Search NASA⌕ Search

SEARCH · Search NASA

Results for “patch”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

A Patch Density Recommendation based on Convergence Studies for Vehicle Panel Vibration Response resulting from Excitation by a Diffuse Acoustic Field

Fluid structural interaction problems that estimate panel vibration from an applied pressure field excitation are quite dependent on the spatial correlation of the pressure field. There is a danger of either over estimating a low frequency response or under predicting broad band panel response in the more modally dense bands if the pressure field spatial correlation is not accounted for adequately. Even when the analyst elects to use a fitted function for the spatial correlation an error may be introduced if the choice of patch density is not fine enough to represent the more continuous spatial correlation function throughout the intended frequency range of interest. Both qualitative and quantitative illustrations evaluating the adequacy of different patch density assumptions to approximate the fitted spatial correlation function are provided. The actual response of a typical vehicle panel system is then evaluated in a convergence study where the patch density assumptions are varied over the same finite element model. The convergence study results are presented illustrating the impact resulting from a poor choice of patch density. The fitted correlation function used in this study represents a Diffuse Acoustic Field (DAF) excitation of the panel to produce vibration response.

Smith, Andrew↗
NASA NTRS2012

Mechanical Development of a Very Non-Standard Patch Array Antenna for Extreme Environments

This paper describes the mechanical development of patch antenna arrays for the Juno mission. The patch arrays are part of a six-frequency microwave radiometer instrument that will be used to measure thermal emissions from Jupiter. The very harsh environmental conditions in Jupiter orbit, as well as a demanding launch environment, resulted in a design that departs radically from conventional printed circuit patch antennas. The paper discusses the development and qualification of the Juno patch array antennas, with emphasis on the materials approach that was devised to mitigate the effects of electron charging in Jupiter orbit.

Hughes, Richard↗
NASA NTRS2018

Effect of Distributed Patch of Smooth Roughness Elements on Transition in a High-Speed Boundary Layer

Surface roughness is known to have a substantial impact on the aerothermodynamic loading of hypersonic vehicles, particularly via its influence on the laminar-turbulent transition process within the boundary layer. Numerical simulations are performed to investigate the effects of a distributed region of densely packed, smooth-shaped roughness elements on the laminar boundary layer over a 7-degree half-angle, circular cone for flow conditions corresponding to a selected trajectory point from the ascent phase of the HIFiRE-1 flight experiment. For peak-to-valley roughness heights of 50 percent or less in comparison with the thickness of the unperturbed boundary layer, the computations converge to a stationary flow, suggesting that the flow is globally stable. Analysis of convective instabilities in the wake of the roughness patch indicates two dominant families of unstable disturbances, namely, a high frequency mode that corresponds to Mack mode waves modified by the wake and a lower frequency mode that corresponds to shear layer instabilities associated with the streaks in the roughness wake. Even though the peak growth rate of the later mode is more than 35 percent greater than the peak growth rates of the Mack modes, the latter modes achieve higher amplification ratios, and hence, are likely to dominate the onset of transition, which is estimated to occur slightly later than that in the unperturbed, i.e., smooth surface boundary layer. Additional computations are performed to investigate the effects of various roughness patch configurations on a Mach 3.5 flat plate boundary layer, to help guide an upcoming experiment in the Mach 3.5 Supersonic Low Disturbance Tunnel at NASA Langley Research Center. In this case, the cumulative reinforcement of basic state distortion over the length of the roughness patch is predicted to yield a significantly earlier transition than that over a smooth plate or a plate with a shorter length roughness patch.

Meelan Choudhari↗
NASA NTRSDate not supplied

A Flat-Panel 8x8 Sequentially Rotated Wideband Microstrip Patch Phased Array Antenna for K/Ka-band 6U CubeSat Communications Applications

Flat-panel electronically-scanned phased arrays have recently become a mainstream technology in the areas of radar and satellite applications, particularly due to their low profile and not having to steer the beams mechanically, both of which helps in realizing a lightweight phased array solution that also occupies a smaller volume. Typically for satellite applications, circularly polarized element radiators are often employed in order to deal with the signal fading problem. In this project, the main objective was to design a flat-panel phased array solution for 6U CubeSat communication applications. As for the required specifications, the array should have two operating bands: 22.55–23.55 GHz and 25.5–27.5 GHz, which span part of the K and Ka bands. For both these bands, the panel should be able to radiate dual circular polarization, in both transmit and receive modes, and with a stable gain performance. Since the individual bands are very closely spaced, it was realized that a single wideband design would be a better solution than a closely spaced dual-band design. Thus, a stacked microstrip patch configuration was selected for the element radiator design, which is known to be wideband. Now, it is rather difficult to realize both wide impedance and axial ratio bandwidths simultaneously, and at high frequencies, without complicating the element stacked patch design.. As a result, a sequential rotation technique wasemployed to significantly improves the axial ratio bandwidth and circular polarization purity of an array, all the while improving the pattern symmetry (P. S. Hall, “Application of Sequential Feeding to Wide Bandwidth, Circularly Polarised Microstrip Patch Arrays,” IEE Proc. H (Microw., Antennas Propag.), vol. 136, no. 5, pp. 390–398, Oct. 1989). The designed element radiator is a circularly-polarized probe-fed stacked patch antenna, which has a 10-dB matching bandwidth of 22.3– 30 GHz, with only a 5.14% axial ratio bandwidth around the center frequency of the required band, i.e., ~25 GHz. However, the resulting array demonstrates a very low axial ratio (≪ 3 dB) over the entire bandwidth, due to the application of the sequential rotation technique. The 8×8 array was able to scan up to ±51° and ±40° at frequencies 23.05 GHz and 26.5 GHz (center frequencies of the lower and upper bands), respectively, while maintaining a ≤ 3 dB axial ratio and a ≤ 3 dB gain drop from the corresponding peak broadside value at both the principle and the diagonal radiation planes. The designed layout for the 8×8 phased array prototype is shown in Fig. 1, which is currently undergoing fabrication and RF assembly. The antenna will be tested in the far-field anechoic chambers of the Antenna and Microwave Laboratory (AML) at San Diego State University and at NASA Glenn Research Center (GRC).

5G↗
NASA NTRS2024

Freddie Software Security Patching

Software applications become more complicated over time as they depend on many third-party, open-source libraries. The Freddie Platform Services team actively improves software security by addressing software bugs and vulnerabilities that negatively impact software applications, especially those providing real-time operations and services for the federal partners and industries. In order to detect bugs and patch vulnerabilities in software development and maintenance cycles, an automated and systematic approach is needed. This document describes what bugs and vulnerabilities are, and how they can be detected by using static code analyzers and software composition analysis tools. Once vulnerabilities are detected, the patching approaches, such as upgrading direct and transitive dependencies and loading custom classes first, are presented together with their strengths and weaknesses. In addition, patching walkthrough, example code, lessons learned throughout the vulnerability patching process and the recommended practices are discussed.

Chok Fung Lai↗
NASA NTRS1977

Mercurian bright patches - Evidence for physio-chemical alteration of surface material

Morphologically and photometrically anomalous patches of highly-reflective material exist inside several large Mercurian craters. Calculations assuming that the patches exhibit an average lunar photometric function yield normal albedos of .39-.45, roughly 60% higher than Aristarchus, the brightest feature on the moon. Color-ratio images derived from Mariner 10 imaging data indicate that bright patches are bluer than typical Mercurian surface material, and are surrounded by material redder than typical surface material. Local physio-chemical alteration along impact-induced fractures may have been involved in production of these uniquely Mercurian features.

Dzurisin, D.↗
NASA NTRS1985

Flow structure capturing on overset patched meshes

The present paper describes the application of a simple, robust stable implicit approach to solutions of the conservative equations of gasdynamics on either composite or overset meshes to capture flow structures such as shocks with high resolution in complex geometric domains. Without requiring special flux conservative operators, but rather, interpolating conservative variable data at mesh boundaries, the well posed upwind method provides accurate and oscillation free solutions, even when shocks cross the interior patch boundaries. In three problems with flow complexities that require grid refinement, the paper demonstrates the capability to conveniently carry out for gasdynamics the adaptive refined meshing strategy in overset patches proposed by Berger and Oliger (1984), and it extends this technique to rapidly convergent implicit methods for the Euler and Navier-Stokes equations. The numerical experiments show concretely, in a realistic aerodynamic problem, the savings in mesh points (about an order of magnitude here in two dimensions) for similar accuracy that flow structure aligned adaptive patched meshing affords compared to uniform grid refinement.

Venkatapathy, E.↗
NASA NTRS1987

Scattering from a microstrip patch

A solution to the problem of plane wave scattering by a rectangular microstrip patch on a grounded dielectric substrate is presented. The model does not include the microstrip feed, and thus doe not include the so-called 'antenna mode' component of the scattering. The solution begins by formulating an electric field integral equation for the surface current density on the microstrip patch. The integral equation is solved using the method of moments. Computed data for the patch radar cross section (RCS) is found to be in close agreement with measurements over a broad frequency range. The microstrip RCS versus frequency consists of a number of large peaks which are identified as impedance or pattern factor resonance peaks.

Newman, Edward H.↗
NASA NTRS1989

Statistical geometry of a small surface patch in a developed sea

The fractal and marginal fractal regimes in surface geometry are studied. The basic notions of fractal geometry are applied to a small surface patch in a developed sea, corresponding to the equilibrium wave number spectrum. Topothesy, outer and inner boundaries of the fractal range, and a cascade pattern in surface geometry are discussed. Theoretical predictions of whitecap and foam coverage are presented. A fractal decomposition for a surface patch is developed based on the Karhunen-Loeve expansion. The resulting series formalizes the cascade process of constructing realization of a Gaussian random patch. The implications of the research for microwave remote sensing signatures are considered.

Glazman, Roman E.↗
NASA NTRS1989

Stripline feed for a microstrip array of patch elements with teardrop shaped probes

A circularly polarized microstrip array antenna utilizing a honeycomb substrate made of dielectric material to support on one side the microstrip patch elements in an array, and on the other side a stripline circuit for feeding the patch elements in subarray groups of four with angular orientation and phase for producing circularly polarized radiation, preferably at a 0, 90, 180, and 270 degree relationship is described. The probe used for coupling each feed point in the stripline circuit to a microstrip patch element is teardrop shaped in order to introduce capacitance between the coupling probe and the metal sheet of the stripline circuit that serves as an antenna ground plane. The capacitance thus introduced tunes out inductance of the probe. The shape of the teardrop probe is not critical. The probe capacitance required is controlled by the maximum diameter for the teardrop shaped probe, which can be empirically determined for the operating frequency. An aluminum baffle around each subarray blocks out surface wave between subarrays.

Huang, John↗
NASA NTRS1989

Analysis of finite phased arrays of circular microstrip patches

A method is presented for analyzing a finite planar array of circular microstrip patches fed by coaxial probes. The self- and mutual impedances between array elements are calculated using the method of moments with the dyadic Green's function for a dielectric layer on a ground plane. The patch circuits are determined by using the reaction integral equation. The active input impedance as well as the active element pattern of the array are computed from a knowledge of the resultant patch currents. The calculated results for two-element and eight-element linear arrays are in good agreement with experimental data. The active reflection coefficient and element pattern for the center and edge elements of a two-dimensional array as a function of scan angle are also presented.

Deshpande, Manohar D.↗
NASA NTRS1992

Coplanar Waveguide Aperture Coupled Patch Antennas with Ground Plane/Substrate of Finite Extent

Coplanar waveguide (CPW)/aperture coupled microstrip patch antennas constructed with ground coplanar waveguide (GCPW), finite coplanar waveguide (FCPW) and channelized coplanar waveguide (CCPW) are demonstrated. The measured characteristics show that the CCPW/aperture coupled microstrip patch antenna has the largest bandwidth, whereas the GCPW/aperture coupled microstrip patch antenna has the best front-to-back ratio.

Simons, R. N.↗
NASA NTRS1992

Knowledge-based design of generate-and-patch problem solvers that solve global resource assignment problems

We present MENDER, a knowledge based system that implements software design techniques that are specialized to automatically compile generate-and-patch problem solvers that satisfy global resource assignments problems. We provide empirical evidence of the superior performance of generate-and-patch over generate-and-test: even with constrained generation, for a global constraint in the domain of '2D-floorplanning'. For a second constraint in '2D-floorplanning' we show that even when it is possible to incorporate the constraint into a constrained generator, a generate-and-patch problem solver may satisfy the constraint more rapidly. We also briefly summarize how an extended version of our system applies to a constraint in the domain of 'multiprocessor scheduling'.

Voigt, Kerstin↗
NASA NTRS1993

A 10 GHz Y-Ba-Cu-O/GaAs hybrid oscillator proximity coupled to a circular microstrip patch antenna

A 10 GHz hybrid YBCO/GaAs microwave oscillator proximity coupled to a circular microstrip antenna has been designed, fabricated, and characterized. The oscillator was a reflection mode type using a GaAs MESFET as the active element. The feedline, transmission lines, RF chokes, and bias lines were all fabricated from YBCO superconducting thin films on a 1 cm x 1 cm lanthanum aluminate substrate. The output feedline of the oscillator was wire bonded to a superconducting feedline on a second 1 cm x 1 cm lanthanum aluminate substrate, which was in turn proximity coupled to a circular microstrip patch antenna. Antenna patterns from this active patch antenna and the performance of the oscillator measured at 77 K are reported. The oscillator had a maximum output power of 11.5 dBm at 77 K, which corresponded to an efficiency of 10 percent. In addition, the efficiency of the microstrip patch antenna together with its high temperature superconducting feedline was measured from 85 K to 30 K and was found to be 71 percent at 77 K, increasing to a maximum of 87.4 percent at 30 K.

Rohrer, Norman J.↗
NASA NTRS1993

A 10 GHz Y-Ba-Cu-O/GaAs hybrid oscillator proximity coupled to a circular microstrip patch antenna

A 10 GHz hybrid Y-Ba-Cu-O / GaAs microwave oscillator proximity coupled to a circular microstrip antenna was designed, fabricated and characterized. The oscillator was a reflection mode type using a GaAs MESFET as the active element. The feedline, transmission lines, RF chokes, and bias lines were all fabricated from YBa2Cu3O(7-x) superconducting thin films on a 1 cm x 1 cm lanthanum aluminate substrate. The output feedline of the oscillator was wire bonded to a superconducting feedline on a second 1 cm x 1 cm lanthanum aluminate substrate, which was in turn proximity coupled to a circular microstrip patch antenna. Antenna patterns from this active patch antenna and the performance of the oscillator measured at 77 K are reported. The oscillator had a maximum output power of 11.5 dBm at 77 K, which corresponded to an efficiency of 10 percent. In addition, the efficiency of the microstrip patch antenna together with its high temperature superconducting feedline was measured from 85 K to 30 K and was found to be 71 percent at 77 4 increasing to a maximum of 87.4 percent at 30 K.

Rohrer, Norman J.↗
NASA NTRS1993

Modeling polar cap F-region patches using time varying convection

Creation of polar cap F-region patches are simulated for the first time using two independent physical models of the high latitude ionosphere. The patch formation is achieved by temporally varying the magnetospheric electric field (ionospheric convection) input to the models. The imposed convection variations are comparable to changes in the convection that result from changes in the B(y) IMF component for southward IMF. Solar maximum-winter simulations show that simple changes in the convection pattern lead to significant changes in the polar cap plasma structuring. Specifically, in winter, as enhanced dayside plasma convects into the polar cap to form the classic tongue-of-ionization the convection changes produce density structures that are indistinguishable from the observed patches.

Sojka, J. J.↗
NASA NTRS1994

Analysis of cylindrical wrap-around and doubly conformal patch antennas by way of the finite element-artificial absorber method

The goal of this project was to develop analysis codes for computing the scattering and radiation of antennas on cylindrically and doubly conformal platforms. The finite element-boundary integral (FE-BI) method has been shown to accurately model the scattering and radiation of cavity-backed patch antennas. Unfortunately extension of this rigorous technique to coated or doubly curved platforms is cumbersome and inefficient. An alternative approximate approach is to employ an absorbing boundary condition (ABC) for terminating the finite element mesh thus avoiding use of a Green's function. A FE-ABC method is used to calculate the radar cross section (RCS) and radiation pattern of a cavity-backed patch antenna which is recessed within a metallic surface. It is shown that this approach is accurate for RCS and antenna pattern calculations with an ABC surface displaced as little as 0.3 lambda from the cavity aperture. These patch antennas may have a dielectric overlay which may also be modeled with this technique.

Volakis, J. L.↗