the aerodynamic performance (lift) of the CRM-HL configuration. In the current paper, a Lattice Boltzmann method-based computational fluid dynamics (CFD) code, known as PowerFLOWQ® is used to simulate the entire flow field associated with the CRM-SHL-AFC configuration equipped with several different types of AFC devices. The transonic version of the PowerFLOWQ® code that has been validated for high speed flows is used to accurately simulate the flow field generated by the high-momentum actuators required to mitigate reversed flow regions on the suction surfaces of the main wing and the flap. The numerical solutions predict the expected trends in aerodynamic forces as the actuation levels are increased. More efficient AFC systems and actuator arrangements emerged based on the parametric studies performed prior to a Fall 2018 wind tunnel test. Preliminary comparisons of the numerical solutions for lift and surface pressures are presented here with the experimental data, demonstrating the usefulness of CFD for predicting the flow field and lift characteristics of AFC-enabled high-lift configurations.

Vatsa, Veer N.↗

NASA NTRS1982

Effect of nozzle and vertical-tail variables on the performance of a 3-surface F-15 model at transonic Mach numbers

An investigation was conducted in the Langley 16 foot transonic tunnel to determine the longitudinal aerodynamic characteristics of twin two dimensional nozzles and twin baseline axisymmetric nozzles installed on a fully metric 0.047 scale model of the F-15 three surface configuration (canards, wing, horizontal tails). The effects on performance of two dimensional nozzle in flight thrust reversing, locations and orientation of the vertical tails, and deflections of the horizontal tails were also determined. Test data were obtained at static conditions and at Mach numbers from 0.60 to 1.20 over an angle of attack range from -2 deg to 15 deg. Nozzle pressure ratio was varied from jet off to about 6.5.

Pendergraft, O. C., Jr.↗

NASA NTRS1977

Over-the-wing model thrust reverser noise tests

Experimental results are presented for static acoustic tests of a 1/12 scale model over-the-wing target type thrust reverser. The model configuration simulates a design that is applicable to the over-the-wing short-haul advanced technology engine. Aerodynamic screening tests of a variety of reverser designs identified configurations that satisfied a reverse thrust requirement of 35 percent of forward thrust at a nozzle pressure ratio of 1.29. The variations in the reverser configuration included, blocker door angle, blocker door lip angle and shape, and side skirt shape. Acoustic data are presented and compared for the various configurations. The model data scaled to a single full size engine show that peak free field perceived noise levels at a 152.4 meter sideline distance range from 98 to 104 PNdB.

Goodykoontz, J.↗

NASA NTRS1938

The effects of partial-span plain flaps on the aerodynamic characteristics of a rectangular and a tapered Clark Y wing

An investigation was made to determine the aerodynamic characteristics of tapered and rectangular wings with partial-span plain flaps. Two Clark Y airfoils equipped with center section and with tip-section flaps were tested. The results showed that the aerodynamic characteristics of partial-span plain flaps were, in general, similar to those of split flaps of the same span, but that the lift and the drag were less for the wing with plain flaps than for the wing with split flaps of comparable size. For the rectangular wing with center-section plain flaps, the maximum lift and the lift-drag ratio at maximum lift were greater and the drag at maximum lift was less than for the wing with tip-section plain flaps of the same size. The maximum lift of the tapered wing varied in the same manner as that of the rectangular wing but the drag and the lift-drag-ratio relationship were opposite.

House, R O↗