Search NASA⌕ Search

SEARCH · Search NASA

Results for “rough fractures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Direct Ink Write 3D Printing of Fully Dense and Functionally Graded Liquid Metal Elastomer Foams

Liquid metal (LM) elastomer composites offer promising potential in soft robotics, wearable electronics, and human-machine interfaces. Direct ink write (DIW) 3D printing offers a versatile manufacturing technique capable of precise control over LM microstructures, yet challenges such as interfilament void formation in multilayer structures impact material performance. Here, a DIW strategy is introduced to control both LM microstructure and material architecture. Investigating three key process parameters–nozzle height, extrusion rate, and nondimensionalized nozzle velocity–it is found that nozzle height and velocity predominantly influence filament geometry. The nozzle height primarily dictates the aspect ratio of the filament and the formation of voids. A threshold print height based on filament geometry is identified; below the height, significant surface roughness occurs, and above the ink fractures, which facilitates the creation of porous structures with tunable stiffness and programmable LM microstructure. These porous architectures exhibit reduced density and enhanced thermal conductivity compared to cast samples. When used as a dielectric in a soft capacitive sensor, they display high sensitivity (gauge factor = 9.0), as permittivity increases with compressive strain. These results demonstrate the capability to simultaneously manipulate LM microstructure and geometric architecture in LM elastomer composites through precise control of print parameters, while maintaining geometric fidelity in the printed design.

Spencer Pak↗
NASA NTRS2006

Effects of Laser and Shot Peening on Fatigue Crack Growth in Friction Stir Welds

The effects of laser, and shot peening on the fatigue life of Friction Stir Welds (FSW) have been investigated. The surface roughness resulting from various peening techniques was assessed, and the fracture surfaces microstructure was characterized. Laser peening resulted in an increase in fatigue life approximately 60%, while shot peening resulted in 10% increase when compared to the unpeened material. The surface roughness of shot peening was significantly higher compared to the base material, while specimens processed with laser peening were relatively smooth.

Hatamleh, Omar↗
NASA NTRS1975

A seismic refraction technique used for subsurface investigations at Meteor Crater, Arizona

A seismic refraction technique for interpreting the subsurface shape and velocity distribution of an anomalous surface feature such as an impact crater is described. The method requires the existence of a relatively deep refracting horizon and combines data obtained from both standard shallow refraction spreads and distant offset shots by using the deep refractor as a source of initial arrivals. Results obtained from applying the technique to Meteor crater generally agree with the known structure of the crater deduced by other investigators and provide new data on an extensive fractured zone surrounding the crater. The breccia lens is computed to extend roughly 190 m below the crater floor, about 30 m less than the value deduced from early drilling data. Rocks around the crater are fractured as distant as 900 m from the rim crest and to a depth of at least 800 m beneath the crater floor.

Ackermann, H. D.↗
DOE OSTI2022

Effects of surface treatments on ABS mechanical properties from fused filament fabrication

This paper examines the influence of surface treatments on the mechanical properties of acrylonitrile butadiene styrene (ABS) samples printed by fused filament fabrication (FFF). Prior efforts have applied brushing, painting, solvent dipping, infiltration, and vapor smoothing as post-processing surface treatments to improve the mechanical properties of FFF components. Additionally, because FFF can produce components with undesirable surface roughness, mechanical abrasion, epoxy coating, and acetone treatment may increase tensile strength by decreasing stress concentrations. Ridged surface texture may provide desirable tribological or handling properties. Based on these opportunities, this paper investigates abrasive media blasting, epoxy coating, acetone immersion, and ridged texturing surface treatments on the tensile strength and other mechanical properties of FFF ABS samples. ASTM D638-14 Type-I samples were printed, treated on all sample sides, and tested. From tensile tests, the elastic modulus, tensile strength, and fracture strain for both the untreated and treated ABS samples were calculated. For each sample, the surface finish and fracture macromorphology were observed with optical microscopy and the roughness values for the surface finish were calculated from profilometer data. Furthermore, samples were submerged in water and weighed periodically to measure mass changes due to water absorption. From surface profilometry and optical miscopy data, mechanical media blasting, epoxy coating, and immersion in all concentrations of acetone decreased surface roughness. Overall, on average, grit blasting with large beads and epoxy coating led to 2.6% and 1.2% increases in tensile strength, respectively; immersion in 40% acetone led to a 1.9% increase in tensile strength while treatment in 60% and 80% acetone decreased tensile strength by 4.9% and 1.9%, respectively. The study concludes that only grit blasting with large beads, immersion in 60% acetone, and the ridged texture significantly affected the tensile strength.

36 MATERIALS SCIENCE↗
NASA NTRS1981

An experimental investigation of silicon wafer surface roughness and its effect on the full strength of plated metals

Plated silicon wafers with surface roughness ranging from 0.4 to 130 microinches were subjected to tensile pull strength tests. Electroless Ni/electroless Cu/electroplated Cu and electroless Ni/electroplated Cu were the two types of plate contacts tested. It was found that smoother surfaces had higher pull strength than rougher, chemically etched surfaces. The presence of the electroless Cu layer was found to be important to adhesion. The mode of fracture of the contact as it left the silicon was studied, and it was found that in almost all cases separation was due to fracture of the bulk silicon phase. The correlation between surface roughness and mode of contact failure is presented and interpreted.

Spiers, G. D.↗
NASA NTRS1993

A formational model for the polygonal terrains of Mars: Taking a crack at the genesis of the Martian polygons

The mechanism for the genesis of the polygonal terrains in Acidalia and Utopia Planitia has long been sought: however, no completely satisfying model was put forth that characterizes the evolution of these complexly patterned terrains. The polygons are roughly hexagonal but some are not entirely enclosed by fractures. These polygonal features range in widths from approximately 5 to 20 km. Several origins were proposed that describe the polygon borders as desiccation cracks, columnar jointing in a cooled lava, or frost-wedge features. These tension-induced cracking hypotheses were addressed by Pechmann, who convincingly disputes these mechanisms of formation based on scale magnitude difficulties and morphology. Pechmann suggests instead that the cracks delineating the 5-20-km-wide polygons on the northern plains of Mars are graben resulting from deep-seated, uniform, horizontal tension. The difficulty with this hypothesis is that no analogous polygonal forms are known to have originated by tectonism on Earth. McGill and Hills propose that the polygonal terrains on Mars resulted from either rapid desiccation of sediments or cooling of volcanics coupled with differential compaction of the material over a buried irregular topographic surface. They suggest that fracturing was enhanced over the areas of positive relief and was suppressed above the topographic lows. McGill and Hills suggest that the spacing of the topographic highs primarily controls the size of the Martian polygons and the physics of the shrinkage process is a secondary concern. Ray et. al. conducted a terrestrial study of patterned ground in periglacial areas of the U.S. to determine the process responsible for polygonal ground formation. They developed a model for polygon formation in which convection of seasonal melt water above a permafrost layer, driven by an unstable density stratification, differentially melts the permafrost interface, causing it to become undulatory.

Wenrich, M. L.↗
NASA NTRS2002

The Influence of Interfacial Roughness on Fiber Sliding in Oxide Composites with La-Monazite Interphases

Room temperature debonding and sliding of La-Monazite coated fibers is assessed using a composite with a polycrystalline alumina matrix and fibers of several different single crystal (mullite, sapphire) and directionally solidified eutectic (Al2O3/Y3Al5O12 and Al2O3/Y-ZrO2) compositions. These fibers provide a range of residual stresses and interfacial roughnesses. Sliding occurred over a debond crack at the fiber-coating interface when the sliding displacement and surface roughness were relatively small. At large sliding displacements with relatively rough interfaces, the monazite coatings were deformed extensively by fracture, dislocations and occasional twinning, whereas the fibers were undamaged. Dense, fine-grained (10 nm) microstructures suggestive of dynamic recrystallization were also observed in the coatings. Frictional heating during sliding is assessed. The possibility of low temperature recrystallization is discussed in the light of the known resistance of monazite to radiation damage. The ability of La-Monazite to undergo plastic deformation relatively easily at low temperatures may be enabling for its use as a composite interface.

Davis, J. B.↗
NASA NTRS2008

Compression Strength of Sulfur Concrete Subjected to Extreme Cold

Sulfur concrete cubes were cycled between liquid nitrogen and room temperature to simulate extreme exposure conditions. Subsequent compression testing showed the strength of cycled samples to be roughly five times less than those non-cycled. Fracture surface examination showed de-bonding of the sulfur from the aggregate material in the cycled samples but not in those non-cycled. The large discrepancy found, between the samples is attributed to the relative thermal properties of the materials constituting the concrete.

Grugel, Richard N.↗
DOE OSTI2024

Impacts of irregularly-distributed acidified brine flow on geo-chemo-mechanical alteration in an artificial shale fracture under differential stress

The efficacy of geological carbon sequestration is reliant on the integrity of the caprock and its resistance to physical and chemical alteration. Caprocks with high abundance of reactive carbonates like calcite are susceptible to acid-promoted dissolution and can result in structural weakening. This work investigates the effect of acidified brine flow through an artificially fractured, high-carbonate (30 % by XRD) shale under differential compressive stress. Cylindrical samples were cut in half vertically and milled to create an artificial fracture with interlocking asperities and open channels. Samples were sheared with a single applied stress in a custom flow cell housed within an industrial CT scanner. Further, either acidic (pH 4) or reservoir-simulated (pH 9.5) brine was flowed through the artificial fracture for 7–8 days under reservoir pressure and room temperature. Model simulations indicate flow mainly occurred in open channels, with limited flow between overlapping asperities. Analysis of fracture surfaces by optical and scanning electron microscopy show increased surface alteration and roughness after exposure to pH 4 versus pH 9.5 brine indicating mineral dissolution/loss, and this effect is greater in areas that receive the highest brine flows. Similarly, surface analysis by scratch testing shows fracture toughness decreases more after exposure to acidic versus reservoir-simulated brine, with the greatest alteration in areas of highest acidic brine flows. Despite weakening, no shear slip occurred. Overall, the results indicate that acidified brine can result in significant physical and geomechanical alteration of irregular fracture surfaces in shale caprock, with greatest effects in preferential flow regions.

58 GEOSCIENCES↗
DOE OSTI2025

Micro-structural features and material properties impact on adhesive metal joints via computational modeling and machine learning

The quality of structural bonding in practical applications depends on various factors arising from materials, pre-processing conditions, and manufacturing. Understanding how these factors influence bonding performance and determining their relative importance are of significant interest. Thus, this study evaluates the effects of microstructural features and material properties on the structural strength of adhesively-bonded metal joints at the submillimeter scale, utilizing a combination of Finite Element Modeling (FEM) and Machine Learning (ML) with Gradient Boosting Regression (GBR). The microstructural features include adhesive thickness, internal voids within the adhesive, adherend-adhesive interfacial voids, void size and volume fraction, and surface roughness. The material properties include the constitutive behavior of the adhesive, as well as the adherend-adhesive interfacial strength and fracture energy. The changes in structural strength and morphologies of the bonded metal structures with respect to different microstructural features and material properties were clarified by FEM. By further leveraging ML-GBR, the sequence of importance of these factors affecting bonding performance across various scenarios was summarized. This work provides valuable insights into the development of improved structural bonding for adhesive joints in industries such as automotive , aerospace, and beyond.

36 MATERIALS SCIENCE↗
DOE OSTI2021

SURFACE FINISHING AND ELECTROLESS NICKEL PLATING OF ADDITIVELY MANUFACTURED (AM) METAL COMPONENTS

This study investigates the application of electroless nickel deposition on additively manufactured stainless steel samples. Current additive manufacturing (AM) technologies produce metal components with a rough surface. Rough surfaces generally exhibit fatigue characteristics, increasing the probability of initiating a crack or fracture to the printed part. For this reason, the direct use of as-produced parts in a finished product cannot be actualized, which presents a challenge. Post-processing of the AM parts is therefore required to smoothen the surface. This study analyzes chempolish (CP) and electropolish (EP) surface finishing techniques for post-processing AM stainless steel components CP has a great advantage in creating uniform, smooth surfaces regardless of size or part geometry EP creates an extremely smooth surface, which reduces the surface roughness to the sub-micrometer level. In this study, we also investigate nickel deposition on EP, CP, and as-built AM components using electroless nickel solutions. Electroless nickel plating is a method of alloy treatment designed to increase manufactured component's hardness and surface resistance to the unrelenting environment. The electroless nickel plating process is more straightforward than its counterpart electroplating.. We use low-phosphorus (2-5% P), medium-phosphorus (6-9% P), and high-phosphorus (10-13% P). These Ni deposition experiments were optimized using the L9 Taguchi design of experiments (TDOE), which compromises the prosperous content in the solution, surface finish, plane of the geometry, and bath temperature. The pre-and post-processed surface of the AM parts was characterized by KEYENCE Digital MicroscopeVHX-7000 and Phenom XL Desktop SEM. The experimental results show that electroless nickel deposition produces uniform Ni coating on the additively manufactured components up to 20 μm per hour. Mechanical properties of as-built and Ni coated AM samples were analyzed by applying a standard 10 N scratch test. Nickel coated AM samples were up to two times scratch resistant compared to the as-built samples. This study suggests electroless nickel plating is a robust viable option for surface hardening and finishing AM components for various applications and operating conditions.

Keywords: additive manufacturing, fatigue, chempol↗
DOE OSTI2020

The emergence of small-scale self-affine surface roughness from deformation

Most natural and man-made surfaces appear to be rough on many length scales. There is presently no unifying theory of the origin of roughness or the self-affine nature of surface topography. One likely contributor to the formation of roughness is deformation, which underlies many processes that shape surfaces such as machining, fracture, and wear. Using molecular dynamics, we simulate the biaxial compression of single-crystal Au, the high-entropy alloy Ni 36.67 Co 30 Fe 16.67 Ti 16.67 , and amorphous Cu 50 Zr 50 and show that even surfaces of homogeneous materials develop a self-affine structure. By characterizing subsurface deformation, we connect the self-affinity of the surface to the spatial correlation of deformation events occurring within the bulk and present scaling relations for the evolution of roughness with strain. These results open routes toward interpreting and engineering roughness profiles.

42 ENGINEERING↗
DOE OSTI2023

Experimental flow-through a single fracture with monolayer proppant at reservoir conditions: A case study on Caney Shale, Southwest Oklahoma, USA

Global energy systems are undergoing a crucial transition to clean energy sources, thereby moving away from fossil-fuel based energy with the ultimate aim of reducing carbon dioxide emissions. It is essential to continue to advance in exploring and developing shale gas resources as this will underpin the global supply of natural gas that is needed to support the energy transition. The challenge hereby is that the slow fluid flow of the shale matrix due to its very low permeability requires large-scale volume fracturing to produce a conductive fracture network that enhances the connectivity between the shale formation and the wellbore. This work examines the influence of a thin proppant layer on a single fracture using a flow-through experiment, and also explores whether proppant embedment in the Caney shale is affected by the rock mineralogy, surface roughness, fluids, confining stress, time, temperature and bedding. The experiment was conducted for a duration of nine days (216 h), experimental temperature was varied from ambient temperature to reservoir temperature of 125 °C (257 °F) and confining stress was varied from 367 psi (2.53MPa) to a maximum of 4011.82 psi (27.66 MPa). Here, we find that the conductivity of the fracture is primarily influenced by the layer of proppant used, surface roughness, mineralogy, fluids, temperature and closure stress.

Caney shale↗
DOE OSTI2023

Performance characterization of freeform finished surfaces of potassium dihydrogen phosphate using fluid jet polishing with a nonaqueous slurry

Abstract Potassium dihydrogen phosphate (KDP) and its deuterated analog (DKDP) are unique nonlinear optical materials for high power laser systems. They are used widely for frequency conversion and polarization control by virtue of the ability to grow optical-quality crystals at apertures suitable for fusion-class laser systems. Existing methods for freeform figuring of KDP/DKDP optics do not produce surfaces with sufficient laser-induced–damage thresholds (LIDT’s) for operation in the ultraviolet portion of high-peak-power laser systems. In this work, we investigate fluid jet polishing (FJP) using a nonaqueous slurry as a sub-aperture finishing method for producing freeform KDP surfaces. This method was used to selectively polish surface areas to different depths on the same substrate with removals ranging from 0.16 μm to 5.13 μm. The finished surfaces demonstrated a slight increase in roughness as the removal depth increased along with a small number of fracture pits. Laser damage testing with 351 nm, 1 ns pulses demonstrated excellent surface damage thresholds, with the highest values in areas devoid of fracture pits. This work demonstrates, for the first time, a method that enables fabrication of a waveplate that provides tailored polarization randomization that can be scaled to meter-sized optics. Furthermore, this method is based on FJP technology that incorporates a nonaqueous slurry specially designed for use with KDP. This novel nonaqueous FJP process can be also used for figuring other types of materials that exhibit similar challenging inherent properties such as softness, brittleness, water-solubility, and temperature sensitivity.

36 MATERIALS SCIENCE↗
NASA NTRS1979

A special class of planetary collisions - Theory and evidence

Collisions between comparable-sized planetary bodies are a special class of collisions, rarer than other collisions, but producing interesting products, such as unfractured dumbbell-shaped contact binaries, partly brecciated elongated bodies, totally brecciated spheroidal bodies, and perhaps co-orbiting binary pairs or swarms. Qualitative and rough quantitative theories are presented to indicate collision outcomes. Contact binaries or fractured elongated bodies as large as tens or hundreds of kilometers across can be produced - larger than hitherto considered. Lengths about 20 to 200 km are most probable for igneous or ordinary chondritic elongated objects formed by collision, but other lengths could result from tidal evolution of pairs. Though most elongated asteroids are probably collision fragments, as usually assumed, some may instead be accretionary products. Trojan asteroid 624 Hektor is a candidate. Some polymict, genomict, and monomict brecciated meteorites may be better explained by large-scale fragmentation and immediate gravitational re-assembly of parent bodies than by local-scale processes of cratering on parent-body surfaces.

Hartmann, W. K.↗
DOE OSTI2020

Build orientation, surface roughness, and scan path influence on the microstructure, mechanical properties, and flexural fatigue behavior of Ti–6Al–4V fabricated by electron beam melting

In the present work, microstructure and fatigue behavior of Electron Beam Melted (EBM) Ti–6Al–4V have been systematically studied. Fatigue behavior was investigated using four-point bend tests of rectangular bars with internal features fabricated with different build orientations, scan paths, and surface conditions. Microstructural variations were evaluated by optical microscopy and Vickers micro-hardness indentations, both of which were found to be consistent throughout the build and within ranges reported in the literature. The fatigue performance of the EBM material was comparable to wrought Ti–6Al–4V when the loading direction was parallel to the build direction, but severely limited when loaded perpendicular to the build direction or if surface roughness defects were present. Scanning electron microscopy and interrupted fatigue tests were utilized to characterize fracture surfaces, failure mechanisms, crack initiation, and propagation behavior. Crack initiation sites in the vertically-oriented specimens were identified to be melt-related defects formed by insufficient melting.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Early impact basins and the onset of plate tectonics

The fundamental crustal dichotomy of the Earth (high and low density crust) was established nearly 4 billion years ago. Therefore, subductable crust was concentrated at the surface of the Earth very early in its history, making possible an early onset for plate tectonics. Simple thermal history calculations spanning 1 billion years show that the basin forming impact thins the lithosphere by at least 25%, and increases the sublithosphere thermal gradients by roughly 20%. The corresponding increase in convective heat transport, combined with the highly fractured nature of the thinned basin lithosphere, suggest that lithospheric breakup or rifting occurred shortly after the formation of the basins. Conditions appropriate for early rifting persisted from some 100,000,000 years following impact. We suggest a very early stage of high temperature, fast spreading "microplate" tectonics, originating before 3.5 billion years ago, and gradually stabilizing over the Archaean into more modern large plate or Wilson Cycle tectonics.

Frey, H.↗