Search NASA⌕ Search

SEARCH · Search NASA

Results for “reference cells”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Broadband light absorption enhancement in polymer photovoltaics using metal nanowall gratings as transparent electrodes

The authors investigate light absorption in organic solar cells in which indium tin oxide (ITO) is replaced by a new metallic architecture (grating) as a transparent electrode. Different from typical metal nanowire gratings, our gratings consist of metal nanowalls with nanoscale footprint and (sub)microscale height [Adv. Mater. 23, 2469 (2011)], thus ensuring high optical transmittance and electrical conductivity. Simulations reveal that a broadband and polarization-insensitive light absorption enhancement is achieved via two mechanisms, when such silver nanowall gratings are employed in P3HT:PCBM based solar cells. Overall absorption enhanced by ~23% compared to a reference cell with ITO electrode.

14 SOLAR ENERGY↗

Modeling the potential of screen printed front junction CZ silicon solar cell with tunnel oxide passivated back contact

Carrier selective passivated contacts composed of thin oxide, n + polycrystalline Si and metal on top of a n-Si absorber can significantly lower the recombination current density (J orear ≤8 fA/cm 2 ) under the contact while providing excellent specific contact resistance (5–10 mΩ-cm 2 ); 25.1% efficient small area cells with photolithography front contacts on boron doped selective emitter and Fz wafers have been achieved by Fraunhofer ISE using their tunnel oxide passivated contact (TOPCon) approach. This paper shows a methodology to model such passivated contact cells using Sentaurus device model, which involves replacing the TOPCon region by carrier selective electron and hole recombination velocities to match the measured J orear of the TOPCon region as well as all the light IV values of the cell. We first validated the methodology by modeling a 24.9% reference cell. The model was then extended to assess the efficiency potential of large area TOPCon cells on commercial grade n-type Cz material with screen-printed front contacts. To use realistic input parameters, a 21% n-type PERT cell was fabricated on Cz wafer (5 Ω-cm, 1.5-ms lifetime). Modeling showed that the cell efficiency will improve to only 21.6% if the back of this cell is replaced by the above TOPCon, and the performance is limited by the homogenous emitter. Efficiency was then modeled to improve to 22.6% with the implementation of selective emitter (150/20 Ω/sq). Lastly, it is shown that screen printing of 40-µm-wide lines and improved bulk material (10 Ω-cm, 3-ms lifetime) can raise the single side TOPCon Cz cell efficiency to 23.2%.

14 SOLAR ENERGY↗

Temperature and illumination dependence of silicon heterojunction solar cells with a wide range of wafer resistivities

Abstract Recently, the significant improvements in the surface and contact passivation of silicon (Si) solar cells as well as their bulk quality have shifted their operating point to higher injections. Hence, they are less dependent on wafer doping. This shift opens an opportunity of using high‐resistivity wafers for practical photovoltaic applications, introducing a promising approach to push the cell efficiency towards the intrinsic limit and to improve the module reliability by increasing the cell breakdown voltage. Therefore, insights into the performance of Si solar cells using high‐resistivity wafers at various operating temperatures are of significant interest. In this study, we investigate the temperature‐ and illumination‐dependent performance of Si heterojunction (SHJ) solar cells using a wide range of wafer resistivities (between 3 and 1000 Ω⋅cm). Although a reduction in the passivation quality of the passivating contacts is observed at elevated temperature, the impact on the temperature coefficient of the open‐circuit voltage (TC V oc )—the dominant contributor to the temperature coefficient (TC) of the cell efficiency—is very limited. Their TC V oc are still dominated by the temperature dependence of the effective intrinsic carrier concentration. Furthermore, we also find that the investigated cells are more sensitive to temperature variation at lower illumination intensities. It is noteworthy that the efficiency of the cells fabricated using high‐resistivity wafers is comparable to that of the reference cells at any given temperature, highlighting the potential of using high‐resistivity wafers for solar cells.

14 SOLAR ENERGY↗

Optimization towards high density quantum dots for intermediate band solar cells grown by molecular beam epitaxy

We report high density quantum dots (QDs) formation with optimized growth temperature and V/III ratio. At lower growth temperature, QD density is increased, due to smaller surface migration length of In adatoms. With higher V/III, the QD density is higher but it results in large clusters formation and decreases the QD uniformity. The QD solar cell was fabricated and examined. An extended spectral response in contrast to the GaAs reference cell was presented but the external quantum efficiency at energies higher than GaAs band gap is reduced, resulting from the degradation for the emitter above the strained QD layers.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

See-through amorphous silicon solar cells with selectively transparent and conducting photonic crystal back reflectors for building integrated photovoltaics

Thin semi-transparent hydrogenated amorphous silicon (a-Si:H) solar cells with selectively transparent and conducting photonic crystal (STCPC) back-reflectors are demonstrated. Short circuit current density of a 135 nm thick a-Si:H cell with a given STCPC back-reflector is enhanced by as much as 23% in comparison to a reference cell with an ITO film functioning as its rear contact. Concurrently, solar irradiance of 295 W/m{sup 2} and illuminance of 3480 lux are transmitted through the cell with a given STCPC back reflector under AM1.5 Global tilt illumination, indicating its utility as a source of space heating and lighting, respectively, in building integrated photovoltaic applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Cyclododecane as support material for clean and facile transfer of large-area few-layer graphene

The transfer of chemical vapor deposited graphene is a crucial process, which can affect the quality of the transferred films and compromise their application in devices. Finding a robust and intrinsically clean material capable of easing the transfer of graphene without interfering with its properties remains a challenge. We here propose the use of an organic compound, cyclododecane, as a transfer material. This material can be easily spin coated on graphene and assist the transfer, leaving no residues and requiring no further removal processes. The effectiveness of this transfer method for few-layer graphene on a large area was evaluated and confirmed by microscopy, Raman spectroscopy, x-ray photoemission spectroscopy, and four-point probe measurements. Schottky-barrier solar cells with few-layer graphene were fabricated on silicon wafers by using the cyclododecane transfer method and outperformed reference cells made by standard methods.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A novel cell weighing method based on the minimum immobilization pressure for biological applications

A novel weighing method for cells with spherical and other regular shapes is proposed in this paper. In this method, the relationship between the cell mass and the minimum aspiration pressure to immobilize the cell (referred to as minimum immobilization pressure) is derived for the first time according to static theory. Based on this relationship, a robotic cell weighing process is established using a traditional micro-injection system. Experimental results on porcine oocytes demonstrate that the proposed method is able to weigh cells at an average speed of 16.3 s/cell and with a success rate of more than 90%. The derived cell mass and density are in accordance with those reported in other published results. The experimental results also demonstrated that this method is able to detect less than 1% variation of the porcine oocyte mass quantitatively. It can be conducted by a pair of traditional micropipettes and a commercial pneumatic micro-injection system, and is expected to perform robotic operation on batch cells. At present, the minimum resolution of the proposed method for measuring the cell mass can be 1.25 × 10{sup −15 }kg. Above advantages make it very appropriate for quantifying the amount of the materials injected into or moved out of the cells in the biological applications, such as nuclear enucleations and embryo microinjections.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Measurements of Six-Junction Concentrator Solar Cells

Accurate measurements of six-junction inverted metamorphic concentrator solar cells under AM1.5 direct spectrum are obtained by adjusting the spectrum of a tunable high-intensity solar simulator with custom mirrors. Isotype reference cells and broadband InGaAs QE calibration cells were developed for accurate measurements. Modeling and varying the illumination show that an unavoidable 15% - 17% overillumination on the sixth junction does not result in significant error of these 6J IMM devices. Spectrally adjusted flash measurements are independently confirmed by NREL's Cell and Module Performance team. Concentration measurements of a 6J IMM solar cell resulted in 47.1 ± 3.2% (absolute) efficiency at 143 suns.

41 EE - Solar Energy Technologies Office (EE-4S)↗

Holographic modification of TiO{sub 2} nanostructure for enhanced charge transport in dye-sensitized solar cell

We show that the photocurrent and energy conversion efficiency of dye-sensitized solar cells can be greatly enhanced with holographic modification to the morphology of TiO{sub 2} electrode. The nanoporous electrode coated onto conducting glass was irradiated by three interfering laser beams at 1064 nm incident from the backside of the substrate. This generated two-dimensional periodic pillars of higher density in the electrode, through which the photoexcited electrons could be extracted more effectively. The cells fabricated with modified electrodes exhibited average photocurrent and efficiency of 17.14 mA/cm{sup 2} and 9.03%, while 14.91 mA/cm{sup 2} and 7.83% were obtained from the reference cells. It was attributed to the enhanced charge transport accompanied by the reduction of internal resistance of the electrode.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Graded band gap GaInNAs solar cells

Dilute nitride GaInN(Sb)As with a band gap (E{sub g}) of 1.0 eV is a promising material for the integration in next generation multijunction solar cells. We have investigated the effect of a compositionally graded GaInNAs absorber layer on the spectral response of a GaInNAs sub cell. We produced band gap gradings (ΔE{sub g}) of up to 39 meV across a 1 μm thick GaInNAs layer. Thereby, the external quantum efficiency—compared to reference cells—was increased due to the improved extraction of photo-generated carriers from 34.0% to 36.7% for the wavelength range from 900 nm to 1150 nm. However, this device figure improvement is accompanied by a small decrease in the open circuit voltage of about 20 mV and the shift of the absorption edge to shorter wavelengths.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Indoor Soil Deposition Chamber: Evaluating Effectiveness of Antisoiling Coatings

An indoor soil deposition method has been developed to simulate natural soil deposition on glass coupons or one-cell and multicell photovoltaic (PV) modules. This method uses variable ambient humidity, coupon/module temperature, and dust composition within a single custom-made chamber to create a natural and uniform soil deposition layer. Antisoiling (AS) coatings from two different manufacturers were applied on two one-cell monocrystalline silicon modules. Three layers of Arizona road dust have been deposited on the one-cell modules with AS coatings and an uncoated one-cell reference module at varied humidity levels. The soiled modules were exposed to an open-circuit subsonic wind tunnel at varying speeds and the effectiveness of AS coatings have been quantified using the transmittance gain. Transmittance loss resulting from the AS coating has been measured and compared with the transmittance of the uncoated reference module using a reflectance spectrophotometer. Reflectance measurements have also been taken to compare the transmittance loss of Arizona road dust and soil collected from PV modules' superstrates. The soiled one-cell modules were then exposed to rain from a rain simulator. The transmittance gain due to rain exposure is quantified using a rain gain and rain coefficient. These tests cumulatively may be used to help develop a test standard for evaluating the effectiveness of AS coatings.

14 SOLAR ENERGY↗

Application of copper thiocyanate for high open‐circuit voltages of CdTe solar cells

Abstract Copper thiocyanate (CuSCN) has proven to be a low‐cost, efficient hole‐transporting material for the emerging organic–inorganic perovskite solar cells. Herein, we report that CuSCN can also be applied to CdTe thin‐film solar cells to achieve high open‐circuit voltages ( V OC s). By optimizing the thickness of the thermally evaporated CuSCN films, CdTe cells fabricated by close space sublimation in the superstrate configuration have achieved V OC s as high as 872 mV, which is about 20–25 mV higher than the highest V OC for the reference cells using the standard Cu/Au back contacts. CuSCN is a wide bandgap p ‐type conductor with a conduction band higher than that of CdTe, leading to a conduction band offset that reflects electrons in CdTe, partially explaining the improved V OC s. However, due to the low conductivity of CuSCN, CdTe cells using CuSCN/Au back contacts exhibited slightly lower fill factors than the cells using Cu/Au back contacts. With optimized CdS:O window layers, the power conversion efficiency of the best CdTe cell, using CuSCN/Au back contact, is 14.7%: slightly lower than that of the best cell (15.2%) using Cu/Au back contact. Copyright © 2015 John Wiley & Sons, Ltd.

Paudel, Naba R.↗

Electron-Selective TiO 2 Contact for Cu(In,Ga)Se 2 Solar Cells

The non-toxic and wide bandgap material TiO 2 is explored as an n-type buffer layer on p-type Cu(In,Ga)Se 2 (CIGS) absorber layer for thin film solar cells. The amorphous TiO 2 thin film deposited by atomic layer deposition process at low temperatures shows conformal coverage on the CIGS absorber layer. Solar cells from non-vacuum deposited CIGS absorbers with TiO 2 buffer layer result in a high short-circuit current density of 38.9 mA/cm 2 as compared to 36.9 mA/cm 2 measured in the reference cell with CdS buffer layer, without compromising open-circuit voltage. The significant photocurrent gain, mainly in the UV part of the spectrum, can be attributed to the low parasitic absorption loss in the ultrathin TiO 2 layer (~10 nm) with a larger bandgap of 3.4 eV compared to 2.4 eV of the traditionally used CdS. Overall the solar cell conversion efficiency was improved from 9.5% to 9.9% by substituting the CdS by TiO 2 on an active cell area of 10.5 mm2. In conclusion, optimized TiO 2 /CIGS solar cells show excellent long-term stability. The results imply that TiO 2 is a promising buffer layer material for CIGS solar cells, avoiding the toxic CdS buffer layer with added performance advantage.

14 SOLAR ENERGY↗

Investigating the effect of screen-printed structured graphite electrodes with low tortuosity for high-capacity and fast-charging lithium-ion batteries

A flexible screen-printed graphite electrode was fabricated as an anode for developing fast-charging lithium-ion batteries with low tortuosity. A homogenous anode ink was prepared by mixing graphite as the active material, carbon black (C45) as the conductive additive, and polyvinylidene fluoride (PVDF) as the binder in N-Methyl-2-pyrrolidone (NMP) solvent. The ink was deposited on a flexible copper foil via a stainless-steel screen consisting of an array of pores, that act as secondary pore networks (SPNs), using the screen-printing process. Lithium-ion battery half-cells were assembled using the printed graphite anode, lithium metal foil as the counter electrode, and 1.2 M lithium hexafluorophosphate (LiPF 6 ) in ethyl carbonate: ethyl methyl carbonate (EC: EMC = 3:7) as the electrolyte. The effect of SPNs on the cell performance was investigated by performing formation, rate and cycling tests on the assembled cells, at different C-rates. It was observed that the cells consisting of SPNs with a pore size of 100 μm and edge-to-edge distance of 100 μm between the pores exhibited significantly higher specific capacities of 168 and 129 mAh/g when compared to reference cells without SPNs, which had capacities of 120 and 85 mAh/g, at high C-rates of 4 C and 6 C, respectively. The cells with SPNs also demonstrated excellent cycling performance with ~ 95% capacity retention after 100 cycles at 2 C.

Fast charging lithium-ion battery↗

The Baseline Performance Reference for Irradiance in PV System Applications

This report proposes the definition of a new baseline performance reference (BPR). The definition goes beyond existing standards pertaining to photovoltaic (PV) reference cells and devices to define the response under all possible operating conditions in the field. Field evaluations using BPR devices will be more sensitive to performance anomalies than pyranometers because they track PV system power output more closely. At the same time, they will be able to detect a broader range of performance anomalies than traditional matched reference devices, which might have matching defects. The BPR definition also opens the door to new practices in resource assessment and yield prediction. Solar resource data can be collected or modeled and validated directly as BPR irradiance, and PV system simulations based on BPR irradiance need fewer assumptions and less processing to obtain the effective irradiance on modules. As a result, lower uncertainty in yield assessments can be expected.

14 SOLAR ENERGY↗

Porous electrodes for spectroelectrochemistry and x-ray structure analyses

An electrochemical cell that allows for in-situ structural characterization of amorphous thin film materials during the course of electrolysis using high-energy X-ray scattering (>50 keV). The compact and versatile cell employs a three-electrode configuration and minimizes X-ray scattering contributions from the cell, reference and counter electrodes, as well as the working electrode support. A large surface area working electrode has a physically robust support and is largely transparent to X-rays. This design, which utilizes a three-dimensional working electrode, also greatly improves the intensity and quality of the scattered signal compared to a two-dimensional working electrode. The in-situ cell can be used not only to investigate structural evolution during electrolysis using X-ray scattering (e.g. pair distribution function), but also to perform electrochemical potential-dependent structural analysis by extended X-ray absorption fine structure.

Kwon, Gihan↗

Performance Testing using Silicon Devices - Analysis of Accuracy: Preprint

Accurately determining PV module performance in the field requires accurate measurements of solar irradiance reaching the PV panel (i.e., Plane-of-Array - POA Irradiance) with known measurement uncertainty. Pyranometers are commonly based on thermopile or silicon photodiode detectors. Silicon detectors, including PV reference cells, are an attractive choice for reasons that include faster timeresponse (10 us) than thermopile detectors (1 s to 5 s), lower cost and maintenance. The main drawback of silicon detectors is their limited spectral response. Therefore, to determine broadband POA solar irradiance, a pyranometer calibration factor that converts the narrowband response to broadband is required. Normally this calibration factor is a single number determined under clear-skyconditions with respect to a broadband reference radiometer. The pyranometer is then used for various scenarios including varying airmass, panel orientation and atmospheric conditions. This would not be an issue if all irradiance wavelengths that form the broadband spectrum responded uniformly to atmospheric constituents. Unfortunately, the scattering and absorption signature varies widely withwavelength and the calibration factor for the silicon photodiode pyranometer is not appropriate for other conditions. This paper reviews the issues that will arise from the use of silicon detectors for PV performance measurement in the field based on measurements from a group of pyranometers mounted on a 1-axis solar tracker. Also we will present a comparison of simultaneous spectral andbroadband measurements from silicon and thermopile detectors and estimated measurement errors when using silicon devices for both array performance and resource assessment.

14 SOLAR ENERGY↗

Development and field testing of a rapid and ultra-stable atmospheric carbon dioxide spectrometer

We present field test results for a new spectroscopic instrument to measure atmospheric carbon dioxide (CO 2 ) with high precision (0.02 μmol mol -1 , or ppm at 1 Hz) and demonstrate high stability (within 0.1 ppm over more than 8 months), without the need for hourly, daily, or even monthly calibration against high-pressure gas cylinders. The technical novelty of this instrument (ABsolute Carbon dioxide, ABC) is the spectral null method using an internal quartz reference cell with known CO 2 column density. Compared to a previously described prototype, the field instrument has better stability and benefits from more precise thermal control of the optics and more accurate pressure measurements in the sample cell (at the mTorr level). The instrument has been deployed at a long-term ecological research site (the Harvard Forest, USA), where it has measured for 8 months without on-site calibration and with minimal maintenance, showing drift bounds of less than 0.1 ppm. Field measurements agree well with those of a commercially available cavity ring-down CO 2 instrument (Picarro G2301) run with a standard calibration protocol. This field test demonstrates that ABC is capable of performing high-accuracy, unattended, continuous field measurements with minimal use of reference gas cylinders.

Xiang, B.↗