Search NASA⌕ Search

SEARCH · Search NASA

Results for “oil separation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Transonic Navier-Stokes wing solutions using a zonal approach. Part 2: High angle-of-attack simulation

A computer code is under development whereby the thin-layer Reynolds-averaged Navier-Stokes equations are to be applied to realistic fighter aircraft configurations. This transonic Navier-Stokes code (TNS) utilizes a zonal approach in order to treat complex geometries and satisfy in-core computer memory constraints. The zonal approach was applied to isolated wing geometries in order to facilitate code development. The TNS finite difference algorithm, zonal methodology, and code validation with experimental data is addressed. Also addressed are some numerical issues such as code robustness, efficiency, and accuracy at high angles of attack. Special free-stream-preserving metrics proved an effective way to treat H-mesh singularities over a large range of severe flow conditions, including strong leading edge flow gradients, massive shock induced separation, and stall. Furthermore, lift and drag coefficients were computed for a wing up through CLmax. Numerical oil flow patterns and particle trajectories are presented both for subcritical and transonic flow. These flow simulations are rich with complex separated flow physics and demonstrate the efficiency and robustness of the zonal approach.

Chaderjian, Neal M.↗
NASA NTRS2009

Use of UV Sources for Detection and Identification of Explosives

Measurement of Raman and native fluorescence emission using ultraviolet (UV) sources (<400 nm) on targeted materials is suitable for both sensitive detection and accurate identification of explosive materials. When the UV emission data are analyzed using a combination of Principal Component Analysis (PCA) and cluster analysis, chemicals and biological samples can be differentiated based on the geometric arrangement of molecules, the number of repeating aromatic rings, associated functional groups (nitrogen, sulfur, hydroxyl, and methyl), microbial life cycles (spores vs. vegetative cells), and the number of conjugated bonds. Explosive materials can be separated from one another as well as from a range of possible background materials, which includes microbes, car doors, motor oil, and fingerprints on car doors, etc. Many explosives are comprised of similar atomic constituents found in potential background samples such as fingerprint oils/skin, motor oil, and soil. This technique is sensitive to chemical bonds between the elements that lead to the discriminating separability between backgrounds and explosive materials.

Hug, William↗
NASA NTRSDate not supplied

High-Lift Common Research Model: RANS, HRLES and WMLES Perspectives for CLmax Prediction Using LAVA

A unified assessment of three turbulence treatments: Reynolds Averaged Navier-Stokes(RANS), Hybrid RANS/LES (HRLES) and Equilibrium Wall-Modelled Large Eddy Simulation(WMLES) is presented for the High-Lift Common Research Model (CRM-HL). For the free-air configuration, steady-state RANS simulations show very accurate drag polar predictions in the low-𝛼linear regime. However, strong grid sensitivity is reported near the maximum lift-state(𝐶𝐿max), with finer-grids showing larger errors and predicting erroneous flow topologies on the wing. Our RANS simulations show that several corrections for the Spalart-Allmaras (SA)turbulence model widely used in the community lead to more erroneous results compared to the baseline closure, without exception. Both scale-resolving methods (HRLES and WMLES)address these drawbacks and predict an outboard separation pattern on the main element that is in good agreement with the oil flow photographs taken from the QinetiQ wind tunnel experiments, when LES-appropriate grids and numerical discretizations are used. While RANS simulations with the baseline SA closure do not show any wing-root separation post𝐶𝐿max, both HRLES and WMLES show onset of corner flow separation with varying degrees of progression, along with a weak pitch break in the wing-contribution of the overall pitching moment. This post-𝐶𝐿max pitch break seen in the free-air simulations is weaker than the break observed in experiments, with a weaker break reported in WMLES for each iteration of grid-refinement. In-tunnel simulations using both SA-baseline RANS and WMLES show a much stronger post-𝐶𝐿max break with the WMLES predictions showing excellent agreement with the experiment in terms of both the flow-topology observed and the pressure-coefficients at various spanwise stations. Sensitivity to the tunnel wall boundary layer is characterized via comparisons between viscous and inviscid treatments for the tunnel walls. WMLES predictions show moderate sensitivity at the predicted inboard flow-state at 𝐶𝐿max along with the progression towards a post-𝐶𝐿max stall; however, this stalled state at 𝛼≈20◦(inside the tunnel) obtained with both tunnel wall treatments appears to be largely identical.

TTT↗
NASA NTRS2023

Turbulence Model Validation Through Joint Experimental /Computational Studies of Separated Flow Over A Three-Dimensional Tapered Bump: Part I - Experimental Investigation

The results of a three-year experimental campaign aimed at comprehensively documenting the separated flow over a three-dimensional bump are presented with the purpose of generating a benchmark experimental database useful in validating computational fluid dynamics (CFD) flow simulations. The bump model geometry was designed to provide well-defined and repeatable smooth-body flow separation conditions that were suitable for both experiments and simulations. The bump had a Gaussian streamwise profile with a constant height equal to 8.5% of its width over the central 60% of the test section width. The remaining 40% were outboard spanwise portions that gradually taper to zero using an error function profile to minimize side-wall boundary layer effects. The model was immersed in a turbulent boundary layer that was developed on a suspended flat plate in the Notre Dame Mach 0.6 Wind Tunnel. In order to document the effect of the incoming boundary layer thickness on the flow separation, the bump model could be located at two streamwise positions. The mean velocity and turbulence intensity of the wind tunnel freestream flow field and approaching turbulent boundary layer were fully documented. The measurements of the flow separation region included surface visualization, wall shear stress using oil-film interferometry, mean and dynamic surface pressure, and planar and stereoscopic particle image velocimetry. The experiments were conducted over a range of Mach numbers from 0.05 to 0.2 corresponding to a range of Reynolds numbers based on the test section spanwise dimension (0.914m) of 1.0 × 10 6 ≤ Re L = U ∞ L/ν ≤ 4.0 × 10 6 . The bulk of the results are presented for the higher Mach number conditions of 0.1 and 0.2 with Re L = 2.0 × 10 6 and 4.0 × 10 6 , respectively. Extensive uncertainty analysis of the data was performed. The data is archived in the NASA Langley Turbulence Modeling Resource website at https://turbmodels.larc.nasa.gov/Other_exp_Data/speedbump_sep_exp.html. In addition to the experiments, a computational effort was made in parallel by the CFD group at Boeing Research & Technology highlighting the usefulness of the data set, which is outlined in the accompanying CFD report.

Flow separation↗
NASA NTRS1986

Transonic Navier-Stokes wing solutions using a zonal approach. Part 2: High angle-of-attack simulation

A computer code is under development whereby the thin-layer Reynolds-averaged Navier-Stokes equations are to be applied to realistic fighter-aircraft configurations. This transonic Navier-Stokes code (TNS) utilizes a zonal approach in order to treat complex geometries and satisfy in-core computer memory constraints. The zonal approach has been applied to isolated wing geometries in order to facilitate code development. Part 1 of this paper addresses the TNS finite-difference algorithm, zonal methodology, and code validation with experimental data. Part 2 of this paper addresses some numerical issues such as code robustness, efficiency, and accuracy at high angles of attack. Special free-stream-preserving metrics proved an effective way to treat H-mesh singularities over a large range of severe flow conditions, including strong leading-edge flow gradients, massive shock-induced separation, and stall. Furthermore, lift and drag coefficients have been computed for a wing up through CLmax. Numerical oil flow patterns and particle trajectories are presented both for subcritical and transonic flow. These flow simulations are rich with complex separated flow physics and demonstrate the efficiency and robustness of the zonal approach.

Chaderjian, N. M.↗
NASA NTRS1991

Aerodynamic measurements on a finite wing with simulated ice

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional straight and swept wing is studied experimentally. A semispan wing of effective aspect ratio five was mounted from the sidewall of the UIUC subsonic wind tunnel. The model uses an NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root sections to allow for 0- and 30-deg sweep. A sidewall suction system is used to minimize the tunnel boundary-layer interaction with the model. A three-component sidewall balance has been designed, built and used to measure lift, drag and pitching moment on the clean and iced model. Fluorescent oil flow visualization has been performed on the iced model and reveals extensive spanwise flow in the separation bubble aft of the upper surface horn. These results are compared to computational results for the surface pressures, span loads and surface oil flow.

Bragg, M. B.↗
NASA NTRS1988

A flow visualization study of the leading edge separation bubble on a NACA 0012 airfoil with simulated glaze ice

As a part of an ongoing research in aircraft icing, the leading edge separation bubble on a NACA 0012 model with a 5 min simulated glaze ice was investigated. The flow visualization methods using oil, tuft, splitter plate, smoke, and liquid crystals were employed to get reattachment line data for the leading edge separation bubble on both surfaces of the airfoil. On the upper surface, the separation bubble was found to grow larger with increasing angles of attack and reduce in size with decreasing angle of attack. On the lower surface, the bubble was found to grow larger with increasing negative angles of attack and reduce in size with increasing angles of attack. The separated flow fails to reattach beyond 6° for the upper surface and -5° for the loser surface. Their results of this study compared well with those of other experiments and computational results.

Aircraft icing↗
NASA NTRS1977

Infrared temperature maps of EHD lubrication

Technique uses an infrared detector with two specially selected infrared filters, in separately mapping the contact-surface temperature and average oil-film temperature in an elastohydrodynamic conjunction. Apparatus includes conventional four-ball bearing tester and temperature controlled lubricant system.

Sanborn, D. M.↗
NASA NTRS1985

Flow control in a diffusing S-Duct

Accurate measurements have been made of secondary flow in a 1.51 area ratio diffusing 30 deg - 30 deg S-Duct with circulair cross section. Turbulent flow was entering the duct at Mach number of 0.6, the boundary layer thickness at the duct entrance was ten percent of the duct inlet diameter. Through measurements made, local flow velocity vector as well as static and total pressures mapping of the flow at several stations were obtained. Strong secondary flow was measured in the first bend which continued into the second bend with new vorticity produced in there in the opposite direction. Surface oil flow visualization and wall pressures indicated a region of separated flow starting at theta approximately equal to 22 deg on the inside of the first bend up to theta approximately equal to 44 deg on the outside of the second bend. The flow separated in 'cyclone' form and never reattached in the duct. As a result of the secondary flow and the flow separation, significant total pressure distortion was observed at the exit of the duct. Using flow control devices the separation was eliminated while the exit distortion was improved.

Vakili, A. D.↗
NASA NTRS1979

A visual investigation of the separation and subsequent transition near the leading edge of airfoils

Subsonic (5 to 30 m/sec) wind tunnels were used to measure pressure distributions at the leading edge and upper surface of airfoil models and to obtain high-speed movie photographs of smoke-visualized separation, transition, and reattachment phenomena. Points of turbulent shear layer reattachment could be determined by using an oil-mixture coating on the surface. Plots of the static pressure coefficient along the chord of several models are presented, and the measured separation, transition, and reattachment points are plotted against the chord Reynolds number.

Arena, A. V.↗
NASA NTRS1978

Visualization of the separation and subsequent transition near the leading edge of airfoils

A visual study was performed using the low speed smoke wind tunnels with the objective of obtaining a better understanding of the structure of leading edge separation bubbles on airfoils. The location of separation, transition and reattachment for a cylindrical nose constant-thickness airfoil model were obtained from smoke photographs and surface oil flow techniques. These data, together with static pressure distributions along the leading edge and upper surface of the model, produced the influence of Reynolds number, angle of attack, and trailing edge flap angle on the size and characteristics of the bubble. Additional visual insight into the unsteady nature of the separation bubble was provided by high speed 16 mm movies. The 8 mm color movies taken of the surface oil flow supported the findings of the high speed movies and clearly showed the formation of a scalloped spanwise separation line at the higher Reynolds number.

Arena, A. V.↗
NASA NTRS1991

Measurements of forces, moments, and pressures on a generic store separating from a box cavity at supersonic speeds

An experimental investigation was conducted to measure the forces, moments, and pressure distributions on the generic store separating from a rectangular box cavity contained in a flat plate surface at supersonic speeds. Pressure distributions inside the cavity and oil flow and vapor-screen photographs of the cavity flow field were also obtained. The measurements were obtained for the store separating from a flat plate surface, from two shallow cavities having length to depth ratios (L/h) of 16.778 and 12.073, and from a deep cavity having L/h = 6.730. Measurements for the shallow cavities were obtained both with and without rectangular doors attached to sides of the cavities. The tests were conducted at free stream Mach numbers of 1.69, 2.00 and 2.65 for a free stream Reynolds number per foot of 2 x 10(exp 6). Presented here are a discussion of the results, a complete tabulation of the pressure data, figures of both the pressure and force and moment data, and representative oil flow and vapor screen photographs.

Stallings, Robert L., Jr.↗
NASA NTRS1986

Flow-separation patterns on symmetric forebodies

Flow-visualization studies of ogival, parabolic, and conical forebodies were made in a comprehensive investigation of the various types of flow patterns. Schlieren, vapor-screen, oil-flow, and sublimation flow-visualization tests were conducted over an angle-of-attack range from 0 deg. to 88 deg., over a Reynolds-number range from 0.3X10(6) to 2.0X10(6) (based on base diameter), and over a Mach number range from 0.1 to 2. The principal effects of angle of attack, Reynolds number, and Mach number on the occurrence of vortices, the position of vortex shedding, the principal surface-flow-separation patterns, the magnitude of surface-flow angles, and the extent of laminar and turbulent flow for symmetric, asymmetric, and wake-like flow-separation regimes are presented. It was found that the two-dimensional cylinder analogy was helpful in a qualitative sense in analyzing both the surface-flow patterns and the external flow field. The oil-flow studies showed three types of primary separation patterns at the higher Reynolds numbers owing to the influence of boundary-layer transition. The effect of angle of attack and Reynolds number is to change the axial location of the onset and extent of the primary transitional and turbulent separation regions. Crossflow inflectional-instability vortices were observed on the windward surface at angles of attack from 5 deg. to 55 deg. Their effect is to promote early transition. At low angles of attack, near 10 deg., an unexpected laminar-separation bubble occurs over the forward half of the forebody. At high angles of attack, at which vortex asymmetry occurs, the results support the proposition that the principal cause of vortex asymmetry is the hydrodynamic instability of the inviscid flow field. On the other hand, boundary-layer asymmetries also occur, especially at transitional Reynolds numbers. The position of asymmetric vortex shedding moves forward with increasing angle of attack and with increasing Reynolds number, and moves rearward with increasing Mach number.

Keener, Earl R.↗
NASA NTRS1987

Experimental flowfield visualization of a high alpha wing at Mach 1.62

Experimental oil-flow and tuft patterns and vapor-screen flow-visualization data were obtained on a cambered wing model at Mach = 1.62 for an angle-of attack range of 0-14 deg. These data were used as flow diagnostic tools along with surface-pressure and force data and full-potential theory calculations. A large separation bubble was found on the lower wing surface at low angle of attack. The high-angle-of-attack flowfield was characterized by a large attached-flow leading-edge expansion followed by a crossflow shock. At alpha = 14 deg the crossflow shock apparently induced discrete regions of streamwise separated flow, which were clearly indicated in the vapor-screen and oil-flow photographs.

Pittman, James L.↗
NASA NTRS1987

Experimental flowfield visualization of a high alpha wing at Mach 1.62

Experimental oil-flow and tuft patterns and vapor-screen flow-visualization data were obtained on a cambered wing model at Mach 1.62 for an angle-of-attack range of 0 to 14 deg. These data were used as flow diagnostic tools along with surface-pressure and force data and full-potential theory calculations. A large separation bubble was found on the lower wing surface at low angle of attack. The high-angle-of-attack flowfield was characterized by a large attached-flow leading-edge expansion followed by a cross-flow shock. At 14 deg, the cross-flow shock apparently induced discrete regions of streamwise separated flow which were clearly indicated in the vapor-screen and oil-flow photographs.

Pittman, James L.↗
NASA NTRS2010

High-Speed PLIF Imaging of Hypersonic Transition over Discrete Cylindrical Roughness

In two separate test entries, advanced laser-based instrumentation has been developed and applied to visualize the hypersonic flow over cylindrical protrusions on a flat plate. Upstream of these trips, trace quantities of nitric oxide (NO) were seeded into the boundary layer. The protuberances were sized to force laminar-to-turbulent boundary layer transition. In the first test, a 10-Hz nitric oxide planar laser-induced fluorescence (NO PLIF) flow visualization system was used to provide wide-field-of-view, high-resolution images of the flowfield. The images had sub-microsecond time resolution. However these images, obtained with a time separation of 0.1 sec, were uncorrelated with each other. Fluorescent oil-flow visualizations were also obtained during this test. In the second experiment, a laser and camera system capable of acquiring NO PLIF measurements at 1 million frames per second (1 MHz) was used. This system had lower spatial resolution, and a smaller field of view, but the images were time correlated so that the development of the flow structures could be observed in time.

Danehy, P. M.↗
NASA NTRS2012

Experimental Investigation of Normal Shock Boundary-Layer Interaction with Hybrid Flow Control

Hybrid flow control, a combination of micro-ramps and micro-jets, was experimentally investigated in the 15x15 cm Supersonic Wind Tunnel (SWT) at the NASA Glenn Research Center. Full factorial, a design of experiments (DOE) method, was used to develop a test matrix with variables such as inter-ramp spacing, ramp height and chord length, and micro-jet injection flow ratio. A total of 17 configurations were tested with various parameters to meet the DOE criteria. In addition to boundary-layer measurements, oil flow visualization was used to qualitatively understand shock induced flow separation characteristics. The flow visualization showed the normal shock location, size of the separation, path of the downstream moving counter-rotating vortices, and corner flow effects. The results show that hybrid flow control demonstrates promise in reducing the size of shock boundary-layer interactions and resulting flow separation by means of energizing the boundary layer.

Vyas, Manan A.↗
NASA NTRS2001

An Experimental Study of the Ground Transportation System (GTS) Model in the NASA Ames 7- by 10-Ft Wind Tunnel

The 1/8-scale Ground Transportation System (GTS) model was studied experimentally in the NASA Ames 7- by 10-Ft Wind Tunnel. Designed for validation of computational fluid dynamics (CFD), the GTS model has a simplified geometry with a cab-over-engine design and no tractor-trailer gap. As a further simplification, all measurements of the GTS model were made without wheels. Aerodynamic boattail plates were also tested on the rear of the trailer to provide a simple geometry modification for computation. The experimental measurements include body-axis drag, surface pressures, surface hot-film anemometry, oil-film interferometry, and 3-D particle image velocimetry (PIV). The wind-averaged drag coefficient with and without boattail plates was 0.225 and 0.277, respectively. PIV measurements behind the model reveal a significant reduction in the wake size due to the flow turning provided by the boattail plates. Hot-film measurements on the side of the cab indicate laminar separation with turbulent reattachment within 0.08 trailer width for zero and +/- 10 degrees yaw. Oil film interferometry provided quantitative measurements of skin friction and qualitative oil flow images. A complete set of the experimental data and the surface definition of the model are included on a CD-ROM for further analysis and comparison.

Storms, Bruce L.↗