Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressure plate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1940

Rectangular Shell Plating Under Uniformly Distributed Hydrostatic Pressure

A check of the calculation methods used by Foppl and Henky for investigating the reliability of shell plating under hydrostatic pressure has proved that the formulas yield practical results within the elastic range of the material. Foppl's approximate calculation leaves one on the safe side. It further was found on the basis of the marked ductility of the shell plating under tensile stress that the strength is from 50 to 100 percent higher in the elastic range than expected by either method.

Neubert, M↗
NASA NTRS1957

Effect of Some External Crosswise Stiffeners on the Heat Transfer and Pressure Distribution on a Flat Plate at Mach Numbers of 0.77, 1.39, and 1.98. Coord. No. AF-AM-69

The heat transfer and pressures on the surfaces of several flat-plate models with various external crosswise stiffener arrangements are presented. The tests were made in a free jet at Mach numbers of 0.77, 1.39, and 1.98 for Reynolds numbers of 3 x 10(exp 6), 7 x 10(exp 6), and 14 x 10(exp 6), respectively, based on a length of 1 foot. The addition of external crosswise stiffeners to the flat-plate models caused large pressure and heat-transfer variations on the surfaces of the models.

Carter, Howard S.↗
NASA NTRS1978

Gaussian step-pressure loading of rigid viscoplastic plates

The response of a thin, rigid viscoplastic plate subjected to a spatially axisymmetric Gaussian step pressure impulse loading was studied analytically. A Gaussian pressure distribution in excess of the collapse load was applied to the plate, held constant for a length of time, and then suddenly removed. The plate deforms with monotonically increasing deflections until the dynamic energy is completely dissipated in plastic work. The simply supported plate of uniform thickness obeys the von Mises yield criterion and a generalized constitutive equation for rigid viscoplastic materials. For the small deflection bending response of the plate, the governing system of equations is essentially nonlinear. Transverse shear stress is neglected in the yield condition and rotary inertia in the equations of dynamic equilibrium. A proportional loading technique, known to give excellent approximations of the exact solution for the uniform load case, was used to linearize the problem and to obtain the analytical solutions in the form of eigenvalue expansions. The effects of load concentration, of an order of magnitude change in the viscosity of the plate material, and of load duration were examined while holding the total impulse constant.

Hayduk, R. J.↗
NASA NTRS1980

A correlation method to predict the surface pressure distribution of an infinite plate or a body of revolution from which a jet is issuing

A correlation method to predict pressures induced on an infinite plate by a jet exhausting normal to the plate into a subsonic free stream was extended to jets exhausting at angles to the plate and to jets exhausting normal to the surface of a body revolution. The complete method consisted of an analytical method which models the blockage and entrainment properties of the jet and an empirical correlation which accounts for viscous effects. For the flat plate case, the method was applicable to jet velocity ratios up to ten, jet inclination angles up to 45 deg from the normal, and radial distances up to five diameters from the jet. For the body of revolution case, the method was applicable to a body at zero degrees angle of attack, jet velocity ratios 1.96 and 3.43, circumferential angles around the body up to 25 deg from the jet, axial distances up to seven diameters from the jet, and jet-to-body diameter ratios less than 0.1.

Perkins, S. C., Jr.↗
NASA NTRS1961

Surface Pressures and Heat Transfer on Unswept Blunt Plates in Helium at High Mach Numbers

Pressure distributions and local convective heat-transfer coefficients on a flat plate at zero angle of attack were measured in helium. Data were obtained with various amounts of leading-edge bluntness at Mach numbers of 12.5 and 14.7. The pressures on a sharp leading-edged plate were not influenced by the leading edge and were predicted by the first-order, hypersonic, weak-interaction theory. Pressures on blunt plates were correlated by introducing the leading-edge Reynolds number as a parameter. Measured heat-transfer coefficients on the sharp plate agreed with predictions obtained form existing exact solutions for hear transfer across the laminar boundary layer. For the blunt plates a comparison of theory with experiment indicated that more knowledge of the flow field between the sock wave and plate surface is necessary before an adequate prediction of convective heat transfer can be made. Shock-wave shapes for the blun plates at a Mach number 12.5 and zero angle of attack were measured. At distances between 2 and 60 leading-edge thicknesses from the shock vertex, the shock-wave shapes were found to be represented by a modified form of the blast-wave analogy.

Marvin, Joseph G.↗
NASA NTRS1991

Forces and pressures induced on circular plates by a single lifting jet in ground effect

NASA Ames is conducting a program to develop improved methods for predicting suckdown and hot-gas ingestion on jet V/STOL aircraft when they are in ground effect. As part of that program a data base is being created that provides a systematic variation of parameters so that current empirical prediction procedures can be modified. The first series of tests in this program is complete. This report is one of three that presents the data obtained from tests conducted at Lockheed Aeronautical Systems - Rye Canyon Facility and the High Bay area of the 40 by 80 foot Wind Tunnel at Ames Research Center. Suckdown on two circular plates is examined.

Bellavia, David C.↗
NASA NTRS1974

Effects of flanges on pressure distribution on a flat plate and on a corrugated surface at Mach numbers from 0.60 to 1.97

An 8 by 6 foot supersonic wind tunnel was used to obtain the static pressure distribution on a plate in the region of a flange placed normal to the airstream. Tests were conducted on both a flat plate surface and a corrugated surface using flange heights ranging from 10 to 125 percent of the boundary layer height. Data were obtained at a zero degree angle-of-attack and at Mach numbers from 0.60 to 1.97.

Johns, A. L.↗
NASA NTRS1942

Square plate with clamped edges under normal pressure producing large deflections

A theoretical analysis is given for the stresses and deflections of a square plate with clamped edges under normal pressure producing large deflections. Values of the bending stress and membrane stress at the center of the plate and at the midpoint of the edge are given for center deflections up to 1.9 times the plate thickness. The shape of the deflected surface is given for low pressures and for the highest pressure considered. Convergence of the solution is considered and it is estimated that the possible error is less than 2 percent. The results are compared with the only previous approximate analysis known to the author and agree within 5 percent. They are also shown to compare favorably with the known exact solutions for the long rectangular plate and the circular plate.

PLATES-PRESSURE↗
NASA NTRS1991

High Reliability Robot Friendly ORU Interface

Presented here is a robot friendly coupling device for an orbital replacement unit (ORU). The invention will provide a coupling that is detached and attached remotely by a robot. The design of the coupling must allow for slight misalignments, over-torque protection, and precision placement. This is accomplished by means of a triangular interface comprising three components. A base plate assembly is located on an attachment surface, such as a satellite. The base plate assembly has a cup member, a slotted member, and a post member. The ORU that the robot attaches to the base plate assembly has an ORU plate assembly with two cone members and a post member which mate to the base plate assembly. As the two plates approach one another, one cone member of the ORU plate assembly has to be placed accurately enough to fall into the cup member of the base plate assembly. The cup member forces alignment until a second cone falls into a slotted member which provides final alignment. A single bolt is used to attach the two plates. Two deflecting plates are attached to the backs of the plates. When pressure is applied to the center of the deflecting plates, the force is distributed preventing the ORU and base plates from deflecting. This accounts for precision in the placement of the article. The novelty is believed to reside in using deflecting plates in conjunction with kinematic mounts to provide distributed forces to the two members.

Voellmer, George M.↗
NASA NTRS1992

High-Repeatability, Robot Friendly, ORU Interface

A robot-friendly coupling device for an Orbital Replacement Unit (ORU). The invention will provide a coupling that is detached and attached remotely by a robot. The design of the coupling must allow for slight misalignments, over torque protection, and precision placement. This is accomplished by using of a triangular interface having three components. A base plate assembly is located on an attachment surface, such as a satellite. The base plate assembly has a cup member, a slotted member, and a post member. The ORU that the robot attaches to the base plate assembly has an ORU plate assembly with two cone members and a post member which mate to the base plate assembly. As the two plates approach one another, one cone member of the ORU plate assembly only has to be placed accurately enough to fall into the cup member of the base plate assembly. The cup forces alignment until a second cone falls into a slotted member which provides final alignment. A single bolt is used to attach the two plates. Two deflecting plates are attached to the backs of the plates. When pressure is applied to the center of the deflecting plates, the force is distributed preventing the ORU & base plates from deflecting. This accounts for precision in the placement of the article.

Voellmer, George M.↗
NASA NTRS2021

Numerical Simulation of Pressure-induced Separation of Turbulent Flat-plate Boundary Layers: Definition and Overview of New Cases with Suction-only Transpiration and a Step in Reynolds Number

Results from two new direct numerical simulations (DNSs) are added to the database described in Coleman, Rumsey & Spalart (2018) (henceforth CRS18), and available at the NASA TMR website (https://turbmodels.larc.nasa.gov). The new flows, Cases D and E, are similar to the earlier ones (Cases A–C) in that a transpiration profile above a flat plate creates a prolonged adverse pressure gradient (APG) that drives a canonical turbulent zero-pressure-gradient (ZPG), flat-plate boundary layer towards separation; they differ in that for the new cases (1) the APG is not followed by a favorable gradient (FPG), since only suction transpiration is employed, and (2) the mean shear stress does not cross zero, so that the width of the mean bubble, strictly defined, is essentially zero. However, the probability of reversed skin friction exceeds 49%. The motivation was to produce a flow that is more akin to technological flows, including shock-boundary-layer interaction, with a gradual turbulence-controlled recovery. One of the new simulations is also at a significantly higher Reynolds number than the earlier flows.

Turbulence↗