Search NASA⌕ Search

SEARCH · Search NASA

Results for “reference site”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Rationale for a Mars Pathfinder mission to Chryse Planitia and the Viking 1 lander

Presently the landing site for Mars Pathfinder will be constrained to latitudes between 0 deg and 30 deg N to facilitate communication with earth and to allow the lander and rover solar arrays to generate the maximum possible power. The reference elevation of the site must also be below 0 km so that the descent parachute, a Viking derivative, has sufficient time to open and slow the lander to the correct terminal velocity. Although Mars has as much land surface area as the continental crust of the earth, such engineering constraints immediately limit the number of possible landing sites to only three broad areas: Amazonis, Chryse, and Isidis Planitia. Of these, both Chryse and Isidis Planitia stand out as the sites offering the most information to address several broad scientific topics.

Craddock, Robert A.↗
NASA NTRSDate not supplied

TPSAS-NF1676L-19788-DND

The calibration of the historical AVHRR visible channels has always been hindered by the degrading NOAA satellite orbits. The complete AVHRR record spans over three decades making it useful for cloud, aerosol, and land use climate studies. Studies that monitor long-term changes in these properties require climate quality calibration. The AVHRR sensors do not have any onboard visible calibration, unlike the IR channels. Many AVHRR post-launch calibration methods have been published. Some of these are based on the pseudo invariant targets such as desert and polar ice and others employ direct calibration transfer from a well-calibrated sensor such as MODIS. Most historical studies only employed only one method and reconciling calibration differences from multiple studies was difficult. This study employs multiple calibration approaches, which are then merged according to their individual uncertainty. Since the visible spectral response functions are similar across AVHRR sensor and that the morning and afternoon orbits usually degrade in the same manner, an afternoon and morning orbiter during the MODIS era is chosen as the reference AVHRR sensor. The reference AVHRR sensor is inter-calibrated with the Aqua-MODIS Collection 6 standard using simultaneous nadir overpass (SNO) radiance pairs. Three pseudo invariant target approaches are utilized, deserts, polar ice and deep convective clouds. These sites are characterized using reference AVHRR reflectances as a function of solar zenith angle. The multiple calibration approach is then validated with non-reference AVHRR sensor during the MODIS era, using AVHRR and MODIS SNO measurements. For historical AVHRR satellite having consistent calibration across invariant targets then validates the approach. This calibration effort is in sponsored by the NOAA CDR program to provide climate quality visible calibration coefficients to the remote sensing community. Each of the calibration approaches are unique and when utilized in tandem can accurately calibrate the AVHRR record. AVHRR calibration methods cannot rely on repeatable annual orbits for calibration model development. Inconsistent results prompt code and invariant target examinations that cannot be determined using only single method approaches. Results from this study will be presented at the meeting.

David Doelling↗
NASA NTRS2018

A Comparative Analysis of Micrometeorological Determinants of Evapotranspiration Rates Within a Heterogeneous Urban Environment

Variability in micrometeorological conditions and their influence on estimated reference evapotranspiration (RET) rates were evaluated across a heterogeneous urban environment. Micrometeorological data sets (incoming solar radiation, air temperature, relative humidity and wind speed) were collected over a one-year period at six weather stations in New York City, NY (USA). Weather stations are located at four new urban green space monitoring sites and two airports. Reference evapotranspiration (RET) rates were estimated from the micrometeorological data sets for a short reference surface at a daily time-step using the ASCE Standardized Reference Evapotranspiration Equation, a Penman-Monteith based combination equation. Nonparametric comparative statistical analyses (Kruskal-Wallis) revealed statistically significant differences (at significance level α = 0.05) in micrometeorological conditions and estimated RET rates between the six sites. On a cumulative annual basis, estimated RET varied by up to 40 percent between the sites. A new technique for adjusting weather data collected at one location (e.g. regional airports) for use at another location (e.g. interior engineered urban green spaces) was evaluated. The study highlights the importance, for accurate estimation of ET, of onsite micrometeorological data sets, but concludes that additional research is needed to more thoroughly characterize micrometeorological variability across heterogeneous urban environments, and also to evaluate the influence of non-meteorological determinants, e.g. vegetation type, soil/media type, media moisture conditions and anthropogenic heat fluxes, on urban ET.

Urban environment↗
NASA NTRS2010

International Space Station Mechanisms and Maintenance Flight Control Documentation and Training Development

International Space Station (ISS) crew and flight controller training documentation is used to aid in training operations. The Generic Simulations References SharePoint (Gen Sim) site is a database used as an aid during flight simulations. The Gen Sim site is used to make individual mission segment timelines, data, and flight information easily accessible to instructors. The Waste and Hygiene Compartment (WHC) training schematic includes simple and complex fluid schematics, as well as overall hardware locations. It is used as a teaching aid during WHC lessons for both ISS crew and flight controllers. ISS flight control documentation is used to support all aspects of ISS mission operations. The Quick Look Database and Consolidated Tool Page are imagery-based references used in real-time to help the Operations Support Officer (OSO) find data faster and improve discussions with the Flight Director and Capsule Communicator (CAPCOM). A Quick Look page was created for the Permanent Multipurpose Module (PMM) by locating photos of the module interior, labeling specific hardware, and organizing them in schematic form to match the layout of the PMM interior. A Tool Page was created for the Maintenance Work Area (MWA) by gathering images, detailed drawings, safety information, procedures, certifications, demonstration videos, and general facts of each MWA component and displaying them in an easily accessible and consistent format. Participation in ISS mechanisms and maintenance lessons, mission simulation On-the-Job Training (OJT), and real-time flight OJT was used as an opportunity to train for day-to-day operations as an OSO, as well as learn how to effectively respond to failures and emergencies during mission simulations and real-time flight operations.

Daugherty, Colin C.↗
NASA NTRS2021

A Method for Landsat and Sentinel 2 (HLS) BRDF Normalization

The Harmonized Landsat/Sentinel-2 (HLS) project aims to generate a seamless surface reflectance product by combining observations from USGS/NASA Landsat-8 and ESA Sentinel-2 remote sensing satellites. These satellites’ sampling characteristics provide nearly constant observation geometry and low illumination variation through the scene. However, the illumination variation throughout the year impacts the surface reflectance by producing higher values for low solar zenith angles and lower reflectance for large zenith angles. In this work, we present a model to derive the bidirectional reflectance distribution function (BRDF) normalization and apply it to the HLS product at 30m spatial resolution. It is based on the BRDF parameters estimated from the MODerate Resolution Imaging Spectroradiometer (MODIS) surface reflectance product (M{O,Y}D09) at 1 km spatial resolution using the VJB method (Vermote et al., 2009). Unsupervised classification (segmentation) of HLS images is used to disaggregate the BRDF parameters to the HLS spatial resolution and to build a BRDF parameters database at HLS scale. We first test the proposed BRDF normalization for different solar zenith angles over two homogeneous sites, in particular one desert and one Peruvian Amazon forest. The proposed method reduces both the correlation with the solar zenith angle and the coefficient of variation (CV) of the reflectance time series in the red and near infrared bands to 4% in forest and keeps a low CV of 3% to 4% for the deserts. Additionally, we assess the impact of the view zenith angle (VZA) in an area of the Brazilian Amazon forest close to the equator, where impact of the angular variation is stronger because it occurs in the principal plane. The directional reflectance shows a strong dependency with the VZA. The current HLS BRDF correction reduces this dependency but still shows an under-correction, especially in the near infrared, while the proposed method shows no dependency with the view angles. We also evaluate the BRDF parameters using field surface albedo measurements as a reference over seven different sites of the US surface radiation budget observing network (SURFRAD) and five sites of the Australian OzFlux network.

Belen Franch↗
NASA NTRSDate not supplied

Examination of L-Band Brightness Temperature Forecasts in the SMAP Level-4 Soil Moisture Analysis

The NASA Soil Moisture Active Passive (SMAP) mission [4] has been providing L-band (1.4 GHz) passive microwave brightness temperature (Tb) observations since April 2015. By assimilating the Tb observations into the NASA Catchment land surface model [5] using a spatially distributed ensemble Kalman filter, the NASA Global Modeling and Assimilation Office generates the SMAP Level-4 Soil Moisture (L4_SM) product, which provides global, 3-hourly, 9-km resolution estimates of surface (0-5 cm) and root-zone (0-100 cm) soil moisture with ~2.5-day latency for use in research and applications [6]. The L4_SM product also includes estimates of soil temperature, land surface fluxes, and assimilation diagnostics such as the model forecast and observed Tb values [7]. The output from the L4_SM system is routinely monitored by the L4_SM team. Such monitoring provides valuable information; instances of unusually large Tb observation-minus-forecast (O-F) residuals can indicate events during which soil moisture conditions are poorly described in the land modeling system [7,8]. For example, repeated occurrences of very large Tb O-F values in central Australia were traced back to deficiencies in the gauge-based precipitation product used in the land modeling system through L4_SM Version 5; this discovery prompted the use, beginning in Version 6, of satellite- and gauge-based precipitation observations outside of North America [9]. Recently, a statistical analysis of the Tb O-F residuals revealed systematic errors in the “tau-omega” L-band radiative transfer model that converts the land-model simulated soil moisture and temperature into the forecast Tb prior to the L4_SM analysis. The L4_SM analysis is built on the ensemble Kalman filter and assumes unbiased forecast errors. The presence of systematic Tb forecast errors could thus adversely impact the quality of the analyzed soil moisture. In this paper, we examine the Tb O-F residuals of the latest Version 7 L4_SM data (Science Version ID Vv7030 and Vv7032) [10,11,12]. In the L4_SM Version 7 algorithm, key parameters of the L-band radiative transfer model, including soil roughness, scattering albedo, and a (seasonally varying) climatology of vegetation opacity, are obtained from the SMAP Level-2 Radiometer retrieval product (Version 5) [1]. Additionally, we also use ground measurements of surface soil moisture and soil temperature from the SMAP core validation sites as in situ reference of soil conditions [2,3]. As part of the L4_SM system calibration, the seasonally-varying bias between the model forecast Tb and the observed values is removed prior to the assimilation of the SMAP Tb observations [7]. That is, the L4_SM system is designed to only correct errors in synoptic-scale and interannual variations from the long-term mean seasonal cycle while maintaining the model’s (potentially erroneous) climatology. The Tb O-F residuals examined here are thus computed using SMAP Tb observations after they are rescaled to the mean seasonal cycle of Tb from the modeling system without SMAP data assimilation. Consequently, the long-term average of the Tb O-F residuals has a global mean of only 0.13 K and locally small values, ranging from -1 to 3 K. Despite the small time-average values of the Tb O-F residuals, the model forecast Tb was nevertheless found to exhibit undesirable systematic errors. At some locations, the time-average Tb O-F values strongly depend on surface soil moisture (SM). At the Yanco SMAP core validation site, for example, the Tb O-F residuals typically range from 5 to 15 K under dry soil moisture conditions (SM < 0.15 m3 m-3) yet are predominantly negative under wet soil moisture conditions (SM > 0.25 m3 m-3), with values ranging from 0 to -40 K. This results in soil moisture analysis increments that persistently make the soil drier under dry SM conditions and persistently make the soil wetter under wet SM conditions, suggesting an error in the dynamic range of the simulated Tb, soil moisture or soil temperature. In this paper, we describe the higher-order systematic Tb forecast errors in more detail, examine their impact on the L4_SM product quality, and explore potential avenues to further improve the L4_SM algorithm.

Rolf Reichle↗
NASA NTRS1973

Seismic analysis of nuclear power plant structures

Primary structures for nuclear power plants are designed to resist expected earthquakes of the site. Two intensities are referred to as Operating Basis Earthquake and Design Basis Earthquake. These structures are required to accommodate these seismic loadings without loss of their functional integrity. Thus, no plastic yield is allowed. The application of NASTRAN in analyzing some of these seismic induced structural dynamic problems is described. NASTRAN, with some modifications, can be used to analyze most structures that are subjected to seismic loads. A brief review of the formulation of seismic-induced structural dynamics is also presented. Two typical structural problems were selected to illustrate the application of the various methods of seismic structural analysis by the NASTRAN system.

Go, J. C.↗
NASA NTRS1979

Precise time and Time Interval (PTTI) measurements from the navigation technology satellites and the GPS NAVSTAR-4 satellite

A time domain estimate for the NAVSTAR-4 SV clock offset was obtained for each SV pass over the GPS monitor sites, using a smoothed reference ephemeris, with corrections for ionospheric delay, tropospheric delay, earth rotation and relativistic effects. Conversion from the time domain to the frequency domain was made using the two sample Allan Variance; sigma-tau plots used to identify the noise processes. Estimates of flicker and white frequency noise for the NAVSTAR-4 rubidium frequency standard were obtained. The contribution of the reference ground clocks and other error sources to the frequency stability estimates were also considered.

Buisson, J. A.↗
NASA NTRS1984

Mobile spectrometer measures radar backscatter

The present article is concerned with a helicopter-borne spectrometer (Heloscat), which has been developed to permit high-quality scattering measurements from a mobile platform at remote sites. The term 'spectrometer' referes to a class of scatterometers. The term 'scatterometer' is employed to denote a specialized radar for measuring scattering coefficients as a function of angle. A spectrometer, on the other hand, is a scatterometer which can measure backscatter at several frequencies. The Heloscat system is discussed, taking into account two antennas, RF hardware, and an externally mounted pendulum for angle encoding. A dual-antenna configuration is used for cross-polarized measurements, while a single-antenna system is used for like-polarized measurements. Attention is also given to oscillator characteristics, efficient data handling, and aspects of calibration.

Gogineni, S.↗
NASA NTRS1987

Users of middle atmosphere models remarks

The procedure followed for shuttle operations is to calculate descent trajectories for each potential shuttle landing site using the Global Reference Atmosphere Model (GRAM) to interactively compute density along the flight path 100 times to bound the statistics. The purpose is to analyze the flight dynamics, along with calculations of heat loads during reentry. The analysis program makes use of the modified version of the Jacchia-70 atmosphere, which includes He bulges over the poles and seasonal latitude variations at lower altitudes. For the troposphere, the 4-D Model is used up to 20 km, Groves from 30 km up to 90 km. It is extrapolated over the globe and faired into the Jacchia atmosphere between 90 and 115 km. Since data on the Southern Hemisphere was lacking, what was done was that the data was flipped over and lagged 6 months. Sometimes when winds are calculated from pressure data in the model there appear to be discontinuities. Modelers indicated that the GRAM was not designed to produce winds, but good wind data is needed for the landing phase of shuttle operations. Use of atmospheric models during reentry is one application where it is obvious that a single integrated atmosphere model is required.

Gamble, Joe↗
NASA NTRS1993

Rate determination from vector observations

Vector observations are a common class of attitude data provided by a wide variety of attitude sensors. Attitude determination from vector observations is a well-understood process and numerous algorithms such as the TRIAD algorithm exist. These algorithms require measurement of the line of site (LOS) vector to reference objects and knowledge of the LOS directions in some predetermined reference frame. Once attitude is determined, it is a simple matter to synthesize vehicle rate using some form of lead-lag filter, and then, use it for vehicle stabilization. Many situations arise, however, in which rate knowledge is required but knowledge of the nominal LOS directions are not available. This paper presents two methods for determining spacecraft angular rates from vector observations without a priori knowledge of the vector directions. The first approach uses an extended Kalman filter with a spacecraft dynamic model and a kinematic model representing the motion of the observed LOS vectors. The second approach uses a 'differential' TRIAD algorithm to compute the incremental direction cosine matrix, from which vehicle rate is then derived.

Weiss, Jerold L.↗
NASA NTRS1994

Reverse Polarity Magnetized Melt Rocks from the Cretaceous/Tertiary Chicxulub Structure, Yucatan Peninsula, Mexico

We report paleomagnetic results for core samples of the breccia and andesitic rocks recovered from the Yucatan-6 Petrolcos Mexicanos exploratory well within the Chicxulub structure (about 60 km SSW from its center), northern Yucatan, Mexico. A previous study has shown that the rocks studied contain high iridium levels and shocked breccia clasts and an Ar/Ar date of 65.2 +/- 0.4 Ma. Andesitic rocks are characterized by stable single-component magnetizations with a mean inclination of -42.6 deg +/- 2.4 deg. Breccias present a complex paleomagnetic record characterized by multivectorial magnetizations with widely different initial NRM inclinations. However, after alternating field demagnetization, well defined characteristic components with upward inclinations are defined. IRM acquisition experiments, comparison of IRM and NRM coercivity spectra and the single component magnetization of the andesitic rocks indicate the occurrence of iron-rich titanomagnetites of single or pseudo-single domain states as the dominant magnetic carriers. Mean inclinations from the andesitic rocks and most of the breccia samples give a mean inclination of about -40 deg to -45 deg, indicating a reverse polarity for the characteristic magnetization that is consistent with geomagnetic chron 29R, which spans the Cretaceous/Tertiary (K/T) boundary. The inclination is also consistent with the expected value (and corresponding paleolatitude) for the site estimated from the reference polar wander curve for North America. We suggest that the characteristic magnetizations for the andesitic and breccia rocks are the result of shock heating at the time of formation of the impact structure and that the age, polarity and pateolatitude are consistent with a time at the K/T boundary.

Urrutia-Fucugauchi, J.↗
NASA NTRS1997

Global Plate Velocities from the Global Positioning System

We have analyzed 204 days of Global Positioning System (GPS) data from the global GPS network spanning January 1991 through March 1996. On the basis of these GPS coordinate solutions, we have estimated velocities for 38 sites, mostly located on the interiors of the Africa, Antarctica, Australia, Eurasia, Nazca, North America, Pacific, and South America plates. The uncertainties of the horizontal velocity components range from 1.2 to 5.0 mm/yr. With the exception of sites on the Pacific and Nazca plates, the GPS velocities agree with absolute plate model predictions within 95% confidence. For most of the sites in North America, Antarctica, and Eurasia, the agreement is better than 2 mm/yr. We find no persuasive evidence for significant vertical motions (less than 3 standard deviations), except at four sites. Three of these four were sites constrained to geodetic reference frame velocities. The GPS velocities were then used to estimate angular velocities for eight tectonic plates. Absolute angular velocities derived from the GPS data agree with the no net rotation (NNR) NUVEL-1A model within 95% confidence except for the Pacific plate. Our pole of rotation for the Pacific plate lies 11.5 deg west of the NNR NUVEL-1A pole, with an angular speed 10% faster. Our relative angular velocities agree with NUVEL-1A except for some involving the Pacific plate. While our Pacific-North America angular velocity differs significantly from NUVEL-1A, our model and NUVEL-1A predict very small differences in relative motion along the Pacific-North America plate boundary itself. Our Pacific-Australia and Pacific- Eurasia angular velocities are significantly faster than NUVEL-1A, predicting more rapid convergence at these two plate boundaries. Along the East Pacific Pise, our Pacific-Nazca angular velocity agrees in both rate and azimuth with NUVFL-1A.

Larson, Kristine M.↗
NASA NTRS1998

Summary of Proton Test on the Quick Logic QL3025 at Indiana University

This issue of the Programmable Logic Application Notes is a compilation of topics: (1) Proton irradiation tests were performed on the Quick Logic QL3025 at the Indian University Cyclotron facility. The devices, tests, and results are discussed; (2) The functional failure of EEPROM's in heavy ion environment is presented; (3) the Act 1 architecture is summarized; (4) Antifuse hardness and hardness testing is updated; the single even upset (SEU) response of hardwired flip-flops is also presented; (4) Total dose results of the ACT 2 and ACT 3 circuits is presented in a chart; (5) Recent sub-micron devices testing of total dose is presented in a chart along with brief discussion; and (6) a reference to the WWW site for more articles of interest.

Katz, Richard↗
NASA NTRS2018

Development of a Coherent Doppler Lidar for Precision Maneuvering and Landing of Space Vehicles

A coherent Doppler lidar has been developed to address NASA’s need for a high-performance, compact, and cost-effective velocity and altitude sensor onboard its landing vehicles. Future robotic and manned missions to planetary bodies require precise ground-relative velocity vector and altitude data to execute complex descent maneuvers and safe, soft landing at a pre-designated site. This lidar sensor, referred to as a Navigation Doppler Lidar, meets the required performance of landing missions while complying with vehicle size, mass, and power constraints. Operating from over five kilometers altitude, the lidar obtains velocity and range precision measurements with 2 cm/sec and 2 meters, respectively, dominated by the vehicle motion. After a series of flight tests onboard helicopters and rocket-powered free-flyer vehicles, the Navigation Doppler Lidar is now being ruggedized for future missions to various destinations in the solar system.

Amzaherdian, Farzin↗
NASA NTRS2020

Corrosion Atmospheric Exposure Facility PRL #239 SWMU Assessment Report/Confirmation Sampling Work Plan

The National Aeronautics and Space Administration (NASA) Resource Conservation and Recovery Act (RCRA) permit requires identification and evaluation of known Solid Waste Management Units (SWMU) located at the Kennedy Space Center (KSC). The Corrosion Atmospheric Exposure Facility (CAEF), also known as facility number K8-0600, and the Corrosion Test Area (CTA); also known as facility number K8-0237, herein referred to as the site, is designated Potential Release Location (PRL) 239 under the NASA RCRA permit. A SWMU Assessment (SA) was conducted between November 2019 and February 2020 to identify potential environmental impacts related to current and historic operations being conducted at the site. The SA included a site reconnaissance visit in February 2020, interviews with various personnel possessing knowledge of past work practices and operations at the site, and review of available historical documentation, engineering drawings, and facility inspection reports. Current site conditions were documented in photographs. Soil types and wildlife habitat were also evaluated. The objective of the assessment was to identify potential locations of concern (LOC) at the site and to determine whether further evaluation is required.

Kimberly Clower↗
NASA NTRSDate not supplied

Navigation Doppler Lidar

A Doppler lidar has been developed by NASA as an alternative to radars for providing velocity and altitude data to landing vehicles. Future robotic and manned missions to planetary bodies demand precise ground-relative velocity vector and altitude data to execute complex descent maneuvers for safe, soft and pinpoint landing at a pre-designated site. This lidar sensor, referred to as Navigation Doppler Lidar (NDL), provides velocity and altitude data from over five kilometers altitude to within a few cm/sec and tens of centimeters precision, respectively. NDL technology will be demonstrated on two lunar landing missions this year that will serve as precursors for large robotic and manned landing missions to the Moon, Mars, and other solar system destinations. NDL can also benefit terrestrial aerial vehicles that cannot rely on the GPS for position and velocity data or require precision data relative to local ground.

Doppler Lidar↗
NASA NTRS2024

San José Urban Development: Quantifying Canopy Cover and Land Surface Temperature in San José to Identify Future Tree Planting Sites

The urban heat island effect refers to the phenomenon of substantially increased temperatures in urban areas compared to their surrounding suburban or rural counterparts. The City of San José’s Department of Parks, Recreation and Neighborhood Services (PRNS) and Department of Transportation (DOT) work to mitigate the UHI effect through urban forestry initiatives. The PRNS and DOT partnered with NASA DEVELOP to identify areas in need of tree plantings. We examined land surface temperature (LST) throughout the city using data from the Thermal Infrared Sensor (TIRS) and TIRS-2 on NASA’s Landsat 8 and 9 satellites from 2013 to 2024. We also assessed canopy cover in parks using LiDAR data collected in 2020 for the United States Geological Survey’s 3D Elevation Program, and measured vegetation greenness using the Normalized Difference Vegetation Index (NDVI) with PlanetScope imagery from 2018 to 2024. We evaluated social and environmental factors that influence the distribution of heat event impacts by creating a heat vulnerability index. We found that heat is concentrated in urban areas and that poor vegetation health is associated with high LST. We also found that socially vulnerable communities are disproportionately located in areas of high environmental risk. These analyses allow the partners to prioritize tree plantings in parks near areas of high social and environmental risk. We determined that Earth observations can be used to inform urban forestry decision making, but because methodologies for using LiDAR to assess canopy cover vary greatly, it is difficult to make comparisons across different canopy cover assessments.

land surface temperature↗