Search NASA⌕ Search

SEARCH · Search NASA

Results for “solid growth”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Space processing of electronic materials

The bulk growth of solid solution alloys of mercury telluride and cadmium telluride is discussed. These alloys are usually described by the formula Hg1-xCdxTe, and are useful for the construction of infrared detectors. The electronic energy band gap can be controlled between zero and 1.6 electron volts by adjusting the composition x. The most useful materials are at x approximately 20%, suitable for detection wavelengths of about 10 micrometers. The problems of growing large crystals are rooted in the wide phase diagram of the HgTe-CdTe pseudobinary system which leads to exaggerate segregation in freezing, constitutional supercooling, and other difficulties, and in the high vapor pressure of mercury at the growth temperatures, which leads to loss of stoichiometry and to the necessity of working in strong, pressure resistant sealed containers.

Holland, L. R.↗
NASA NTRS1975

Interfacial impurities and the reaction between Si and evaporated Al

As commonly formed, the interface between substrate Si and evaporated Al is laden with impurities. Subsequent heating causes modest dissolution of Si into solid Al, the dissolution morphology being influenced by the interface impurities. In the present experiments, the amount of Si dissolving was considerably enhanced, causing sufficient interface movement to carry most interfaces clear of the original impurities. Under these conditions, the Si/Al interface assumes, during brief heat treatment, a simple shape composed of a few 111 plane-type facets. Such Si/Al interfaces produced in situ should be useful for low-temperature solid-state growth of Si.

Best, J. S.↗
NASA NTRS1980

Preparation of monotectic alloys having a controlled microstructure by directional solidification under dopant-induced interface breakdown

Monotectic alloys having aligned spherical particles of rods of the minor component dispersed in a matrix of the major component are prepared by forming a melt containing predetermined amounts of the major and minor components of a chosen monotectic system, providing in the melt a dopant capable of breaking down the liquid solid interface for the chosen alloy, and directionally solidfying the melt at a selected temperature gradient and a selected rate of movement of the liquid-solid interface (growth rate). Shaping of the minor component into spheres or rods and the spacing between them are controlled by the amount of dopant and the temperature gradient and growth rate values. Specific alloy systems include Al Bi, Al Pb and Zn Bi, using a transition element such as iron.

Parr, R. A.↗
NASA NTRS1986

Oxidation and embrittlement of Ti-6Al-2Sn-4Zr-2Mo alloy

A thermogravimetric analysis monitoring study has been conducted for Ti-6Al-2Sn-4Zr-2Mo in the 593-760 C range, with a view to its total oxidation kinetics in laboratory air. In addition, tensile elongation was obtained for selected foil specimens after their exposure to simulated Space Shuttle reentry conditions. The total weight gain with time exhibited two parabolic stages separated by a transient region which is the result of a simultaneous increase in the parabolic growth rate constant for the oxide and in oxygen solubility at the oxide-metal interface. A model for the total oxidation kinetics accounting for the two individual components (oxide growth and solid solution formation) is proposed; the activation energy for oxygen diffusion in the alpha-solid solution is shown to approximate the activation energy for the degradation of tensile elongation of the alloy in its foil gage condition.

Shenoy, R. N.↗
NASA NTRS1989

Fluid flow in solidifying monotectic alloys

Use of a two-wavelength holographic technique results in a simultaneous determination of temperature and composition profiles during directional solidification in a system with a miscibility gap. The relationships among fluid flow, phase separation, and mass transport during the solidification of the monotectic alloy are discussed. The primary sources of fluid motion in this system are buoyancy and thermocapillary forces. These forces act together when phase separation results in the formation of droplets (this occurs at the solid-liquid interface and in the bulk melt). In the absence of phase separation, buoyancy results from density gradients related to temperature and compositional gradients in the single-phase bulk melt. The effects of buoyancy are especially evident in association with water- or ethanol-rich volumes created at the solid-liquid growth interface.

Ecker, A.↗
NASA NTRS1990

Solid-support substrates for plant growth at a lunar base

Zeoponics is only in its developmental stages at the Johnson Space Center and is defined as the cultivation of plants in zeolite substrates that contain several essential plant growth cations on their exchange sites, and have minor amounts of mineral phases and/or anion-exchange resins that supply essential plant growth anions. Zeolites are hydrated aluminosilicates of alkali and alkaline earth cations with the ability to exchange most of their constituent exchange cations as well as hydrate/dehydrate without change to their structural framework. Because zeolites have extremely high cation exchange capabilities, they are very attractive media for plant growth. It is possible to partially or fully saturate plant-essential cations on zeolites. Zeoponic systems will probably have their greatest applications at planetary bases (e.g., lunar bases). Lunar raw materials will have to be located that are suited for the synthesis of zeolites and other exchange resings. Lunar 'soil' simulants have been or are being prepared for zeolite/smectite synthesis and 'soil' dissolution studies.

Ming, D. W.↗
NASA NTRS2000

Vapor Growth and Characterization of ZnSeTe Solid Solutions

Six ZnSe(1-x)Te(x) crystals were grown by the physical vapor transport technique. For each of the source material compositions, x = 0.10, 0.20 and 0.30, two crystals were grown - one under the horizontal and the other under the vertical stabilized configurations. The axial and radial compositional uniformity were measured by precision density measurements, wavelength dispersive X-ray spectroscopy (WDS) and optical transmission mappings. The measured radial ZnTe content was quite uniform for all the grown crystals except the horizontally grown crystal for x = 0.30. The WDS results on this crystal indicated a core with uniform ZnTe content, about 0.38, surrounded by a thin region of high ZnTe content with x = 0.8. This feature was confirmed by the SEM back scattering electron images. For the three source compositions the axial compositional variations for the vertically grown crystals were more uniform than that for the horizontally grown crystals. The measured compositions in the crystals grown from source composition of x = 0.10 suggest that the transport mechanism in the system can not be interpreted by a simple one-dimensional diffusion limited model.

Su, Ching-Hua↗
NASA NTRS1999

Nucleation, Growth, Annealing, and Coagulation of Refractory Oxides and Metals: Recent Experimental Progress and Applications to Astrophysical Systems

Starting with cooling, refractory vapors diluted in significant quantities of H and He there are four processes that most natural systems will undergo: nucleation, growth, annealing, and coagulation. Nucleation is the processes by which the first stable refractory nuclei form in the vapor. These are the seeds onto which the remaining vapors will condense during the growth stage. Solids of any composition will try to arrange themselves into the least energetic configuration, provided that there is sufficient energy available to support such processes as diffusion and the breaking of chemical bonds. There is a significant activation energy associated with the annealing process in refractory solids due to the relatively high energy of the chemical bonds in solids. The grains formed in most cosmochemical systems are extremely small and often tightly coupled to the gas. Because of their small physical cross sections coagulation may be a very slow process unless there is another driving force involved in addition to normal Brownian motion. In what follows we will briefly cover each of these four stages for refractory oxide and metal grains, although in inverse order.

Nuth, J. A.↗
NASA NTRS2001

Structural Fluctuations and Thermophysical Properties of Molten II-VI Compounds

Recently, in support of the microgravity experiment entitled "Crystal Growth of Selected 11-VI Semiconducting Alloys by Directional Solidification," the viscosity of HgZnTe pseudobinary melt was measured using an oscillating-cup viscometer at NASA/Marshall Space Flight Center (MSFC). An unexpected time drift of the measured viscosity, which shows a slow relaxation phenomena at temperatures near the liquidus point, was reproducibly observed. Two sets of data were obtained by cooling the Hg(0.84)Zn(0.16)Te melt from 850 C and stabilizing at temperatures of 790 C, which is just above the liquidus temperature, and stabilizing at temperature of 810 C. While it took one day to reach equilibration at 810 C, five days were required at 790 C A similar relaxation phenomenon was also observed in the measured density of the same liquid. Furthermore, in the density measurements of the HgCdTe melts, which is the pseudobinary system studied in another flight experiment entitled "Growth of Solid Solution Single Crystals," a negative thermal expansion was reported. The liquid density increases from the liquidus point to a maximum value at a temperature approximately 700 C above the liquidus, where normal thermal expansion progressively resumes.

Su, Ching-Hua↗
NASA NTRS1998

Formation of Jupiter and Saturn

An overview of current theories of the formation of our Solar System, with emphasis on giant planets, is presented. The most detailed models are based upon observations of planets and smaller bodies within our own Solar System and of young stars and their environments. Terrestrial planets are believed to grow via pairwise accretion until the spacing of planetary orbits becomes large enough that the configuration is stable for the age of the system. Giant planets begin their growth as do terrestrial planets, but they become massive enough that they are able to accumulate substantial amounts of gas before the protoplanetary disk dissipates. Larger disk mass allows for faster growth of solid planetary bodies. The ability of a solid planet to trap gas from the protoplanetary disk increases rapidly as its mass increases (because the depth of its gravitational potential well increases), but decreases as the planetesimal accretion rate is increased (as it becomes hotter). The net effect of increasing disk mass is that gas giant planets form more rapidly, but with larger core masses. Observations of circumstellar disks suggest an upper bound on the time available prior to dissipation of the gas, and planetary models place upper limits on core sizes. Together, these constraints suggest that Jupiter and Saturn formed in 1-10 million years, and the density of solids in the region of their formation was a few times as large as the lower bound provided by the traditional minimum mass nebula.

Lissauer, Jack J.↗
NASA NTRS1998

Formation of Jupiter and Saturn

An overview of current theories of the formation of our Solar System, with emphasis on giant planets, is presented. The most detailed models are based upon observations of planets and smaller bodies within our own Solar System and of young stars and their environments. Terrestrial planets are believed to grow via pairwise accretion until the spacing of planetary orbits becomes large enough that the configuration is stable for the age of the system. Giant planets begin their growth as do terrestrial planets, but they become massive enough that they are able to accumulate substantial amounts of gas before the protoplanetary disk dissipates. Larger disk mass allows for faster growth of solid planetary bodies. The ability of a solid planet to trap gas from the protoplanetary disk increases rapidly as its mass increases (because the depth of its gravitational potential well increases), but decreases as the planetesimal accretion rate is increased (as it becomes hotter). The net effect of increasing disk mass is that gas giant planets form more rapidly, but with larger core masses. Observations of circumstellar disks suggest an upper bound on the time available prior to dissipation of the gas, and planetary models place upper limits on core sizes. Together, these constraints suggest that Jupiter and Saturn formed in 1 - 10 million years, and the density of solids in the region of their formation was a few times as large as the lower bound provided by the traditional minimum mass nebula.

Lissauer, Jack J.↗
NASA NTRS1973

Study of single crystals of metal solid solutions

The growth of single crystals of relatively high melting point metals such as silver, copper, gold, and their alloys was investigated. The purpose was to develop background information necessary to support a space flight experiment and to generate ground based data for comparison. The ground based data, when compared to the data from space grown crystals, are intended to identify any effects which zero-gravity might have on the basic process of single crystal growth of these metals. The ultimate purposes of the complete investigation are to: (1) determine specific metals and alloys to be investigated; (2) grow single metal crystals in a terrestrial laboratory; (3) determine crystal characteristics, properties, and growth parameters that will be effected by zero-gravity; (4) evaluate terrestrially grown crystals; (5) grow single metal crystals in a space laboratory such as Skylab; (6) evaluate the space grown crystals; (7) compare for zero-gravity effects of crystal characteristics, properties, and parameters; and (8) make a recommendation as to production of these crystals as a routine space manufacturing proceses.

Doty, J. P.↗
NASA NTRS1999

Growth and Characterization of Bulk GeSi Solid Solutions

In this work we have grown and characterized several GeSi samples in order to investigate the effects that Silicon concentration, applied magnetic field, and liquid encapsulation have on crystalline quality. Characterization techniques include NDIC microscopy and microprobe spectroscopy. Two samples were grown with a Silicon concentration of approximately 3% and are compared to previous growths having a Silicon fraction of approximately 5%. Growth conditions for one of these samples was varied with the presence of an external applied magnetic field to investigate the possibility of magnetic field damping. A comparison between these two ingots, and with previously grown material, revealed no clear improvement in sample crystalline quality. Three additional samples were grown using a CaCl2 liquid encapsulation technique that produced GeSi material with improved structural quality over previous samples. Comparisons to prior non-encapsulation grown material, details of our methodology, and suggestions for further improvements are discussed.

Ritter, Timothy M.↗
NASA NTRS1986

Determination of Solid Rocket Motor (SRM) case segment growth

Presented is an assessment of case growth for two D6AC steel SRM case segments with multiple flight use and a comparison of these two cases with two new cases. Dimensional changes in the sealing diameter areas were recorded for the used cases and after hydroproofing of the new cases.

Mitchell, L. H.↗
NASA NTRS1986

Growth behavior of surface cracks in the circumferential plane of solid and hollow cylinders

Experiments were conducted to study the growth behavior of surface fatigue cracks in the circumferential plane of solid and hollow cylinders. In the solid cylinders, the fatigue cracks were found to have a circular arc crack front with specific upper and lower limits to the arc radius. In the hollow cylinders, the fatigue cracks were found to agree accurately with the shape of a transformed semiellipse. A modification to the usual nondimensionalization expression used for surface flaws in flat plates was found to give correct trends for the hollow cylinder problem.

Forman, R. G.↗
NASA NTRS1973

VLS /vapor-liquid-solid/ - Newly discovered growth mechanism on the lunar surface.

A probable vapor-liquid-solid (VLS) type of growth has been discovered for the first time in nature on the surface of lunar rock 15015. Scanning electron microprobe and energy dispersive x-ray data indicate that the growth occurs as metallic iron stalks from about 0.015 to 0.15 micrometer in diameter, with bulbous tips consisting of a mixture of iron and sulfur and measuring from about 0.03 to 0.2 micrometer in diameter. The stalk length is two to ten times the bulb diameter.

Carter, J. L.↗