SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
U.s. standard atmosphere, 1962 - properties, development of gravity and geopotential, systematic variation
This paper evaluates the ruggedness testing of the recently released ASTM International E3098 Standard Test Method for Mechanical Uniaxial Pre-strain and Thermal Free Recovery of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors: strain rate (ė), heating and cooling rates (Ṫ heat and Ṫ cool , respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (t hold ), and minimum load (F min ) imparted on the samples. The results indicate that the strain rate factor had no effect on any result variable, whereas the minimum load factor had a large effect on several result variables including the austenite start and martensite finish temperatures as well as most of the strain measurements from the thermal cycle. The lower cycle temperature factor had a large effect on the stress at maximum strain during pre-straining (e i ), denoted by S i , at ~7.2 MPa, as well as the A f , at 5.47 °C. Closely following the LCT effect, Ṫ heat was found to have a large effect on the austenite start temperature (A s ), at a value of ~2.72 °C. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test method are presented.
The importance of data curation has been recognized in multiple areas of research; however, the discussion of this important issue is only beginning to emerge in materials science. In this Perspective, we highlight the benefits of using the standardized data curation protocols in materials science and discuss current gaps in accurate and reproducible data reporting using case studies drawn from high-impact materials science papers and well-known databases such as the Crystallography Open Database (COD) and the Cambridge Structural Database (CSD). We argue that both experimental and computational materials scientists need to embrace a culture of rigorous data curation as part of modern research data management. We propose a sample data curation pipeline for materials chemistry and illustrate its use by creating two new materials chemistry databases. Here, we hope that this perspective will serve to catalyze further discussion and promote the continuous development of rigorous data curation practices within the materials science research community. We posit that adherence to best practices of data curation will promote and enhance the reliability, reproducibility, and integrity of materials research and enable the development of reliable AI and machine learning models that critically depend on the use of quality data.
ABSTRACT We use 38 C iv quasar (QSO) reverberation-mapped observations, which span eight orders of magnitude in luminosity and the redshift range 0.001064 ≤ z ≤ 3.368, to simultaneously constrain cosmological-model and QSO radius–luminosity (R–L) relation parameters in six cosmological models, using an improved technique that more correctly accounts for the asymmetric errors bars of the time-lag measurements. We find that R–L relation parameters are independent of the cosmological models used in the analysis and so the R–L relation can be used to standardize the C iv QSOs. The C iv QSO cosmological constraints are consistent with those from Mg ii QSOs, allowing us to derive joint C iv + Mg ii QSO cosmological constraints which are consistent with currently accelerated cosmological expansion, as well as consistent with cosmological constraints derived using better-established baryon acoustic oscillation (BAO) and Hubble parameter [H(z)] measurements. When jointly analysed with H(z) + BAO data, current C iv + Mg ii QSO data mildly tighten current H(z) + BAO data cosmological constraints.
We formulate a perturbative framework for the flavor transformation of the standard active three neutrinos but with a non-unitary flavor mixing matrix, a system which may be relevant for the leptonic unitarity test. We use the $\alpha$ parametrization of the non-unitary matrix and take its elements $\alpha_{\beta \gamma}$ ($\beta,\gamma = e,\mu,\tau$) and the ratio $\epsilon \simeq \Delta m^2_{21} / \Delta m^2_{31}$ as the small expansion parameters. Two qualitatively new features that hold in all the oscillation channels are uncovered in the probability formula obtained to first order in the expansion: (1) The phases of the complex $\alpha$ elements always come into the observable in the particular combination with the $\nu$SM CP phase $\delta$ in the form $[e^{- i \delta } \bar{\alpha}_{\mu e}, ~e^{ - i \delta} \bar{\alpha}_{\tau e}, ~\bar{\alpha}_{\tau \mu}]$ under the Particle Data Group convention of a unitary $\nu$SM mixing matrix. (2) The diagonal $\alpha$ parameters appear in particular combinations $\left( a/b - 1 \right) \alpha_{ee} + \alpha_{\mu \mu}$ and $\alpha_{\mu \mu} - \alpha_{\tau \tau}$, where $a$ and $b$ denote, respectively, the matter potential due to charged current and neutral current reactions. This property holds only in the unitary evolution part of the probability, and there is no such feature in the genuine non-unitary part, while the $\delta$–$\alpha$ parameter phase correlation exists for both. The reason for such remarkable stability of the phase correlation is discussed.
Measurement of otolith activity as indicated by ocular counterrolling in response to body tilt within force field of zero G, one-half G, and standard G - extralabyrinthine factors
This monograph contains standards for software development and engineering. The book sets forth rules for design, specification, coding, testing, documentation, and quality assurance audits of software; it also contains detailed outlines for the documentation to be produced.
Calibrations by four U.S. laboratories of four hot-cathode ion gauges, in the range 0.07-13 mPa, showed systematic differences among laboratories that were much larger than the expected error of any one calibration. They also suggested that any of the four gauges tested, if properly packaged and shipped, was able to serve as a transfer standard with probable error of 2%. A second comparison was made of the calibrations by two U.S. laboratories of some other gauges that had also been calibrated by the National Physical Laboratory, England. Results did not permit conclusive determination of whether differences were due to the laboratories or to changes in the gauges.
An investigation is being conducted to determine the altitude performance characteristics of the British Nene II engine and its components. The present paper presents the preliminary results obtained using a standard jet nozzle. The test results presented are for conditions simulating altitudes from sea level to 60,000 feet and ram pressure ratios from 1.0 to 2.3. These ram pressure ratios correspond to flight Mach numbers between zero and 1.16 assuming a 100 percent ram recovery.
This paper evaluates the ruggedness testing of the newly released ASTM International E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors of strain rate (ė), heating and cooling rates (T(sub heat) and T(sub cool), respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (t(sub hold)), and minimum load (F(sub min)) imparted on the samples. The results indicate that the hold time factor had no effect on any result variable. The minimum load factor, alternatively, had the greatest effect on several result variables, with the greatest influence on the strains at martensite start and finish (strain variation ~0.1 percent), and the strains at the upper and lower cycle temperatures (strain variation of 0.14 percent). The UCT was found to have a large effect on the austenite and martensite finish tangent line and data intersect, denoted by A(sub f(sup *)) and M(sub f(sup*)), by ~17 and 4 °C, respectively. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test methods are presented.
This paper evaluates the ruggedness testing of the newly released ASTM International E3097 Standard Test Method for Mechanical Uniaxial Constant Force Thermal Cycling of Shape Memory Alloys. The ruggedness experiment was designed with eight runs in two replicates, consisting of seven factors of strain rate (ė), heating and cooling rates (Ṫ(heat) and Ṫ(cool), respectively), upper and lower cycle temperatures (UCT and LCT, respectively), hold time (thold), and minimum load (Fmin) imparted on the samples. The results indicate that the hold time factor had no effect on any result variable. The minimum load factor, alternatively, had the greatest effect on several result variables, with the greatest influence on the strains at martensite start and finish (strain variation ~0.1 percent), and the strains at the upper and lower cycle temperatures (strain variation of 0.14 percent). The UCT was found to have a large effect on the austenite and martensite finish tangent line and data intersect, denoted by Af* and Mf*, by ~17 and 4 °C, respectively. The testing methodology, analysis techniques, and resulting conclusions on the ruggedness of the test methods are presented.
Self-ion irradiation is widely used as a method to simulate neutron damage in reactor structural materials. Accelerator-based simulation of void swelling, however, introduces a number of neutron-atypical features which require careful data extraction and in some cases introduction of innovative irradiation techniques to alleviate these issues. We briefly summarize three such atypical features: defect imbalance effects, pulsed beam effects, and carbon contamination. The latter issue has just been recently recognized as being relevant to simulation of void swelling and is discussed here in greater detail. It is shown that carbon ions are entrained in the ion beam by Coulomb force drag and accelerated toward the target surface. Beam-contaminant interactions are modeled using molecular dynamics simulation. By applying a multiple beam deflection technique, carbon and other contaminants can be effectively filtered out, as demonstrated in an irradiation of HT-9 alloy by 3.5 MeV Fe ions.
No abstract available
Corn stover is expected to supply much of the cellulosic biomass required to meet the 61 billion liters per year target under the US Energy Independence and Security Act. The Act also requires that cellulosic biofuels achieve a greenhouse gas (GHG) reduction of 60% compared to gasoline. If corn stover is harvested for biofuels, it can no longer help replenish soil organic matter, and net soil carbon emissions increase. So meeting the GHG reduction target is a concern. We studied the effect of stover removal on overall GHG emissions of corn stover ethanol systems in the 12-state Corn Belt region. Even at a stover removal rate of 66%, no more than 20 billion liters can be annually produced while simultaneously satisfying the 60% GHG reduction. Moreover, no GHG reduction relative to gasoline occurs in short time periods. The GHG benefits of corn stover ethanol only appear after longer time periods.
Not Available
No abstract prepared.
Platinum group metal (PGM)-free electrocatalysts for the oxygen reduction reaction at the polymer electrolyte fuel cell cathode have shown substantial improvements in activity—especially those derived from transition metals, nitrogen and carbon. However, their stability and durability remain insufficient. A key to enabling future improvements and performance comparisons lies in the development of test protocols that are relevant to the operating conditions of the fuel cell cathode, can be completed within a reasonable time and are ubiquitously adopted. Here we propose and validate such protocols, designed with special attention to typical catalyst degradation mechanisms of PGM-free catalysts. The results of the cross-laboratory validation study using two different catalysts attest to the strength and feasibility of the proposed approach. We hope that the information provided here can serve as a broad and effective platform for assessing the performance and durability of PGM-free catalysts for polymer electrolyte fuel cells.
Not provided.