SEARCH · Search NASA

Results for “retention”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

DOE OSTI2021

Ferroelectric polarization retention with scaling of Hf 0.5 Zr 0.5 O 2 on silicon

In this paper, we investigate the polarization retention of Hf 0.5 Zr 0.5 O 2 (HZO)-based metal–ferroelectric–insulator–Si (MFIS) capacitors with scaling of the ferroelectric (FE) layer thickness from 5 nm to 20 nm. The capacitors have a constant interface layer capacitance of ~24 μF/cm 2 , developed due to the integration of HZO on a degenerated Si as a bottom conducting electrode. It is observed that 20 nm HZO films show a small change (~5%) in FE polarization (P FE ) between short (10 μs) and long (6 s) retention time, while 5-nm-thick films exhibit a large difference (~90%). Furthermore, the dependence of P FE retention loss on the FE thickness can be understood by the presence of a built-in electric field in the FE layer, generated due to charge continuity between the FE and the interface layers in the ground state without any external bias. A direct experimental observation also confirms that a residual voltage is developed at the node between the metal–ferroelectric–metal and metal–oxide–semiconductor capacitors connected in series, in the ground state with zero external bias. It is expected that a proper understanding of the built-in field developed in the FE layer in an MFIS stack is crucial for FE memory retention characteristics.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Exceptional high temperature retention in Al 0.93 B 0.07 N films

This paper reports the retention behavior for Al 0.93 B 0.07 N thin films, a member of the novel family of wurtzite ferroelectrics. Our experiments suggest that bipolar cycling of metal (Pt/W)/Al 0.93 B 0.07 N/W/Al 2 O 3 film stacks first induced wake-up and then a region of constant switchable polarization. Here, the films showed excellent retention of the stored polarization state. As expected, data retention was slightly inferior in the opposite state (OS) measurements. However, it is noted that even after 3.6 × 10 6 s (1000 h) at 200 °C, the OS signal margin still exceeded 200 μC/cm 2 . The predicted OS retention is 82% after 10 yr baking at 200 °C.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Total-Ionizing-Dose Effects on Long-term Data Retention Characteristics of Commercial 3-D NAND Memories

This article evaluates the data retention characteristics of irradiated multi-level cell (MLC) 3-D NAND flash memories. We irradiate the memory chips by a Co-60 gamma-ray source for up to 50 krad(Si) and then write a random data pattern on the irradiated chip to find its retention characteristics. The experimental results show that the data retention property of the irradiated chips is significantly degraded compared to the un-irradiated ones. We evaluate two independent strategies to improve the data retention characteristics of the irradiated chips. Furthermore, the first method involves high-temperature annealing of the irradiated chip while the second method suggests pre-programming the memory modules before deploying them in radiation-prone environments.

3-D NAND flash↗

DOE OSTI2021

Exploiting user activeness for data retention in HPC systems

HPC systems typically rely on the fixed-lifetime (FLT) data retention strategy, which only considers temporal locality of data accesses to parallel file systems. However, our extensive analysis based on the leadership-class HPC system traces suggests that the FLT approach often fails to capture the dynamics in users' behavior and leads to undesired data purge. In this study, we propose an activeness-based data retention (ActiveDR) solution, which advocates considering the data retention approach from a holistic activeness-based perspective. By evaluating the frequency and impact of users' activities, ActiveDR prioritizes the file purge process for inactive users and rewards active users with extended file lifetime on parallel storage. Our extensive evaluations based on the traces of the prior Titan supercomputer show that, when reaching the same purge target, ActiveDR achieves up to 37% file miss reduction as compared to the current FLT retention methodology.

Zhang, Wei↗

DOE OSTI2023

Literature Review and Experimental Observations of the Effects of Salinity, Hardness, Lithology, and ATBS Content on HPAM Polymer Retention for the Milne Point Polymer Flood

Summary At the Milne Point polymer flood (North Slope of Alaska), polymer retention is dominated by the clay, illite. Illite, and kaolinite cause no delay in polymer propagation in Milne Point core material, but they reduce the effective polymer concentration and viscosity by a significant amount (e.g., 30%), thus reducing the efficiency of oil displacement until the full injected polymer concentration is regained [which requires several pore volumes (PVs) of throughput]. This work demonstrates that polymer retention on illite is not sensitive to monovalent ion concentration, but it increases significantly with increased divalent cation concentration. The incorporation of a small percentage of acrylamido tertiary butyl sulfonic acid (ATBS) monomers into hydrolyzed polyacrylamide (HPAM) polymers is shown to dramatically reduce retention. The results are discussed in context with previous literature reports. Bridging adsorption was proposed as a viable mechanism to explain our results. Interestingly, an extensive literature review reveals that polymer retention (on sands and sandstones) is typically only modestly sensitive to the presence of oil. Extensive examination of the literature on inaccessible pore volume (IAPV) suggests the parameter was commonly substantially overestimated, especially in rock/sand more permeable than 500 md (which comprises the vast majority of existing field polymer floods).

Engineering↗

DOE OSTI2023

Enhanced Tritium Retention in LiAlO2 Pellets via Engineered Glazes: Tritium Science Project

This project investigated the impact of adding a thin (10 – 50 µm) layer of amorphous glaze to the surface of a TPBAR pellet on its retention of helium, hydrogen (as a surrogate for tritium), and water (as a surrogate for tritiated water). The hypothesis was that the glaze would significantly reduce permeation of hydrogen species with a lesser impact on hindering helium permeation. A non-crystallizing soda-lime-silicate glass, known as SCN-1, was selected for this proof-of-concept study. It was found that continuous glaze layers of the desired thickness could be applied to the pellets with two or more dip coats, depending on the targeted thickness. At 330°C, the glaze was found to have a permeability that was lower than that of the pellet by a factor of ~10 6 , implying that a thin 10 – 50 µm layer can significantly increase pellet retention of hydrogen. Meanwhile, the permeation rate of helium through the glaze was found to be ~20 times higher than that of hydrogen or water. An unanticipated outcome of the study was that unglazed pellets were measured to have hydrogen diffusivities that are a factor of ~105 greater than the diffusivity value used in the TPBAR COMSOL model to achieve observed tritium retention rates. When the higher measured diffusivity was substituted into the model and the model was run with all tritium species in the pellet in the form of T 2 O at a partial pressure of 20 Pa in equilibrium with LiOT, the resulting retention was 50% after 500 days.

36 MATERIALS SCIENCE↗

NASA NTRS1984

Fastener load tests and retention systems tests for cryogenic wind-tunnel models

A-286 stainless steel screws were tested to determine the tensile load capability and failure mode of various screw sizes and types at both cryogenic and room temperature. Additionally, five fastener retention systems were tested by using A-286 screws with specimens made from the primary metallic alloys that are currently used for cryogenic models. The locking system effectiveness was examined by simple no-load cycling to cryogenic temperatures (-275 F) as well as by dynamic and static loading at cryogenic temperatures. In general, most systems were found to be effective retention devices. There are some differences between the various devices with respect to ease of application, cleanup, and reuse. Results of tests at -275 F imply that the cold temperatures act to improve screw retention. The improved retention is probably the result of differential thermal contraction and/or increased friction (thread-binding effects). The data provided are useful in selecting screw sizes, types, and locking devices for model systems to be tested in cryogenic wind tunnels.

Wallace, J. W.↗

NASA NTRS1994

Thermocapillary flow with evaporation and condensation and its effect on liquid retention in low-G fluid acquisition devices

The steady motion, thermal and free surface behavior of a volatile, wetting liquid in microgravity are studied using scaling and numerical techniques. The objective is to determine whether the thermocapillary and two-phase convection arising from thermodynamic nonequilibrium along the porous surfaces of spacecraft liquid acquisition devices could cause the retention failures observed with liquid hydrogen and heated vapor pressurant. Why these devices seem immune to retention loss when pressurized with heated helium or heated directly through the porous structure was also examined. Results show that highly wetting fluids exhibit large negative and positive dynamic pressure gradients towards the meniscus interline when superheated and subcooled, respectively. With superheating, the pressure variation and recoil force arising from liquid/vapor phase change exert the same influence on surface morphology and promote retention. With subcooling, however, the pressure distribution produces a suction that degrades mechanical equilibrium of the surface. This result indicates that thermocapillary-induced deformation arising from subcooling and condensation is the likely cause for retention loss. In addition, increasing the level of nonequilibrium by reducing accommodation coefficient suppresses deformation and explains why this failure mode does not occur in instances of direct screen heating or pressurization with a heated inert gas.

Schmidt, George R.↗

NASA NTRS2017

The Effects of Long-Duration Spaceflight on Training Retention and Transfer

Training our crew members for long duration, exploration-class missions will have to maximize long-term retention and transfer of the trained skills. The expected duration of the missions, our inability to predict all the possible tasks the crew will be called upon to perform, and the low training-to-mission time ratio require that the training be maximally effective such that the skills acquired during training will be retained and will be transferrable across a wide range of specific tasks that are different from the particular tasks used during training. However, to be able to design training that can achieve these ambitious goals, we must first understand the ways in which long-duration spaceflight affects training retention and transfer. Current theories of training retention and transfer are largely based on experimental studies conducted at university laboratories using undergraduate students as participants. Furthermore, all such studies have been conducted on Earth. We do not know how well the results of these studies predict the performance of crew members. More specifically, we do not know how well the results of these studies predict the performance of crew members in space and especially during long-duration missions. To address this gap in our knowledge, the current on-going study seeks to test the null hypothesis that performance of university undergraduate students on Earth on training retention and transfer tests do in fact predict accurately the performance of crew members during long-duration spaceflights. To test this hypothesis, the study employs a single 16-month long experimental protocol with 3 different participant groups: undergraduate university students, crew members on the ground, and crew members in space. Results from this study will be presented upon its completion. This poster presents results of study trials of the two tasks used in this study: a data entry task and a mapping task. By researching established training principles, by examining future needs, and by using current practices in spaceflight training as test beds, this research project is mitigating program risks and generating templates and requirements to meet future training needs.

ISS↗

DOE OSTI2021

Comparative study of surface modification and D retention between beryllium and beryllides under high flux plasma exposure

The microstructures and deuterium (D) retention properties were investigated for beryllium intermetallic compounds (beryllides), such as Be 12 Ti and Be 12 V, compared to pure beryllium (Be), exposed to high density pure D and helium (He) mixed plasmas. TEM cross-sectional observations revealed the formation of cone structures on the Be surface exposed to the plasmas at a moderate temperature of 573 K. The crystal structure of the cones and the mass loss caused by the plasma exposure implied that the cone structures were generated by sputtering. The Ti or V surface enrichment was observed on both beryllides with no cone structures developed. TDS measurements indicated that He seeding to D plasma caused a ~ 4 times reduction of the D retention for both beryllides, while no reduction was observed for Be. As a result, the beryllide samples exposed to D + He mixture plasmas showed a lower total D retention than in Be.

Hydrogen retention↗

DOE OSTI2026

Cr plasma-material-interaction in PISCES-RF: D thermal release, retention, and erosion

Pure chromium (Cr) targets were exposed to high-flux deuterium (D) plasmas in the Pisces-RF linear plasma device, and measurements of D retention, release, and erosion were subsequently performed. Post-exposure D retention was quantified using temperature-programmed desorption on Cr targets irradiated by 50 eV ions over a broad range of exposure temperatures (423–873 K) and ion fluences (3 × 10 24 – 3 × 10 26 m −2 ). The retained D inventory was observed to decrease rapidly with increased exposure temperature, from approximately ∼7 × 10 20 m −2 at ∼ 420 K, to then saturate near ∼ 10 20 m −2 for exposure temperatures above ∼550 K. Separately, at fixed exposure temperature (∼450 K), D retention was found to have only a weak dependence on increasing ion fluence. Lastly, the erosion of Cr in D plasma was investigated for ion impact energies in the range 40 ≤ E i ≤ 250 eV. Erosion was inferred using optical emission spectroscopy (OES) from the ratio of emission lines (Cr I (425.4 nm)/D I (656.1 nm)) measured close to the target. Conversion of the OES yield data to net erosion yield was made with singular ion energy target mass-loss measurements. These net erosion yield data were then further corrected to obtain gross erosion yield by accounting for a re-deposition factor, computed using a simple model. The gross erosion yield is found to be 2–4 times lower than predicted by SDTrimSP, consistent with that typically observed for light-ion sputtering under high-flux plasma conditions.

Chromium↗

DOE OSTI2021

Contributions of biofilm-induced flow heterogeneities to solute retention and anomalous transport features in porous media

We report that microbial biofilms are ubiquitous within porous media and the dynamics of their growth influence surface and subsurface flow patterns which impacts the physical properties of porous media and large-scale transport of solutes. Here, a two-dimensional pore-scale numerical model was used to evaluate the impact of biofilm-induced flow heterogeneities on conservative transport. Our study integrates experimental biofilm images of Paenibacillus 300A strain in a microfluidic device packed with cylindrical grains in a hexagonal distribution, with mathematical modeling. Biofilm is represented as a synthetic porous structure with locally varying physical properties that honors the impact of biofilm on the porous medium. We find that biofilm plays a major role in shaping the observed conservative transport dynamics by enhancing anomalous characteristics. More specifically, when biofilm is present, the pore structure in our geometry becomes more spatially correlated. We observe intermittent behavior in the Lagrangian velocities that switches between fast transport periods and long trapping events. Our results suggest that intermittency enhances solute spreading in breakthrough curves which exhibit extreme anomalous slope at intermediate times and very marked late solute arrival due to solute retention. The efficiency of solute retention by the biofilm is controlled by a transport regime which can extend the tailing in the concentration breakthrough curves. These results indicate that solute retention by the biofilm exerts a strong control on conservative solute transport at pore-scale, a role that to date has not received enough attention.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2020

In-Operando Study of Shape Retention and Microstructure Development in a Hydrolyzing Sol–Gel Ink during 3D-Printing

3D printing of amorphous and crystalline ceramics is of paramount importance for the fabrication of a wide range of devices with applications across different technology fields. Printed ceramics are remarkably enabled by the sol-gel synthesis method in conjunction with continuous filament direct ink writing. During printing, multiple processes contribute to the evolution of inks including shape retention, chemical conversion, solidification, and microstructure formation. Traditionally, depending on the ink composition and printing environment, several mechanisms have been associated with the shape retention and solidification of 3D printed structures: gelation, rapid solvent evaporation, energy-driven phase transformation, and chemical-driven phase transformation. Understanding the fundamental differences between these mechanisms becomes key since they strongly influence the spatiotemporal evolution of the materials, as the out-of-equilibrium processes inherent to the extrusion, relaxation, and solidification of printed materials have significant effects on the materials properties. Herein, we investigate the shape retention mechanism and the hydrolysis-induced material conversion and microstructure formation during the 3D printing of a water reactive sol-gel ink that transforms into titanium dioxide-based ceramic. This study aims at identifying characteristic mechanisms associated with the material transformation, establishing connections between the microstructure development and the timescales associated with solidification under operando 3D-printing conditions. The investigation of this material's out-of-equilibrium pathways under processing conditions is enabled by time-resolved coherent X-ray scattering, providing simultaneous access to temporospatially resolved microstructural and dynamics information. Furthermore, we explore X-ray speckle tracking as a tool to resolve deformations of the microstructure in a printed filament associated with the deposition of consecutive filaments. Through this work, we aim at providing a fundamental understanding of the relationships behind these transformative processes in 3D printing and their timescales as the basis for achieving unprecedented control over printed materials microstructure.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Improved scaling law for the prediction of deuterium retention in beryllium co-deposits

Hydrogen isotope co-deposition with Be eroded from the first wall is expected to be the main fusion fuel retention mechanism in ITER. Since good fuel accounting is crucial for economic and safety reasons, reliable predictions of hydrogen isotope retention are needed. Furthermore, this study builds upon the well-established empirical De Temmerman scaling law that predicts D/Be ratios in co-deposited layers based on deposition temperature, deposition rate, and deuterium particle energy. Expanding the data used in the original development of the scaling law with an additional dataset obtained with more recent measurements using a different technique to the original De Temmerman approach, allows us to obtain new values for free parameters and improve the prediction capabilities of the new scaling law. In an effort to improve the model even further, scaling with D 2 background pressure was included and a new two-term model derived, describing D retention in low- and high-energy traps separately.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS2017

Environmental Effects on Data Retention in Flash Cells

Flash technology is being utilized in fuzed munition applications and, based on the development of digital logic devices in the commercial world, usage of flash technology will increase. Antifuse technology, prevalent in non-volatile field programmable gate arrays (FPGAs), will eventually be phased out as new devices have not been developed for approximately a decade. The reliance on flash technology presents a long-term reliability issue for both DoD and NASA safety- and mission-critical applications. A thorough understanding of the data retention failure modes and statistics associated with Flash data retention is of vital concern to the fuze safety community. A key retention parameter for a flash cell is the threshold voltage (VTH), which is an indirect indicator of the amount of charge stored on the cells floating gate. This paper will present the results of our on-going tests: long-term storage at 150 C for a small population of devices, neutron radiation exposure, electrostatic discharge (ESD) testing, and the trends of large populations (over 300 devices for each condition) exposed to three difference temperatures: 25 C, 125 C, and 150 C.

Flash↗

DOE OSTI2021

Deuterium permeation and retention in 316L Stainless Steel Manufactured by Laser Powder Bed Fusion

Deployment of additively manufactured materials into nuclear energy systems requires investigation of the full range of the unique environmental effects on these materials. Hydrogen isotopes are common gaseous species in nuclear reactors and exhibit ample high mobility in most materials. While hydrogen isotopes mobility in wrought stainless steel is well understood, this property is not thoroughly studied for its additively manufactured variants. In this study, we investigated the deuterium permeation and retention in 316L stainless steel manufactured by laser powder bed fusion. The results showed that the deuterium permeability in the as-built additively manufactured 316L stainless steel (AM SS316L) is greater than that of the reference wrought 316L stainless steel by a factor of 2.8. However, the stress-relieved and solution-annealed AM SS316L samples exhibit lower deuterium permeability in comparison with the as-built condition. Following the solution annealing, the deuterium permeability of AM SS316L is comparable with that of the reference wrought SS316L. Deuterium retention in the as-built AM SS316L is 45% higher than that of the wrought 316L stainless steel and slightly higher than that of the two thermally annealed AM SS316L materials. Finally, transmission electron microscopy and positron annihilation lifetime spectroscopy were used to obtain microstructural information used to determine deuterium permeation and retention behavior in the studied materials.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Molecular homing and retention of muscle membrane stabilizing copolymers by non-invasive optical imaging in vivo

First-in-class membrane stabilizer Poloxamer 188 (P188) has been shown to confer membrane protection in an extensive range of clinical conditions; however, elements of the systemic distribution and localization of P188 at the organ, tissue, and muscle fiber levels in vivo have not yet been elucidated. Here we used non-invasive fluorescence imaging to directly visualize and track the distribution and localization of P188 in vivo. The results demonstrated that the Alx647 probe did not alter the fundamental properties of P188 to protect biological membranes. Distribution kinetics in mdx mice demonstrated that Alx647 did not interface with muscle membranes and had fast clearance kinetics. In contrast, the distribution kinetics for P188-Alx647 was significantly slower, indicating a dramatic depot and retention effect of P188. Results further demonstrated the significant retention of P188-Alx647 in the skeletal muscle of mdx mice, showing a significant genotype effect with a higher fluorescence signal in the mdx muscles over BL10 mice. High-resolution optical imaging provided direct evidence of P188 surrounding the sarcolemma of skeletal and cardiac muscle cells. Taken together, these findings provide direct evidence of muscle-disease-dependent molecular homing and retention of synthetic copolymers in striated muscles thereby facilitating advanced studies of copolymer-membrane association in health and disease.

60 APPLIED LIFE SCIENCES↗

DOE OSTI2020

Tritium generation, release, and retention from in-core fluoride salt irradiations

Further understanding of tritium transport mechanisms in the combined molten fluoride salt and graphite environment is necessary for the design and licensing of a Fluoride-Salt-Cooled High-Temperature Reactor (FHR). The three in-core fluoride salt irradiations completed at the Massachusetts Institute of Technology Reactor (MITR) are a useful parallel for studying transport phenomena expected in a FHR environment. During the irradiations, evolution of tritium from the flibe salt was monitored and compared to the calculated total generation rate. A difference of 22 ± 10% between the integrated calculated tritium generation rate and the total release was measured for the third MITR irradiation (FS-3). The fraction of tritium which was not released from the salt could be explained by tritium retention in graphite. Additionally, for post irradiation examination, a thermal desorption furnace was used to heat nuclear graphite samples in order to release and measure retained tritium. The desorption analysis in this work utilized seven subsections of graphite from the second salt irradiation (FS-2); three from a disc of IG-110U and four from ARB matrix graphite. Observed desorption versus temperature as well as total tritium content in the samples after irradiation indicate that the graphites were not volumetrically saturated with tritium, but rather tritium retention was likely limited to the near-surface region. Measurements of the samples resulted in 2.90 ± 0.29 μCi/mm 2 of tritium retained by IG-110U and 1.83 ± 0.31 μCi/mm 2 for ARB during the 300 h FS-2 in-core irradiation. Based on the desorption measurements, the estimated total tritium retention in graphite from the FS-2 samples is consistent with the tritium release measurements from the FS-3 experiment.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗