Results for “offset fed” — Page 4

NASA NTRS1990

Fan beam generated by a linear-array fed parabolic reflector

The theoretical background and the results of computer simulations and experimental studies for a parabolic reflector fed by a linear array are detailed. The concept of using a parabolic reflector antenna fed by a small linear array to generate fan-beam patterns is validated. Large angle scan along the broad-beam direction of the fan beam can be achieved by offsetting the linear array laterally. It is both empirically and numerically demonstrated that the array feed must be displaced in the reflector's axial direction to an optimum location from the focal plane in order to achieve the best antenna gain performance. As a result, the linear-array-fed parabolic reflector can be used in place of a long planar array in a multifunctional reflector antenna system.

Huang, John↗

NASA NTRS1984

Three stage rocket vehicle with parallel staging

A three stage rocket vehicle has a large forward propellant tank and a small aft propellant tank axially aligned. Secured to the rear end of the aft propellant tank is an engine mount structure carrying rocket engines. Offset and secured to the propellant tanks is a payload structure. The propellants from the large forward tank are fed into the aft propellant tank. This arrangement enables the vehicle to parallel stage its use of engines and components and results in significant payload capability. The design and components fully utilize existing space shuttle elements and tooling.

Marshall, W. R.↗

DOE OSTI2025

Feedstock-efficient conversion through hydrogen and formate-driven metabolism in Escherichia coli

Product yields for biomanufacturing processes are often constrained by the tight coupling of cellular energy generation and carbon metabolism in sugar-based fermentation systems. To overcome this limitation, we engineered Escherichia coli to utilize hydrogen gas (H 2 ) and formate (HCOO - ) as alternative sources of energy and reducing equivalents, thereby decoupling energy generation from carbon metabolism. This approach enabled precise suppression of decarboxylative oxidation during acetate growth, with 86.6 ± 1.6 % of electrons from hydrogen gas (via soluble hydrogenase from Cupriavidus necator H16) and 98.4 ± 3.6 % of electrons from formate (via formate dehydrogenase from Pseudomonas sp. 101) offsetting acetate oxidation. Hydrogen gas supplementation led to a titratable and stoichiometric reduction in CO 2 evolution in acetate-fed cultures. Metabolomic analysis suggests that this metabolic decoupling redirects carbon flux through the glyoxylate shunt, partially bypassing two decarboxylative steps in the TCA cycle. Here, we demonstrated the utility of this strategy by applying it to mevalonate biosynthesis, where formate supplementation during glucose fermentation increased titers by 57.6 % in our best-performing strain. Flux balance analysis further estimated that 99.0 ± 2.8 % of electrons from formate were used to enhance mevalonate production. These findings highlight a broadly applicable strategy for enhancing biomanufacturing efficiency by leveraging external reducing power to optimize feedstock and energy use.

Biomanufacturing↗

NASA NTRS1972

Shaped Beam KU-Band Antenna Design

Antenna systems for a Ku-band synchronous orbit communications satellite were considered. A multiple beam offset feed cluster used in conjunction with an offset parabolic reflector was chosen for the antenna realization. For radiating elements in the feed array, polyrod or dielectric rod radiators fed by waveguide are investigated. Polyrod antennas shrink the cross section of the waveguide required, are fairly directive, and can be tapered to reduce sidelobes. As a consequence, it is thought that mutual coupling effects between adjacent elements will be minimal and the resultant physically small elements will allow greater packing densities for the drive elements in the feed array than would otherwise be possible.

Dudgeon, J. E.↗

NASA NTRS1977

Servo corrects interferometer-mirror tilt

Three detectors sense He-Ne laser beam; one senses reference phase while others, at right angles to first, sense phase offset for each axis. Analog output of axis detectors is multiplied separately by reference output to give X and Y error signals that are then fed to respective X and Y actuators.

Schindler, R. A.↗

NASA NTRS1996

Capaciflector-guided mechanisms

A plurality of capaciflector proximity sensors, one or more of which may be overlaid on each other, and at least one shield are mounted on a device guided by a robot so as to see a designated surface, hole or raised portion of an object, for example, in three dimensions. Individual current-measuring voltage follower circuits interface the sensors and shield to a common AC signal source. As the device approaches the object, the sensors respond by a change in the currents therethrough. The currents are detected by the respective current-measuring voltage follower circuits with the outputs thereof being fed to a robot controller. The device is caused to move under robot control in a predetermined pattern over the object while directly referencing each other without any offsets, whereupon by a process of minimization of the sensed currents, the device is dithered or wiggled into position for a soft touchdown or contact without any prior contact with the object.

Vranish, John M.↗

NASA NTRS1997

A Spherical to Plane Wave Transformation Using a Reflectarray

A reflectarray has generally been used as a replacement for a reflector antenna. Using in this capacity, different configurations (prime focus, offset etc.) and various applications (dual frequency, scanning etc.) have been demonstrated with great success. Another potential application that has not been explored previously is the use of reflectarrays to compensate for phase errors in space power combining applications such as space-fed lens and power combining amplifier. In these applications, it is required to convert a spherical wave to a plane wave with proper phase correction added to each element of the reflectarray. This paper reports an experiment to investigate the feasibility of using a reflectarray as an alternative to a lens in space power combining. The experiment involves transforming a spherical wave from a orthomode horn to a plane wave at the horn aperture. The reflcctarray consists of square patches terminated in open stubs to provide necessary phase compensation. In this paper, preliminary results will be presented and the feasibility of such compensation scheme will be discussed.

Zaman, Afroz J.↗

NASA NTRS1989

A space qualified thermal imaging system using a Pt Si detector array

EDO Corporation, Barnes Engineering Division designed and constructed a high resolution thermal imaging system on contract to Lockheed for use in the SDI Star Lab. This employs a Pt Si CCD array which is sensitive in the spectral range of 3 to 5 microns. Star Lab will be flown in the Shuttle bay and consists basically of a large, reflecting, tracking telescope with associated sensors and electronics. The thermal imaging system is designed to operate in the focal plane of this telescope. The configuration of the system is illustrated. The telescope provides a collimated beam output which is focussed onto the detector array by a silicon objective lens. The detector array subtends a field of view of 1.6 degrees x 1.22 degrees. A beam switching mirror permits bypassing the large telescope to give a field of 4 degrees x 3 degrees. Two 8 position filter wheels are provided, and background radiation is minimized by Narcissus mirrors. The detector is cooled with a Joule-Thompson cryostat fed from a high pressure supply tank. This was selected instead of a more convenient closed-cycle system because of concern with vibration. The latter may couple into the extremely critical Starlab tracking telescope. The electronics produce a digitized video signal for recording. Offset and responsivity correction factors are stored for all pixels and these corrections are made to the digitized output in real time.

Astheimer, Robert W.↗

NASA NTRS1998

Reflectarray Demonstrated to Transform Spherical Waves into Plane Waves

The development of low-cost, high-efficiency array antennas has been the research focus of NASA Lewis Research Center's Communications Technology Division for the past 15 years. One area of current interest is reflectarray development. Reflectarrays have generally been used to replace reflector antennas. In this capacity, different configurations (such as prime focus and offset) and various applications (such as dual frequency and scanning) have been demonstrated with great success. One potential application that has not been explored previously is the use of reflectarrays to compensate for phase errors in space-power-combining applications, such as a space-fed lens and power-combining amplifiers. Recently, we experimentally investigated the feasibility of using a reflectarray as an alternative to a dielectric lens for such applications. The experiment involved transforming the spherical waves from an orthomode horn to plane waves at the horn aperture. The reflectarray consists of square patches terminated in open stubs to provide the necessary phase compensation.

Zaman, Afrosz J.↗

NASA NTRS2010

RF Device for Acquiring Images of the Human Body

A safe, non-invasive method for forming images through clothing of large groups of people, in order to search for concealed weapons either made of metal or not, has been developed. A millimeter wavelength scanner designed in a unique, ring-shaped configuration can obtain a full 360 image of the body with a resolution of less than a millimeter in only a few seconds. Millimeter waves readily penetrate normal clothing, but are highly reflected by the human body and concealed objects. Millimeter wave signals are nonionizing and are harmless to human tissues when used at low power levels. The imager (see figure) consists of a thin base that supports a small-diameter vertical post about 7 ft (=2.13 m) tall. Attached to the post is a square-shaped ring 2 in. (=5 cm) wide and 3 ft (=91 cm) on a side. The ring is oriented horizontally, and is supported halfway along one side by a connection to a linear bearing on the vertical post. A planar RF circuit board is mounted to the inside of each side of the ring. Each circuit board contains an array of 30 receivers, one transmitter, and digitization electronics. Each array element has a printed-circuit patch antenna coupled to a pair of mixers by a 90 coupler. The mixers receive a reference local oscillator signal to a subharmonic of the transmitter frequency. A single local oscillator line feeds all 30 receivers on the board. The resulting MHz IF signals are amplified and carried to the edge of the board where they are demodulated and digitized. The transmitted signal is derived from the local oscillator at a frequency offset determined by a crystal oscillator. One antenna centrally located on each side of the square ring provides the source illumination power. The total transmitted power is less than 100 mW, resulting in an exposure level that is completely safe to humans. The output signals from all four circuit boards are fed via serial connection to a data processing computer. The computer processes the approximately 1-MB data set into a three-dimensional image in a matter of seconds. The innovation is to configure the receiver array in a ring topology surrounding the scanned object. The ring is then scanned vertically to cover the necessary two-dimensional surface. This fabrication of the ring is made possible by using planar antenna and circuit technology. A planar circuit board serves as a medium for both antennas and signal processing components. Using this technique, parts counts are kept low, and the cost per element is a small fraction of a waveguide-based system.

Gaier, Todd C.↗

NASA NTRSDate not supplied

Hazard Boresight Relative Navigation for Safe Lunar Landing

In the area of planetary landing, hazard detection and avoidance is the act of driving a vehicle to a safe landing area using onboard resources. A hazard detection sensor is used to scan the terrain and these measurements are evaluated to determine where the safe landing sites are located. The selected site is generally not the same as the nominal target, so the vehicle must divert to the new site. This activity involves the interaction between several components, including a suite of onboard GNC algorithms that work together to efficiently choose and divert to a new site. This paper presents the Hazard Boresight Relative Navigation concept, which is a method that provides a common interface between the hazard scan, safe-site selection algorithm, size of the target-relative landing ellipse, divert offset distance and guidance targeting algorithm. After the safe-site is selected from the hazard scan, the original inertial target is replaced with a vehicle-relative target, which is initialized by a measurement from the hazard scan. The new target-relative position state is estimated over time in the navigation filter, and is fed to the guidance algorithm to perform the divert maneuver. In addition to detailing the Hazard Boresight Relative Navigation concept, this paper also presents some general landing terms that can be used in the greater discussion, as well as analysis on how to estimate and predict the vehicle footprint dispersion ellipse during flight, which is used in the safe-site selection algorithm.

Stephen R. Steffes↗

NASA NTRSDate not supplied

Hazard Boresight Relative Navigation for Safe Lunar Landing

In the area of planetary landing, hazard detection and avoidance is the act of driving a vehicle to a safe landing area using onboard resources. A hazard detection sensor is used to scan the terrain and these measurements are evaluated to determine where the safe landing sites are located. The selected site is generally not the same as the nominal target, so the vehicle must divert to the new site. This activity involves the interaction between several components, including a suite of onboard GNC algorithms that work together to efficiently choose and divert to a new site. This paper presents the Hazard Boresight Relative Navigation concept, which is a method that provides a common interface between the hazard scan, safe-site selection algorithm, size of the target-relative landing ellipse, divert offset distance and guidance targeting algorithm. After the safe-site is selected from the hazard scan, the original inertial target is replaced with a vehicle-relative target, which is initialized by a measurement from the hazard scan. The new target-relative position state is estimated over time in the navigation filter, and is fed to the guidance algorithm to perform the divert maneuver. In addition to detailing the Hazard Boresight Relative Navigation concept, this paper also presents some general landing terms that can be used in the greater discussion, as well as analysis on how to estimate and predict the vehicle footprint dispersion ellipse during flight, which is used in the safe-site selection algorithm.

Stephen Steffes↗

NASA NTRS2003

High Power mm-Wave Transmitter System for Radar or Telecommunications

Future NASA deep space missions able to provide tens of kilo-watts of spacecraft DC power, make it feasible to employ high power RF telecommunications systems. Traditional flight systems (e.g., Cassini), constrained by limited DC power, used a single high-gain 4m Cassegrain reflector fed by a single lower power (20W) transmitter. Increased available DC power means that high power (1000 W) transmitters can be used. Rather than continue building traditional single-transmitter systems it now becomes feasible to engineer and build multi-element active arrays that can illuminate a dish. Illuminating a 2m dish with a spherical wavefront from an offset 1kW active array can provide sufficient ERP (Effective Radiated Power) when compared to a larger Cassegrain dish. Such a system has the advantage of lower mass, lower volume, improved reliability, less stringent pointing requirements, lower cost and risk. We propose to design and build a prototype Ka-band transmit antenna with an active sub-array using 125W TWTAs. The system could be applied to a telecommunications downlink or radar transmitter used for missions such as JIMO.

Stride, S. L.↗

NASA NTRS2009

Multi-Modulator for Bandwidth-Efficient Communication

A modulator circuit board has recently been developed to be used in conjunction with a vector modulator to generate any of a large number of modulations for bandwidth-efficient radio transmission of digital data signals at rates than can exceed 100 Mb/s. The modulations include quadrature phaseshift keying (QPSK), offset quadrature phase-shift keying (OQPSK), Gaussian minimum-shift keying (GMSK), and octonary phase-shift keying (8PSK) with square-root raised-cosine pulse shaping. The figure is a greatly simplified block diagram showing the relationship between the modulator board and the rest of the transmitter. The role of the modulator board is to encode the incoming data stream and to shape the resulting pulses, which are fed as inputs to the vector modulator. The combination of encoding and pulse shaping in a given application is chosen to maximize the bandwidth efficiency. The modulator board includes gallium arsenide serial-to-parallel converters at its input end. A complementary metal oxide/semiconductor (CMOS) field-programmable gate array (FPGA) performs the coding and modulation computations and utilizes parallel processing in doing so. The results of the parallel computation are combined and converted to pulse waveforms by use of gallium arsenide parallel-to-serial converters integrated with digital-to-analog converters. Without changing the hardware, one can configure the modulator to produce any of the designed combinations of coding and modulation by loading the appropriate bit configuration file into the FPGA.

Gray, Andrew↗

NASA NTRS1982

A jet controlled magnetic referenced attitude control system for spinning payloads

An attitude control system was designed permitting large angle acquisition and alignment of the principle axis of a spinning payload to within 1 degree of the earth's magnetic field. Signals from magnetometer and gyro sensors are fed to the control algorithm to generate commands for the jet thrusters. The algorithm contains a cross axis magnetometer signal to prevent a large angle magnetometer signal to prevent a large angle equilibrium solution. The acquisition will occur within 50 seconds from initial precession and nutation angles of 30 degrees. An electronic spin filter passes signals at spin and nutation frequencies and rejects bias signals due to sensor misalignment and principle axis offset. Describing function analysis and total analog simulation techniques were used. The flight ACS hardware was interfaced with the analog computer simulation for design and verification. The controller has flown on four successful missions.

Celmer, J. J.↗

NASA NTRS2008

Fast Offset Laser Phase-Locking System

Figure 1 shows a simplified block diagram of an improved optoelectronic system for locking the phase of one laser to that of another laser with an adjustable offset frequency specified by the user. In comparison with prior systems, this system exhibits higher performance (including higher stability) and is much easier to use. The system is based on a field-programmable gate array (FPGA) and operates almost entirely digitally; hence, it is easily adaptable to many different systems. The system achieves phase stability of less than a microcycle. It was developed to satisfy the phase-stability requirement for a planned spaceborne gravitational-wave-detecting heterodyne laser interferometer (LISA). The system has potential terrestrial utility in communications, lidar, and other applications. The present system includes a fast phasemeter that is a companion to the microcycle-accurate one described in High-Accuracy, High-Dynamic-Range Phase-Measurement System (NPO-41927), NASA Tech Briefs, Vol. 31, No. 6 (June 2007), page 22. In the present system (as in the previously reported one), beams from the two lasers (here denoted the master and slave lasers) interfere on a photodiode. The heterodyne photodiode output is digitized and fed to the fast phasemeter, which produces suitably conditioned, low-latency analog control signals which lock the phase of the slave laser to that of the master laser. These control signals are used to drive a thermal and a piezoelectric transducer that adjust the frequency and phase of the slave-laser output. The output of the photodiode is a heterodyne signal at the difference between the frequencies of the two lasers. (The difference is currently required to be less than 20 MHz due to the Nyquist limit of the current sampling rate. We foresee few problems in doubling this limit using current equipment.) Within the phasemeter, the photodiode-output signal is digitized to 15 bits at a sampling frequency of 40 MHz by use of the same analog-to-digital converter (ADC) as that of the previously reported phasemeter. The ADC output is passed to the FPGA, wherein the signal is demodulated using a digitally generated oscillator signal at the offset locking frequency specified by the user. The demodulated signal is low-pass filtered, decimated to a sample rate of 1 MHz, then filtered again. The decimated and filtered signal is converted to an analog output by a 1 MHz, 16-bit digital-to-analog converters. After a simple low-pass filter, these analog signals drive the thermal and piezoelectric transducers of the laser.

Shaddock, Daniel↗

NASA NTRS2016

Development of a High Performance, Low Profile Translation Table with Wire Feedthrough for a Deep Space CubeSat

NEAScout, a 6U cubesat and secondary payload on NASA's EM-1, will use an 85 sq m solar sail to travel to a near-earth asteroid at about 1 Astronomical Unit (about 1.5 x 10(exp 8) km) for observation and reconnaissance1. A combination of reaction wheels, reaction control system, and a slow rotisserie roll about the solar sail's normal axis were expected to handle attitude control and adjust for imperfections in the deployed sail during the 2.5-year mission. As the design for NEAScout matured, one of the critical design parameters, the offset in the center of mass and center of pressure (CP/CM offset), proved to be sub-optimal. After significant mission and control analysis, the CP/CM offset was accommodated by the addition of a new subsystem to NEAScout. This system, called the Active Mass Translator (AMT), would reside near the geometric center of NEAScout and adjust the CM by moving one portion of the flight system relative to the other. The AMT was given limited design space - 17 mm of the vehicle's assembly height-and was required to generate +/-8 cm by +/-2 cm translation to sub-millimeter accuracy. Furthermore, the design must accommodate a large wire bundle of small gage, single strand wire and coax cables fed through the center of the mechanism. The bend radius, bend resistance, and the exposure to deep space environment complicates the AMT design and operation and necessitated a unique design to mitigate risks of wire bundle damage, binding, and cold-welding during operation. This paper will outline the design constraints for the AMT, discuss the methods and reasoning for design, and identify the lessons learned through the designing, breadboarding and testing for the low-profile translation stages with wire feedthrough capability.

Few, Alex↗

NASA NTRS2016

Development of a High-Performance, Low-Profile Translation Table with Wire Feedthrough for a Deep Space CubeSat

NEAScout, a 6U cubesat and secondary payload on NASA's EM-1, will use an 85 sq m solar sail to travel to a near-earth asteroid at about 1 Astronomical Unit (about 1.5 x 10(exp 8) km) for observation and reconnaissance1. A combination of reaction wheels, reaction control system, and a slow rotisserie roll about the solar sail's normal axis were expected to handle attitude control and adjust for imperfections in the deployed sail during the 2.5-year mission. As the design for NEAScout matured, one of the critical design parameters, the offset in the center of mass and center of pressure (CP/CM offset), proved to be sub-optimal. After significant mission and control analysis, the CP/CM offset was accommodated by the addition of a new subsystem to NEAScout. This system, called the Active Mass Translator (AMT), would reside near the geometric center of NEAScout and adjust the CM by moving one portion of the flight system relative to the other. The AMT was given limited design space - 17 mm of the vehicle's assembly height-and was required to generate +/-8 cm by +/-2 cm translation to sub-millimeter accuracy. Furthermore, the design must accommodate a large wire bundle of small gage, single strand wire and coax cables fed through the center of the mechanism. The bend radius, bend resistance, and the exposure to deep space environment complicates the AMT design and operation and necessitated a unique design to mitigate risks of wire bundle damage, binding, and cold-welding during operation. This paper will outline the design constraints for the AMT, discuss the methods and reasoning for design, and identify the lessons learned through the designing, breadboarding and testing for the low-profile translation stages with wire feedthrough capability.

Few, Alex↗