Search NASA⌕ Search

SEARCH · Search NASA

Results for “passivated contacts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Progress in p(+)n InP solar cells fabricated by thermal diffusion

The performance results of our most recently thermally diffused InP solar cells using the p(+)n (Cd,S) structures are presented. We have succeeded in fabricating cells with measured AMO, 25 C V(sub oc) exceeding 880 mV (bare cells) which to the best of our knowledge is higher than previously reported V(sub oc) values for any InP homojunction solar cells. The cells were fabricated by thinning the emitter, after Au-Zn front contacting, from its initial thickness of about 4.5 microns to about 0.6 microns. After thinning, the exposed surface of the emitter was passivated by a thin (approximately 50A) P-rich oxide. Based on the measured EQY and J(sub sc)-V(sub oc) characteristics of our experimental high V(sub oc) p(+)n InP solar cells, we project that reducing the emitter thickness to 0.3 microns, using an optimized AR coating, maintaining the surface hole concentration of 3 x 10(exp 18)cm(sup -3), reducing the grid shadowing from actual 10.55 percent to 6 percent and reducing the contact resistance will increase the actual measured 12.57 percent AMO 25 C efficiency to about 20.1 percent. By using our state-of-the-art p(+)n structures which have a surface hole concentration of 4 x 10(exp 18)cm(sup -3) and slightly improving the front surface passivation, an even higher practically achievable AMO, 25 C efficiency of 21.3 percent is projected.

Flood, D. J.↗
NASA NTRS1993

Passive intermodulation generation in wire mesh deployable reflector antennas

Deployable reflector antennas represent a proven technology with obvious benefits for mobile satellite applications. Harris Corporation has provided deployable reflector antennas for NASA's Tracking and Data Relay Satellite System (TDRSS). These antennas utilize a rigid, radial rib unfurlable reflector with a wire mesh surface. This type of mesh has been identified as a potential design risk for multichannel communications applications based on the potential for generation of Passive Intermodulation (PIM). These concerns are based on the existence of numerous, nonpermanent metal to metal contacts that are inherent to the mesh design. To address this issue, Harris has an ongoing IR&D program to characterize mesh PIM performance. This paper presents the results of the investigation into mesh PIM performance to date and provides background information on the design and performance of the Harris radial rib deployable reflector.

Turner, Gregory M.↗
NASA NTRS2005

Methods for Anticipating Problems with Electrical Wiring

Passive and active methods for anticipating problems with electrical wiring are provided. An insulative material in contact with an electrical conductor has at least one impurity that is impregnated in the insulative material and/or disposed thereon. An environment around the electrical conductor is monitored for the presence or the level of the impurity(ies) emanating from the insulative material in the form of a gaseous effluent. An alarm signal is generated when a predetermined level of the gaseous effluent is detected.

William T Yost↗
NASA NTRS1980

Active heat exchange system development for latent heat thermal energy storage

Various active heat exchange concepts were identified from among three generic categories: scrapers, agitators/vibrators and slurries. The more practical ones were given a more detailed technical evaluation and an economic comparison with a passive tube-shell design for a reference application. Two concepts selected for hardware development are a direct contact heat exchanger in which molten salt droplets are injected into a cooler counterflowing stream of liquid metal carrier fluid, and a rotating drum scraper in which molten salt is sprayed onto the circumference of a rotating drum, which contains the fluid heat sink in an internal annulus near the surface. A fixed scraper blade removes the solidified salt from the surface which has been nickel plated to decrease adhesion forces. Suitable phase change material (PCM) storage media with melting points in the temperature range of interest (250 C to 400 C) were investigated. The specific salt recommended for laboratory tests was a chloride eutectic (20.5KCl-24/5 NaCl-55.0MgCl 2% by wt.), with a nominal melting point of 385 C.

Alario, J.↗
NASA NTRS2008

Chemical Passivation of Li(exp +)-Conducting Solid Electrolytes

Plates of a solid electrolyte that exhibits high conductivity for positive lithium ions can now be passivated to prevent them from reacting with metallic lithium. Such passivation could enable the construction and operation of high-performance, long-life lithium-based rechargeable electrochemical cells containing metallic lithium anodes. The advantage of this approach, in comparison with a possible alternative approach utilizing lithium-ion graphitic anodes, is that metallic lithium anodes could afford significantly greater energy-storage densities. A major impediment to the development of such cells has been the fact that the available solid electrolytes having the requisite high Li(exp +)-ion conductivity are too highly chemically reactive with metallic lithium to be useful, while those solid electrolytes that do not react excessively with metallic lithium have conductivities too low to be useful. The present passivation method exploits the best features of both extremes of the solid-electrolyte spectrum. The basic idea is to coat a higher-conductivity, higher-reactivity solid electrolyte with a lower-conductivity, lower-reactivity solid electrolyte. One can then safely deposit metallic lithium in contact with the lower-reactivity solid electrolyte without incurring the undesired chemical reactions. The thickness of the lower-reactivity electrolyte must be great enough to afford the desired passivation but not so great as to contribute excessively to the electrical resistance of the cell. The feasibility of this method was demonstrated in experiments on plates of a commercial high-performance solid Li(exp +)- conducting electrolyte. Lithium phosphorous oxynitride (LiPON) was the solid electrolyte used for passivation. LiPON-coated solid-electrolyte plates were found to support electrochemical plating and stripping of Li metal. The electrical resistance contributed by the LiPON layers were found to be small relative to overall cell impedances.

West, William↗
NASA NTRS1986

Electrodynamic interactions

The electrodynamic interaction of long metallic tethers with the ionosphere is introduced. Due to the tether's motion across the Earth's field, a polarization electric field is generated along the tether. In a system like the Tethered Satellite System (TSS) where the tether is coated with dielectric and the electrical contact is between its two terminations and the ionosphere, the upper end termination will collect electrons and, in a passive system, the lower end termination will collect ions. Space charge regions will develop around the two terminations of the system, which can be at considerable potential with respect to the unperturbed ionospheric plasma and the current in the tether will be most significantly determined by local processes in such space charge regions. A qualitative view of the global perturbation induced by TSS in the ionosphere is outlined. One of the applications of electrodynamic tethers is that of using them as low frequency wave generators to communicate to the Earth. This application is briefly discussed. An equivalent circuit of the tether system is described. The basic equation of the circuit is given.

Dobrowolny, M.↗
NASA NTRS1991

An investigation to determine the producibility of a 3-D braider and bias direction weaving loom

The development of prototype machines for the production of generalized braid patterns is described. Mechanical operating principles and control strategies are presented for two prototype machines which were fabricated and evaluated. Both machines represent advances over current techniques for forming composite material preforms by enabling near ideal control of fiber orientation. Furthermore, they overcome both the lack of general control of produced fiber architectures and the complexity of other weaving processes that were produced for the same purpose. One prototype, the modified Farley braider, consists of an array of turntables which can be rotated 90 degrees and returned; hence, they can form tracks in the x and y axis. Yarn ends are transported about the surface formed by the turntables using motorized tractors. These tractors are controlled using an optical link with a control circuit and host computer. The tractors are powered through electrical contact with the turntables. The necessary relative motions are produced by a series of linear tractor moves combined with a sequence of turntable rotations. The movement of the tractors about the surface causes the yarns to produce the desired braiding pattern. The second device, the shuttle plate braider, consists of a braiding surface formed by an array of square elements, each separated from its neighbor by a gap. Beneath this surface lies a shuttle plate, which reciprocates first in one axis and then in the other. As this movement takes place, yarn carrying shuttles engage and disengage the plate by means of solenoid activated pins. By selective engagement and disengagement, the shuttles can move the yarn ends in any desired pattern, forming the desired braid. Control power, and control signals, are transmitted from the electronic interface circuit and host computer, via the braiding surface through electrical contact with the shuttles. Motive power is proved to the shuttles by motion of the shuttle plate, which is passively driven using pneumatic rams. Each shuttle is a simple device that uses only a solenoid to engage the plate and is a simple device that uses only a solenoid to engage the plate and is independently controllable. When compared with each other, the modified Farley braider has the advantage of speed, and the shuttle plate braider the advantage of mechanical control and simplicity.

Huey, Cecil O., Jr.↗
NASA NTRS2018

Nanoscale Fabrication of Microwave Detectors from Commercially-Available CVD-Grown Monolayer Graphene

Using commercially-available monolayer graphene, synthesized by means of chemical vapor deposition, microwave power sensing elements have been nanofabricated and integrated with microwave-grade test structures suitable for on-wafer probing. The graphene, situated on a thermal oxide, was first cleaned of stray contaminants in a forming gas environment briefly held at 250 degrees Celsius using a rapid thermal annealer. Immediately following this step, the graphene was passivated with a protective aluminum oxide layer (approximately S nm in thickness). Micrometer-scale Corbino disc test structures were then fabricated in direct contact with the graphene using a self-aligned process, which relies on the fact that tetramethylammonium hydroxide develops the photoresist while removing the aluminum oxide. Graphene nanoribbons (with widths as small 400 nm) were then fabricated across the Corbino disc gaps using electron-beam writing in conjunction with a negative tone resist. The same developer exposed the majority of the graphene while defining nanometer-scale lines of photoresist stacked upon aluminum oxide. These stacks served as etch-stops while the unprotected graphene was ion-milled in an oxygen plasma. Finally, the photoresist was removed leaving behind passivated graphene nanoribbons. Damage caused by the fabrication was evaluated by comparing the Raman spectra of the grapheme before and after processing.

detectors↗
NASA NTRS1970

Brushless direct-current motor with stationary armature and field

Electronically commutated dc motor has an active fixed field winding, and active fixed armature winding, and passive rotor. By use of brushless dc motor switching technique, motor provides continuous controllable and reversible torque without use of sliding contacts.

Studer, P. A.↗
NASA NTRS1992

Connection space reduction mechanism

A connector assembly comprised of two halves, each respectively including a shell type connector subassembly, one being an active half and the other being a passive half is described. The active half includes an alignment cusp that causes a coupling motion in response to coming in contact with the outer portion of the other half, which causes the respective connectors within the two subassemblies to move toward each other into coupling relationship at twice the rate at which the two subassemblies come together. Both halves are adapted to rotate about and translate along respective mutually orthogonal axes to facilitate an interconnection.

Milam, Malcolm Bruce↗
NASA NTRS1993

The Robotic All-Terrain Lunar Exploration Rover (RATLER): Increased mobility through simplicity

A new concept mobility chassis for a robotic rover is described which is inherently simple with few moving parts or complex linkages. The RATLER design utilizes a four-wheel drive, skid steered propulsion system in conjunction with passive articulation of the dual body vehicle. This uniquely simple method of chassis articulation allows all four wheels to remain in contact with the ground even while climbing obstacles as large as 1.3 wheel diameters. A prototype mobility platform was built which is approximately 1 m(sup 2) with 0.5 m diameter wheels and all-wheel electric drive. The theoretical mobility limitations are discussed and compared with the results of field trials of the prototype platform. The theoretical model contrasted with measured performance is then used to predict the expected mobility of the RATLER design on the Lunar surface.

Pletta, J. Bryan↗
NASA NTRS1980

Active heat exchange system development for latent heat thermal energy storage

Various active heat exchange concepts were identified from among three generic categories: scrapers, agitators/vibrators and slurries. The more practical ones were given a more detailed technical evaluation and an economic comparison with a passive tube-shell design for a reference application (300 MW sub t storage for 6 hours). Two concepts were selected for hardware development: (1) a direct contact heat exchanger in which molten salt droplets are injected into a cooler counterflowing stream of liquid metal carrier fluid, and (2) a rotating drum scraper in which molten salt is sprayed onto the circumference of a rotating drum, which contains the fluid salt is sprayed onto the circumference of a rotating drum, which contains the fluid heat sink in an internal annulus near the surface. A fixed scraper blade removes the solidified salt from the surface which was nickel plated to decrease adhesion forces. In addition to improving performance by providing a nearly constant transfer rate during discharge, these active heat exchanger concepts were estimated to cost at least 25% less than the passive tube-shell design.

Alario, J.↗
NASA NTRS1986

Electrodynamics panel presentation

The Plasma Motor Generator (PMG) concept is explained in detail. The PMG tether systems being used to calculate the estimated performance data is described. The voltage drops and current contact geometries involved in the operation of an electrodynamic tether are displayed illustrating the comparative behavior of hollow cathodes, electron guns, and passive collectors for current coupling into the ionosphere. The basic PMG design involving the massive tether cable with little or no satellite mass at the far end(s) are also described. The Jupiter mission and its use of electrodynamic tethers are given. The need for demonstration experiments is stressed.

Mccoy, J.↗
NASA NTRS2001

Wireless Subsurface Sensors for Health Monitoring of Thermal Protection Systems on Hypersonic Vehicles

Health diagnostics is an area where major improvements have been identified for potential implementation into the design of new reusable launch vehicles (RLVs) in order to reduce life cycle costs, to increase safety margins, and to improve mission reliability. NASA Ames is leading the effort to develop inspection and health management technologies for thermal protection systems. This paper summarizes a joint project between NASA Ames and industry partners to develop "wireless" devices that can be embedded in the thermal protection system to monitor temperature or other quantities of interest. These devices are sensors integrated with radio-frequency identification (RFID) microchips to enable non-contact communication of sensor data to an external reader that may be a hand-held scanner or a large portal. Both passive and active prototype devices have been developed. The passive device uses a thermal fuse to indicate the occurrence of excessive temperature. This device has a diameter under 0.13 cm. (suitable for placement in gaps between ceramic TPS tiles on an RLV) and can withstand 370 C for 15 minutes. The active device contains a small battery to provide power to a thermocouple for recording a temperature history during flight. The bulk of the device must be placed beneath the TPS for protection from high temperature, but the thermocouple can be placed in a hot location such as near the external surface.

Milos, Frank S.↗
NASA NTRS2003

Passive Fetal Heart Monitoring System

A fetal heart monitoring system and method for detecting and processing acoustic fetal heart signals transmitted by different signal transmission modes. One signal transmission mode, the direct contact mode, occurs in a first frequency band when the fetus is in direct contact with the maternal abdominal wall. Another signal transmission mode, the fluid propagation mode, occurs in a second frequency band when the fetus is in a recessed position with no direct contact with the maternal abdominal wall. The second frequency band is relatively higher than the first frequency band. The fetal heart monitoring system and method detect and process acoustic fetal heart signals that are in the first frequency band and in the second frequency band.

Zuckerwar, Allan J.↗
NASA NTRSDate not supplied

Work Function Matching Passive Lunar Dust Mitigation Coating Preparation for Lunar Flight Opportunity

With the Artemis program, NASA isplanning longer stays on the surface, with more activities that have the potential to put the astronauts and equipment in contact with greater quantities of lunar dust. The success of these missions will depend on our understanding of material interactions with lunar dust and the development of ways to mitigate dust effects. This is particularly truein cases where exposure to dust will lead to failure of components, unacceptable loss of power or thermal control, unacceptable loss of visibility, or health issues.Optically transparent, sputter deposited,work function matching coatings are being developed at NASA Glenn Research Center to reduce adhesion of dust to windows, lenses and display panels by matching the minimum energy to remove an electron from the surface to that oflunar dust in order to reduce adhesion due to charge transfer. One of these work function matching coatings will be tested as part of Aegis Aerospace Inc.’s Regolith Adherence Characterization experiment going to the lunar surface on a Commercial Lunar Payload Services (CLPS) lander in 2023. Preparation of the work function matching coating and initial characterization prior to delivery for flight integration will be discussed.

Lunar dust, passive mitigation, CLPS demonstration↗
NASA NTRS1973

Thermal and infrared testing

The detection of defective components in devices which are active heat sources, and the detection and characterization of flaws in structures that are thermally passive, but which can be nondestructively heated or cooled are described. The physical principles and thermal detectors and methods are discussed along with contact, and noncontact thermographic methods.

Engelhardt, R. E.↗
NASA NTRS1987

GaAs/AlGaAs heterostructure point-contact concentrator cells

Point-contact cells fabricated in silicon have recently achieved very high efficiencies. Applying this structure to GaAs is difficult as it requires both surface passivation of the GaAs and a film of GaAs with thickness less than 10 microns. The authors propose to overcome these difficulties by (1) using AlGaAs layers grown by OMCVD to act as front- and back-surface fields in order to confine the photogenerated minority carriers away from the surfaces, and (2) using the CLEFT technology to produce thin, separated films of this structure. It has been found that much of the necessary technologies have been developed and that the primary problem remaining to be solved is localized junction formation.

Gale, R. P.↗