Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface confinement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Comparative Studies for the Sodium and Potassium Atmospheres of the Moon and Mercury

A summary discussion of recent sodium and potassium observations for the atmospheres of the Moon and Mercury is presented with primary emphasis on new full-disk images that have become available for sodium. For the sodium atmosphere, image observations for both the Moon and Mercury are fitted with model calculations (1) that have the same source speed distribution, one recently measured for electron-stimulated desorption and thought to apply equally well to photon-stimulated desorption, (2) that have similar average surface sodium fluxes, about 2.8 x 10(exp 5) to 8.9 x 10(exp 5) atoms cm(exp -2)s(exp -1) for the Moon and approximately 3.5 x 10(exp 5) to 1.4 x 10(exp 6) atoms cm(exp -2)s(exp -1) for Mercury, but (3) that have very different distributions for the source surface area. For the Moon, a sunlit hemispherical surface source of between approximately 5.3 x 10(exp 22) to 1.2 x 10(exp 23) atoms/s is required with a spatial dependence at least as sharp as the square of the cosine of the solar zenith angle. For Mercury, a time dependent source that varies from 1.5 x 10(exp 22) to 5.8 x l0(exp 22) atoms/s is required which is confined to a small surface area located at, but asymmetrically distributed about, the subsolar point. The nature of the Mercury source suggest that the planetary magnetopause near the subsolar point acts as a time varying and partially protective shield through which charged particles may pass to interact with and liberate gas from the planetary surface. Suggested directions for future research activities are discussed.

Smyth, William H.↗
NASA NTRSDate not supplied

Developing Wear-Resistant Coatings for Lunar Dust Tolerant Applications

Materials resistant to the harsh lunar environment are needed to support long duration, sustainable missions on the Moon’s surface. Lunar dust poses a significant threat to the durability of components and vehicles due to its fine, jagged morphology and highly abrasive nature. These properties result in particles eroding, adhering and/or embedding onto component surfaces and into device confined geometries (e.g., gear housing, interlocking systems, etc.) potentially leading to premature failure. The aim of this work is to identify and characterize wear-resistant materials for use as protective coatings to minimize abrasion caused by lunar dust.Concurrently, testing and evaluation methods will be devised to elucidate and mimic aspects of lunar dust degradation, including particle embedding, gouging and erosion caused by high velocity impact events. Discussion on balancing the need for dust management and tolerance versus dust adhesion mitigation will be shared in context of relevant lunar applications within the NASA Lunar Occupancy Dust Surface Separation Technologies (LO-DuSST) effort, which is part of a NASA-wide effort to enable a sustained lunar presence through the Lunar Surface Innovation Initiative (LSII).

Materials, Coatings, lunar dust management/mitigat↗
NASA NTRSDate not supplied

Protective Coatings for Mitigating Lunar Dust Abrasion and Adhesion

Materials resistant to the harsh lunar environment are needed to support long duration, sustainable missions on the Moon’s surface. Lunar dust poses a significant threat to the durability of components and vehicles due to its fine, jagged morphology and highly abrasive nature. These characteristics result in particles eroding, adhering and/or embedding onto component surfaces and into device confined geometries (e.g., gear housing, interlocking systems, etc.) potentially leading to premature failure. The aim of this work is to identify and characterize wear-resistant materials, including advanced ceramics, for use as protective coatings to minimize abrasion and adhesion caused by lunar dust. Results from testing and evaluation methods devised to elucidate and mimic aspects of lunar dust degradation, including adhesion, abrasion and erosion, as well as the lunar environment, will be presented. Discussion on balancing the need for dust management and tolerance versus dust adhesion mitigation will be shared in context of relevant lunar applications within the NASA Lunar Occupancy Dust Surface Separation Technologies effort, which is part of a NASA-wide effort to enable a sustained lunar presence through the Lunar Surface Innovation Initiative.

lunar dust mitigation↗
NASA NTRSDate not supplied

Molten Salt Lattice Confinement Fusion (LCF) Fast Fission Reactor for Lunar and Planetary Surface Power

Molten salt fission reactors (MSR) have been suggested for lunar and planetary surface power systems. They have the advantage of operating at high temperature, for efficient thermal-electrical conversion, low pressure, long-lived with high nuclear fuel burnup. MSR are often designed to breed fissile 233U from natural 232Th by neutron capture and  decay via: 232Th(n,)233Th(,)233Pa(,)233U Unfortunately, this process requires 233Pa isotope separation and segregation to decay to 233U. This requirement prevents additional neutron capture that interferes with 233U breeding. Instead, Wooley’s sub-critical, fast fission, molten salt reactor would use externally generated tokamak fusion neutrons1,2 to fission all actinides.We propose a simpler fusion-fast-fission sub-critical reactor that generates fast neutrons in situ from lattice confinement fusion (LCF) to fission fertile and fissile actinides. This hybrid reactor doesn't require enriched 235U fissile pins to initiate fis-sion reactions, nor 233Pa separation and segregation during operation. Like Wooley’s, this hybrid reactor “burns” natural uranium (238U) or thorium (232Th) which avoids uranium enrichment and additional fissile material launch safety and security costs. The LCF neutron source is initiated by bremsstrahlung photoneutrons (Fig. 1)3 or isotopic neutron sources in electron-screened lattices (Fig. 2)4,5. Alternatively, the electrolytic Pd-deuterium co-deposition6protocol fast fissions7 both 232Th and 238U. However, an aqueous electrolyte-based system, without pressurization similar to conventional pressurized water fission reactors, is incapable of high temperatures due to the boiling point of the electrolyte slightly over 100 C. Molten salts can be used instead as was demonstrated at the University of Hawaii8 using a variety of Ni and Pd cathodes in lithiated, hydrided and deuterated salts. These salts have melting points often exceeding 500C making them suitable to efficiently produce electrical power9 through either Advanced Stirling Genera-tors (< 100 kWe) or closed-Brayton Cycle (> 100 kWe). This hybrid reactor could power a wide range of lunar or Martian applications from unmanned in-struments, to charging vehicles and entire facilities such as human habitats or in situ resource utilization. The power conversion cycles are Carnot Cycle limited, but generally 30% efficient at best. However, waste heat on the moon or Mars is important to surviving either two-week lunar nights or Martian nights as well as providing process heat for mineral extraction and “living off the land”

Lawrence Forsley↗
NASA NTRS1976

Plasma core reactor applications

Analytical and experimental investigations were conducted to demonstrate the feasibility of fissioning uranium plasma core reactors and to characterize space and terrestrial applications for such reactors. Uranium hexafluoride fuel is injected into core cavities and confined away from the surface by argon buffer gas injected tangentially from the peripheral walls. Radiant heat transfer calculations were performed for a six-cavity reactor configuration. Axial working fluid channels are located along a fraction of each cavity peripheral wall. Results of calculations for outward-directed radiant energy fluxes corresponding to radiating temperatures of 2000 to 5000 K indicate total operating pressures from 80 to 650 atm, centerline temperatures from 6900 to 30,000 K, and total radiated powers from 25 to 2500 MW, respectively. Applications are described for this type of reactor such as (1) high-thrust, high specific impulse space propulsion, (2) highly efficient systems for generation of electricity, and (3) hydrogen or synthetic fuel production systems using the intense radiant energy fluxes.

Latham, T. S.↗
NASA NTRS1985

Mechanisms of Basalt-plains Ridge Formation

The morphologic similarities between the Columbia Plateau ridges and ridges on the Moon, Mercury and Mars form a strong basis for the interpretation of basalt-plains ridges as compressional folds. The basalt-plains ridges appear to have formed on competent flood basalt units deformed at the surface with essentially no confining pressure. Estimates of compressive strain for planetary ridges range from a few tenths of a percent on the Moon to up to 0.4% on Mars, to as high as 35% for Columbia Plateau folds with associated thrust faults. Such values have strong implications for both deformational mechanisms as well as for the source of stress. Deformational mechanisms that will attempt to account for the morphology, fold geometry, possible associated thrust faulting and regular spacing of the basalt-plains ridges on the terrestrial planets are under investigation.

Watters, T. R.↗
NASA NTRS1988

Current-driven resistive ballooning modes in axially bounded solar flare plasmas

The most unstable current-driven resistive modes of an axially bounded coronal loop are found in computer simulations to exhibit the spatial structure of ballooning modes. The observed modes are not confined to mode rational surfaces, but instead have broad radial extent. A theory assuming ballooning mode spatial structure predicts that a minimum current should be required for linear instability, and that, when the mode is unstable, the linear growth rate scales linearly with the resistivity eta below a critical resistivity, and scales as cu root of eta for larger resistivities. Both predictions are borne out by simulation results. Both theory and simulation analyses of the mode suggest that the strong radial structure of the mode near the ends of the system is the primary contributing factor to the instability of the mode. A helical current sheet is formed in the nonlinear evolution of the mode near the edge of the current channel and is accompanied by a strong radial gradient in the current and partial current reversal.

Otani, Niels F.↗
NASA NTRS1988

Centaur in-tank explosion flow fields within STS and Titan 4 payload spaces

Explosions are examined which result from the mixing of liquid hydrogen and liquid oxygen (LH2-LO2) such that the reactants are confined by the missile (CBM) body. Explosion which were confined by the ground surface (CBGS) were also studied, with results reported elsewhere. Initial attempts to predict the reported PYRO experimental results were unsuccessful. A new reaction energy addition hypothesis was then developed and tested. The results obtained provide reasonable agreement with the experiments both in the near and far field. Calculations were performed to predict the environment which would occur at the Galileo Radioisotope Thermoelectric Generator (RTG) location given a Centaur G' upper stage and an STS launch vehicle. It was concluded that the principle threat to the RTG in this environment would be the impact of a slug of LH2. No analyses were conducted to assess the response of the Galileo RTG to such an environment. It was shown that the flow field resulting from the failure of the Centaur G' tankage was benign. It was concluded that while the cryogen particle velocity was very high, the flow field density was extremely low. As a result, the dynamic pressure was a trivial eight psia.

Eck, M.↗
NASA NTRS1992

Reactions of atomic oxygen /O(3P)/ with polymer films

The reactions of polymer films with oxygen atoms are reviewed focusing on laboratory tests on polybutadienes with different amount of 1,4 or 1,2 double bonds and their polyalkenamer homologues, polyimide (Kapton), and a series of polyolefines with increasing fluorine content. It is found that etch rates increase with decrease in -CH=CH- unsaturation, starting with 1,4 -polybutadiene and reaching the maximum rate with polyethylene or ethylene-propylene rubber. IN polybutadienes with both 1,4 and 1,2 double bonds, the rate of O(3P)-induced etching is lower the higher the 1,2 content. The reactions are confined to the polymer surface.

Golub, Morton A.↗
NASA NTRS1928

Pressure Distribution Tests on PW-9 Wing Models Showing Effects of Biplane Interference

In this report tests are described in which the distribution of pressures over models of the wings of the PW-9 Airplane was investigated. The wing models were tested individually and in the biplane combination. The investigation was conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. It is concluded in this paper that the effect of biplane interference on the pressures on the wings is practically confined to the lower surface of the upper wing and the upper surface of the lower wing; that the overhanging portion of the upper wing is not greatly affected by the presence of the lower wing; and that a slight washing at the center section of the upper wing satisfactorily compensates for a reduced chord at this section (providing the airfoil section is not mutilated) and prevents a large reduction in the normal force over this portion of the wing.

Fairbanks, A J↗
NASA NTRS1998

Radiation-Driven Warping: Nonisothermal Disks - 2

Recent work by Pringle and by Maloney, Begelman, & Pringle has shown that geometrically thin, optically thick, accretion disks are unstable to warping driven by radiation torque from the central source. This work was confined to isothermal (i.e., surface density Sigma varies as R(sup -3/2) disks. In this paper we generalize the study of radiation-driven warping to include general power-law surface density distributions, Sigma varies as R(sup -delta).We consider the range from Delta = 3/2 (the isothermal case) to Delta = -3/2, which corresponds to a radiation-pressure-supported disk; this spans the range of surface density distributions likely to be found in real astrophysical disks. In all cases there are an infinite number of zero-crossing solutions (i.e., solutions that cross the equator), which are the physically relevant modes if the outer boundary of the disk is required to lie in a specified plane. However, unlike the isothermal disk, which is the degenerate case, the frequency eigenvalues for Delta does not equal 3/2 are all distinct. In all cases the location of the zero moves outward from the steady state (pure precession) value with increasing growth rate; thus, there is a critical minimum size for unstable disks. Modes with zeros at smaller radii are damped. The critical radius and the steady state precession rate depend only weakly on Delta. An additional analytic solution has been found for Delta = 1. The case Delta = 1 divides the solutions into two qualitatively different regimes. For Delta greater than or equal to 1, the fastest growing modes have maximum warp amplitude, close to the disk outer edge, and the ratio of Beta(sub max) to the warp amplitude at the disk inner edge, Beta(sub o), is much greater than 1. For Delta less than 1, Beta(sub max/Beta(sub o) approximately equals 1, and the warp maximum steadily approaches the origin as Delta decreases. This implies that nonlinear effects must be important if the warp extends to the disk inner edge for Delta greater than or equal to 1, but for Delta less than 1 nonlinearity will be important only if the warp amplitude is large at the origin. Because of this qualitative difference in the shapes of the warps, the effects of shadowing of the central source by the warp will also be very different in the two regimes of Delta. This has important implications for radiation-driven warping in X-ray binaries, for which the value of Delta characterizing the disk is likely to be less than unity. In real accretion disks the outer boundary condition is likely to be different from the zero-crossing condition that we have assumed. In accretion disks around massive black holes in active galactic nuclei, the disk will probably become optically thin before the outer disk boundary is reached, whereas in X-ray binaries there will be an outer disk region (outside the circularization radius) in which the inflow velocity is zero but angular momentum is still transported. We show that in both these cases the solutions are similar to the zero-crossing eigenfunctions.

Maloney, Philip R.↗
NASA NTRS2023

Protective Coatings for Lunar Dust Tolerance

Materials capable of withstanding the harsh lunar environment are critically needed to support long duration, sustainable missions on the Moon’s surface. Lunar dust significantly threatens the durability and reusability of components and vehicles due to possessing a fine, jagged morphology and highly abrasive nature. These characteristics result in the particles eroding, adhering and/or embedding onto component surfaces and into device confined geometries (e.g., gear housing, interlocking systems, etc.) potentially leading to premature failure. The aim of this study is to identify and characterize wear-resistant commercial-off-the-shelf (COTS) materials, including advanced ceramics, for use as protective coatings to minimize abrasion and adhesion caused by lunar dust. Preliminary testing that mimics various aspects of lunar dust degradation, such as abrasive wear and adhesion, suggests that COTS ceramic coatings can improve lunar dust tolerance and protect underlying metallic substrates.

Valerie. L. Wiesner↗
NASA NTRSDate not supplied

Dust-Proofing the Future: Materials Challenges for Lunar Exploration

As humanity expands its ventures into lunar exploration, the demand intensifies for materials capable of enduring extreme environmental and service conditions. The Moon’s surface presents numerous challenges, including ultra-high vacuum exposure, temperature extremes and intense radiation. Additionally, lunar regolith threatens component durability and reusability due to its abrasive nature. Lunar dust particles scoring, adhering or embedding into surfaces and within device-confined geometries, such as bearings, drive mechanisms and connectors, can cause premature component wear or failure. Furthermore, the interaction between the rocket plume and surface during vehicle landings and ascents creates severe erosive conditions near critical vehicle components and adjacent infrastructure. A key barrier hindering materials discovery for lunar dust tolerant applications is a lack of standard laboratory methods to evaluate material properties and performance under representative operating conditions. A case will be presented for research activities supporting identification, processing and characterization of candidate materials in conjunction with innovations in standardized testing and qualification. Results will highlight current and emerging test methods for simulating lunar dust exposure and component degradation, paving the way for a new generation of robust materials and coatings for space exploration.

lunar dust↗
NASA NTRS1992

The modulation of the low-latitude radiation budget by cloud and surface forcing on interannual time scales

Regionally confined interannual perturbations in the tropical radiation budget associated with east-west circulations are examined along with the forcing mechanisms of these perturbations in relation to surface and cloudiness variability. A zonal harmonic analysis of emitted longwave radiation emphasizes that these variations are largely controlled at the planetary wave scale. The overall effect leads to an approximately 50 deg/yr propagation phase speed that is considerably slower than the oceanic Kelvin wave capable of driving east-west longwave (LW) anomalies through SST feedback. Examination of the time-dependent radiative energetics over the tropics reveals that the aforementioned anomaly LW propagation is mainly due to cloud forcing associated with east-west circulation changes. Diabatic heating associated with coupled ocean-atmosphere feedback appears to be larger responsible for the LW anomaly propagation.

Sohn, Byung-Ju↗
NASA NTRSDate not supplied

Materials for Extreme Environments: Paving the Way for Lunar Exploration

As humanity expands its ventures into lunar and planetary exploration, the demand intensifies for resilient materials capable of enduring extreme environmental and service conditions. The Moon’s surface presents numerous challenges, including ultra-high vacuum exposure, temperature extremes and intense radiation. Additionally, lunar regolith poses a significant threat to component durability and reusability due to its abrasive nature. Lunar dust particles scoring, adhering, or embedding into surfaces and within device-confined geometries, such as bearings, drive mechanisms and connectors, can cause premature component wear or failure. Furthermore, the interaction between the rocket plume and the surface during vehicle landings and ascents creates severe erosive conditions near critical vehicle components and adjacent infrastructure. A key barrier hindering materials discovery for lunar dust tolerant applications is a lack of standard laboratory methods to evaluate material properties and performance under representative operating conditions. A case will be presented for research activities supporting identification, processing and characterization of candidate materials in conjunction with innovations in standardized testing and qualification. Results will highlight current and emerging test methods for simulating lunar dust exposure and component degradation, paving the way for a new generation of robust materials and coatings for space exploration.

Lunar dust↗
NASA NTRS1978

Computational flow development for unsteady viscous flows: Foundation of the numerical method

A procedure is presented for effective consideration of viscous effects in computational development of high Reynolds number flows. The procedure is based on the interpretation of the Navier-Stokes equations as vorticity transport equations. The physics of the flow was represented in a form suitable for numerical analysis. Lighthill's concept for flow development for computational purposes was adapted. The vorticity transport equations were cast in a form convenient for computation. A statement for these equations was written using the method of weighted residuals and applying the Galerkin criterion. An integral representation of the induced velocity was applied on the basis of the Biot-Savart law. Distribution of new vorticity, produced at wing surfaces over small computational time intervals, was assumed to be confined to a thin region around the wing surfaces.

Bratanow, T.↗
NASA NTRS1982

Use of high L.E.T. radiation to improve adhesion of metals to polytetrafluoroethylene

MgK alpha X-rays (1254 eV) and 2 keV electrons irradiate the surface of polytetrafluoro ethylene (PTFE). The damage is confined to a few tenths of a micron below the surface, and the doses exceed 10 to the eight power rad. X-ray Photoelectron Spectroscopy (XPS) of the irradiated surfaces and mass spectroscopy of the gaseous products of irradiation indicate that the damaged layer is crosslinked or branched PTFE. After either type of irradiation, the surface has enhanced affinity for metals and a lower contact angle with hexadecane. Tape pull tests show that evaporated Ni and Au films adhere better to the irradiated surface. XPS shows the Ni interacts chemically with PTFE forming NiF2 and possibly NiC. However, the gold adhesion and contact angle results indicate that the interaction is, at least in part, chemically nonspecific. Decreased contact angles on FEP Teflon crystallized against gold were attributed to either the presence of a polar oxygen layer or increased physical forces due to greater density. In the case of irradiated PTFE, no oxygen on the surface was observed. The crosslinked structure might, however, have a greater density, thus accounting for the observed increase in adhesion and wettability.

Wheeler, D. R.↗
NASA NTRS1948

Investigation of Effectiveness of Air-Heating a Hollow Steel Propeller for Protection Against Icing. 3: 25% Partitioned Blades

The icing protection obtained from an internally air-heated propeller blade partitioned to confine the heated air forward of 25-percent chord was investigated in the NACA Cleveland icing research tunnel. A production-model hollow steel propeller was modified with an Internal radial partition at 25-percent chord and with shank and tip openings to admit and exhaust the heated air. Temperatures were measured on the blade surfaces and in the heated-air system during tunnel icing conditions. Heat-exchanger effectiveness and photographs of Ice formations on the blades were obtained. Surface temperature measurements indicated that confining the heated air forward of the 25-percent chord gave.a more economical distribution of the applied heat as compared with unpartitioned and 50-percent partitioned blades, by dissipating a greater percentage of the available heat at the leading edge. At a propeller speed of 850 rpm, a heating rate of 7000 Btu per hour per blade at a shank air temperature of 400 F provided adequate Icing protection at ambient-air temperatures of 23 F but not at temperatures as low as 15 F. With the heating rate used, a heat-exchanger effectiveness of 77 percent was obtained as compared to 56 percent for 50-percent partitioned and 47 percent for unpartitioned blades.

Mulholland, Donald R.↗