Search NASA⌕ Search

SEARCH · Search NASA

Results for “oxidizing environments”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Effects of Material Degradation on the Structural Integrity of Composite Materials: Experimental Investigation and Modeling of High Temperature Degradation Mechanisms

It has previously been demonstrated that simple coupled reaction-diffusion models can approximate the aging behavior of PMR-15 resin subjected to different oxidative environments. Based on empirically observed phenomena, a model coupling chemical reactions, both thermal and oxidative, with diffusion of oxygen into the material bulk should allow simulation of the aging process. Through preliminary modeling techniques such as this it has become apparent that accurate analytical models cannot be created until the phenomena which cause the aging of these materials are quantified. An experimental program is currently underway to quantify all of the reaction/diffusion related mechanisms involved. The following contains a summary of the experimental data which has been collected through thermogravimetric analyses of neat PMR-15 resin, along with analytical predictions from models based on the empirical data. Thermogravimetric analyses were carried out in a number of different environments - nitrogen, air and oxygen. The nitrogen provides data for the purely thermal degradation mechanisms while those in air provide data for the coupled oxidative-thermal process. The intent here is to effectively subtract the nitrogen atmosphere data (assumed to represent only thermal reactions) from the air and oxygen atmosphere data to back-figure the purely oxidative reactions. Once purely oxidative (concentration dependent) reactions have been quantified it should then be possible to quantify the diffusion of oxygen into the material bulk.

Cunningham, Ronan A.↗
DOE OSTI2023

Insights into the thermal history of carbon fibers using Raman spectroscopy and a novel kinetic model

Carbon fibers and carbon fiber composites are applied in high-performance applications, but a key consideration for application is their relative sensitivity to oxidative environments. To enable in-situ characterization of carbon fibers exposed to oxidative conditions, the Raman spectral response of T700 carbon fibers that have been exposed to a variety of dwell temperatures is reported herein with dwell times reaching up to 1 month. Here, we evaluate the spectra holistically by using integrated absolute difference analysis. By combining this analysis with straightforward kinetic models, we connect the total Raman spectral response to the temperature-time curve that could yield such a shift in spectral parameters. Our work connects the Raman spectral response of carbon fibers to their thermal history and can easily be extended to other graphitic materials, such as nuclear graphite.

36 MATERIALS SCIENCE↗
NASA NTRS2017

Europa Propulsion Valve Seat Material Testing

The Europa mission and spacecraft design presented unique challenges for selection of valve seat materials that met the fluid compatibility requirements, and combined fluid compatibility and high radiation exposure level requirements. The Europa spacecraft pressurization system valves will be exposed to fully saturated propellant vapor for the duration of the mission. The effects of Nitrogen Tetroxide (NTO) and Monomethylhydrazine (MMH) propellant vapors on heritage valve seat materials, such as Vespel SP-1 and Polychlorotrifluoroethylene (PCTFE), were evaluated to determine if an alternate material is required. In liquid system applications, Teflon is the only available compatible valve seat material. Radiation exposure data for Teflon in an air or vacuum environment has been previously documented. Radiation exposure data for Teflon in an oxidizer environment such as NTO, was not available, and it was unknown whether the effects would be similar to those on air-exposed samples. Material testing was conducted by Marshall Space Flight Center (MSFC) and White Sands Test Facility (WSTF) to determine the effects of propellant vapor on heritage seat materials for pressurization valve applications, and the effects of combined radiation and NTO propellant exposure on Teflon. The results indicated that changes in heritage pressurization valve seat materials' properties rendered them unsuitable for the Europa application. The combined radiation and NTO exposure testing of Teflon produced results equivalent to combined radiation and air exposure results.

Addona, Brad M.↗
DOE OSTI2023

Biphasic Janus Particles Explain Self-Healing in Pt–Pd Diesel Oxidation Catalysts

The addition of Pd to Pt-based diesel oxidation catalysts is known to enhance performance and restrict the anomalous growth of Pt nanoparticles when subjected to aging at high temperatures in oxidative environments. To gain a mechanistic understanding, we studied the transport of the mobile Pt and Pd species to the vapor phase, since vapor phase transport is the primary route for sintering in these catalysts. The results are surprising: there is a 30-fold drop in the effective vapor pressure of Pt in the Pt-Pd catalysts compared to monometallic Pt. At the same time, there is a significant enhancement in the vapor pressure of Pd, compared to PdO, which otherwise has a negligible vapor pressure at the aging temperature. Such behavior cannot be explained simply by alloying Pt and Pd in the metallic phase, or a core-shell morphology where a PdO shell covers a Pt core. Transmission electron microscopic examination of catalysts aged up to 50 h in air at 800 °C shows that the particles exhibit a biphasic “Janus”-like structure. The metal and oxide phases are conjoined, exposing a metal and an oxide face to the gas phase. The high mobility of the Pt and Pd allows them to be partitioned into the metal and oxide phases, in apparent thermodynamic equilibrium. The PdO helps to trap mobile PtO2 and as a result contains high concentrations of Pt oxide, consistent with its role in mitigating the transport of Pt to the vapor phase and preventing the growth of anomalously large particles. In turn, Pt allows Pd to remain metallic, allowing the catalyst to retain both metal and oxide functionality for catalysis. The regeneration of deactivated catalysts typically requires an external input, such as a change in the working environment from reducing to oxidizing or vice-versa. Here, we show that the mobile species, which are primary contributors to catalyst sintering are effectively returned to the active site, hence our use of the term “selfhealing”. The detailed insights into the inner workings of the Pt-Pd diesel oxidation catalysts can help provide clues to the design of robust and durable heterogeneous catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1989

Carbon/Carbon Panels Cooled By Heat Pipes

Durable and reusable high-temperature carbon/carbon heat-pipe structure operates at temperatures above 3,000 degree F (1,649 degree C) in vacuum or inert environment and up to 2,800 degree F (1,537 degree C) in oxidizing environment. New concept combines high-temperature heat-pipe and carbon/carbon technologies to extend both thermal structural capabilities of refractory-metal heat pipes and maximum heat-flux capability of carbon/carbon structures. Uses refractory-metal heat pipes embedded within carbon/carbon structure. Walls of heat pipes thin and contain working fluid (lithium or sodium) of heat pipe. Carbon/carbon acts as primary load-carrying part of structure. Heat pipes help to eliminate local hotspots and associated thermal gradients and stresses and to reduce peak surface temperatures of carbon/carbon to levels within capability of oxidation-resisting system.

Camarda, Charles J.↗
NASA NTRS1985

Thermal barrier coating life prediction model development

A methodology was established to predict thermal barrier coating life in an environment simulative of that experienced by gas turbine airfoils. Specifically, work is being conducted to determine failure modes of thermal barrier coatings in the aircraft engine environment. Analytical studies coupled with appropriate physical and mechanical property determinations are being employed to derive coating life prediction model(s) on the important failure mode(s). An initial review of experimental and flight service components indicates that the predominant mode of TBC failure involves thermomechanical spallation of the ceramic coating layer. This ceramic spallation involves the formation of a dominant crack in the ceramic coating parallel to and closely adjacent to the metal-ceramic interface. Initial results from a laboratory test program designed to study the influence of various driving forces such as temperature, thermal cycle frequency, environment, and coating thickness, on ceramic coating spalling life suggest that bond coat oxidation damage at the metal-ceramic interface contributes significantly to thermomechanical cracking in the ceramic layer. Low cycle rate furnace testing in air and in argon clearly shows a dramatic increase of spalling life in the non-oxidizing environments.

Sheffler, K. D.↗
DOE OSTI2021

Review of Graphite Properties Relevant to Micro-Reactor Design

Microreactors are advanced reactors that are designed to be small, scalable, and portable with up to 20 MW power. These reactors could operate independently, or as part of a microgrid, without need of a frequent refueling. Micro-reactors are designed to be deployable to provide electric power in remote locations, therefore providing greater flexibility. Several micro-reactors are under development in the US. These reactors are based on advanced gas-cooled or heat-pipe concepts. While Graphite can be found in various applications, some high-temperature reactors plan to employ Graphite in their core components due to its role as a moderator and its ability to maintain its structural integrity when subjected to elevated temperatures and high neutron fluence. Although there is significant experience with use of Graphite in nuclear applications, there are still unknowns that should be addressed. Graphite properties depend on the graphite type and affected by the fabrication procedures. Material properties are functions of the temperature and irradiation dose. The fundamental properties also affected by the oxidation environment. Therefore, in-depth understanding of graphite properties, including the effect of irradiation, oxidation and other influencing parameters are required to evaluate the design accurately. This draft aims to provide a comprehensive review of material properties for Graphite relevant to micro reactor design. For this work, two distinct grades of graphite were considered, namely IG-110 and Mersen-2114. Physical, thermal, and mechanical properties for these grades were comparatively evaluated. The properties that are discussed in this draft aim to serve as a basis for design and safety analysis.

42 ENGINEERING↗
NASA NTRS1993

Wear modes active in angular contact ball bearings operating in liquid oxygen environment of the Space Shuttle turbopumps

Extensive experimental investigation has been carried out on used flight bearings of the high pressure oxidizer turbopumps (HPOTP) of the space shuttle main engine (SSME) in order to determine the dominant wear modes, their extent, and causes. The paper presents the methodology, various surface analysis techniques used, results, and discussion. The mode largely responsible for premature bearing wear has been identified as adhesive/shear peeling of the upper layers of bearing balls and rings. This mode relies upon the mechanisms of scale formation, breakdown, and removal, all of which are greatly enhanced by the heavy oxidation environment of the HPOTP. Major causes of the high wear rates appear to be lubrication and cooling, both inadequate for the imposed conditions of operation. Numerous illustrations and evidence are provided.

Chase, Thaddeus J.↗
DOE OSTI2022

Structure characterization and steam oxidation performance of U 3 Si 2 with Zr alloying additions

Research and development of high uranium density fuels supports the on-going effort to enhance reactor technology, safety, performance, and economics. Among high uranium density fuels, U 3 Si 2 is a favored fuel candidate due to its higher uranium density and improved thermal conductivity when compared to traditional UO 2 . While U 3 Si 2 demonstrates an improved fuel economy, it suffers from rapid degradation when exposed to water at T > 300°C. In order for U 3 Si 2 to be implemented in water cooled reactors, the water reaction must be understood and mitigated. Reported here is the performance of Zr alloying additions to U 3 Si 2 exposed to high temperature steam oxidation environments. Here, the investigation shows that homogenization heat treatment contributes to a delayed onset of oxidation and an improved homogeneity throughout the arc-melt fabricated alloyed compositions. Of the pre- and post-annealed samples, the post-annealed 7 vol% Zr addition exhibited the highest onset temperature of oxidation. A preliminary computational investigation to complement the experimental analysis assesses the solubility of Zr in U 3 Si 2 and its incorporation in the crystal lattice.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
NASA NTRS1985

Bismaleimides and related maleimido polymers as matrix resins

Significant processing and property improvements can be achieved by copolymerization of state-of-the-art bisimides with various vinyl stilbazole derivatives to give both fire resistance and high-temperature properties from hot-melt compositions. Significant improvement in mechanical properties is achieved through these modifications, which may make these new matrix resins ideal candidates for fireworthy secondary graphite composite structures. Phosphorous modifications of maleimido polymers through phosphonate structure and tricyclophosphazene derivatives provide families of new matrix resins for short-time applications in severe thermo-oxidative environments. With further research these may provide matrix resins for long-term thermo-oxidative stability of advanced composites at temperatures up to 400 to 500 C.

Parker, J. A.↗
NASA NTRS1988

Carbon-carbon - An overview

In nonoxidizing high-temperature environments, carbon-carbon composites retain room temperature properties to more than 2225 C; in oxidizing environments, the variety of coatings thus far developed limits maximum operating temperatures to about 1600 C. The high thermal conductivity and low thermal expansion of these composites renders them ideal for applications encountering thermal shocks. In addition, the variety of fibers, weave patterns, and layup procedures that can be used for the composites allows mechanical properties to be carefully tailored over a wide range to fit the application in question.

Buckley, John D.↗
NASA NTRS1994

High-Temperature, Oxidation-Resistant Thermocouples

Aluminum substituted for rhodium, which is scarce and expensive. Electromotive force increases with aluminum content in Pt/Al leg of Pt(Pt/Al) thermocouple. Wires baked longer in aluminizing bed produce larger voltages. Thermocouples containing platinum/aluminum legs used instead of thermocouples of type R in furnaces, heat engines, and chemical reactors. Expecially suited to high-velocity oxidizing environments. Constructed as thin-film sensors on turbine blades and vanes, where pre-oxidation provides insulating film needed between thermocouple legs. Because aluminum content slowly depleted by oxidation, long-term use recommended only where maximum temperature is 1,200 degrees C or less.

Smialek, James L.↗
NASA NTRS1992

Thermodynamics, Solubility, and Diffusivity of Oxygen in Titanium and Ti-Al Alloys

Titanium aluminides and titanium aluminide-based composites are attractive candidate materials for high-temperature structural applications. As these materials may be exposed to oxidizing environments durine their use at elevated temperatures, it is essential that they possess a good oxidation resistance. Previous studies have shown that the oxidation resistance of Al-rich alloys in the Ti-Al system is superior to that of the Ti-rich alloys. The scales formed on the surface of the Al-rich and Ti-rich alloys have been reported to be predominantly Al2O3 and TiO2, respectively. Since the relative stabilities of the oxides of Al and Ti at various temperatures and oxygen pressures can be assessed from their thermodynamic data, it is possible, With the help of thermodynamic calculations, to determine the compositions of the alloys which would form scales of Al2O3, TiO(x) or a ternary oxide such as TiAl2O5 during oxidation at a given temperature. The thermodynamic calculations require reliable activity data for the Ti-Al system. These data have not been determined for the entire composition and temperature range of interest. Using the data available in the literature, recently performed thermodynamic calculations and concluded that the stable oxide changed from TiO to Al2O3 in the existence region of the tial phase. In the case of titanium aluminide-based composites, another major concern is the mutual chemical compatibility of the matrix material with the reinforcement phase. Fibers of SiC, TiB2 and Al2O3 are currently being investigated for reinforcement of titanium aluminide matrices.

Mehrotra, Gopal M.↗
NASA NTRS2001

Tensile Strength and Microstructure of Al2O3-ZrO2 Hypo-Eutectic Fibers Studied

Oxide eutectics offer high-temperature strength retention and creep resistance in oxidizing environments. Al2O3-ZrO2 eutectic strengths have been studied since the 1970's. Directionally solidified oxide eutectics exhibit improved resistance to slow crack growth and excellent strength retention at high temperatures up to 1400 C. Materials studied typically contain Y2O3 to metastably retain the high-temperature cubic and tetragonal polymorphs at room temperature. Al2O3-ZrO2 is of fundamental interest for creep studies because it combines a creep-resistant material, Al2O3, with a very low creep resistance material, ZrO2. Results on mechanical properties and microstructures of these materials will be used to define compositions for creep testing in future work. Substantial variations from the eutectic alumina to zirconia ratio can be tolerated without a loss in room-temperature strength. The effect of increasing Y2O3 addition on the room-temperature tensile strength of an Al2O3-ZrO2 material containing excess Al2O3 was examined at the NASA Glenn Research Center, where the materials were grown using Glenn's world-class laser growth facilities.

Farmer, Serene C.↗
NASA NTRS2005

Performance of Ceramics in Severe Environments

Ceramics are generally stable to higher temperatures than most metals and alloys. Thus the development of high temperature structural ceramics has been an area of active research for many years. While the dream of a ceramic heat engine still faces many challenges, niche markets are developing for these materials at high temperatures. In these applications, ceramics are exposed not only to high temperatures but also aggressive gases and deposits. In this chapter we review the response of ceramic materials to these environments. We discuss corrosion mechanisms, the relative importance of a particular corrodent, and, where available, corrosion rates. Most of the available corrosion information is on silicon carbide (SIC) and silicon nitride (Si3N4) monolithic ceramics. These materials form a stable film of silica (SO2) in an oxidizing environment. We begin with a discussion of oxidation of these materials and proceed to the effects of other corrodents such as water vapor and salt deposits. We also discuss oxidation and corrosion of other ceramics: precurser derived ceramics, ceramic matrix composites (CMCs), ceramics which form oxide scales other than silica, and oxide ceramics. Many of the corrosion issues discussed can be mitigated with refractory oxide coatings and we discuss the current status of this active area of research. Ultimately, the concern of corrosion is loss of load bearing capability. We discuss the effects of corrosive environments on the strength of ceramics, both monolithic and composite. We conclude with a discussion of high temperature wear of ceramics, another important form of degradation at high temperatures.

Jacobson, Nathan S.↗
NASA NTRS1997

Smoldering Combustion Experiments in Microgravity

The Microgravity Smoldering Combustion (MSC) experiment is part of a study of the smolder characteristics of porous combustible materials in a microgravity environment. Smoldering is a non-flaming form of combustion that takes place in the interior of porous materials and takes place in a number of processes ranging from smoldering of porous insulation materials to high temperature synthesis of metals. The objective of the study is to provide a better understanding of the controlling mechanisms of smolder, both in microgravity and normal-gravity. As with many forms of combustion, gravity affects the availability of oxidizer and transport of heat, and therefore the rate of combustion. Microgravity smolder experiments, in both a quiescent oxidizing environment, and in a forced oxidizing flow have been conducted aboard the NASA Space Shuttle (STS-69 and STS-77 missions) to determine the effect of the ambient oxygen concentration and oxidizer forced flow velocity on smolder combustion in microgravity. The experimental apparatus is contained within the NASA Get Away Special Canister (GAS-CAN) Payload. These two sets of experiments investigate the propagation of smolder along the polyurethane foam sample under both diffusion driven and forced flow driven smoldering. The results of the microgravity experiments are compared with identical ones carried out in normal gravity, and are used to verify present theories of smolder combustion. The results of this study will provide new insights into the smoldering combustion process. Thermocouple histories show that the microgravity smolder reaction temperatures (Ts) and propagation velocities (Us) lie between those of identical normal-gravity upward and downward tests. These observations indicate the effect of buoyancy on the transport of oxidizer to the reaction front.

Walther, David C.↗
DOE OSTI2021

Oxide evolution on the SiC layer of TRISO particles during extended air oxidation

Tristructural isotropic (TRISO) fuel particles have been primarily developed for high-temperature gas-cooled nuclear reactors and can be subjected to oxidizing environments for extended periods in an off-normal accident scenario. Surrogate TRISO fuel particles were oxidized in air at 1,000 or 1,100 °C for up to 120 h. Here, the oxide scale morphology and thickness were studied via scanning electron microscopy, focused ion beam, and atomic force microscopy. TRISO particles oxidized at 1,100 °C exhibited a highly crystalline oxide scale, which led to significant cracking and irregularly shaped closed porosity, whereas those oxidized at 1,000 °C possessed a primarily amorphous oxide scale, which contained small, rounded internal pores and no larger defects. The observed phenomena deviated from the expected behavior based on models for oxide growth on flat-plate and fiber SiC. The oxidation kinetics of TRISO fuel particles in high-temperature air were investigated without mechanically deforming the surface and were analyzed with respect to oxide morphology.

36 MATERIALS SCIENCE↗
NASA NTRS1985

Device and method for frictionally testing materials for ignitability

Test apparatus for determining ignition characteristics of various metal in oxidizer environments simulating operating conditions for materials is invented. The test apparatus has a chamber through which the oxidizing agent flows, and means for mounting a stationary test sample therein, a powered, rotating shaft in the chamber rigidly mounts a second test sample. The shaft is axially movable to bring the samples into frictional engagement and heated to the ignition point. Instrumentation connected to the apparatus provides for observation of temperatures, pressures, loads on and speeds of the rotating shaft, and torques whereby components of stressed oxygen systems can be selected which will avoid accidental fires under working conditions.

Benz, F. J.↗