Search NASA⌕ Search

SEARCH · Search NASA

Results for “soil aggregation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Evolution of carbon isotopes, agglutinates, and the lunar regolith

Apollo 17 light-mantle soils and Apollo 15 Apennine Front soils are compared with respect to isotopic enrichment of C-13 and the maturity of the site. Analyses of soil-size fractions indicate that while the carbon concentration on particle surfaces remains relatively constant with increasing soil maturity, total surface-correlated carbon increases due to increasing total soil surface area. The role of agglutinates in the incorporation of surface-correlated carbon into aggregate grains is examined; agglutinates contain a major percentage of the carbon found in mature soil, and the volume-correlated carbon component in agglutinates apparently continues to increase after the surface-correlated carbon concentrations have reached a constant value. Constraints that may limit the carbon concentration in lunar soils to a value not greater than 300 micrograms/g are considered.

Desmarais, D. J.↗

Effects of soil tillage on the microwave emission of soils

In order to understand the interactions of soil properties and microwave emission better, a series of field experiments were conducted in 1984. Small plots were measured with a truck-mounted passive microwave radiometer operating at 1.4 GHz. These data were collected concurrent with ground observations of soil moisture and bulk density. Treatment effects studied included different soil moisture contents and bulk densities. Evaluations of the data have shown that commonly used models of the dielectric properties of wet soils do not explain the observations obtained in these experiments. This conclusion was based on the fact that the roughness parameters determined through optimization were significantly larger than those observed in similar investigations. These discrepancies are most likely due to the soil structure. Commonly used models assume a homogeneous three phase mixture of soil solids, air and water. Under tilled conditions the soil is actually a two phase mixture of aggregates and voids. Appropriate dielectric models for this tilled condition were evaluated and found to explain the observations. These results indicate that previous conclusions concerning the effects of surface roughness in tilled fields may be incorrect, and they may explain some of the inconsistencies encountered in roughness modeling.

Jackson, T. J.↗

Mechanical Properties and Durability of "Waterless Concrete"

Waterless concrete consists of molten elementary sulfur and aggregate. The aggregates in lunar environment will be lunar rocks and soil. Sulfur is present on the Moon in Troilite soil (FeS) and by oxidation soil iron and sulfur can be produced. Iron can be used to reinforce the sulfur concrete. Sulfur concrete specimens were cycled between liquid nitrogen (approximately 191 C) and room temperature (approximately 21 C) to simulate exposure to a lunar environment. Cycled and control specimens were subsequently tested in compression at room temperatures (approximately 21 C) and approximately 101 C. Test results showed that due to temperature cycling, compressive strength of cycled specimens was 20% of those non-cycled. Microscopic examination of the fracture surfaces from the cycled samples showed clear de-bonding of the sulfur from the aggregate material whereas it was seen well bonded in those non-cycled. This reduction in strength can be attributed to the large differences in thermal coefficients of expansion of the materials constituting the concrete which promoted cracking. Similar sulfur concrete mixtures were strengthened with short and long glass fibers. The glass fibers from lunar regolith simulant was melted in a 25 cc Pt-Rh crucible in a Sybron Thermoline high temperature MoSi2 furnace at melting temperatures of 1450 to 1600 C for times of 30 min to 1 hour. Glass fibers were cast from the melt into graphite crucibles and were annealed for a couple of hours at 600 C. Glass fibers and small rods were pulled from the melt. The glass melt wets the ceramic rod and long continuous glass fibers were easily hand drawn. The glass fibers were immediately coated with a protective polymer to maintain the mechanical strength. The glass fibers were used to reinforce sulfur concrete plated to improve the flexural strength of the sulfur concrete. Prisms beams strengthened with glass fibers were tested in 4-point bending test. Beams strengthened with glass fiber showed to exhibit an increase in the flexura strength by as much as 45%.

Toutanji, Houssam↗

Formation of Nanophase Iron in Lunar Soil Simulant for Use in ISRU Studies

For the prospective return of humans to the Moon and the extensive amount of premonitory studies necessary, large quantities of lunar soil simulants are required, for a myriad of purposes from construction/engineering purposes all the way to medical testing of its effects from ingestion by humans. And there is only a limited and precious quantity of lunar soil available on Earth (i.e., Apollo soils) - therefore, the immediate need for lunar soil simulants. Since the Apollo era, there have been several simulants; of these JSC-1 (Johnson Space Center) and MLS-1 (Minnesota Lunar Simulant) have been the most widely used. JSC-1 was produced from glassy volcanic tuff in order to approximate lunar soil geotechnical properties; whereas, MLS-1 approximates the chemistry of Apollo 11 high-Ti soil, 10084. Stocks of both simulants are depleted, but JSC-1 has recently gone back into production. The lunar soil simulant workshop, held at Marshall Space Flight Center in January 2005, identified the need to make new simulants for the special properties of lunar soil, such as nanophase iron (np-Fe(sup 0). Hill et al. (2005, this volume) showed the important role of microscale Fe(sup 0) in microwave processing of the lunar soil simulants JSC-1 and MLS-1. Lunar soil is formed by space weathering of lunar rocks (e.g., micrometeorite impact, cosmic particle bombardment). Glass generated during micrometeorite impact cements rock and mineral fragments together to form aggregates called agglutinates, and also produces vapor that is deposited and coats soil grains. Taylor et al. (2001) showed that the relative amount of impact glass in lunar soil increases with decreasing grain size and is the most abundant component in lunar dust (less than 20 micrometer fraction). Notably, the magnetic susceptibility of lunar soil also increases with the decreasing grain size, as a function of the amount of nanophase-sized Fe(sup 0) in impact-melt generated glass. Keller et al. (1997, 1999) also discovered the presence of abundant np-Fe(sup 0) particles in the glass patinas coating most soil particles. Therefore, the correlation of glass content and magnetic susceptibility can be explained by the presence of the np-Feo particles in glass: small particles contain relatively more np-Fe(sup 0) as glass coatings because the surface area versus mass ratio of the grain size is so increased. The magnetic properties of lunar soil are important in dust mitigation on the Moon (Taylor et al. 2005). Thus material simulating this property is important for testing mitigation methods using electromagnetic field. This np- Fe(sup 0) also produces a unique energy coupling to normal microwaves, such as present in kitchen microwave ovens. Effectively, a portion of lunar soil placed in a normal 2.45 GHz oven will melt at greater than 1200 C before your tea will boil at 100 C, a startling and new discovery reported by Taylor and Meek (2004, 2005). Several methods have been investigated in attempts to make nanophase-sized Feo dispersed within silicate glass; like in the lunar glass. We have been successful in synthesizing such a product and continue to improve on our recipe. We have performed extensive experimentation on this subject to date. Ultimately it will probably be necessary to add this np-Fe(sup 0) bearing silicate glass to lunar soil stimulant, like JSC-1, to actually produce the desired magnetic and microwave coupling properties for use in appropriate ISRU experimentation.

Liu, Yang↗

Comparison of high-resolution airborne soil moisture retrievals to SMAP soil moisture during the SMAP validation experiment 2016 (SMAPVEX16)

The NASA's Soil Moisture Active Passive (SMAP) mission conducted a field experiment with its partners over two 40-km agricultural domains in Iowa and Manitoba in the summer of 2016 to address concerns observed in SMAP soil moisture (SM) retrievals over agricultural areas. The experiment featured airborne Passive Active L-band System (PALS) flights over each domain with intensive ground measurements and dense networks of SM monitoring stations. With two intensive observation periods separated in time (May 28–June 20 and July 14–August 16), the flights captured both early-season/low vegetation and later-season/high-vegetation conditions. The comparison of the PALS brightness temperature (TB) measurements to the SMAP TB observed over the sites resulted in root mean square difference (RMSD) of 2.8 K and 4.0 K for vertical and horizontal polarizations, respectively. The subsequent SM analysis rescaled the PALS TB with the SMAP TB to allow equitable comparisons between the SM retrievals from the two instruments. The PALS SM retrieval algorithm used the SM sampled by the ground teams during the overpass days for tuning, and was parameterized by a high-resolution vegetation water content product calibrated using vegetation samples collected during the experiment. The tuning process was not able to find a satisfactory result with a temporally constant set of parameters in the single channel algorithm for the two intensive observation periods of the experiment. This result indicated that the rapid change in the vegetation structure during the growth stages and likely variation in the surface roughness conditions were not compatible with rigid parameterization over the entire period. However, using seasonally variable parameters we found that it was possible to retrieve soil moisture with satisfactory accuracy. Comparative analysis with the SMAP SM product included aggregation of the PALS SM to the SMAP pixel-scale. The RMSD between the PALS SM and the aggregated manual field samples was <0.04 m3/m3 with Pearson correlation >0.85 for both sites. The comparison between different in situ sources indicated that the soil moisture network measurements were not the source of the large biases observed for SMAP over the sites reported in earlier studies. Therefore, the results suggested the rapidly growing vegetation and the early-season surface condition changes not captured by the SMAP algorithm caused the SMAP retrieval errors. In addition, the significant deviations of the vegetation water content used by the SMAP product from the calibrated vegetation water content obtained during the experiment compounds the problem.

Andreas Colliander↗

A Conceptual Approach to Assimilating Remote Sensing Data to Improve Soil Moisture Profile Estimates in a Surface Flux/Hydrology Model: Overview - Part 1

Knowledge of the amount of water in the soil is of great importance to many earth science disciplines. Soil moisture is a key variable in controlling the exchange of water and energy between the land surface and the atmosphere. Thus, soil moisture information is valuable in a wide range of applications including weather and climate, runoff potential and flood control, early warning of droughts, irrigation, crop yield forecasting, soil erosion, reservoir management, geotechnical engineering, and water quality. Despite the importance of soil moisture information, widespread and continuous measurements of soil moisture are not possible today. Although many earth surface conditions can be measured from satellites, we still cannot adequately measure soil moisture from space. Research in soil moisture remote sensing began in the mid 1970s shortly after the surge in satellite development. Recent advances in remote sensing have shown that soil moisture can be measured, at least qualitatively, by several methods. Quantitative measurements of moisture in the soil surface layer have been most successful using both passive and active microwave remote sensing, although complications arise from surface roughness and vegetation type and density. Early attempts to measure soil moisture from space-borne microwave instruments were hindered by what is now considered sub-optimal wavelengths (shorter than 5 cm) and the coarse spatial resolution of the measurements. L-band frequencies between 1 and 3 GHz (10-30 cm) have been deemed optimal for detection of soil moisture in the upper few centimeters of soil. The Electronically Steered Thinned Array Radiometer (ESTAR), an aircraft-based instrument operating a 1,4 GHz, has shown great promise for soil moisture determination. Initiatives are underway to develop a similar instrument for space. Existing space-borne synthetic aperture radars (SARS) operating at C- and L-band have also shown some potential to detect surface wetness. The advantage of radar is its much higher resolution than passive microwave systems, but it is currently hampered by surface roughness effects and the lack of a good algorithm based on a single frequency and single polarization. In addition, its repeat frequency is generally low (about 40 days). In the meantime, two new radiometers offer some hope for remote sensing of soil moisture from space. The Tropical Rainfall Measuring Mission (TRMM) Microwave Imager (TMI), launched in November 1997, possesses a 10.65 GHz channel and the Advanced Microwave Scanning Radiometer (AMSR) on both the ADEOS-11 and Earth Observing System AM-1 platforms to be launched in 1999 possesses a 6.9 GHz channel. Aside from issues about interference from vegetation, the coarse resolution of these data will provide considerable challenges pertaining to their application. The resolution of TMI is about 45 km and that of AMSR is about 70 km. These resolutions are grossly inconsistent with the scale of soil moisture processes and the spatial variability of factors that control soil moisture. Scale disparities such as these are forcing us to rethink how we assimilate data of various scales in hydrologic models. Of particular interest is how to assimilate soil moisture data by reconciling the scale disparity between what we can expect from present and future remote sensing measurements of soil moisture and modeling soil moisture processes. It is because of this disparity between the resolution of space-based sensors and the scale of data needed for capturing the spatial variability of soil moisture and related properties that remote sensing of soil moisture has not met with more widespread success. Within a single footprint of current sensors at the wavelengths optimal for this application, in most cases there is enormous heterogeneity in soil moisture created by differences in landcover, soils and topography, as well as variability in antecedent precipitation. It is difficult to interpret the meaning of 'mean' soil moisture under such conditions and even more difficult to apply such a value. Because of the non-linear relationships between near-surface soil moisture and other variables of interest, such as surface energy fluxes and runoff, mean soil moisture has little applicability at such large scales. It is for these reasons that the use of remote sensing in conjunction with a hydrologic model appears to be of benefit in capturing the complete spatial and temporal structure of soil moisture. This paper is Part I of a four-part series describing a method for intermittently assimilating remotely-sensed soil moisture information to improve performance of a distributed land surface hydrology model. The method, summarized in section II, involves the following components, each of which is detailed in the indicated section of the paper or subsequent papers in this series: Forward radiative transfer model methods (section II and Part IV); Use of a Kalman filter to assimilate remotely-sensed soil moisture estimates with the model profile (section II and Part IV); Application of a soil hydrology model to capture the continuous evolution of the soil moisture profile within and below the root zone (section III); Statistical aggregation techniques (section IV and Part II); Disaggregation techniques using a neural network approach (section IV and Part III); and Maximum likelihood and Bayesian algorithms for inversely solving for the soil moisture profile in the upper few cm (Part IV).

Crosson, William L.↗

Metal silicate relationships in Apollo 17 soils

A petrographic, metallographic, and electron probe study of particles from two Apollo 17 soils is reported. A mixing model for the formation of the Apollo 17 soils is proposed. It is found that equilibration temperatures for two-phase metal aggregates range from 375 to 475 C for metal-phosphide particles and from 480 to 630 C for alpha-gamma particles, and that the anorthositic soil particles contain metal of meteoritic Ni-Co content. The Camelot Crater and the Sculptured Hills soil compositions are discussed.

Goldstein, J. I.↗

Optical effects of space weathering: The role of the finest fraction

The optical properties of lunar soils are different than those of rocks which they are derived. As a consequence of lunar space weathering, soils are darker and exhibit a distinctive red-sloped continuum and weaker mineral absorption bands. The accumulation of dark glass-welded aggregates (agglutinates) has been thought to account for these optical effects of space weathering on lunar soils. Spectroscopic analyses of agglutinate separates and size fractions for a suite of lunar soils presented here indicate that the agglutinate paradigm is insufficient to fully account for lunar optical alteration. It is the finest fraction of lunar soils (less than 25 microns which constitute approximately 25% wt.) that dominates the optical properties of the bulk soil. Unlike size fractions of most silicates for which the finest fraction is the brightest, the lunar soil size fractions all have comparable albedos in the short-wavelength visible. In the near infrared, however, it is the finest fraction that exhibits the steep red continuum and weak absorption bands. The properties of the finest fraction cannot be duplicated by preparing a fine fraction by grinding larger agglutinate-rich soil particles. These results suggest space weathering on airless bodies is dominated by surface correlated processes (perhaps associated with the developement of fine-grained Fe(dot) on or near the surface of grains), and the accumulation of the large agglutinates is not necessarily required to account for lunar optical alteration.

Pieters, C. M.↗

Performance of "Waterless Concrete"

Waterless concrete consists of molten elementary sulfur and aggregate. The aggregates in a lunar environment will be lunar rocks and soil. Sulfur is present on the Moon in Troilite soil (FeS) and, by oxidation of the soil, iron and sulfur can be produced. Sulfur concrete specimens were cycled between liquid nitrogen (approx.]91 C) and room temperature (^21 C) to simulate exposure to a lunar environment. Cycled and control specimens were subsequently tested in compression at room temperatures (^21 C) and ^-101 C. Test results showed that due to temperature cycling, the compressive strength of cycled specimens was 20% of those non-cycled. This reduction in strength can be attributed to the large differences in thermal coefficients of expansion of the materials constituting the concrete which promoted cracking. Similar sulfur concrete mixtures were strengthened with short and long glass fibres. The lunar regolith simulant was melted in a 25 cc Pt- Rh crucible in a Sybron Thermoline high temperature MoSi2 furnace at melting temperatures of 1450 to 1600 C for times of 30 min to i hour. Glass fibres and small rods were pulled from the melt. The glass fibres were used to reinforce sulfur concrete plated to improve the flexural strength of the sulfur concrete. Beams strengthened with glass fibres showed to exhibit an increase in the flexural strength by as much as 45%.

Toutanji, H. A.↗

Particle dynamics of nanoplastics suspended in water with soil microparticles: insights from small angle neutron scattering (SANS) and ultra-SANS

Small-angle neutron scattering (SANS) and ultra-SANS (USANS) were employed to understand the aggregation behavior and observe the size reduction for nanoplastics (NPs) formed from a biodegradable mulch film, and microparticles of vermiculite (V), an artificial soil, suspended in water in the presence of low convective shear (ex situ stirring) prior to measurements. Neutron contrast matching was employed to minimize the signal of V (by 100-fold) and thereby isolate the signal due to NPs in the neutron beam, as the contrast match point (CMP) for V (67 vol% deuteration of water) differed from that of NPs by more than 20%. The original NPs' size distribution was bimodal: <200 nm and 500–1200 nm, referred to as small and large NPs, i.e., SNPs and LNPs, respectively. In the absence of V, SNPs formed homoaggregates at higher concentrations that decreased with stirring time, while the size of LNPs remained unchanged. The presence of V at 2-fold lower concentration than NPs did not change the size of SNPs but reduced the size of LNPs by nearly 2-fold as stirring time increased. Because the size of SNPs and LNPs did not differ substantially between CMP and 100% D 2 O solvents, it is evident that SNPs and LNPs are mainly composed of NPs and not V. In conclusion, the results suggest that LNPs are susceptible to size reduction through collisions with soil microparticles via convection, yielding SNPs near soil–water interfaces within vadose zones.

Nanoplastics↗

Divide and conquer: using RhizoVision Explorer to aggregate data from multiple root scans using image concatenation and statistical methods

Roots are important in agricultural and natural systems for determining plant productivity and soil carbon inputs. Sometimes, the amount of roots in a sample is too much to fit into a single scanned image, so the sample is divided among several scans, and there is no standard method to aggregate the data. Here, we describe and validate two methods for standardizing measurements across multiple scans: image concatenation and statistical aggregation. We developed a Python script that identifies which images belong to the same sample and returns a single, larger concatenated image. These concatenated images and the original images were processed with RhizoVision Explorer, a free and open-source software. An R script was developed, which identifies rows of data belonging to the same sample and applies correct statistical methods to return a single data row for each sample. These two methods were compared using example images from switchgrass, poplar, and various tree and ericaceous shrub species from a northern peatland and the Arctic. Most root measurements were nearly identical between the two methods except median diameter, which cannot be accurately computed by statistical aggregation. We believe the availability of these methods will be useful to the root biology community.

59 BASIC BIOLOGICAL SCIENCES↗

The MSP 2001 Mars Environmental Compatibility Assessment (MECA)

The Mars Environmental Compatibility Assessment (MECA) will evaluate the Martian environment for soil and dust-related hazards to human exploration as part of the Mars Surveyor Program 2001 Lander. Sponsored by the Human Exploration and Development of Space (HEDS) enterprise, MECA's goal is to evaluate potential geochemical and environmental hazards that may confront future Martian explorers, and to guide HEDS scientists in the development of high fidelity Mars soil simulants. The integrated MECA payload contains a wet-chemistry laboratory, a microscopy station, an electrometer to characterize the electrostatics of the soil and its environment, and arrays of material patches to study the abrasive and adhesive properties of soil grains. The instrument will acquire soil samples with a robotic arm equipped with a camera. MECA will examine surface and subsurface soil and dust in order to characterize particle size, shape, hardness, and also physical characteristics that may provide clues to mineralogy. MECA will characterize soil/water mixtures with respect to pH, redox potential, total dissolved ions, and trace toxins. MECA will determine the nature of electrostatic charging associated with excavation of soil, and the influence of ionizing radiation on material properties. It will also observe natural dust accumulation on engineering materials. To accomplish these objectives, MECA is allocated a mass of 10 kg within an enclosure of 35 x 25 x 15 cm. The Wet Chemistry Laboratory (WCL) consists of four identical cells that will accept samples from surface and subsurface regions accessible to the Lander's robotic arm, mix them with water, and perform extensive analysis of the solution. Ion-selective electrodes and related sensors will evaluate total dissolved solids, redox potential, pH, and the concentration of many soluble ions and gases in wet Martian soil. These electrodes can detect potentially dangerous heavy-metal ions, emitted pathogenic gases, and the soil's corrosive potential. Experiments will include cyclic voltammetry and anodic stripping voltammetry. Complementary to the Viking experiments, the chemical laboratory will characterize the water-soil solution rather than emitted gases. Nonetheless, through analysis of dissolved gases it will be able to replicate many of the Viking observations related to oxidants. MECA's microscopy station combines optical and atomic-force microscopy (AFM) in an actively focused, controlled illumination environment to image particles from millimeters to nanometers in size. Careful selection of substrates allows controlled experiments in adhesion, abrasion, hardness, aggregation, magnetic and other properties. Special tools allow primitive manipulation (brushing and scraping) of samples. Soil particle properties including size, shape, color, hardness, adhesive potential (electrostatic and magnetic), will be determined using an array of sample receptacles and collection substrates. The simple, rugged atomic-force microscope will image in the submicron size range and has the capability of performing a particle-by-particle analysis of the dust and soil. On Earth, the earliest forms of life are preserved as microfossils. The atomic-force microscope will have the required resolution to image down to the scale of terrestrial microfossils and beyond. Mounted on the end of the robot arm, MECA's electrometer actually consists of four types of sensors: an electric field meter, several triboelectricity monitors, an ion gauge, and a thermometer. Tempered only by ultraviolet-light-induced ions and a low-voltage breakdown threshold, the dry, cold, dusty martian environment presents an imposing electrostatic hazard to both robots and humans. The field meter will measure the ambient field on nearby objects while the triboelectric sensors, using identical circuitry, will measure the charge accumulated on test substances as they are dragged through the soil by the arm. The ion chamber, open to the environment, will sense both charged dust and free ions in the air. Over and above the potential threat to electronics, the electrostatic environment holds one of the keys to transport of dust and, consequently, Martian meteorology. Viewed with the robot arm camera, the abrasion and adhesion plates are strategically placed to allow direct observation of the interaction between materials and soils on a macroscopic scale. Materials of graded hardness are placed directly under the robot arm scoop to sense wear and soil hardness. A second array, placed on the lander deck, is deployed after the dust plume of landing has settled. It can be manipulated in a primitive fashion by the arm, first having dirt deposited on it from the scoop and subsequently shaken clean. A third array will passively collect dust from the atmosphere. In addition to objectives related to human exploration, the MECA data set will be rich in information relevant to basic geology, paleoclimate, and exobiology issues. To understand both contemporaneous and ancient processes on Mars, the mineralogy, petrology, and reactivity of Martian surface materials should be constrained. The MECA experiment will shed light on these quantities through its combination of chemistry and microscopy. MECA will be capable of measuring the composition of ancient surface water environments, observing microscopic evidence of geological (and biological?) processes, inferring soil and dust transport, comminution and weathering mechanisms, and characterizing soil horizons that might be encountered during excavation.

Hecht, M. H.↗

Optical effects of space weathering on lunar soils and the role of the finest fraction

Lunar soils represent a cumulative product of space weathering and as such they exhibit distinct optical alteration. In comparison to the optical properties of similar rock powders, lunar soils are darker, have weaker diagnostic absorption bands, and exhibit a characteristic red continuum slope between 0.3 and 4.5 microns. Well-developed (mature) lunar soils have a mean grain size of about 60 microns and may contain more than 50 percent agglutinates (complex, glass-welded aggregates) which were previously believed to be the principal carriers of optical alteration resulting from space weathering. A detailed analysis of the spectral reflectance properties of the bulk soil, size separates, and agglutinate separates of several Apollo and Luna soils has been undertaken to evaluate the validity of the agglutinate paradigm for optical effects of space weathering. The data and results are summarized here which indicate that the finest fraction of natural lunar soils, rather than larger complex agglutinates, carries the principal effects of optical alteration. Bidirectional reflectance spectra were obtained using the small sample configuration of the RELAB facility, which accommodates 5-30 mg of material. Spectra are displayed with the labels for individual samples listed in order of brightness.

Pieters, C. M.↗

Soil Analysis Micro-Mission Concepts Derived from the MSP 2001 Mars Environmental Compatibility Assessment (MECA)

The Mars Environmental Compatibility Assessment (MECA) will evaluate the Martian environment for soil and dust-related hazards to human exploration as part of the Mars Surveyor Program 2001 Lander. The integrated MECA payload contains a wet-chemistry laboratory, a microscopy station, an electrometer to characterize the electrostatic environment, and arrays of material patches to study abrasion and adhesion. Heritage will be all-important for low cost micro-missions, and adaptations of instruments developed for the Pathfinder, '98 and '01 Landers should be strong contenders for '03 flights. This talk has three objectives: (1) Familiarize the audience with MECA instrument capabilities; (2) present concepts for stand-alone and/or mobile versions of MECA instruments; and (3) broaden the context of the MECA instruments from human exploration to a comprehensive scientific survey of Mars. Due to time limitations, emphasis will be on the chemistry and microscopy experiments. Ion-selective electrodes and related sensors in MECA's wet-chemistry laboratory will evaluate total dissolved solids, redox potential, pH, and the concentration of many soluble ions and gases in wet Martian soil. These electrodes can detect potentially dangerous heavy-metal ions, emitted pathogenic gases, and the soil's corrosive potential, and experiments will include cyclic voltammetry and anodic stripping. For experiments beyond 2001, enhancements could allow multiple use of the cells (for mobile experiments) and reagent addition (for quantitative mineralogical and exobiological analysis). MECA's microscopy station combines optical and atomic-force microscopy (AFM) in an actively focused, controlled illumination environment to image particles from millimeters to nanometers in size. Careful selection of substrates allows controlled experiments in adhesion, abrasion, hardness, aggregation, magnetic and other properties. Special tools allow primitive manipulation (brushing and scraping) of samples. Soil particle properties including size, shape, color, hardness, adhesive potential (electrostatic and magnetic), will be determined using an array of sample receptacles and collection substrates. The simple, rugged atomic-force microscope will image in the submicron size range and has the capability of performing a particle-by-particle analysis of the dust and soil. Future implementations might enhance the optical microscopy with spectroscopy, or incorporate advanced AFM techniques for thermogravimetric and chemical analysis.

Hecht, M. H.↗

Spatially explicit terrestrial carbon densities for calibrating the carbon cycle in human-Earth system Models

Soil and vegetation carbon stocks play a critical role in human-Earth system models. These stocks (denominated as densities in MgC/ha) affect variables such as land use change emissions and also influence land use change pathways under climate forcing scenarios where terrestrial carbon is assigned a carbon price. Here we present reharmonized soil and vegetation carbon densities both at the 5-arcmin resolution grid cell level and also aggregated to 235 water sheds for 4 land use types (Cropland, Grazed land, Urban land and unmanaged vegetation) and 15 unmanaged land cover types. Moreover, we use the distribution of carbon within and across pixels to define statistical "states" of carbon, once again differentiated by land type. These statistical states are used to define a range of possible carbon values that can be used for defining initial conditions of soil and vegetation carbon in human-Earth system models. We implement these data in a state-of-the-art multi sector dynamics model, namely the Global Change Analysis Model (GCAM), and show that these new data improve several land use responses, especially when terrestrial carbon is assigned a carbon price.

54 ENVIRONMENTAL SCIENCES↗

Modeling the surface and interior structure of comet nuclei using a multidisciplinary approach

The goal was to investigate the structural properties of the surface of comet nucleus and how the surface should change with time under effect of solar radiation. The basic model that was adopted was that the nucleus is an aggregate of frosty particles loosely bound together, so that it is essentially a soil. The nucleus must mostly be composed of dust particles. The observed mass ratios of dust to gas in the coma is never much greater than unity, but this ratio is probably a much lower limit than that of the nucleus because it is vastly easier to remove the gaseous component by sublimation than by carrying off the dust. Therefore the described models assumed that the particles in the soil were frost covered grains of submicron basic size, closely resembling the interstellar grains. The surface properties of such a nucleus under the effects of heating and cooling as the nucleus approaches and recedes from the Sun generally characterized.

Odell, C. R.↗

Improved Estimates of Pentad Precipitation through the Merging of Independent Precipitation Datasets

Three independent, quasi-global, gridded datasets of precipitation (a rain gauge-based dataset, the satellite-only component of the NASA Integrated Multi-satellitE Retrievals for Global Precipitation Measurement mission [IMERG] Final Run precipitation product, and precipitation estimates derived from NASA Soil Moisture Active Passive [SMAP] soil moisture retrievals), are objectively combined into a single pentad precipitation dataset at 36-km resolution using a unique approach based on extended triple collocation. The quality of each of the four datasets is then evaluated against independent observations. When a global land surface model at 36-km resolution is integrated four times, once utilizing the merged precipitation forcing and once with each of the three contributing datasets, the near-surface soil moisture variations produced with the merged forcing validate best against independent satellite-based soil moisture fields. In addition, the merged dataset is found to be more consistent, relative to each contributor, with estimates of air temperature variations across the globe. The merged dataset thus appears to draw successfully on the complementary strengths of each contributor: the particularly high quality of the rain gauge-based dataset in areas of high gauge density, the more uniform accuracy across the globe of the IMERG data, and the moderate accuracy, particularly in semi-arid regions, of the soil moisture retrieval-based data. Plain Language Summary Obtaining measurements of precipitation across the globe can be challenging. Rain gauges in some ways provide the most accurate measurements, but gauges are absent in many parts of the world, and even where they exist, they only measure precipitation at the gauge itself and therefore may not provide an accurate large-scale average. Satellite-based estimates of precipitation largely overcome these problems, but such data have their own issues, notably a “snapshot” (rather than a time-average) character of the measurements and difficulty associated with interpreting the measured radiances in the presence of complex land surfaces. In the present paper, we use a novel approach to generate a “merged” dataset, one that optimally combines the gauge precipitation information and the satellite-based precipitation information with a third set of estimates derived from soil moisture retrievals. The merged precipitation dataset and each of the three contributors (aggregated here to 5-day averages at a spatial resolution of about 36-km) are then evaluated for consistency with independent geophysical fields. The merged dataset is found to perform best, a clear indication that it takes proper advantage of the complementary strengths of each contributor and, accordingly, that the presented approach for merging the different contributors is indeed viable.

Precipitation↗

Unraveling the depth-dependent causal dynamics of methanogenesis and methanotrophy in a high-latitude fen peatland

The dynamics of methane (CH 4 ) cycling in high-latitude peatlands through different pathways of methanogenesis and methanotrophy are still poorly understood due to the spatiotemporal complexity of microbial activities and biogeochemical processes. Additionally, long-term in situ measurements within soil columns are limited and associated with large uncertainties in microbial substrates (e.g. dissolved organic carbon, acetate, hydrogen). To better understand CH 4 cycling dynamics, we first applied an advanced biogeochemical model, ecosys , to explicitly simulate methanogenesis, methanotrophy, and CH 4 transport in a high-latitude fen (within the Stordalen Mire, northern Sweden). Next, to explore the vertical heterogeneity in CH 4 cycling, we applied the PCMCI/PCMCI+ causal detection framework with a bootstrap aggregation method to the modeling results, characterizing causal relationships among regulating factors (e.g. temperature, microbial biomass, soil substrate concentrations) through acetoclastic methanogenesis, hydrogenotrophic methanogenesis, and methanotrophy, across three depth intervals (0–10 cm, 10–20 cm, 20–30 cm). Our results indicate that temperature, microbial biomass, and methanogenesis and methanotrophy substrates exhibit significant vertical variations within the soil column. Soil temperature demonstrates strong causal relationships with both biomass and substrate concentrations at the shallower depth (0–10 cm), while these causal relationships decrease significantly at the deeper depth within the two methanogenesis pathways. In contrast, soil substrate concentrations show significantly greater causal relationships with depth, suggesting the substantial influence of substrates on CH 4 cycling. CH 4 production is found to peak in August, while CH 4 oxidation peaks predominantly in October, showing a lag response between production and oxidation. Overall, this research provides important insights into the causal mechanisms modulating CH 4 cycling across different depths, which will improve carbon cycling predictions, and guide the future field measurement strategies.

54 ENVIRONMENTAL SCIENCES↗