Search NASA⌕ Search

SEARCH · Search NASA

Results for “oxidation kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

A new approach to the oxidational theory of mild wear

The wear and friction of 316 stainless steel was investigated in relation to oxidation at the real area of contact. An approach describing the oxidation characteristics of mild wear in terms of linear oxidation kinetics is presented. Linear oxidation kinetics more closely approaches the physical conditions involved where oxide growth on asperities is continuously interrupted by spalling and removal. The mild wear rate may now be described mathematically by two empirical equations in terms of the operational variables and the oxidational constants without using the critical oxide thickness, which is dependent on asperity size, shape and temperature, and is difficult to measure. The resulting activation energy for oxidational wear was significantly lower than that for static oxidation governed by diffusion controlled kinetics.

Hong, H.↗
DOE OSTI2026

Intrinsic kinetics of water-inhibited ultra-lean methane oxidation over PtPd-Mg/ θ -Al 2 O 3 catalyst

Here, this study develops intrinsic methane oxidation kinetics for ultra-lean methane conditions in the presence of water over a highly active and stable PtPd–Mg/θ-Al 2 O 3 catalyst. Comprehensive laboratory experiments were conducted over a wide range of methane concentrations (150–1200 ppm CH 4 ), water contents (1–5% H 2 O), and industrially relevant space velocities (80,000 ≤ GHSV ≤ 160,000 h -1 ). These systematic experiments informed a two-dimensional, axisymmetric, multiscale reactor model that was used to develop and validate methane oxidation kinetics under practically relevant conditions, including non-isothermal operation and high conversion regimes. Combined experimental and modeling results revealed significant intraparticle diffusion resistance and transport-induced reaction exotherm at elevated temperatures, which limited catalyst utilization despite high intrinsic activity. These transport effects were explicitly incorporated into the reactor model, enabling accurate estimation of intrinsic kinetic parameters without reliance on conventional effectiveness-factor corrections. The resulting kinetic model successfully captured both kinetically controlled and mass-transfer-limited regimes and reliably predicted CH 4 conversion across broad ranges of temperature, methane concentration, and water content

Heat and mass transfer limitations↗
DOE OSTI2025

Study on ammonia and dimethyl ether oxidation and kinetic interaction up to 100 atm

NH 3 and DME dual fuel oxidation and kinetic coupling are experimentally studied by using a supercritical pressure jet-stirred reactor (SP-JSR) at 20 and 100 atm, over a temperature range of 500–900 K, and at fuel-lean and stoichiometric conditions with NH 3 to DME molar ratios of 4 and 0.62, respectively. An HP-Mech model for high-pressure NH3/DME oxidation is developed based on our previous studies and it shows generally better performance than other models in the literature on high-pressure oxidation experiments. Due to DME’s strong low-temperature reactivity, it dramatically enhances the oxidation of NH3 at low temperature. However, the effect of NH 3 on DME oxidation varies with temperature. At low temperatures, NH 3 inhibits low-temperature reactivity by consuming OH radicals. In addition, the NH 2 and NO x formation from NH 3 further suppresses the low-temperature DME reactivity by reducing alkylperoxyl and O 2 QOOH radicals via RO 2 + NH 2 = RO + H 2 NO, RO 2 + NO = RO + NO 2 and O 2 QOOH + NO = 2CH 2 O + HO 2 + NO 2 . At intermediate temperatures, due to enhanced kinetic coupling of NH 2 /NO x /HO 2 chemistry, DME oxidation is significantly promoted. It is found that there are two major NH 2 /NO x /HO 2 coupling pathways for OH radical production brought by NH 3 : (1) NH 2 + HO 2 = H 2 NO + OH and (2) NH 2 + NO 2 = H 2 NO + NO with NO + HO 2 = OH + NO 2 . Moreover, the resulting H 2 NO will further contribute to OH production via the H 2 NO/NO x /HONO coupling pathways: H 2 NO + NO 2 = HNO + HONO, HNO + NO 2 = HONO + NO, and HONO (+M) = OH + NO (+M). These new NH 2 /NO x /HO 2 and H 2 NO/NO x /HONO pathways play a critical role in promoting DME oxidation at intermediate temperatures. Novelty and Significance Statement: Blending NH 3 with DME can significantly enhance the reactivity of NH 3 and facilitate its practical application in advanced internal combustion engines. NH 3 /DME oxidation is studied in a novel supercritical pressure jet-stirred reactor up to 100 atm, a much higher pressure than previous studies. An interesting non-monotonic effect of NH3 addition on fuel oxidation has been found. Unique kinetic couplings of NH2/HO2/NOx and H2NO/NOx/HONO brough by NH3 and DME blending are identified to play important roles in radical generation and reactivity promotion. The valuable experimental data and key kinetics revealed in the current work can tremendously improve our understanding of NH 3 /DME oxidation via NO x /RO 2 and NH 2 / H 2 NO/HO 2 /NO x kinetic couplings at low to intermediate temperatures.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Microstructural, Oxidation, and Mechanical Behavior of NbTi-Based Refractory Alloys with 5 to 10 Pct Co, Cr, and Ni Additions

NbTi-based refractory alloys with additions of Co, Cr, and Ni represent an interesting medium-entropy alloy system with potential for protective oxide film formation, high strength, and ductility. This study investigates the microstructural evolution, oxidation behavior, and mechanical properties of NbTi-based alloys containing 5 to 10 at. pct Co, Cr, and Ni. CALPHAD predictions suggest that this composition range can be heat treated to obtain a predominantly body-centered cubic matrix phase. Mechanical properties, including microhardness, yield strength, maximum strength, and specific strength are evaluated through isothermal compression tests conducted between room temperature and 800 °C. The oxidation kinetics of these alloys are assessed through discontinuous oxidation tests. Parabolic oxidation kinetics were observed for NbTi–10Ni and NbTi–5Co, while linear oxidation kinetics were found for NbTi–10Cr and NbTi–10(CoCrNi). Microstructures and oxide layers are characterized using X-ray diffraction, electron backscatter diffraction, energy-dispersive X-ray spectroscopy, and scanning electron microscopy. All alloys exhibit significant mechanical softening between room temperature and 800 °C, with elastic-perfectly plastic flow observed at 800 °C. The addition of 10 pct Cr to NbTi resulted in two BCC phases up to 1050 °C, conflicting with CALPHAD predictions of a single-phase solid solution at this temperature, and resulting in higher flow stress at 800 °C. NbTi–10(CoCrNi) exhibited the lowest flow stress at 800 °C despite having more ‘cocktail effect’ potential and insufficient molar fractions of Co, Cr, or Ni to form a desirable protective oxide film.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Kinetic Probes of the Origin of Activity in MOF-Based C–H Oxidation Catalysis

The development of homogeneous catalysis is enabled by the availability of a rich toolkit of kinetics experiments, such as the Hgdrop test, that differentiate catalytic activity at ligand-supported metal complexes from potential heterogeneous catalysts derived from decomposition of molecular species. Metal-organic frameworks (MOFs) have garnered significant attention as platforms for catalysis at site-isolated, interstitial catalyst sites. Unlike homogeneous catalysis, relatively few strategies have been advanced to evaluate the origin of catalytic activity in MOF-promoted reactions. Many of the MOFs that have been examined as potential catalysts are comprised of molecular constituents that represent viable catalysts in the absence of the extended MOF lattice, and thus interfacial sites and leached homogeneous species represent potential sources of catalyst activity. Here, we demonstrate that analysis of deuterium kinetic isotope effects (KIEs) and olefin epoxidation diastereoselectivity provides probes of the origin of catalytic activity in MOF-promoted oxidation reactions. These analyses support involvement of lattice-based Fe sites in the turnover-limiting step of C–H activation with Fe-MOF-74-based materials (i.e., the MOF functions as a bona fide catalyst) and evidence that Cu 2 -based MOF MIL-125-Cu 2 O 2 functions as a solid-state initiator for solution-phase oxidation chemistry and is not involved in the turnover limiting step (i.e., the MOF does not function as a catalyst for substrate functionalization). furthermore, we anticipate that the simple experiments described here will provide a valuable tool for clarifying the role of MOFs in C–H oxidation reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1988

Fundamental kinetics and mechanistic pathways for oxidation reactions in supercritical water

Oxidation of the products of human metabolism in supercritical water has been shown to be an efficient way to accomplish the on-board water/waste recycling in future long-term space flights. Studies of the oxidation kinetics of methane to carbon dioxide in supercritical water are presented in this paper in order to enhance the fundamental understanding of the oxidation of human waste compounds in supercritical water. It is concluded that, although the elementary reaction models remain the best hope for simulating oxidation in supercritical water, several modifications to existing mechanisms need to be made to account for the role of water in the reaction mechanism.

Webley, Paul A.↗
NASA NTRS2007

Oxidation of C/SiC Composites at Reduced Oxygen Partial Pressures

T-300 carbon fibers and T-300 carbon fiber reinforced silicon carbide composites (C/SiC) were oxidized in flowing reduced oxygen partial pressure environments at a total pressure of one atmosphere (0.5 atm O2, 0.05 atm O2 and 0.005 atm O2, balance argon). Experiments were conducted at four temperatures (816deg, 1149deg, 1343deg, and 1538 C). The oxidation kinetics were monitored using thermogravimetric analysis. T-300 fibers were oxidized to completion for times between 0.6 and 90 h. Results indicated that fiber oxidation kinetics were gas phase diffusion controlled. Oxidation rates had an oxygen partial pressure dependence with a power law exponent close to one. In addition, oxidation rates were only weakly dependent on temperature. The C/SiC coupon oxidation kinetics showed some variability, attributed to differences in the number and width of cracks in the SiC seal coat. In general, weight losses were observed indicating oxidation of the carbon fibers dominated the oxidation behavior. Low temperatures and high oxygen pressures resulted in the most rapid consumption of the carbon fibers. At higher temperatures, the lower oxidation rates were primarily attributed to crack closure due to SiC thermal expansion, rather than oxidation of SiC since these reduced rates were observed even at the lowest oxygen partial pressures where SiC oxidation is minimal.

Opila, E. J.↗
DOE OSTI2022

UK-US Collaboration on Fossil Energy R&D: Steam Side Oxidation

In recent years, interest in increasing the efficiency of power plants based on steam generation has led to the need to develop and qualify materials capable of operating at steam temperatures and pressures significantly higher than those employed in current power plants. The overall focus of this international program is on using ferritic-martensitic steels to the maximum possible temperature, before switching to austenitic steels and/or Ni-based alloys. The relatively low Cr content of these alloys raises concerns regarding their resistance to steam oxidation at these higher temperatures. Earlier work in this collaboration addressed the reliability of data from atmospheric pressure, laboratory-based steam oxidation tests. This raised issues regarding how representative the laboratory-grown oxides were compared to those formed on service-exposed material and how the tests could be made more reliable by introducing added complexity. In general laboratory-scale exposures are conducted under isothermal conditions at ambient or slightly elevated pressure, using a relatively low flow rate of steam. The coupons used in these tests are normally flat cuboids which have been ground to homogenise the surface and remove any pre-existing features. However, there is a concern that these samples and exposures are not representative of service conditions, and so it is necessary to quantify the influence of transient conditions, such as heat flux, pressure and sample geometry/surface conditions. To address such concerns a new collaborative program of work was initiated to determine the influence of these added features on oxidation kinetics and oxide scale morphology. The overall aim was to improve the understanding of alloy performance in ultrasupercritical (USC) steam conditions and qualify suitable test procedures.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2021

High temperature oxidation of corrosion resistant alloys from machine learning

Parabolic rate constants, k p , were collected from published reports and calculated from corrosion product data (sample mass gain or corrosion product thickness) and tabulated for 75 alloys exposed to temperatures between ~800 and 2000 K (~500–1700 °C; 900–3000°F). Data were collected for environments including lab air, ambient and supercritical carbon dioxide, supercritical water, and steam. Materials studied include low- and high-Cr ferritic and austenitic steels, nickel superalloys, and aluminide materials. A combination of Arrhenius analysis, simple linear regression, supervised and unsupervised machine learning methods were used to investigate the relations between composition and oxidation kinetics. The supervised machine learning techniques produced the lowest mean standard errors. The most significant elements controlling oxidation kinetics were Ni, Cr, Al, and Fe, with Mo and Co composition also found to be significant features. The activation energies produced from the machine learning analysis were in the correct distributions for the diffusion constants for the oxide scales expected to dominate in each class.

Materials Science↗
DOE OSTI2023

FWP FEAA149: “Next Generation Environmental Barrier Coatings”

Environmental barrier coatings (EBCs) are required coatings for utilization of SiC/SiC ceramic matrix composite (CMC) components in gas turbines, where the EBC represents the life-limiting factor for such components. EBC/CMC systems have shown success in aero-engine applications with increased turbine inlet temperatures and improved efficiencies, which are achieved through higher temperature stability, lower density, and decreased reliance on cooling air compared to traditional superalloys. While industrial gas turbines (IGTs) do not currently utilize SiC/SiC CMCs, the current shift towards low-carbon or carbon-free fuel sources for power generation could result in a need for EBC/CMC components with higher temperature capabilities. In this work, three tasks were outlined to improve understanding of EBC lifetimes to encourage use in IGTs with carbon-free fuel such as hydrogen: 1. Define the bond coating oxidation kinetics and EBC failure criteria, 2. Measure thermal expansion coefficients of each layered material, and 3. Perform advanced characterization and modeling to assess EBC lifetimes. Cyclic steam oxidation tests were conducted on various EBC/Si/SiC chemistries and EBC/SiC architectures to define substrate oxidation kinetics and EBC failure modes. An open-source code was developed to quantify the undulating thermally grown oxide thickness with thousands of measurements from specimen cross-section images. Bond coating oxidation kinetics were determined and used to develop a kinetic and thermodynamic model for predicting EBC lifetimes. High-temperature Raman spectroscopy was utilized for determining the SiO 2 thermally grown oxide phase transformation as the life-limiting feature for EBCs. Model efforts supported the claim that the SiO 2 phase transformation causes elevated stress during thermal cycling with associated cracking that decreases the adhesion strength of the EBC, eventually resulting in coating spallation. The finite element model subroutine will be made publicly available upon internal review. Further development of an EBC lifetime model for IGTs involves definition of a critical SiO 2 thickness for EBC spallation and must also consider both environmental (gas velocity, pressure, etc.) and specimen (EBC dopants, layer architectures, etc.) effects into predicted bond coating oxidation kinetics for long-lifetime components.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Phase-field modeling of alloy oxidation at high temperatures

Oxide growth is a complex process involving transport of reactive species, heterogeneous reactions, and microstructure evolution. Predicting oxidation kinetics and especially the oxide morphological change has been a long-standing challenge. Here we develop a phase-field model for predicting the oxide growth kinetics of a multicomponent alloy during high temperature oxidation, focusing on internal oxidation (non-protective) and its transition to external oxidation (protective). In this work, the predicted kinetics and oxide morphology are analyzed and compared to the classical Wagner’s theory and an existing analytical model by Zhao and Gleeson. Some assumptions used in the analytical models and the limitation are discussed. In addition, it is demonstrated that the morphology and distribution of the initial oxide nuclei play an important role in the later stage oxide connectivity and thus the transition to external oxidation.

36 MATERIALS SCIENCE↗
NASA NTRS2010

Oxidation of SiC Fiber-Reinforced SiC Matrix Composites with a BN Interphase

SiC-fiber reinforced SiC matrix composites with a BN interphase were oxidized in reduced oxygen partial pressures of oxygen to simulate the environment for hypersonic vehicle leading edge applications. The constituent fibers as well as composite coupons were oxidized in oxygen partial pressures ranging from 1000 ppm O2 to 5% O2 balance argon. Exposure temperatures ranged from 816 C to 1353 C (1500 F to 2450 F). The oxidation kinetics of the coated fibers were monitored by thermogravimetric analysis (TGA). An initial rapid transient weight gain was observed followed by parabolic kinetics. Possible mechanisms for the transient oxidation are discussed. One edge of the composite coupon seal coat was ground off to simulate damage to the composite which allowed oxygen ingress to the interior of the composite. Oxidation kinetics of the coupons were characterized by scanning electron microscopy since the weight changes were minimal. It was found that sealing of the coupon edge by silica formation occurred. Differences in the amount and morphology of the sealing silica as a function of time, temperature and oxygen partial pressure are discussed. Implications for use of these materials for hypersonic vehicle leading edge materials are summarized.

Opila, Elizabeth↗
DOE OSTI2026

A kinetic model for simulating non-equilibrium mass transport in oxides applied to hematite growth under irradiation

We propose an approach to simulating the dynamic evolution and transport of charged point defects within and through the oxide scales that form during corrosion. The method follows the cluster dynamics formalism widely adopted for radiation damage in solids, which can apply in both quasi-static and far from equilibrium conditions, such as in radiation environments. By treating each charged defect as a cluster of an atomic defect and associated unit charges, the proposed model flexibly allows charge state transitions and shifts in the Fermi level by absorption and emission of charge carriers from point defects in a reaction network with rates constrained by local equilibrium. Applying this model to hematite predicts changes in self-diffusion and oxidation kinetics in irradiation environments, surprisingly showing reduced oxidation rates in many conditions, despite enhanced self-diffusion. In conclusion, the origin of this effect lies in a change in Fermi level induced by excess vacancies formed under irradiation, which in turn suppresses the transport of cation interstitials which facilitate hematite growth.

36 MATERIALS SCIENCE↗