Search NASA⌕ Search

SEARCH · Search NASA

Results for “oscillatory power”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Flight investigation of stall, spin and recovery characteristics of a low-wing, single-engine, T-tail light airplane

Flight tests were performed to investigate the stall, spin, and recovery characteristics of a four-place, low-wing, single-engine, T-tail, general aviation research airplane at an aft center-of-gravity position. Most stalls resulted in roll-offs. Spins were oscillatory in roll and pitch at 43 deg angle of attack; the magnitude of the oscillations was determined by aileron position. Power, flap deflection, and landing gear position did not affect the angle of attack to the spin. Antispin rudder followed by forward wheel with ailerons neutral produced the fastest and most consistent recoveries but the initial application of recovery controls did not always stop a spin.

Stough, H. P., III↗
NASA NTRS1999

Phase-Shifted Laser Feedback Interferometry

Phase-shifted, laser feedback interferometry is a new diagnostic tool developed at the NASA Lewis Research Center under the Advanced Technology Development (ATD) Program directed by NASA Headquarters Microgravity Research Division. It combines the principles of phase-shifting interferometry (PSI) and laser-feedback interferometry (LFI) to produce an instrument that can quantify both optical path length changes and sample reflectivity variations. In a homogenous medium, the optical path length between two points is the product of the index of refraction and the geometric distance between the two points. LFI differs from other forms of interferometry by using the laser as both the source and the phase detector. In LFI, coherent feedback of the incident light either reflected directly from a surface or reflected after transmission through a region of interest will modulate the output intensity of the laser. The combination of PSI and LFI has produced a robust instrument, based on a low-power helium-neon (HeNe) gas laser, with a high dynamic range that can be used to measure either static or oscillatory changes of the optical path length. Small changes in optical path length are limited by the fraction of a fringe that can be measured; we can measure nonoscillatory changes with a root mean square (rms) error of the wavelength/1000 without averaging.

Ovryn, Benjie↗
NASA NTRS2003

Low Frequency High Amplitude Temperature Oscillations in Loop Heat Pipe Operation

This paper presents a theory that explains low frequency, high amplitude temperature oscillations in loop heat pipe (LHP) operation. Oscillations of the CC temperature with amplitudes on the order of tens of degrees Kelvin and periods on the order of hours have been observed in some LHPs during ambient testing. There are presently no satisfactory explanations for such a phenomenon in the literature. It is well-known that the operating temperature of an LHP with a single evaporator is governed by the compensation chamber (CC) temperature, which in turn is a function of the evaporator heat load, sink temperature, and ambient temperature. As the operating condition changes, the CC temperature will change during the transient but eventually reach a new steady temperature. Under certain conditions, however, the LHP never really reaches a true steady state, but instead displays an oscillatory behavior. The proposed new theory describes why low frequency, high amplitude oscillations may occur when the LHP has a low evaporator power, a low heat sink temperature (below ambient temperature), and a large thermal mass attached to the evaporator. When this condition prevails, there are some complex interactions between the CC, condenser, thermal mass and ambient. The temperature oscillation is a result of the large movement of the vapor front inside the condenser, which is caused by a change in the net evaporator power modulated by the large thermal mass through its interaction with the sink and CC. The theory agrees very well with previously published test data. Effects of various parameters on the amplitude and frequency of the temperature oscillation are also discussed.

Ku, Jentung↗
DOE OSTI2024

Inverter Intensive Hybrid Power Plant Modeling with Small-Signal Stability Augmentation through Flexible Operation Mode Transition

Hybrid power plants (HPPs) prompt the penetration of inverter-based renewable energy sources (RES) in transmission systems; however, given their low-inertia nature, HPPs are dominated by power electronic inverters, so there are inevitable challenges in system stability when increasing numbers of HPPs are integrated into the modern power grids. To boost the penetration level of HPPs without jeopardizing system stability, it is desirable to equip them with operational characteristics (i.e., grid-forming capabilities) that are comparable to those of conventional power plants dominated by synchronous generators (SGs). In this paper, a holistic model of inverter intensive HPP is derived and a bi-level hierarchical control is developed to allow HPPs to flexibly switch among the designed operation modes (i.e., P-Q, P-V, and isochronous modes). Compared to SGs, which have limited controllability, the operation mode of each HPP could vary as requested. Such flexible mode transitions could be integrated into the secondary plant-level control and be leveraged as an additional control degree to further augment system stability. Further, the system small-signal stability margin is quantified with varying HPP operation modes. More importantly, modal analysis is thereby conducted to quantify the impacts of mode transition on the system oscillatory modes. The effectiveness of the proposed HPP bi-level hierarchical control is verified using extensive case studies based on the simplified real-world island power grid, and the results validate that the system small-signal stability margin can be enhanced with the additional degree of control flexibility enabled by HPP operation mode transition. The real-time hardware-in-the-loop (HIL) results are also provided to verify the proposed method.

grid-forming control↗
NASA NTRS1957

Concluding Report of Free-Spinning, Tumbling, and Recovery Characteristics of a 1/18-Scale Model of the Ryan X-13 Airplane, Coord. No. AF-199

An investigation has been completed in the Langley 20-foot free-spinning tunnel on a l/18-scale model of the Ryan X-13 airplane to determine its spin, recovery, and tumbling characteristics, and to determine the minimum altitude from which a belly landing could be made in case of power failure in hovering flight. Model spin tests were conducted with and without simulated engine rotation. Tests without simulated engine rotation indicated two types of spins: one, a slightly oscillatory flat spin; and the other, a violently oscillatory spin. Tests with simulated engine rotation indicated that spins to the left were fast rotating and steep and those to the right were slow rotating and flat. The optimum technique for recovery is reversal of the rudder to against the spin and simultaneous movement of the ailerons to full with the spin followed by movement of the elevators to neutral after the spin rotation ceases. Tumbling tests made on the model indicated that although the Ryan X-13 airplane will not tumble in the ordinary sense (end-over-end pitching motion), it may instead tend to enter a wild gyrating'motion. Tests made to simulate power failure in hovering flight by dropping the model indicated that the model entered what appeared to be a right spin. An attempt should be made to stop this motion immediately by moving the rudder to oppose the rotation (left pedal), moving the ailerons to with the spin (stick right), and moving the stick forward after the spin rotation ceases to obtain flying speed for pullout. The minimum altitude required for a belly landing in case of power failure in hovering flight was indicated to be about 4,200 feet.

Bowman, James S., Jr.↗
DOE OSTI2025

Egg yolk as a model for gelation: From rheometry to flow physics

Egg yolks are an excellent model for studying sol-gel transitions, particularly the power law viscoelasticity that defines the critical point of gelation. However, prior studies lack comprehensive datasets and fail to visualize flow behavior linked to temperature and time-dependent linear and nonlinear rheology. Here, we present a detailed dataset characterizing egg yolk viscoelasticity across temperature, time, and forcing amplitude using oscillatory shear, step strain, step stress, and constant high strain rate. Novel protorheology visualizations link rheological properties with observable flow behavior. Our findings highlight the nuanced determination of the critical gel point, emphasizing observation timescale dependencies. We compare methods to identify critical temperatures for gelation, including power law viscoelasticity, moduli crossover, diverging zero-shear viscosity, and emerging equilibrium elastic modulus, while visualizing flow consequences near these transitions. Egg yolk is an accessible, realistic, and nontoxic material relevant to the physicist and the chef alike, making it ideal for understanding the rheology of critical gels. By integrating protorheology photos and videos with rigorous rheometric data, we deepen the understanding of critical gels, with broader impacts for studying other materials with sol-gel transitions.

Marsh, Maxwell C. [Department of Mechanical Scienc↗
DOE OSTI2024

Modeling the Impacts of Material Properties on Oscillatory Neuron Behavior

In this study, neuromorphic computing, which mimics the functions of biological brains, offers improvements in both latency and energy efficiency over typical von Neumann computing architectures. Spiking neural networks can be especially power-efficient because they encode information temporally and can use more sparse electrical inputs. Here, we study the design of volatile memristors (variable resistors with memory) for neuronal devices, with particular consideration toward the feasibility of all-on-chip oscillation using built-in capacitance. We use circuit simulations to model the behavior of oscillator neurons with a range of realistic material properties. We find that energy inputs increase with insulating-phase resistivity, thermal conductivity, and device aspect ratio. However, we also find that the minimum capacitance needed for oscillation decreases with increasing insulating-phase resistivity, which opposes the constraints for power efficiency. Based on published data on NbO 2 , VO 2 , and EuNiO 3 , we find that existing materials can be engineered for all-on-chip spiking using their parasitic capacitance.

36 MATERIALS SCIENCE↗
NASA NTRS1984

Electromagnetic damping of neutron star oscillations

A simple model of magnetic field perturbations driven by neutron star oscillations is used to estimate the electromagnetic power radiated by g-modes and torsional oscillations. The calculation assumes that the neutron star has a frozen-in magnetic field which is perturbed by the oscillatory motions of the surface. The disturbances propagate into the vacuum as outgoing electromagnetic waves. The relative effectiveness of Joule heating of the neutron star crust by pulsation-induced electric currents is estimated. It is concluded that electromagnetic damping is the dominant energy dissipation mechanism for quadrupole g-mode oscillations of neutron stars. For dipole spheroidal modes, both electromagnetic radiation and Joule heating are important, and there is no gravitational radiation emitted by these modes.

Mcdermott, P. N.↗
NASA NTRS1965

Operational Experiences of Turbine-Powered Commercial Transport Airplanes

Recent results obtained from NASA V-G and VGH recorders installed on commercial turbine-powered transports have indicated that exceedances of placard speeds appear to have been significantly reduced since the placard speeds have been redefined and changes made in the aural warning. Oscillatory accelerations and unusual events, such as large or rapid departures from the planned flight profile, occur less frequently. Landing-impact accelerations are higher for turbine transports than for piston transports and vary with operator. The total in-flight acceleration experiences for turbine transports, however, are not significantly different from those for four-engine piston transports.

Hunter, Paul A.↗
NASA NTRS1977

Optimal low-thrust takeoff from an orbit about an oblate planet

Future space missions to the outer planets may depend upon the use of low-thrust propulsion systems. As these planets are decidedly oblate, the question of the effect of that oblateness on a low-thrust trajectory is of some interest. In this paper the problem of optimal energy increase is attacked under the assumption that the coefficients for the second zonal harmonic, and the nondimensional thrust acceleration are the same order of magnitude. By means of a two-variable asymptotic expansion technique, a near optimal control program is generated and the first-order uniformly valid approximation for the corresponding trajectory is obtained. Tangential thrust is shown to be a good near-optimal thrust program even in the presence of oblateness effects. The optimal control program is found to be oscillatory and quite similar to the optimal control for energy increase in an inverse square gravitational field.

Jacobson, R. A.↗
NASA NTRS2006

Thrust Stand for Electric Propulsion Performance Evaluation

An electric propulsion thrust stand capable of supporting testing of thrusters having a total mass of up to 125 kg and producing thrust levels between 100 microN to 1 N has been developed and tested. The design features a conventional hanging pendulum arm attached to a balance mechanism that converts horizontal deflections produced by the operating thruster into amplified vertical motion of a secondary arm. The level of amplification is changed through adjustment of the location of one of the pivot points linking the system. Response of the system depends on the relative magnitudes of the restoring moments applied by the displaced thruster mass and the twisting torsional pivots connecting the members of the balance mechanism. Displacement is measured using a non-contact, optical linear gap displacement transducer and balance oscillatory motion is attenuated using a passive, eddy-current damper. The thrust stand employs an automated leveling and thermal control system. Pools of liquid gallium are used to deliver power to the thruster without using solid wire connections, which can exert undesirable time-varying forces on the balance. These systems serve to eliminate sources of zero-drift that can occur as the stand thermally or mechanically shifts during the course of an experiment. An in-situ calibration rig allows for steady-state calibration before, during and after thruster operation. Thrust measurements were carried out on a cylindrical Hall thruster that produces mN-level thrust. The measurements were very repeatable, producing results that compare favorably with previously published performance data, but with considerably smaller uncertainty.

Polzin, Kurt A.↗
NASA NTRS1998

Oscillatory/Chaotic Thermocapillary Flow Induced by Radiant Heating

There is a continuing need to understand the fluid physics occurring under low gravity conditions in processes such as crystal growth, materials processing, and the movement of bubbles or droplets. The fluid flow in such situations is often caused by a gradient in interfacial tension. If a temperature gradient is created due to a heat source, the resulting flow is called thermocapillary flow, a special case of Marangoni Convection. In this study, an experimental investigation was conducted using silicone oil in cylindrical containers with a laser heat source at the free surface. It was desired to determine the conditions under which steady, axisymmetrical thermocapillary flow becomes unstable and oscillatory three-dimensional flow states develop. The critical Marangoni number for each observed oscillatory state was measured as a function of the container aspect ratio and the dynamic Bond number, a measure of buoyant force versus ii thermocapillary force. Various oscillatory modes were observed during three- dimensional convection, and chaotic flow was reached in one test condition. The critical Marangoni numbers are compared with those measured in previous studies, and the power spectra and phase trajectories of the instantaneous surface temperature distributions are used to characterize the routes of transitions to the chaotic flow state. Results show that only superharmonic modes appear in the routes to chaos while infinite number of subharmonic modes occur in flow transitions for pure Rayleigh convection.

DeWitt, Kenneth J.↗
DOE OSTI2025

Investigation of magnetic fluctuations in L-H and H-L transition dynamics on DIII-D

The dynamics of the L-H transition is not fully understood, with many parameters changing the threshold power to enter H-mode and the self-regulation between zonal flows and turbulence in the plasma edge. This paper is primarily a presentation of experimental results for DIII-D L-H and H-L transitions and speculation on the observations made. Power threshold analysis and measurements of pedestal temperatures for these transitions are presented. A comparison is made between an L-H transition and H-L transition of comparable Psep exhibiting oscillatory behaviour, showing symmetry between forward and backward transition dynamics. This paper shows the first observations of magnetic fluctuations during L-H and H-L transitions on DIII-D, and shows that L-H and H-L transitions have similar magnetic fluctuation dynamics. Information geometry analysis has been performed on measurements of plasma density fluctuations, perpendicular plasma velocity fluctuations, and magnetic field fluctuations to investigate the self-regulation and evolution of these variables during the transitions. Perpendicular flow evolution is shown to dominate the transition dynamics in both directions, but self-regulation behaviour is observed between all three variables. A strong correlation between magnetic fluctuation information rate and density fluctuation information rate for these two shots shows the strong influence of magnetic behaviour on both the L-H and H-L transition, and that these transition dynamics necessarily include electromagnetic effects.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS2003

High Frequency Low Amplitude Temperature Oscillations in Loop Heat Pipe Operation

The operating temperature of a loop heat pipe (LHP) with a single evaporator is governed by the compensation chamber (CC) temperature, which in turn is a finction of the evaporator power, condenser sink temperature, and ambient temperature. As the operating condition changes, the CC temperature will change during the transient but eventually reach a new steady temperature. Under certain conditions, however, the LHP never really reaches a true steady state, but instead displays an oscillatory behavior. This paper presents a study on the oscillation of the loop operating temperature with amplitudes on the order of one degree Kelvin and frequencies on the order of 10(exp -1) to 10(exp -2) Hertz. The source of the high frequency temperature oscillation is the fast movement of the vapor front in the condenser section, which usually occurs when the vapor front is near the condenser inlet or the condenser outlet. At these locations, the vapor front is unable to find a stable position for the given operating conditions, and will move back and forth. The movement of the vapor front causes the movement of the liquid in the condenser and the liquid line, leading to oscillations of the CC and the loop temperatures. Factors that affect the vapor front movement include evaporator power, condenser sink temperature, body forces and whether or the CC temperature is actively controlled. As long as there are no large thermal masses attached to the evaporator, the loop can self adjust rather quickly and the vapor front will move rapidly around the condenser inlet or outlet, leading to high frequency temperature oscillations. The amplitude of temperature oscillation is usually the largest in the liquid line, up to 20 degrees Kelvin in many cases, but diminishes to less than one degree Kelvin in the CC. Furthermore, the high frequency temperature oscillation can occur at any CC temperature when the right combination of the evaporator power and condenser sink temperature prevails.

Ku, Jentung↗
DOE OSTI2022

A unique gravitational wave signal from phase transition during inflation

We study the properties of the gravitational wave (GW) signals produced by first-order phase transitions during the inflation era. We show that the power spectrum of the GW oscillates with its wave number. This signal can be observed directly by future terrestrial and spatial gravitational wave detectors and through the B-mode spectrum in CMB. This oscillatory feature of GW is generic for any approximately instantaneous sources occurring during inflation and is distinct from the GW from phase transitions after the inflation. The details of the GW spectrum contain information about the scale of the phase transition and the later evolution of the universe.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS1983

Analysis of oscillatory motion of a light airplane at high values of lift coefficient

A modified stepwise regression is applied to flight data from a light research air-plane operating at high angles at attack. The well-known phenomenon referred to as buckling or porpoising is analyzed and modeled using both power series and spline expansions of the aerodynamic force and moment coefficients associated with the longitudinal equations of motion.

Batterson, J. G.↗
NASA NTRS2004

Oscillatory Hierarchy Controlling Cortical Excitability and Stimulus Integration

Cortical gamma band oscillations have been recorded in sensory cortices of cats and monkeys, and are thought to aid in perceptual binding. Gamma activity has also been recorded in the rat hippocampus and entorhinal cortex, where it has been shown, that field gamma power is modulated at theta frequency. Since the power of gamma activity in the sensory cortices is not constant (gamma-bursts). we decided to examine the relationship between gamma power and the phase of low frequency oscillation in the auditory cortex of the awake macaque. Macaque monkeys were surgically prepared for chronic awake electrophysiological recording. During the time of the experiments. linear array multielectrodes were inserted in area AI to obtain laminar current source density (CSD) and multiunit activity profiles. Instantaneous theta and gamma power and phase was extracted by applying the Morlet wavelet transformation to the CSD. Gamma power was averaged for every 1 degree of low frequency oscillations to calculate power-phase relation. Both gamma and theta-delta power are largest in the supragranular layers. Power modulation of gamma activity is phase locked to spontaneous, as well as stimulus-related local theta and delta field oscillations. Our analysis also revealed that the power of theta oscillations is always largest at a certain phase of delta oscillation. Auditory stimuli produce evoked responses in the theta band (Le., there is pre- to post-stimulus addition of theta power), but there is also indication that stimuli may cause partial phase re-setting of spontaneous delta (and thus also theta and gamma) oscillations. We also show that spontaneous oscillations might play a role in the processing of incoming sensory signals by 'preparing' the cortex.

Shah, A. S.↗