Search NASA⌕ Search

SEARCH · Search NASA

Results for “pilot procedures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Piloted Simulation Study of a Dual Thrust-Cutback Procedure for Reducing High-Speed Civil Transport Takeoff Noise Levels

A piloted simulation study was performed for the purpose of indicating the noise reduction benefits and piloting performance that could occur for a typical 4-engine high-Speed Civil Transport (HSCT) configuration during takeoff when a dual thrust-cutback procedure was employed with throttle operation under direct computer control. Two thrust cutbacks were employed with the first cutback performed while the vehicle was accelerating on the run-way and the second cutback performed at a distance farther downrange. Added vehicle performance improvements included the incorporation of high-lift increments into the aerodynamic database of the vehicle and the use of limited engine oversizing. Four single-stream turbine bypass engines that had no noise suppression of any kind were used with this configuration. This approach permitted establishing the additional noise suppression level that was needed to meet Federal Air Regulation Part 36 Stage 3 noise levels for subsonic commercial jet aircraft. Noise level results were calculated with the jet mixing and shock noise modules of the Aircraft Noise Prediction Program (ANOPP).

Riley, Donald R.↗
NASA NTRS1997

Piloted Simulation Tests of Propulsion Control as Backup to Loss of Primary Flight Controls for a B747-400 Jet Transport

Partial failures of aircraft primary flight control systems and structural damages to aircraft during flight have led to catastrophic accidents with subsequent loss of lives (e.g. DC-10, B-747, C-5, B-52, and others). Following the DC-10 accident at Sioux City, Iowa in 1989, the National Transportation Safety Board recommended 'Encourage research and development of backup flight control systems for newly certified wide-body airplanes that utilize an alternate source of motive power separate from that source used for the conventional control system.' This report describes the concept of a propulsion controlled aircraft (PCA), discusses pilot controls, displays, and procedures; and presents the results of a PCA piloted simulation test and evaluation of the B747-400 airplane conducted at NASA Ames Research Center in December, 1996. The purpose of the test was to develop and evaluate propulsion control throughout the full flight envelope of the B747-400 including worst case scenarios of engine failures and out of trim moments. Pilot ratings of PCA performance ranged from adequate to satisfactory. PCA performed well in unusual attitude recoveries at 35,000 ft altitude, performed well in fully coupled ILS approaches, performed well in single engine failures, and performed well at aft cg. PCA performance was primarily limited by out-of-trim moments.

Bull, John↗
NASA NTRS1997

Free Flight and Self-Separation from the Flight Deck Perspective

The concept of "free flight", while still being developed, is intended to emphasize more, flexibility for operators in the National Airspace System (NAS) by providing more separation responsibility to pilots, New technologies, procedures, and concepts have been suggested by the aviation community to enable this task; however, much work needs to be accomplished to help define and evaluate the concept feasibility. The purpose of this simulation was to begin examining some of the communication and procedural issues associated with self-separation in the enroute environment. A simulation demonstration was conducted in the Boeing 747-400 simulator at NASA Ames Research Center. Commercial pilots (from a U.S. domestic carrier) current on the B747-400 aircraft were the participants. Ten flight crews (10 captains, 10 first officers) flew in the Denver enroute airspace environment. A new alerting logic designed to allow for airborne self-separation was created for this demonstration. This logic assumes automatic dependent surveillance broadcast (ADS-B) capability and represented aircraft up to 120 nautical miles on the display. The new flight deck display features were designed and incorporated on the existing navigational display in the simulator to allow for increased traffic and maneuvering information to the flight crew. New tools were also provided to allow the crews to assess conflicts and potential maneuvers before implementing them. Each of the flight crews flew eight different scenarios in the Denver enroute airspace. The scenarios included eight to ten other aircraft, and each scenario was created with the intent of having one of the other aircraft become an operational conflict for our simulator aircraft. Different types of conflict geometries were represented across the eight scenarios. Also, some scenarios allowed for more time to detect a potential clearance, while others allowed for less time for'detection. Additionally, the crews were asked to a ply the Visual Flight Rules (VFR) right of way rules when determining who should maneuver in a conflict situation; therefore, the scenarios were designed to test different applications of those recommendations, Data analyses include an evaluation of crew procedures and communication. The application of the VFR right-of-way rules are being explored. Timing variables are being examined to determine potential efficiency differences between scenarios and conflict types. Proximity of aircraft will be assessed as one indication of the operational safety. The intent of these evaluations is to help provide definitions and guidelines of negotiation procedures in a self-separation environment assuming automated data link technology (ADS-B). Also, definitions of likely flight crew maneuvers and application to current VFR right-of-way rules may be obtained, along with guidelines for negotiation procedures between flight crews.

Lozito, Sandra↗
NASA NTRS1978

Summary report of the Human Factors Committee

Reduced visibility as a human factors problem was studied in terms of the number of lives lost and cost of aircraft accidents and incidents. Human factors in flight through turbulence in detection and avoidance techniques, pilot and crew procedures for handling workloads and distractions caused by turbulence, and aircraft handling techniques for safe flights through turbulence are investigated. Education and training were reviewed in icing problems on aircraft. Pilots failure to recognize and detect wind shear in severe storms is examined. The pilots avoidance of lightning is discussed from the human factors point of view.

Cooper, G. E.↗
NASA NTRS1991

Initial piloted simulation study of geared flap control for tilt-wing V/STOL aircraft

A simulation study of a representative tilt wing transport aircraft was conducted in 1990 on the Ames Vertical Motion Simulator. This simulation is in response to renewed interest in the tilt wing concept for use in future military and civil applications. For past tilt wing concepts, pitch control in hover and low-speed flight has required a tail rotor or reaction jets at the tail. Use of mono cyclic propellers or a geared flap have also been proposed as alternate methods for providing pitch control at low speed. The geared flap is a subject of this current study. This report describes the geared flap concept, the tilt wing aircraft, the simulation model, the simulation facility and experiment setup, the pilots' evaluation tasks and procedures, and the results obtained from the simulation experiment. The pilot evaluations and comments are also documented in the report appendix.

Guerrero, Lourdes M.↗
NASA NTRS1982

The effects of pilot stress factors on handling quality assessments during US/German helicopter agility flight tests

Flight tests were conducted with two helicopters to study and evaluate the effects of helicopter characteristics and pilot and task demands on performance in nap-of-the-Earth flight. Different, low-level slalom courses were set up and were flown by three pilots with different levels of flight experience. A pilot rating questionnaire was used to obtain redundant information and to gain more insight into factors that influence pilot ratings. The flight test setups and procedures are described, and the pilot ratings are summarized and interpreted in close connection with the analyzed test data. Pilot stress is discussed. The influence of demands on the pilot, of the helicopter characteristics, and of other stress factors are outlined with particular emphasis on how these factors affect handling-qualities assessment.

Pausder, H. J.↗
NASA NTRS1983

NASA-FAA helicopter Microwave Landing System curved path flight test

An ongoing series of joint NASA/FAA helicopter Microwave Landing System (MLS) flight tests was conducted at Ames Research Center. This paper deals with tests done from the spring through the fall of 1983. This flight test investigated and developed solutions to the problem of manually flying curved-path and steep glide slope approaches into the terminal area using the MLS and flight director guidance. An MLS-equipped Bell UH-1H helicopter flown by NASA test pilots was used to develop approaches and procedures for flying these approaches. The approaches took the form of Straight-in, U-turn, and S-turn flightpaths with glide slopes of 6 deg, 9 deg, and 12 deg. These procedures were evaluated by 18 pilots from various elements of the helicopter community, flying a total of 221 hooded instrument approaches. Flying these curved path and steep glide slopes was found to be operationally acceptable with flight director guidance using the MLS.

Swenson, H. N.↗
NASA NTRS1982

The effects of pilot stress factors on handling quality assessments during US/German helicopter agility flight tests

Flight tests were conducted with two helicopters to study and evaluate the effects of helicopter characteristics and pilot and task demands on performance in nap-of-the-earth flight. Different, low-level slalom courses were set up and were flown by three pilots with different levels of flight experience. A pilot rating questionnaire was used to obtain redundant information and to gain more insight into factors that influence pilot ratings. The flight test setups and procedures are described, and the pilot ratings are summarized and interpreted in close connection with the analyzed test data. Pilot stress is discussed. The influence of demands on the pilot, of the helicopter characteristics, and of other stress factors are outlined with particular emphasis on how these factors affect handling-qualities assessment. Previously announced in STAR as N83-13114

Pausder, H.-J.↗
NASA NTRS1984

NASA-FAA helicopter Microwave Landing System curved path flight test

An ongoing series of joint NASA/FAA helicopter Microwave Landing System (MLS) flight tests was conducted at Ames Research Center. This paper deals with tests done from the spring through the fall of 1983. This flight test investigated and developed solutions to the problem of manually flying curved-path and steep glide slope approaches into the terminal area using the MLS and flight director guidance. An MLS-equipped Bell UH-1H helicopter flown by NASA test pilots was used to develop approaches and procedures for flying these approaches. The approaches took the form of Straight-in, U-turn, and S-turn flightpaths with glide slopes of 6 deg, 9 deg, and 12 deg. These procedures were evaluated by 18 pilots from various elements of the helicopter community, flying a total of 221 hooded instrument approaches. Flying these curved path and steep glide slopes was found to be operationally acceptable with flight director guidance using the MLS.

Swenson, H. N.↗
NASA NTRS2000

Analysis of Complexity Evolution Management and Human Performance Issues in Commercial Aircraft Automation Systems

Autoflight systems in the current generation of aircraft have been implicated in several recent incidents and accidents. A contributory aspect to these incidents may be the manner in which aircraft transition between differing behaviours or 'modes.' The current state of aircraft automation was investigated and the incremental development of the autoflight system was tracked through a set of aircraft to gain insight into how these systems developed. This process appears to have resulted in a system without a consistent global representation. In order to evaluate and examine autoflight systems, a 'Hybrid Automation Representation' (HAR) was developed. This representation was used to examine several specific problems known to exist in aircraft systems. Cyclomatic complexity is an analysis tool from computer science which counts the number of linearly independent paths through a program graph. This approach was extended to examine autoflight mode transitions modelled with the HAR. A survey was conducted of pilots to identify those autoflight mode transitions which airline pilots find difficult. The transitions identified in this survey were analyzed using cyclomatic complexity to gain insight into the apparent complexity of the autoflight system from the perspective of the pilot. Mode transitions which had been identified as complex by pilots were found to have a high cyclomatic complexity. Further examination was made into a set of specific problems identified in aircraft: the lack of a consistent representation of automation, concern regarding appropriate feedback from the automation, and the implications of physical limitations on the autoflight systems. Mode transitions involved in changing to and leveling at a new altitude were identified across multiple aircraft by numerous pilots. Where possible, evaluation and verification of the behaviour of these autoflight mode transitions was investigated via aircraft-specific high fidelity simulators. Three solution approaches to concerns regarding autoflight systems, and mode transitions in particular, are presented in this thesis. The first is to use training to modify pilot behaviours, or procedures to work around known problems. The second approach is to mitigate problems by enhancing feedback. The third approach is to modify the process by which automation is designed. The Operator Directed Process forces the consideration and creation of an automation model early in the design process for use as the basis of the software specification and training.

Vakil, Sanjay S.↗
NASA NTRS2014

Structural Pain Compensating Flight Control

The problem of control command and maneuver induced structural loads is an important aspect of any control system design. Designers must design the aircraft structure and the control architecture to achieve desired piloted control responses while limiting the imparted structural loads. The classical approach is to build the structure with high margins, restrict control surface commands to known good combinations, and train pilots to follow procedural maneuvering limitations. With recent advances in structural sensing and the continued desire to improve safety and vehicle fuel efficiency, it is both possible and desirable to develop control architectures that enable lighter vehicle weights while maintaining and improving protection against structural damage.

advanced autonomy↗
NASA NTRS2017

Optimal Control Allocation with Load Sensor Feedback for Active Load Suppression, Experiment Development

The problem of control command and maneuver induced structural loads is an important aspect of any control system design. The aircraft structure and the control architecture must be designed to achieve desired piloted control responses while limiting the imparted structural loads. The classical approach is to utilize high structural margins, restrict control surface commands to a limited set of analyzed combinations, and train pilots to follow procedural maneuvering limitations. With recent advances in structural sensing and the continued desire to improve safety and vehicle fuel efficiency, it is both possible and desirable to develop control architectures that enable lighter vehicle weights while maintaining and improving protection against structural damage. An optimal control technique has been explored and shown to achieve desirable vehicle control performance while limiting sensed structural loads. The subject of this paper is the design of the optimal control architecture, and provides the reader with some techniques for tailoring the architecture, along with detailed simulation results.

controls↗
NASA NTRS2017

Optimal Control Allocation with Load Sensor Feedback for Active Load Suppression, Flight-Test Performance

The problem of control command and maneuver induced structural loads is an important aspect of any control system design. The aircraft structure and the control architecture must be designed to achieve desired piloted control responses while limiting the imparted structural loads. The classical approach is to utilize high structural margins, restrict control surface commands to a limited set of analyzed combinations, and train pilots to follow procedural maneuvering limitations. With recent advances in structural sensing and the continued desire to improve safety and vehicle fuel efficiency, it is both possible and desirable to develop control architectures that enable lighter vehicle weights while maintaining and improving protection against structural damage. An optimal control technique has been explored and shown to achieve desirable vehicle control performance while limiting sensed structural loads to specified values. This technique has been implemented and flown on the National Aeronautics and Space Administration Full-scale Advanced Systems Testbed aircraft. The flight tests illustrate that the approach achieves the desired performance and show promising potential benefits. The flights also uncovered some important issues that will need to be addressed for production application.

cFOSS↗
NASA NTRS2018

Development of Possible Go-Around Criteria for Transport Aircraft

This paper adds data to help with the development of possible go-around criteria for transport category aircraft. Presently, airline procedures state that pilots make a go-around decision using multiple criteria at 1000 or 500 ft above the ground, or so-called gates. An experiment conducted on three level-D full-flight simulators investigated the conditions from which pilots cannot successfully recover from an unstable approach and make a normal landing. In addition, pilots' perceptions of risk under these various unstable approach conditions and resulting landings were assessed. Six crews, comprised of a captain and a first officer from the same airline, participated in each simulator. Both the captain and the first officer flew approaches and landings from 55 different initial conditions with varying gate heights, localizer deviations, glideslope deviations, reference-speed deviations, and rate of descents. The initial condition at the starting gate mainly affected longitudinal touchdown deviation and rate of descent at touchdown, with reference-speed deviation having the most significant effect. Results show little difference in touchdown performance for conditions from the 300-ft and 500-ft gates. Conditions at the 100-ft gate introduced significant differences in touchdown performance. Reference-speed and localizer deviation at the starting gate had the strongest influences on perceived risk and go-around decision. In line with other studies, these findings suggest that a 300-ft go-around gate might be acceptable. More research is required to investigate the effects of environmental and runway variables before possible go-around criteria for transport category aircraft can be defined.

GO-AROUNDS↗
NASA NTRS2018

Trusted Communication: Utilizing Speech Communication to Enhance Human-Machine Teaming Success

An area of increasing interest for the next generation of aircraft is autonomy and the integration of increasingly autonomous systems into the national airspace. Such an integration requires humans to work closely with autonomous systems, forming teams. Our hypothesis is that a team composed of both humans and autonomous systems will operate better than either entity alone. We have existing procedures for certifying pilots to operate in the national airspace and are currently working on methods for validating the function of autonomous systems, however we have no method in place for assessing the interaction of these two disparate systems. Communication is one avenue. This paper will examine the use of language as a metric for ascertaining human-machine teaming effectiveness. A proof-of-concept of the application of two communication-based analysis techniques, Linguistic Inquiry and Word Count (LIWC) and Latent Semantic Analysis (LSA), for the prediction of success in human/chatbot teaming was conducted. By running these analyses over data from the 2014 and 2015 Loebner Prize competitions of human/chatbot teaming, numerical scores were obtained that can be associated with scores provided by human judges during the competition. Correlating their LIWC and LSA data with the scores provided by the judges, and using linear regression over this correlation, formulae were obtained that predict the score of human/chatbot interaction. These formulae were tested over the 2013 Loebner Prize transcripts, determining that, though there was strong correlation between predicted and actual scores, the predictive success of this method was not strong. However, with specialized topic spaces and lexica, as well as larger data sets, the predictive power of these metrics will improve. Given the importance of providing metrics for human-machine system team success and given the promise shown by the communication-basedLIWCand LSAmethods, continuing research in this area is necessary. After examining the potential for using communication and spoken language as a metric for the success of human/autonomous system teaming, this paper then examines aspects inherent to communication systems that may contribute to unreliability and reduced trust. Modern natural language processing tools rely on deep learning algorithms to create language rules that produce accurate results, but these rules are uninterpretable. The resulting blackbox system lacks transparency necessary for full validation and complete trust. Additionally, speech-based interfaces pose other difficulties to developing coordinated teamwork between humans and autonomous systems. Human communication is infrequently limited to speech only, instead usually relying on a combination of verbal, gestural, and general body language communication. Reducing an analysis of team effectiveness to a study of spoken language alone is problematic as it leaves these other equally important forms of communication out. This paper will examine these problems and the general deficiencies in speech-based metrics for human-machine teaming.

E L Meszaros↗
NASA NTRS1980

Synthesized voice approach callouts for air transport operations

A flight simulation experiment was performed to determine the effectiveness of synthesized voice approach callouts for air transport operations. Flight deck data was first collected on scheduled air carrier operations to describe existing pilot-not-flying callout procedures in the flight context and to document the types and amounts of other auditory cockpit information during different types of air carrier operations. A flight simulation scenario for a wide-body jet transport airline training simulator was developed in collaboration with a major U.S. air carrier and flown by three-man crews of qualified line pilots as part of their normally scheduled recurrent training. Each crew flew half their approaches using the experimental synthesized voice approach callout system (SYNCALL) and the other half using the company pilot-not-flying approach callout procedures (PNF). Airspeed and sink rate performance was better with the SYNCALL system than with the PNF system for non-precision approaches. For the one-engine approach, for which SYNCALL made inappropriate deviation callouts, airspeed performance was worse with SYNCALL than with PNF. Reliability of normal altitude approach callouts was comparable for PNF on the line and in the simulator and for SYNCALL in the simulator.

Simpson, C. A.↗
NASA NTRS1978

Prediction, evaluation, and specification of flying qualities by means of step target tracking

A new approach to flying qualities specification and evaluation is presented which coordinates current research in the areas of pilot ratings, pilot-aircraft modeling techniques, and simulation and flight test procedures. A time-domain pilot model is described which can model discontinuous and nonlinear pilot behavior in conjunction with completely general time-varying nonlinear aircraft models to simulate discrete maneuvers. This pilot-aircraft model is applied to an existing set of in-flight simulation data, and calculates tracking error and time-on-target statistics for step target tracking that directly relate to the reported pilot comments and ratings. Predicted step target tracking data for eighteen F-5E flight conditions are presented, and the use of the method for control system design is demonstrated using the YF-17.

Onstott, E. D.↗