Search NASA⌕ Search

SEARCH · Search NASA

Results for “random microstructure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Effect of build geometry on the microstructural development of 316L parts produced by additive manufacturing

Highlights: • Stainless steel ribs were created via direct metal laser sintering to investigate microstructural effect of part design. • EBSD confirmed the presence of large elongated grains in the center of the part, with preferred orientation. • Small grains at the rib surface were found to grow towards the center of the rib with random orientation. • By changing rib thickness and build angle varying texture was observed in the final products. • Large intragranular misorientations were observed in all samples. - Abstract: Additive manufacturing (AM) technology has shown great potential in manufacturing complex products, such as lattice structures without extensive tooling. The focus of this study was to understand the effect of the part geometry on the resulting microstructure. Direct metal laser sintering was used for fabrication of ribs with thicknesses varying between 0.2 and 3.0 mm as well as inclined ribs the with build angles of 30° and 45°. The investigation showed that grains were growing in an epitaxial manner parallel to the building direction. The large elongated grains had a preferential orientation, resulting from the temperature gradient. Additionally, it was found that small grains had formed close to the part surface which were inclined towards the center of the rib. In contrast to the elongated grains, they had a random orientations. The results also indicated that at build angles below 45°, the formed microstructure consisted of the large grains elongated in the building direction. For the used process parameters, the critical part thickness to avoid large elongated grains was found to be about 0.4 mm. These findings allowed us to establish the basics for design rules when it comes to thin wall structures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Hot Forging Options for Thick Castings

Uranium alloyed with 10 wt% molybdenum (U-10Mo) is a monolithic nuclear fuel relevant to the National Nuclear Security Administration’s nonproliferation efforts. Research has been underway to optimize processing techniques for the U-10Mo fuel. This study investigated the use of hot compression or “hot forging” on a thick (~1") cast and homogenized U-10Mo plate before standard hot and cold rolling procedures. After plates were cast and homogenized, six samples were cut and forged at 700°C at a strain rate of either 0.10 s –1 or 0.01 s –1 at six levels of reduction. After forging, all samples underwent hot and cold rolling followed by annealing to achieve a final foil thickness of about 0.0085". Samples were taken at each stage of the casting and thermomechanical processing to assess the microstructural evolution. Chemical composition, microstructure, and uranium carbide morphology are presented and assessed in this study. Upon hot forging, dislocations accumulate along the grain boundaries, which serve as nucleation sites for randomly oriented, strain-free grains during subsequent annealing steps. Hot forging and subsequent annealing produced very heterogeneous grain sizes. However, no molybdenum segregation was observed after forging. No obvious trend was observed between forging conditions (strain rate and reduction percentage) and the microstructure after final thermomechanical processing. Upon hot rolling to 0.04" and annealing (700°C for 45 min), the average grain diameters from OM was 17 ± 2 µm across the six different forged samples. The subsequent cold rolling to 0.0085" and then annealing (700°C for 45 min) resulted in an average of 13 ± 2 µm between the six samples. Thus, the starting, as-forged microstructure did not appear to significantly influence the final microstructure of the cold-rolled foil. These results will help with understanding and expanding hot working capabilities for thicker U-10Mo castings. They also provide useful information on the effects of hot forging and its potential use to minimize defects that can arise during subsequent hot and cold rolling procedures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2018

Complete Status Report Documenting the Development of Friction Stir Welding for Producing a Butt Joint in Thin Wall Tubing of ODS Alloys

A challenging attempt using friction stir welding to produce a butt joint between two 1.0 mm thick plates of 14YWT was nearly successful. The modified tool pin mostly penetrated the thickness of the adjoined thin plate samples resulting in a small blunt notch on the bottom surface of the butt joint. A bend occurred in the thin plate sample due to formation of stresses from clamping the thin plate sample during FSW. The peak displacement of the bend occurred along the center line of the butt joint. The weld zone showed good microstructure mixing with some flashing mostly on the retreating side that suggested excess heat input by friction between the traveling and spinning tool pin and thin plates of 14YWT. Neutron diffraction experiments were performed on the bent sample of 14YWT to measure the residual stresses in the butt joint on the HB-2B beam line at the Neutron Residual Stress Facility at HFIR. However, the neutron scattering to background noise ratio was very low during data acquisition. Measurements of lattice strains were obtained in the rolling (RD) and normal (ND) directions but not in the extrusion direction (ED) of the thin plate sample. Unfortunately, the quality of the data was not sufficient for determining the residual stresses in the butt joint. From the previous neutron scattering experiments conducted on four hot rolled plates (R1, R2, R3 and R4) of 14YWT, the residual stresses were calculated from lattice strain data and plotted in 2-D color contour maps for ED, RD and ND. The results showed variations in the magnitude and spatial position of residual stresses in the microstructure of the four plates. The magnitude in residual stresses in ED and RD increased gradually with increasing rolling deformation for R1 (50%) to R2 (76%), followed by larger increases in R3 (89%) and R4 (95%). The maximum peaks in residual stresses for R4 was ~710-730 MPa in ED and RD. The residual stresses in ND were below ~300 MPa for each of the 4 rolled plates, with a maximum residual stress in R4 (95%) of ~400 MPa. These results indicated that significant residual stresses representing ~57% of the yield stress of 14YWT (SM13) had accumulated in the 14YWT plate after hot rolling to the 1 mm thickness, which was used in the FSW experiments. The microstructure analysis of the 1.0 mm thick plate of 14YWT containing the butt joint produced by FSW revealed significant changes in the grain structure and texture between the unaffected zone (UZ) of the rolled plate and the butt joint weld. In the UZ, the grains were severely elongated after 95% deformation and mainly possessed the {101} texture component in the ED. Two predominant grain misorientation angles were observed: one consisting of small misorientations of <5º between highly elongated grains and the other consisting of large misorientations of >15º in pockets of small grains that might have formed by dynamic recrystallization processes during rolling of the plate at 1000ºC. The morphology and texture of grains in the heat affected zone (HAZ) were similar to those in UZ, except the grains had coarsened due to excess heat input during FSZ. A population of pores formed and the grains both coarsened and changed to isotropic morphology in the microstructure of the butt joint on both the advancing and retreating sides. The texture of grains in both regions were randomly orientated between the 3 poles {001}, {101} and {111}. The main difference in texture of grains between the advancing side and retreating side was with the misorientation angles of neighboring grains. Most of the grains in the advancing side had misorientation angles of >5º indicating that these grains experienced recrystallization. On the retreating side, areas containing larger grains showed high misorientation angles of >15º compared to areas appearing as bands of grains with misorientation angles of <5º and between 5º-15º. Numerous small pockets of grains with low misorientation angles of <5º were distributed in the microstructure among the grains showing high misorientation angles of >15º. It was determined that the grains associated with low misorientation angles contained sub-grain structures, which was consistent with both recrystallization and recovery mechanisms for grains located on the retreating side of the butt joint. These results demonstrate the complex microstructure that evolves in the microstructure of 14YWT resulting from the input of high temperatures and severe deformations during FSW.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Minimizing thickness variation in monolithic U-10Mo fuel foil and Zr interlayer during hot rolling: A microstructure-based finite element method analysis

Low-enriched uranium alloyed with 10 wt. % molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium fuel for the United States’ high performance research reactors. The monolithic U-10Mo fuel plate consists of a metallic U-10Mo fuel foil with a 25 µm Zr interlayer and a relatively thick cladding of aluminum alloy 6061. The Zr interlayer is typically applied during the hot co-rolling process, and this process dictates the uniformity of the Zr interlayer. Thickness variation observed in the U-10Mo and Zr interlayer has been attributed to several sources: the initial grain size of the U-10Mo castings, can materials, rolling temperature, inhomogeneous molybdenum content, and porosity in the cast U-10Mo. This thickness variation limits the ability to meet the dimensional specification; thus, a better understanding of the factors causing the nonuniform thickness is needed. In this work, we used a novel, microstructure-based finite element method to model the hot rolling process to address these concerns. Grain microstructures in U-10Mo were tessellated and explicitly considered in the finite element model. Each grain was assigned a random material property to mimic the grain strength variations induced by different grain orientations. Simulations were performed using six steel can thicknesses, four grain sizes, and with or without a Zr interlayer to investigate the influences of those variables on the thickness nonuniformity. The simulation results showed that a thinner steel can and finer U-10Mo grain size reduce thickness variations in both the U-10Mo fuel foil and Zr interlayer. The direct findings from the simulations and analysis can be used to optimize the hot rolling schedule, reduce fabrication defects, and meet the dimensional specifications. The proposed microstructure-based finite element model can be also coupled with experimental microstructure characterization data, images, and models to simulate multi-pass hot rolling.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Novel pore size-controlled, susceptibility matched, 3D-printed MRI phantoms

We report the design concept and fabrication of MRI phantoms, containing blocks of aligned microcapillaires that can be stacked into larger arrays to construct diameter distribution phantoms or fractured, to create a “powder-averaged” emulsion of randomly oriented blocks for vetting or calibrating advanced MRI methods, that is, diffusion tensor imaging, AxCaliber MRI, MAP-MRI, and multiple pulsed field gradient or double diffusion-encoded microstructure imaging methods. The goal was to create a susceptibility-matched microscopically anisotropic but macroscopically isotropic phantom with a ground truth diameter that could be used to vet advanced diffusion methods for diameter determination in fibrous tissues. Two-photon polymerization, a novel three-dimensional printing method is used to fabricate blocks of capillaries. Double diffusion encoding methods were employed and analyzed to estimate the expected MRI diameter. Susceptibility-matched microcapillary blocks or modules that can be assembled into large-scale MRI phantoms have been fabricated and measured using advanced diffusion methods, resulting in microscopic anisotropy and random orientation. This phantom can vet and calibrate various advanced MRI methods and multiple pulsed field gradient or diffusion-encoded microstructure imaging methods. We demonstrated that two double diffusion encoding methods underestimated the ground truth diameter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Strong yet ductile nanolamellar high-entropy alloys by additive manufacturing

Additive manufacturing produces net-shaped components layer by layer for engineering applications. The additive manufacture of metal alloys by laser powder bed fusion (L-PBF) involves large temperature gradients and rapid cooling, which enables microstructural refinement at the nanoscale to achieve high strength. However, high-strength nanostructured alloys produced by laser additive manufacturing often have limited ductility. In this work, we use L-PBF to print dual-phase nanolamellar high-entropy alloys (HEAs) of AlCoCrFeNi 2.1 that exhibit a combination of a high yield strength of about 1.3 gigapascals and a large uniform elongation of about 14 percent, which surpasses those of other state-of-the-art additively manufactured metal alloys. The high yield strength stems from the strong strengthening effects of the dual-phase structures that consist of alternating face-centred cubic and body-centred cubic nanolamellae; the body-centred cubic nanolamellae exhibit higher strengths and higher hardening rates than the face-centred cubic nanolamellae. The large tensile ductility arises owing to the high work-hardening capability of the as-printed hierarchical microstructures in the form of dual-phase nanolamellae embedded in microscale eutectic colonies, which have nearly random orientations to promote isotropic mechanical properties. The mechanistic insights into the deformation behaviour of additively manufactured HEAs have broad implications for the development of hierarchical, dual- and multi-phase, nanostructured alloys with exceptional mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

COWALKER:EFFECTIVE TRANSPORT PROPERTIES OF COMPOSITE MATERIALS

SF-23-026 This software computes effective transport properties of composite materials involving fibers and nanoparticles using a random-walk algorithm that efficiently scales to an arbitrary number of processes and cores. Effective transport properties (thermal, electrical) are key to bridge the microstructure of complex materials with its macroscopic behavior. Traditional approaches either use effective medium approximations (closed mathematical expressions that are approximation for certain conditions) or continuum simulation models such as finite element or finite volume, which require the generation of a mesh for each configuration explored. cowalker leverages the equivalence between laplacian or heat equation-based models and random walks to compute the asymptotic transport properties from an ensemble of first sojourn times of a random walker moving through the composite material. This allows us to directly define a composite material as a collection of particles and use algorithms developed for molecular dynamics to quickly compute the intersection of the walker with the different interfaces in the material. cowalker is developed in C++, and it relies on the GNU Scientific Library for random generation. cowalker is currently delivered as source code, so the GSL library is not included in cowalker's distribution. A more userfriendly version, cowalker.jl is currently in development and will be released as part of cowalker.

YANGUAS-GIL, ANGEL↗
DOE OSTI2026

Abnormal grain growth driven by high-temperature proton irradiation in nanocrystalline Ni

In this research we examine a nanocrystalline Ni thin film exposed to high-temperature proton irradiation and compare it with as-deposited and annealed-only counterparts. Despite lacking thermal spikes typical of heavy ions, 400 °C proton irradiation drives pronounced grain growth in select grains, whereas annealing alone yields only modest coarsening. Grain-boundary statistics show fewer low-angle boundaries (10–20°) and more high-angle boundaries (55–60°), consistent with irradiation-enhanced mobility of high-misorientation boundaries. The irradiated films retain a random texture, with no evidence of texture development or sharpening. Mechanisms, such as radiation-enhanced grain boundary diffusion, beam-induced heating, and ion channeling-mediated selective grain growth, are unlikely to be the predominant drivers to explain the resultant microstructure. Instead, we suggest irradiation-induced modifications of grain-boundary structure, including possible complexion transitions, as one plausible explanation for this selective grain growth and retention of random texture. However, additional temperature–dose studies are required to confirm the mechanism.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Fatigue behavior analysis and multi-scale modelling of chopped carbon fiber chip-reinforced composites under tension-tension loading condition

Here, the fatigue damage behavior of chopped carbon fiber chip-reinforced composite has been experimentally and numerically investigated. A large scatter is exhibited in the S-N diagram due to the random distribution of carbon fiber chips, and therefore a new analysis procedure is proposed to link the local microstructure to the fatigue behavior of the bulk material. Interrupted fatigue tests are also performed so that microstructure characterization can be conducted on the tested samples to analyze the crack initiation and propagation. Inspired from the experimental findings, a multi-scale progressive damage fatigue model is proposed to predict the fatigue behavior. The model incorporates a new stochastic chip-packing algorithm for microstructure reconstruction along with continuum damage models into the representative volume element (RVE) model in ABAQUS/Explicit. Finally, the simulation results based on the proposed model are in good agreement with the experimental data in terms of cracking modes and predicted life.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stochastic parametric skeletal dosimetry model for humans: General approach and application to active marrow exposure from bone-seeking beta-particle emitters

The objective of this study is to develop a skeleton model for assessing active marrow dose from bone-seeking beta-emitting radionuclides. This article explains the modeling methodology which accounts for individual variability of the macro- and microstructure of bone tissue. Bone sites with active hematopoiesis are assessed by dividing them into small segments described by simple geometric shapes. Spongiosa, which fills the segments, is modeled as an isotropic three-dimensional grid (framework) of rod-like trabeculae that “run through” the bone marrow. Randomized multiple framework deformations are simulated by changing the positions of the grid nodes and the thickness of the rods. Model grid parameters are selected in accordance with the parameters of spongiosa microstructures taken from the published papers. Stochastic modeling of radiation transport in heterogeneous media simulating the distribution of bone tissue and marrow in each of the segments is performed by Monte Carlo methods. Model output for the human femur at different ages is provided as an example. The uncertainty of dosimetric characteristics associated with individual variability of bone structure was evaluated. An advantage of this methodology for the calculation of doses absorbed in the marrow from bone-seeking radionuclides is that it does not require additional studies of autopsy material. The biokinetic model results will be used in the future to calculate individual doses to members of a cohort exposed to 89,90 Sr from liquid radioactive waste discharged to the Techa River by the Mayak Production Association in 1949–1956. Further study of these unique cohorts provides an opportunity to gain more in-depth knowledge about the effects of chronic radiation on the hematopoietic system. In addition, the proposed model can be used to assess the doses to active marrow under any other scenarios of 90 Sr and 89 Sr intake to humans.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2018

Role of refractory inclusions in the radiation-induced microstructure of APMT

Kanthal APMT is a promising FeCrAl-based alloy for accident-tolerant fuel cladding because of its excellent high-temperature oxidation resistance. In this study, powder metallurgy Kanthal APMT alloy, neutron irradiated to 1.8 dpa at nominally 382 °C, was characterized. On-zone STEM imaging revealed that radiation-induced dislocation loops with Burgers vectors of a/2 <111 > or and black dots tended to agglomerate in the vicinity of refractory inclusions. The densities and sizes of these loops decreased with distance from the inclusion-matrix interfaces. In addition, high-resolution energy-dispersive X-ray spectroscopy mapping was used to determine the inclusions to be either yttrium- or silicon-rich, as well as to detect the radial distribution of radiation-enhanced α' phase near these inclusions. A high density of randomly distributed Cr-rich α' phase was found, regardless of the presence of inclusions. Here, the results from this study provide insights into how microstructural features can locally tailor the radiation-induced defects in FeCrAl-based alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Role of crystallographic orientation on intragranular void growth in polycrystalline FCC materials

In this study, we study the effect of crystallographic orientation and applied triaxiality on the growth of intragranular voids. Two 3D full-field micromechanics methods are used, the dilatational visco-plastic fast-Fourier transform (DVP-FFT) and the crystal plasticity Finite Elements (CP-FE), both of which incorporate a combination of crystalline plasticity and dilatational plasticity. We demonstrate with several select cases that predictions of void growth from both formulations agree qualitatively. With the more computationally efficient DVP-FFT, additional effects of polycrystalline microstructure and the influence of nearest neighborhood are investigated. Crystals bearing a single intracrystalline void are studied in three types of 3D microstructural environments: isolated single crystals, individual equal-sized grains within a regular polycrystal, and individual variable sized grains within a polycrystal with grains and voids randomly located. We show that loading type plays a significant role. In strain-rate controlled conditions, voids in the hardest [111]-crystals grow the fastest in time, whereas in stress-controlled conditions, voids in the softest [100]-crystal grow the fastest in time. The analysis reveals that on average void growth is slower for the same starting orientation in the polycrystal than in the single crystal. We find that at the highest triaxiality tested that the correlation between crystal orientation and void growth rate in the polycrystal strengthens, drawing closer to that seen in the isolated single crystals. These results and model can help guide the microstructural design of polycrystalline materials with high strength and damage-tolerance in high-rate deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

High-Resolution Comonomer Sequencing of Blocky Brominated Syndiotactic Polystyrene Copolymers Using 13C NMR Spectroscopy and Computer Simulations

This work demonstrates the first high-resolution comonomer sequencing of Blocky brominated syndiotactic polystyrene (sPS-co-sPS-Br) copolymers based on pentad assign- ments of the quaternary carbon region of the nuclear magnetic resonance spectrum. Copolymers containing p-bromostyrene (Br-Sty) units were prepared in matched sets using postpolymerization bromination methods carried out in the heterogeneous gel state (Blocky) and homogeneous solution state (Random). Quantitative information from the quaternary carbon spectra, heteronuclear multiple bond correlation spectroscopy, electronic structure calculations, and simulated statistically random copolymers was correlated to confirm the carbon resonance assignments for all 20 possible pentad comonomer sequences. Using the experimental pentad sequence prevalences, a computer code was developed to simulate chains with microstructures typical of each sample as a means to visually represent the copolymer blockiness with quantitative precision. Based on the microstructure and distribution of run lengths in these chains, the simulations revealed that the Blocky copolymers contain a high degree of blockiness. By comparing the run lengths in the simulated chains to the average number of styrene units in a crystalline segment of sPS (found by small-angle X-ray scattering), copolymer crystallizability was predicted. For the simulated Blocky B-21% (21 mol % Br-Sty) chain, the probability of randomly selecting a styrene unit in a crystallizable block was 25.8%, while that in the simulated Random R-18% was zero, in excellent agreement with the experimental crystallization behavior measured by differential scanning calorimetry. Additionally, these predictions confirmed that the simulated chains accurately represent the ensemble of chains in their respective copolymer samples. Furthermore, each simulated Blocky chain contained one or more long sPS blocks that paralleled the measured 38-40 styrene units spanning a crystalline segment within the sPS/CCl4 gel. This finding affirmed that the long sPS segments originated from the precise lamellar structure within the heterogeneous gel morphology (i.e., block length is correlated with lamellar thickness). Overall, the ability to tailor the copolymer microstructure through control of the semicrystalline gel morphology opens the door to synthesizing ordered copolymers by postpolymerization functionalization processes with unprecedented levels of compositional control.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Anomalous lattice expansion of bcc Ta in helium-loaded diamond anvil cells

Anomalous lattice expansion of bcc Ta is observed in helium-loaded diamond anvil cell (DAC) experiments near 6 GPa and above 400 K, while co-loaded W, Mo, and Au exhibit normal thermal expansion. The Ta volume expansion increases with temperature, reaching ~14% near 650 K before plateauing, and is largely retained after recovery to ambient conditions. Time-resolved measurements at 500 K reveal progressive expansion over several hours, consistent with gradual, thermally activated He incorporation. The largely retained expansion during subsequent cooling and holding at 400 K indicates that the incorporated He is predominantly kinetically trapped. The data reveal two distinct regimes: below ~550 K, modest and spatially uniform expansion consistent with interstitial He trapping at isolated, randomly distributed vacancies; above ~550 K, He-vacancy cluster growth producing dramatically larger expansion, peak broadening, and a core–shell microstructure revealed by micron-resolution X-ray diffraction mapping. These results demonstrate that He is not always a passive pressure medium in DAC experiments and reveal a previously unrecognized regime of He-mediated lattice modification in Ta, complementing conventional ion-implantation studies relevant to nuclear and fusion structural materials.

Diamond anvil cell↗
DOE OSTI2021

A constitutive model incorporating grain refinement strengthening on metallic alloys

Surface nano-crystallization techniques have been recently developed as one of the most efficient ways to optimize materials’ structure, and therefore develop the local and global mechanical behavior as to increase strength without compromising ductility. Here, in this work, we present a constitutive model incorporating grain refinement hardening to simulate the nano-crystallization technique, specifically, surface mechanical attrition treatment. The computation is implemented using user-defined VUMAT subroutines. As an example of its application, a geometry model with full coverage of random impacts are employed. The results show that the model has rather precise predictability of grain size evolution during plastic deformation. The readily embedded with a computational code of material dynamics enables this novel model to be a promising tool to study the dynamic evolution of microstructures under plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2018

A detailed study of the microstructure and thermal stability of typical SiC fibers

Highlights: • The cross-sectional microstructure and thermal stability of typical SiC fibers were characterized via SEM and TEM. • The SiC fiber with gradient microstructure has better properties than that with uniform microstructure. • The graphite exhibits straight planes on the fiber surface while they're turbostratic inside the fiber. Continuous SiC fibers have attracted increasing research interest for their significant application in aerospace and nuclear energy. Control of inhomogeneity and decrement of defects are crucial for improving the mechanical and high-temperature performance of SiC fibers. Thus an understanding of fine and detailed microstructural and microchemical distribution of SiC fibers is urgently needed. In the present work, the cross-sectional phase distributions, morphologies and defects of amorphous, non-stoichiometric and near-stoichiometric SiC fibers were well characterized. From surface to core, the amorphous and non-stoichiometric fibers exhibited uniform microstructures, but a gradient change along the radial direction was observed in the near-stoichiometric fiber. Nanosized SiC and turbostratic carbon (2–4 nm) were randomly distributed inside the amorphous fiber. A large amount of graphite surrounding SiC grains appears in the non-stoichiometric fiber which possess low strength and weak thermal stability. The near-stoichiometric fiber has transgranular fracturing, high strength and favorable thermal stability, and the graphite planes are turbostratic inside the fiber but straight on the surface. The results of both energy-dispersive X-ray spectrometry measurements and first-principles calculations demonstrate that Al atoms can occupy Si sites in the SiC grains. Our findings offer fine understanding for fabricating SiC fibers with superior properties.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Simulation of dynamic crystal plasticity with a Lagrangian discontinuous Galerkin hydrodynamic method

Here we present a new Lagrangian modal discontinuous Galerkin (DG) hydrodynamic method that supports a dynamic dislocation based crystal plasticity model for simulating the mechanical behavior of crystallographic materials, both single crystal and polycrystalline, under dynamic conditions. A modal DG approach is used to evolve fields relevant to conservation laws. These fields are approximated by Taylor series polynomials of varying degree. These polynomials describe macro-scale hydrodynamic behavior while their evolution is determined by evaluating the dynamic crystal plasticity model at material points within the element. The dynamic crystal plasticity model is sensitive to the time increment size, with too large of time increments leading to instability in the model. To mitigate this, the temporal evolution of the dynamic crystal plasticity model is achieved with the combination of a sub-incrementing scheme with Heun’s third-order time integration scheme, which is also used to temporally evolve the governing equations. The implementation of the dynamic crystal plasticity model within the DG framework is tested using a 2D approximation of the Taylor impact test with a single crystal material, using quadratic elements that have faces that can bend. In addition to the standard continuous material modeling, we propose a new simulation method that would represent the heterogeneous behavior of polycrystalline microstructures within an element by varying the position and material properties of the material points within the element. This method is demonstrated using random orientation distributions on materials points that are arranged in both structured and random configurations.

42 ENGINEERING↗
DOE OSTI2019

Development of Texture in Ultrafine-Grained Low-Carbon Steel Processed through Equal-Channel Angular Pressing

Developments of microstructures and texture are investigated for a low-carbon steel deformed by equal-channel angular pressing (ECAP) at room temperature for equivalent strain (ε{sub vm}) of 16.8. ECAP at ε{sub vm} = 0.6 reduces grain size by two orders of magnitude. With increasing strain, grain size reduces further and high-angle grain boundary (HAGB) fraction improves by grain subdivision and its change in orientation. ECAP of low-carbon steel up to ε{sub vm} = 16.8 can produce ultrafine grains of 0.2 µm size with HAGB fraction of 82%. The as-received steel has low texture index. Microstructural changes strongly influence texture development. It increases with equivalent strain as grain subdivision continues. Texture index fluctuates at intermediate strain range due to randomization of initial texture. Texture index reaches saturation at the high equivalent strain. On ECAP at low to intermediate strain ε{sub vm} = 0.6-6, components of both α (F{sub θ}, J{sub θ}, and J-bar {sub θ}) and γ (D{sub 1θ}, D{sub 2θ}, and E{sub θ}) fibers are developed though all of them deviate from their ideal positions. At higher strain (ε{sub vm} = 9-16.8), the γ fiber components (D{sub 1θ}, D{sub 2θ}, E{sub θ}) are strengthened, and the E{sub θ} component reaches the highest intensity of ≈ 17 at ε{sub vm} = 12. There is no texture symmetry at low to high strain level. The presence of pearlite in low-carbon steel enhances strongly the deviation of texture components from their ideal positions in Euler’s space as well as it increases the intensities of the components more than that of IF steel for a similar equivalent strain.

36 MATERIALS SCIENCE↗