Search NASA⌕ Search

SEARCH · Search NASA

Results for “pressure plate”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Design and Analysis of 10” Parallel Plate Relief Device

All Cryomodule (CM) and Cryogenic Distribution System (CDS) relieving into Helium Low Pressure (LP) return header, which is connected to compressor suction so, helium can be preserved during small flow relieving event and recirculated to system. However, during worst case scenario, Helium LP header requires a parallel plate relief device to relieve excess pressure from header. To complete the CDS Warm piping header, a new design for a 10 parallel plate relief device is necessary to relieve outside of the tunnel into atmosphere.

Chicas, Kelly↗
DOE OSTI2025

Development of a thermal creep model for aluminum alloy 6061 cladding in U-10Mo monolithic fuel plates

Plate-type fuel elements consisting of a high-density, low-enriched uranium (LEU) U–10Mo-based fuel foil encapsulated in an aluminum alloy (AA) cladding are fabricated using the hot isostatic pressing (HIP) technique. During the HIP process, the fuel plate system is heated to 560 °C, then cooled to room temperature. This heat cycle significantly affects the mechanical properties of the aluminum cladding, and experimental investigations have shown that, post-HIP bonding, the mechanical properties of the aluminum cladding transition from those of AA 6061-T6 to something closer to the O temper. More specifically, the ultimate strength of the cladding decreases while its ductility increases, making it challenging to capture the changes in mechanical behavior and material properties. Understanding the residual stresses generated during the HIP process is critical for assessing the fuel plate’s integrity under various temperature, pressure, and irradiation. To simulate the HIP bonding process, the elastic, plastic, and thermal properties of the cladding are assumed to be similar to those of AA 6061-O temper. However, the primary challenge lies in the lack of available data for the creep model of the AA 6061 cladding during this transient process of HIP. The present study focuses on developing a computational model that predicts the creep behavior of the aluminum cladding in the fuel plates during the HIP process, as cladding creep significantly influences the residual stresses generated in U-10Mo fuel plates during HIP fabrication. Furthermore, as HIP bonding occurs at high temperatures that are nearing the melting point of aluminum, the present work considered a temperature-dependent Arrhenius-type creep model. In particular, a hyperbolic sine creep model is employed to estimate the creep properties of the as-fabricated aluminum cladding. In conclusion, the residual stresses predicted in the U-10Mo fuel when using the newly calibrated creep model closely align with the experimental measurements, validating the model’s accuracy.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Effect of neutron beamline irradiation on hydrogen equilibrium vapor pressure over hydrided Zircaloy-4

Here, the effect of neutron irradiation on the hydrogen equilibrium vapor pressure over hydrided samples of nickel-plated Zircaloy-4 was evaluated at the Washington State University Research Reactor’s epithermal beamline facility. To enable this study, a measurement capability was designed and assembled to obtain low pressure (<0.1 Pa) measurements over the temperature range of interest (i.e., ~300° - 400°C). Measurement results were in good agreement with tends extrapolated from previous data obtained at higher temperatures as well as recent thermodynamic data. No irradiation enhancement of vapor pressure was observed under the incident flux of epithermal neutrons over this temperature range.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Comparison of Planar and Tubular Flow Field Plates for Proton Exchange Membrane Fuel Cells (PEMFCs) through Simulation

Proton exchange membrane fuel cells are excellent clean energy alternatives to current non-renewable energy sources. Bipolar plates are a key component of these fuel cells and directly responsible for their performance. Traditional bipolar plates are created in a planar form, but recent research has revealed a novel tubular design that performs similarly to conventional plates. Here, this study compares traditional planar designs with tubular ones. The finite element ANSYS software was used to determine and visualize velocity and pressure distributions of fluid flow through the bipolar plate channels.

25 ENERGY STORAGE↗
DOE OSTI2020

Fabricating and Testing Additively Manufactured Components for Tritium Service Consideration

This SRTE PDRD sponsored project produced test articles, tooling, and training articles for evaluation. In addition, the hydrogen compatibility of the alloys that can be readily produced by the Arcam A2X was tested. During the evaluation it was determined that the mechanical properties were more sensitive to build plate location than hydrogen exposure. Hydrogen pressure – volume-temperature experiments showed that the as-fabricated samples did not absorb hydrogen readily, but activated samples did.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Development of a Particle Flow Control Mechanism

The next generation of Concentrated Solar Power (CSP) systems are utilizing solid particles as the heat transfer medium. The state-of-the-art particle flow control mechanism currently utilized is the slide-gate mechanism which functions by linearly actuating a gate across a tear-drop shaped opening. The sensitivity, which is a measure of the change in mass flow rate per unit movement of the slide-gate, is 0.354 g/s-mm[1]. The slide-gate’s main shortcomings include particle lodging and particle leakage between the plates, and difficulty actuating under the pressure from the particles. The goal of a new device is to minimize or eliminate these flaws. The new proposed device functions similar to a chuck mechanism in a drill where a rotation of an outer ring produces a change in outlet area through moving “jaws” diagonally. This mechanism aims to solve the issues of the slide-gate by having the jaws on the outside of the particle flow volume to reduce the probability of particle lodging, and the jaw tips are designed to overlap as they actuate to reduce particle leakage. Additionally, the vertical orientation of the device as well as the inclined movement of the jaws allows for easier actuation of the device under pressure. Experiments involving 3D printed prototypes have been carried out, producing a max mass flowrate of about 50 g/s and a sensitivity curve with the equation 𝑦 (𝑔/𝑠) = 0.0851𝑥^2(𝑔/𝑠−𝑚𝑚2) +3.6993𝑥(𝑔/𝑠−𝑚𝑚). These experiments validated the device’s capability to address the shortcomings of the slide-gate. Currently, an aluminum model of the device is being tested at room temperature, and a stainless-steel model is being developed to be tested at 700oC, which is the expected operating temperature of the CSP system. Furthermore, simulations are on-going to predict the mass flowrate of different device configurations at room and high temperatures.

14 SOLAR ENERGY↗
DOE OSTI2023

Electric Field Measurements to Investigate Sheath Formation in a Nanosecond Pulsed Discharge

The objective of the research was to study the temporally and spatially resolved dynamics of sheath formation in a nanosecond pulsed plasma generated in a parallel plate electrode geometry at near atmospheric pressures. We have performed LIF dip measurements at the Sandia Low-Temperature Plasma Research Facility showing the capability to measure electric fields in near atmospheric pressure plasmas although with insufficient spatial resolution near the electrodes. Stark polarization spectroscopy implemented at the University of Minnesota was shown to be able to probe the formation of the sheaths in nanosecond pulsed plasmas. Within 30 ns, a reduction of the sheath thickness to about 250 μm is observed, coinciding with a gradual increase of the discharge current and proportional increase in electric field at the cathode. The electric field evolution as obtained by the fluid model is in excellent agreement with the measurements and shows that an enhanced ionization near the cathode is causing the space charge formation responsible for the increase in electric field. High resolution Stark polarization spectroscopy showed sheaths with dimensions of the order of 50 μm underlining the need of micrometer spatial resolution for sheath characterization in near atmospheric pressure.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Flow maldistribution in plate heat exchangers – Impact, analysis, and solutions

Plate heat exchangers are commonly used in various industrial applications, such as refrigeration, air conditioning, heat pumps, powerplants, and chemical industries. Plate heat exchangers are well known for their superior heat transfer performance, compactness, and low refrigerant charge. Despite offering several advantages, they suffer from flow maldistribution issues. The flow maldistribution can deteriorate both the heat transfer and pressure drop performance, ultimately resulting in a lower system efficiency where plate heat exchangers are deployed. The flow maldistribution issues become more pronounced when the heat exchanger size is relatively large and the number of plates is higher, limiting the deployment of plate heat exchangers in larger industrial systems. Consequently, analyzing and understanding the flow maldistribution behavior in plate heat exchangers and finding ways to mitigate flow maldistribution related issues become essential topics of interest. Further, this review aims to address the effect of flow maldistribution on plate heat exchanger characteristics. First, the experimental and numerical works on flow maldistribution under single-phase and two-phase conditions are detailed. Subsequently, the end-channel and end-plate effects are discussed. Then, the methods to mitigate flow maldistribution in plate heat exchangers are outlined. Finally, based on a thorough literature survey and industrial requirements, future research directions are recommended.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Mechanical Properties of Aged A709

A709 plate is in the process of being developed and qualified through a collaboration by Argonne National Laboratory (ANL), Idaho National Laboratory (INL), and Oak Ridge National Laboratory (ORNL). The goal is to qualify A709 plate in Section III, Division 5 of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Code (BPVC). This would permit the construction of A709 plate for fast-reactor structural applications. A tradeoff between creep and creep-fatigue properties was established in prior work. A processing route was identified as providing the optimal balance between creep-rupture and elevated-temperature cyclic properties for the solution annealed condition. This condition, however, resulted in a shorter than desired creep-rupture life. Aging is probed to evaluate its potential at further improving mechanical properties. Aging statically precipitates the solutes in solution prior to service. The processing routes identified as providing the best creep-rupture properties and best balance in mechanical properties are investigated. This report discloses the results from tensile, creep, and elevated-temperature cyclic testing performed at INL on the aged material. The aged properties are compared to solution annealed properties. A709 offers improvement in performance compared to 316H particularly at high temperatures; 316H is a material qualified in Section III, Division 5 of the ASME BPVC. For certain high-temperature fast-reactor design conditions, 316H cannot be used while A709 can.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Mechanical seal with high pressure high temperature secondary seal

A secondary seal of a mechanical seal comprises an annular sealing gasket and backing plate surrounding a cylindrical sealing surface, all of which can be made of the same metallic material. The gasket is C-shaped in cross section, and is axially pressed during operation into a C-shaped groove formed in the backing plate, the groove being shallower and larger in inner diameter than the gasket, so that the gasket, when pressed into the groove, deforms radially inward and seals against both the backing plate and the sealing surface. The contact area between the gasket and sealing surface increases with pressure. In embodiments, when the pressure is released, the gasket retracts from the sealing surface, allowing easy disassembly and allowing axial movement of the gasket and backing plate. Highly polished surfaces of the gasket and sealing surface can allow axial motion thereof during operation to maintain the seal face gap.

42 ENGINEERING↗
DOE OSTI2024

Rate-induced aging effects on Parallel-Plate Avalanche Counter (PPAC) caused by heavy ion beams

The Facility for Rare Isotope Beams (FRIB) is one of the premier scientific user facilities for nuclear science with radioactive beams, capable of producing most (approximately 80%) of the isotopes expected to exist, from oxygen to uranium, at energies up to 200 MeV/u. With the increase in beam power from the present 10 kW to the planned 400 kW, FRIB experiments are about to enter a new era. An unprecedented rate capability as well as stable performance of all the planned instrumentation intended for beam diagnostics and beam tuning is required at the expected high beam intensities (> 1 MHz). A summary of aging phenomena at high heavy-ion beam rates observed in the Advanced Rare Isotope Separator (ARIS) detectors for beam diagnostics, including Parallel Plate Avalanche Counters (PPAC) and plastic scintillation for time-of-flight measurements, is discussed. Current research and development project to mitigate rate-induced aging are presented.

Aging effects↗
DOE OSTI2020

Workshop to Plan R&D Support of Fuel/Basket Modification for Direct Disposal of Future DPCs

By 2030 about half of all spent nuclear fuel (SNF) arising from the current fleet of commercial power plants will be in dual-purpose canisters (DPCs), which are designed for storage and transportation but not for disposal. As an alternative to complete repackaging of the fuel for disposal, considerable cost savings and lower worker dose could be realized by directly disposing of this SNF in DPCs. The principal technical consideration is criticality control in a geologic repository, because the DPCs are large and depend on neutron absorbing basket components for criticality control. Neutron absorbing materials are generally aluminum-based, and under disposal conditions can degrade after a few hundred years contact with ground water. Simple modifications to the SNF assemblies or the DPC baskets could help to achieve direct disposal, and this is one of the approaches being studied to address the possibility of disposal criticality (SNL 2020a). Five fuel/basket modification concepts have been proposed (SNL 2020b) and a virtual workshop was conducted to solicit review and feedback on these concepts. The proposed solutions are: 1) zone loading of DPCs to limit reactivity, 2) replacing absorber plates with advanced neutron absorbing (ANA) material, 3) adding disposal control rods to pressurized water reactor (PWR) assemblies, 4) rechanneling boiling water reactor (BWR) assemblies with ANA material, and 5) basket insert plates (chevron inserts) made from ANA material. The presentations from the workshop are provided in this report, and the workshop discussions are summarized. This information includes prioritization of the proposed fuel/basket modification solutions, and prioritization of the associated model development, validation testing, and quality assurance activities. Information documented in this report will help to steer research and development efforts at Sandia National Laboratories, Oak Ridge National Laboratory, and Idaho National Laboratory that support the U.S. Department of Energy, Office of Nuclear Energy, Spent Fuel and Waste Science and Technology program

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Fluid-phase helium: Shock-compression experiments, quantum molecular dynamics simulations, and development of an equation of state

Helium (He) plays a critical role in numerous areas ranging from the study of celestial objects like brown dwarfs and gas giants to modern-day technologies like nuclear energy and rocket propulsion. For many of these applications, it is essential to have a reliable equation of state (EOS) for He that yields an accurate representation of its thermodynamic behavior. To help constrain and develop such EOS models, we have performed a series of shock-compression experiments on cryogenic liquid He to pressures exceeding 100 GPa using a magnetically accelerated flyer plate on Sandia National Laboratories' Z-machine. We have also performed quantum molecular dynamics simulations that are consistent with our shock measurements. None of the previously available EOSs agree with our experimental and simulation results, motivating the development of a fluid-phase He EOS that we present in this study. Here, we show that our EOS yields good agreement with published data that span temperatures and pressures encountered across a diverse array of applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Shock Initiation Microscopy with High Time and Space Resolution

In this paper, we describe studies of shock initiation and shock-to-detonation transitions in energetic materials using a tabletop shock compression microscope with nanosecond time resolution and micrometer spatial resolution. Planar input shocks with durations of 4–20 ns are produced using 0–4.5 km/s laser-launched flyer plates. Emphasis is on measurements of temperature, velocities, pressure, and microstructure using photon Doppler velocimetry (PDV), optical pyrometry and high-speed videography. Techniques are discussed for fabricating disposable shock target arrays of tiny plastic-bonded explosives (PBX), liquid and powder explosives, and single-crystal explosives for high-throughput studies. Optical temperature measurements of shocked triaminotrinitrobenzene (TATB) are discussed. Since TATB is yellow, we developed methods to correct for the blue absorption to obtain more accurate temperatures. Hot spots in shocked polymer-encased HMX (octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine) crystals are observed in real-time, showing a hot spot produced in a collapsing void that ignites a deflagration. Despite the small dimensions of our explosive charges (typically 1 mm diameter and 250 μm length), we produced reproducible detonation states in solid and liquid explosives using short-duration shocks near the von Neumann spike (VNS) pressure. We show the VNS pressure is associated with a transition to high-efficiency gas production from the explosives. In studies of NM, prior to detonation, we see reaction originating at hot spots which coalesce to form a superdetonation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Parameter estimation from spontaneous imbibition into volcanic tuff

Two-phase fluid flow properties underlie quantitative prediction of water and gas movement, but constraining these properties typically requires multiple time-consuming laboratory methods. The estimation of two-phase flow properties (van Genuchten parameters, porosity, and intrinsic permeability) is illustrated in cores of vitric nonwelded volcanic tuff using Bayesian parameter estimation that fits numerical models to observations from spontaneous imbibition experiments. The uniqueness and correlation of the estimated parameters is explored using different modeling assumptions and subsets of the observed data. The resulting estimation process is sensitive to both moisture retention and relative permeability functions, thereby offering a comprehensive method for constraining both functions. The data collected during this relatively simple laboratory experiment, used in conjunction with a numerical model and a global optimizer, result in a viable approach for augmenting more traditional capillary pressure data obtained from hanging water column, membrane plate extractor, or mercury intrusion methods. This method may be useful when imbibition rather than drainage parameters are sought, when larger samples (e.g., including heterogeneity or fractures) need to be tested that cannot be accommodated in more traditional methods, or when in educational laboratory settings.

58 GEOSCIENCES↗
DOE OSTI2022

University of Missouri Research Reactor (MURR) Design Demonstration Element End Fitting Structural Rigidity Analysis

The primary objective of this work is to assess the extent to which the stiffness (measured by means of maximum displacement) of the end fittings in the DDE contributes to the stiffness of the entire element, and how it compares to the equivalent stiffness of the end fittings in the LEU element. Structural analysis of both the LEU element and the DDE were performed using COMSOL 5.3a finite element software. Supporting combs are used on the leading and trailing edges of fuel plates for both the LEU element and the DDE. Therefore, simulations with and without combs are performed as two bounding boundary conditions on the leading edge of the fuel plates. Three types of loads are analyzed in this work: the hydraulic load due to the channel flow disparity-induced pressure differential, the thermal load due to the thermal expansion of the fuel plates, and a point load equal in magnitude to the LEU element’s weight.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Design of a 2 MW ZrC/W-based molten-salt-to-sCO 2 PCHE for concentrated solar power

To increase the power cycle efficiency and lower the levelized cost of electricity (LCOE) of concentrated solar power (CSP) plants, printed circuit heat exchangers (PCHEs) capable of operating above 700 °C with molten chloride salt and a sCO 2 -based fluid are needed. In this paper, the design of a high-pressure, high-temperature, 2 MW PCHE comprised of a thermomechanically-robust, zirconium carbide/tungsten (ZrC/W) composite is conducted for CSP plants. The ZrC/W composite is a material with high thermal conductivity, high stiffness, and high failure strength at high temperatures, along with excellent resistance to thermal cycling and thermal shock. In this work, a thermomechanical design analysis was conducted to select appropriate material thicknesses of the ZrC/W plates, and to determine the geometrical dimensions and the thermal performance of the PCHE. The influences of the plate number and heat exchanger length on power density and pressure drop have also been systematically investigated. Economic analyses were conducted to compare the cost of ZrC/W-based PCHEs to those comprised of IN740H (a state-of-the-art, nickel-based superalloy) and 316 stainless steel (316SS). Finally, at a sufficiently high plate production rate, the manufacturing cost of ZrC/W-based PCHEs can be significantly lower, while achieving a much higher power density, compared with state-of-the-art, nickel alloy-based and stainless steel-based PCHEs.

14 SOLAR ENERGY↗
DOE OSTI2024

Transducer Resolution Effect on Pressure Fluctuations Beneath Hypersonic Turbulent Boundary Layers

The size of a pressure transducer is known to affect the accuracy of measurements of wall-pressure fluctuations beneath a turbulent boundary layer because of spatial averaging over the sensing area of the transducer. In this paper, the effect of finite transducer size is investigated by applying spatial averaging or wavenumber filters to a database of hypersonic wall pressure generated from a direct numerical simulation (DNS) that simulates the turbulent portion of the boundary layer over a sharp 7° half-angle cone at nominally Mach 8. Here, a good comparison between the DNS and the experiment in the Sandia Hypersonic Wind Tunnel at Mach 8 is achieved after spatial averaging is applied to the DNS data over an area similar to the sensing area of the transducer. The study shows that a finite sensor size similar to that of the PCB132 transducer can cause significant attenuation in the root-mean-square and power spectral density (PSD) of wall-pressure fluctuations, and the attenuation effect is identical between cone and flat plate configurations at the same friction Reynolds number. The Corcos theory is found to successfully compensate for the attenuated high-frequency components of the wall-pressure PSD.

42 ENGINEERING↗