SEARCH · Search NASA

Results for “ray trace”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2024

Qualitative Conditions for Reasonable Estimates of Kerma Using Total and Kerma Cross Section Attenuation of Photons

Performing a full adjoint simulation in the Integrated Tiger Series (ITS) can be time consuming to obtain statistically significant results. The ray-trace capability in ITS allows for rapid scoping calculations of the uncollided kerma from photon sources without needing to run a full adjoint simulation. However, the uncollided estimate will always underestimate the full-physics kerma since it neglects scattered radiation, and under certain conditions, the result from the capability may not provide a sufficiently accurate estimate of the full-physics kerma. To exemplify the conditions in which the capability provides reasonable estimates, two problem geometries with different materials are simulated using the full adjoint capability as well as the ray-trace capability with a total cross section treatment and a new kerma-attenuation cross-section treatment. The results are then compared to show under which conditions the estimates are accurate. Reasonable estimates are provided from the ray-trace feature when there is minimal scattering into a region of interest occurring, such as with low-Z material and when the photons travel through small amounts of material.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Electron cyclotron emission measurements and modeling in optically semi-transparent plasma on the HSX stellarator

On the Helically Symmetric Experiment (HSX), electron cyclotron emission (ECE) at the second harmonic of the electron gyrofrequency is measured with a 16-channel heterodyne receiver. An ECE radiometer diagnostic has been calibrated with a broadband frequency source, allowing independent measurements of the electron temperature. The antenna pattern has a significant impact on the measurements, and modeling its effect is necessary to produce an ECE radiation temperature spectrum. Measurements, calibration results, and modeling of the ECE data are presented in this paper. At a relatively high plasma density, HSX plasmas are thermal, and the radiation temperature measured by the radiometer is in good agreement with the electron temperature measured by a Thomson scattering diagnostic. At a relatively low plasma density, the deviation from a Maxwellian distribution is large, and asymmetry in the radiation temperature profile is measured. These measurements are supported by single-pass and multi-pass ray tracing calculations of the electron cyclotron emission using the TRAVIS ray tracing code. Thermal and nonthermal electron populations exist in HSX, and the effect of these populations on the asymmetry in the measured emission is presented.

Cyclotron radiation↗

DOE OSTI2024

Prediction of regional infrasound produced by supersonic sources using a ray-based Mach cone source

The geometry of the Mach cone produced by a supersonic source is analyzed and mapped into initial conditions used in acoustic ray tracing. The resulting source model is combined with spherical geometry ray tracing methods to enable propagation simulations for infrasonic signals produced by bolides, space debris, rockets, aircraft, and other fast-than-sound sources out to typical infrasonic observation distances of hundreds or thousands of kilometers. Idealized linear and parabolic trajectories typical of bolides and rockets, respectively, are used to demonstrate the calculation of regional infrasonic signals produced by such sources and characteristics of the radiated infrasonic waves are found to vary strongly with the geometry of the trajectory and atmospheric structure. Predicted regional infrasonic signals are compared with those observed from a November 2020 bolide that passed over Scandinavia using a combination of institutionally maintained infrasound stations and “citizen scientist” data from the Raspberry Shake data repository.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

Prediction of regional infrasound produced by supersonic sources using a ray-based Mach cone source

42 ENGINEERING↗

DOE OSTI2021

Laser heating system at the Extreme Conditions Beamline, P02.2, $\mathrm{PETRA III}$

A laser heating system for samples confined in diamond anvil cells paired with in situ X-ray diffraction measurements at the Extreme Conditions Beamline of PETRA III is presented. The system features two independent laser configurations (on-axis and off-axis of the X-ray path) allowing for a broad range of experiments using different designs of diamond anvil cells. The power of the continuous laser source can be modulated for use in various pulsed laser heating or flash heating applications. An example of such an application is illustrated here on the melting curve of iron at megabar pressures. The optical path of the spectroradiometry measurements is simulated with ray-tracing methods in order to assess the level of present aberrations in the system and the results are compared with other systems, that are using simpler lens optics. Based on the ray-tracing the choice of the first achromatic lens and other aspects for accurate temperature measurements are evaluated.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Bent Laue crystal anatomy: new insights into focusing and energy-dispersion properties

X-ray Laue-type monochromators are common and essential optical components at many high-power X-ray facilities, e.g. synchrotron facilities. The X-ray optics of bent Laue crystals is a well developed area. An incident X-ray beam penetrating a bent Laue crystal will result in a diffracted beam with different angles and energies. There is a need for a way of organizing the rays that allows one to sort out the energy and spatial properties of the diffracted beam. The present work introduces a new approach for describing the general behaviour of bent Laue crystals from a ray-tracing point of view. This quasi-monochromatic beam approach provides an intuitive view of bent-crystal diffraction and leads to deeper understanding. It explains the energy and spatial properties of common and special cases of bent Laue optics, predicts phenomena that can improve energy-dispersion-related X-ray imaging techniques and provides a theoretical framework that makes ray-tracing simulation easier to realize.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Dislocation contrast on X-ray topographs under weak diffraction conditions

The contrast of dislocations in 4H-SiC crystals shows distinctive features on grazing-incidence X-ray topographs for diffraction at different positions on the operative rocking curve. Ray-tracing simulations have previously been successfully applied to describe the dislocation contrast at the peak of a rocking curve.The present work shows that the dislocation images observed under weak diffraction conditions can also be simulated using the ray-tracing method. Furthermore, these simulations indicate that the contrast of the dislocations is dominated by orientation contrast. Analysis of the effective misorientation reveals that the dislocation contrast in weak-beam topography is more sensitive to the local lattice distortion, consequently enabling information to be obtained on the dislocation sense which cannot be obtained from the peak.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Development and Experimental Optimization of High-Temperature Modeling Tools and Methods for Concentrated Solar Power Particle - Systems

A novel, open-source radiative modeling toolset was developed to extend the functionality of particle-based modeling software (e.g. discrete element method (DEM)) to environmental conditions relevant to concentrated solar power applications. This toolset was optimized for deployment on desktop workstations instead of high-performance computing systems, to render such tools more accessible to the research community. Both particle-based modeling and radiative exchange modeling are computationally expensive and often require specialized programming expertise, making these methods cumbersome to use. Recent developments in DEM software by DCS Computing have greatly reduced these challenges, providing a graphical-user-interface based platform and modeling optimization for desktop workstations, HPCs, and cloud computing. The University of Dayton leveraged the experience of DCS Computing in developing a user-friendly, open-source radiative heat transfer expansion for DEM modeling. The University of Dayton DEM+ radiative modeling toolset was developed using a combination of fundamental experimental measurements, modeling, and simplified flow experiments over a range of temperatures and flow conditions. The toolset provides researchers with access to multiple radiative models including an accelerated Monte-Carlo Ray Tracing (application agnostic, highly computationally expensive), an expanded database of distance-based approximations (application limited, computationally light), and a weighted blending of the two methods capable of achieving over 90% reduction in computation time with equivalent accuracy compared to Monte-Carlo Ray Tracing. Through a graphical user interface, users can customize the radiative models to match their desired accuracy and available computational resources, improving access to particle based modeling for the research community. Ceramic sintered bauxite proppants were used in modeling and experimentally as a baseline. Both the radiative heat transfer and flow properties for particulate systems were investigated at elevated temperatures up to 800 °C. The major accomplishments for this work include a verified, open-source radiative modeling toolset to be distributed amongst the research community and the fabrication of three small-scale test facilities to investigate particle behavior and tune DEM flow properties for operation up to 800 °C. The findings have been shared with the research community via conference modeling workshops, deployment of the tools in DCS Computing Aspherix®, and open-source access to the developed radiative modeling tool. The development of next-generation CSP facilities and thermal energy storage systems based on ceramic particles requires providing access to computationally efficient and accurate modeling tools. Particles will experience a wide range of environments (20-800 °C) and handling conditions (dilute curtains or dense packing), requiring specially designed and optimized equipment. Optimizing solid particle physics models and establishing best-practices for particle modeling in CSP environments will assist researchers with designing optimized equipment, accelerating the deployment of more economically-competitive CSP facilities.

14 SOLAR ENERGY↗

DOE OSTI2025

Fast physics-based launcher optimization for electron cyclotron current drive

With the increased urgency to design fusion pilot plants, fast optimization of electron cyclotron current drive (ECCD) launchers is paramount. Traditionally, this is done by coarsely sampling the 4D parameter space of possible launch conditions consisting of (1) the launch location (constrained to lie along the reactor vessel), (2) the launch frequency, (3) the toroidal launch angle, and (4) the poloidal launch angle. For each initial condition, a ray-tracing simulation is performed to evaluate the ECCD efficiency. Unfortunately, this approach often requires a large number of simulations (sometimes millions in extreme cases) to build up a dataset that adequately covers the plasma volume, which must then be repeated every time the design point changes. Here we adopt a different approach. Rather than launching rays from the plasma periphery and hoping for the best, we instead directly reconstruct the optimal ray for driving current at a given flux surface using a reduced physics model coupled with a commercial ray-tracing code. Repeating this throughout the plasma volume requires only hundreds of simulations, constituting a significant speedup. The new method is validated on two separate example tokamak profiles, and is shown to reliably drive localized current at the specified flux surface with the same optimal efficiency as obtained from the traditional approach.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Analyzing acoustic emission data to identify cracking modes in cement paste using an artificial neural network

This research is focused on the identification of cracking mechanisms for cement paste using acoustic emission data, recorded from compression and notched four-point bending tests. A procedure is developed for analyzing the data by employing an agglomerative hierarchical clustering method, an artificial neural network, and a ray-tracing source location algorithm. An agglomerative hierarchical clustering method is utilized to cluster the AE data from a compression test using frequency-dependent features. A neural network is trained using the compression test data and applied to the AE data emitted during the four-point bending test. The clustered data from the four-point bending test is localized using a ray-tracing algorithm. Based on the occurrence and locations of the clustered events and signal feature analyses, potential cracking mechanisms are identified and assigned.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Absolute throughput calibration of multiple spherical crystals for the Orion High-REsolution X-ray spectrometer (OHREX)

We present absolute throughput analysis of several crystals for the Orion High-REsolution X-ray (OHREX) imaging crystal spectrometer using ray tracing and experimental measurements. The OHREX spectrometer is a high-resolution x-ray spectrometer designed to measure spectral line shapes at the Orion laser facility. The spectrometer is fielded with up to two spherical crystals simultaneously covering two independent spectral ranges. Each crystal has a nominal radius of curvature of R = 67.2 cm and is fielded at a nominal Bragg angle of 51.3°. To cover different bands of interest, several different crystals are available, including Ge (111), KAP, and several cuts of quartz, whose resolving power λ/Δλ exceeds 10 000. The calibrated response of the available crystals has previously been reported from measurements at the EBIT-I electron beam ion trap at Lawrence Livermore National Laboratory. Here, we model the absolute throughput of each crystal using ray tracing and verify the results using experimental data for the quartz $(10\bar{1}1)$ crystal.

47 OTHER INSTRUMENTATION↗

DOE OSTI2024

Investigating the origin of the far-field reflection interference fringe (RIF) of microdroplets

We show that the reflection interference fringe (RIF) is formed on a screen far away from the microdroplets placed on a prism-based substrate, which have low contact angles and thin droplet heights, caused by the dual convex–concave profile of the droplet, not a pure convex profile. The geometric formulation shows that the interference fringes are caused by the optical path difference when the reflected rays from the upper convex profile at the droplet–air interface interfere with reflection from the lower concave profile at oblique angles lower than the critical angle. Analytic solutions are obtained for the droplet height and the contact angle out of the fringe number and the fringe radius in RIF from the geometric formulation. Furthermore, the ray tracing simulation is conducted using the custom-designed code. The geometric formulation and the ray tracing show excellent agreement with the experimental observation in the relation between the droplet height and the fringe number and the relation between the contact angle and the fringe radius. This study is remarkable as the droplet's dual profile cannot be easily observed with the existing techniques. However, the RIF technique can effectively verify the existence of a dual profile of the microdroplets in a simple setup. In this work, the RIF technique is successfully developed as a new optical diagnostic technique to determine the microdroplet features, such as the dual profile, the height, the contact angle, the inflection point, and the precursor film thickness, by simply measuring the RIF patterns on the far-field screen.

42 ENGINEERING↗

DOE OSTI2026

Elevating SolTrace's Capabilities for the Next Generation of Concentrating Solar Analysis

SolTrace is an open-source Monte Carlo ray tracing software developed at NREL. SolTrace can characterize concentrating solar thermal (CST) collector optical performance and is CST technology agnostic. Shown in Fig. 1, SolTrace is a foundational tool in NREL's CST system and component modeling suite. SolTrace's generic surface elements can flexibly model novel collector and receiver designs to predict spatial and temporal flux distributions - critical to understand for CST component design, performance prediction, and system integration. Since its initial development, SolTrace has over 1,650 references on Google Scholar, over 9,800 downloads since 2017, and has served the CST research and development community as a benchmark of 3rd party verification. SolTrace provides users with many options for defining surface shape and boundaries. However, SolTrace provides limited documentation which can result in a steep learning curve for new users. Additionally, SolTrace lacks the computational performance required to evaluate optical performance of a CST system over the course of a year and/or iteratively over design parameters in a timely manner. To address this, we are working towards a new release of SolTrace that enables increased computational throughput by implementing ray tracing acceleration structures and enabling GPU parallelization. Additionally, we are working to improve SolTrace's usability, accessibility, and maintainability by (1) automating solar position time-dependent simulation processes, (2) creating general CST collector templates of grouped elements, (3) updating the user interface to better visualize model inputs and outputs, and (4) creating a user support network through forums, "how to" videos, and documentation.

14 SOLAR ENERGY↗

DOE OSTI2021

The Simons Observatory: modeling optical systematics in the Large Aperture Telescope

We present geometrical and physical optics simulation results for the Simons Observatory Large Aperture Telescope. This work was developed as part of the general design process for the telescope, allowing us to evaluate the impact of various design choices on performance metrics and potential systematic effects. The primary goal of the simulations was to evaluate the final design of the reflectors and the cold optics that are now being built. We describe nonsequential ray tracing used to inform the design of the cold optics, including absorbers internal to each optics tube. We discuss ray tracing simulations of the telescope structure that allow us to determine geometries that minimize detector loading and mitigate spurious near-field effects that have not been resolved by the internal baffling. We also describe physical optics simulations, performed over a range of frequencies and field locations, that produce estimates of monochromatic far-field beam patterns, which in turn are used to gauge general optical performance. Finally, we describe simulations that shed light on beam sidelobes from panel gap diffraction.

Gudmundsson, Jon E. (ORCID:0000000317600355)↗

DOE OSTI2020

The Simons Observatory: Modeling Optical Systematics in the Large Aperture Telescope

We present geometrical and physical optics simulation results for the Simons Observatory Large Aperture Telescope. This work was developed as part of the general design process for the telescope; allowing us to evaluate the impact of various design choices on performance metrics and potential systematic effects. The primary goal of the simulations was to evaluate the final design of the reflectors and the cold optics which are now being built. We describe non-sequential ray tracing used to inform the design of the cold optics, including absorbers internal to each optics tube. We discuss ray tracing simulations of the telescope structure that allow us to determine geometries that minimize detector loading and mitigate spurious near-field effects that have not been resolved by the internal baffling. We also describe physical optics simulations, performed over a range of frequencies and field locations, that produce estimates of monochromatic far field beam patterns which in turn are used to gauge general optical performance. Finally, we describe simulations that shed light on beam sidelobes from panel gap diffraction.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2025

Scaling Uintah on the Aurora Exascale System up to 122,880 Intel Ponte Vecchio Xe Stacks

The challenge of being able to scale application codes based on the Asynchronous Many-Task (AMT) Uintah framework on the Department of Energy (DOE) Aurora exascale system is addressed in this work by considering a challenging Reverse Monte Carlo Ray Tracing radiation benchmark calculation. This benchmark involves potentially global all-to-all communication and uses adaptive mesh refinement and ray tracing to achieve scalability. This benchmark has been used as part of previous scalability studies on a number of pre-exascale systems and on the DOE Frontier exascale system. This paper describes steps taken to enable this benchmark to run successfully on up to 10,240 nodes and 122,880 Intel® Ponte Vecchio Xe stacks on the DOE Aurora exascale system. This scalability was achieved through a limited number of experiments on Aurora, given machine loads and its uniqueness. These experiments constitute valuable lessons learned to achieve scalability at this level. The resulting scalability runs, while few in number, demonstrate relatively good strong-scaling characteristics. A detailed analysis of these results provides important indications about the path to scalability on Aurora for future work. Overall, these results continue the remarkable ability of this AMT approach to produce scalable solutions for challenging problems at extreme scale on heterogeneous architectures.

Garcia, Marta [Argonne National Laboratory (ANL)]↗

DOE OSTI2022

Spectral broadening from turbulence in multiscale lower hybrid current drive simulations

Abstract The scattering of lower hybrid (LH) waves due to scrape-off layer filaments is investigated. It is revealed that scattering can account for the LH spectral gap without any ad hoc modification to the wave-spectrum. This is shown using a multiscale simulation approach which allows, for the first time, the inclusion of full-wave scattering physics in ray-tracing/Fokker–Planck calculations. In this approach, full-wave scattering probabilities are calculated for a wave interacting with a statistical ensemble of filaments. These probabilities are coupled to ray-tracing equations using radiative transfer theory. This allows the modeling of scattering along the entire ray-trajectory, which can be important in the multi-pass regime. Simulations are conducted for LH current drive (LHCD) in Alcator C-Mod, resulting in excellent agreement with experimental current and hard x-ray profiles. A region in filament parameter space is identified in which the impact of scattering on LHCD is saturated. Such a state coincides with experimental LHCD measurements, suggesting saturation indeed occurs in C-Mod, and therefore the exact statistical properties of the filaments are not important.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2025

Data for NB6 HBRR Science Design ORNL/TM-2025/3807

Data for the report (ORNL/TM-2025/3807) that describes the calculations and the Monte Carlo Ray Tracing simulations performed using the McStas package to determine the coatings and geometry for the NB-6 guide. It provides the information to inform the mechanical design, validation tests and verification that it meets the science requirements.

47 OTHER INSTRUMENTATION↗