Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface structure”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Surface structure of Sn doped β-Ga 2 O 3 (010) p(1×1) studied by quantitative low energy electron diffraction

Here, we have studied the surface structure of a single crystal β-Ga 2 O 3 (010) using quantitative Low Energy Electron Diffraction (LEED) and X-ray photoelectron spectroscopy (XPS). The XPS measurements show spectra typical of stoichiometric Ga 2 O 3 with a clean surface. LEED consistently shows a p(1x1) pattern, free of surface reconstruction. Quantitative LEED I(V) curves are acquired for 41 distinct diffraction spots. The experimental I(V) curves are compared to simulations over the first five layers. The best fits to the experimental LEED I(V) curves acquired at all diffraction spots are then used to calculate the interplanar relaxation and atomic rumpling. Significant atomic rumpling and interplanar relaxation are found over the first 5 atomic layers. As a result of rumpling a polarization of ~ 2 μC/cm 2 develops in the topmost surface layer. The structural results are in good agreement with previous density functional theory calculations and experimental X-ray photoelectron diffraction.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Changes in the surface structure of the heterogeneous body (diorite) under friction

Raman, infrared, and photoluminescent spectroscopy has been used to study changes in the surface structure of quartz diorite caused by friction. Before friction, the diorite surface layer has contained mainly quartz and feldspar crystals. After friction, some quartz and feldspar crystals have been destructed and replaced by a newly formed hydromica mineral with a low friction coefficient such as illite.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2017

Study of the formation of thermochemical laser-induced periodic surface structures on Cr, Ti, Ni and NiCr films under femtosecond irradiation

The formation of femtosecond laser-induced periodic surface structures (LIPSS’s) on Cr, Ti, Ni and NiCr films (with different Cr contents) is investigated. It is established that thermochemical LIPSS’s with periods of 950, 930 and 980 nm are formed, respectively, on the surfaces of titanium, chromium, and nichrome (with a chromium content of 20%); however, thermochemical LIPSS’s are not formed on the surfaces of nickel and nichrome with a low chromium content, although Raman data indicate that oxidation occurs in all cases. A weakly ordered ablated structure with a period of 250 – 300 nm is found to be formed on oxidised areas of thermochemical LIPSS’s in the case of chromium and nichrome (80/20). Experimental data on selective etching of thermochemical LIPSS’s on titanium and chromium films are presented. (paper)

36 MATERIALS SCIENCE↗
DOE OSTI2015

Study of the correlation parameters of the surface structure of disordered semiconductors by the two-dimensional DFA and average mutual information methods

The processes of self-organization of the surface structure of hydrogenated amorphous silicon are studied by the methods of fluctuation analysis and average mutual information on the basis of atomic-force-microscopy images of the surface. It is found that all of the structures can be characterized by a correlation vector and represented as a superposition of harmonic components and noise. It is shown that, under variations in the technological parameters of the production of a-Si:H films, the correlation properties of their structure vary as well. As the substrate temperature is increased, the formation of structural irregularities becomes less efficient; in this case, the length of the correlation vector and the degree of structural ordering increase. It is shown that the procedure based on the method of fluctuation analysis in combination with the method of average mutual information provides a means for studying the self-organization processes in any structures on different length scales.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Femtosecond laser induced periodic surface structures on multi-layer graphene

In this work, we present an observation of laser induced periodic surface structures (LIPSS) on graphene. LIPSS on other materials have been observed for nearly 50 years, but until now, not on graphene. Our findings for LIPSS on multi-layer graphene were consistent with previous reports of LIPSS on other materials, thus classifying them as high spatial frequency LIPSS. LIPSS on multi-layer graphene were generated in an air environment by a linearly polarized femtosecond laser with excitation wavelength λ of 840 nm, pulse duration τ of ∼150 fs, and a fluence F of ∼4.3–4.4 mJ/cm{sup 2}. The observed LIPSS were perpendicular to the laser polarization and had dimensions of width w of ∼30–40 nm and length l of ∼0.5–1.5 μm, and spatial periods Λ of ∼70–100 nm (∼λ/8–λ/12), amongst the smallest of spatial periods reported for LIPSS on other materials. The spatial period and width of the LIPSS were shown to decrease for an increased number of laser shots. The experimental results support the leading theory behind high spatial frequency LIPSS formation, implying the involvement of surface plasmon polaritons. This work demonstrates a new way to pattern multi-layer graphene in a controllable manner, promising for a variety of emerging graphene/LIPSS applications.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Friction-Induced Changes in the Surface Structure of Basalt and Granite

Friction-induced changes in the structure of the surface layer of basalt and granite samples extracted from a well in the triggered seismicity zone in the Koyna–Warna region, India, have been studied by infrared, Raman, and photoluminescence spectroscopy. It has been found that friction leads to a partial degradation of quartz, albite, and clinopyroxenes crystals. Instead of these crystals, a thin layer of a mineral with a low coefficient of friction—kaolinite—is formed on the surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2016

Surface, structural and mechanical properties of zirconium ablated by KrF excimer laser radiation

We study the effect of the ambient – dry (air) and wet (propanol) – environment on the surface, structural and mechanical properties of zirconium samples after irradiation with a KrF excimer laser (wavelength of 248 nm, pulse duration of 20 ns and repetition rate of 20 Hz). The samples are exposed to an increasing number of laser pulses varying from 500 to 2000 in both media. Various features of the treated targets such as surface morphology, chemical composition, crystalline structure and hardness are analysed by complementary characterisation techniques, such as scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS), X-ray diffraction (XRD), Raman spectroscopy and Vickers hardness tester, respectively. Surface morphology and hardness are explained on the basis of modifications in crystalinity, residual pressures and chemical properties of the sample surface after its irradiation. (interaction of laser radiation with matter)

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

Surface structures of magnetostrictive D0 3 -Fe 3 Ga(0 0 1)

First-principles total energy calculations and scanning tunneling microscopy experiments were performed to study the surface reconstruction of the magnetostrictive Fe 3 Ga alloy. The inverse magnetostrictive behavior was evaluated in the bulk by compressing and stretching its lattice parameter, showing an increase in magnetic moments as strain increases. Surface analysis demonstrates two thermodynamically stable surfaces, the (1 × 1) and (3 × 1). The (1 × 1) is an ideal FeGa terminated surface, whereas the (3 × 1) is also FeGa terminated but it has a first-layer Fe atom substituted by a Ga atom every three unit-cells, forming a row-like surface structure. Tersoff–Hamann scanning tunneling microscopy simulations were obtained and compared with experimental results. We found good agreement between theory and experiment, in which the distance between rows is ~12.3 Å. Theoretical findings suggest that the substrate-induced strain may increase the stability of the (3 × 1) reconstruction. Analysis of the magnetic moments in the reconstructions showed that their behavior is affected by a surface effect, as well as by the inverse magnetostriction of the structure. A good understanding of the FeGa surface reconstructions is an important step towards further improvements in magnetic storage devices and sensors.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Formation of microcraters and hierarchically-organized surface structures in TiNi shape memory alloy irradiated with a low-energy, high-current electron beam

The regularities of surface cratering in TiNi alloy irradiated with a low-energy, high-current electron beam (LEHCEB) in dependence on energy density and number of pulses are studied. LEHCEB processing of TiNi samples was carried out using RITM-SP facility. Energy density E{sub s} was varied from 1 to 5 J/cm{sup 2}, pulse duration was 2.5–3.0 μs, the number of pulses n = 1–128. The dominant role of non-metallic inclusions [mainly, TiC(O)] in the nucleation of microcraters was found. It was revealed that at small number of pulses (n = 2), an increase in energy density leads both to increasing average diameter and density of microcraters. An increase in the number of pulses leads to a monotonic decrease in density of microcraters, and, therefore, that of the proportion of the area occupied by microcraters, as well as a decrease in the surface roughness. The multiple LEHCEB melting of TiNi alloy in crater-free modes enables to form quasi-periodical, hierarchically-organized microsized surface structures.

36 MATERIALS SCIENCE↗
DOE OSTI2015

Influence of substrate microcrystallinity on the orientation of laser-induced periodic surface structures

The research in this paper deals with the angular dependence of the formation of laser-induced periodic surface structures (LIPSS) by linearly polarized nanosecond laser pulses on polycrystalline austenitic stainless steel. Incident angles ranging from 45° to 70° lead to the generation of superimposed merely perpendicular oriented LIPSS on steel as well as on monocrystalline (100) silicon which was used as a reference material. Additional extraordinary orientations of superimposing LIPSS along with significantly different periodicities are found on polycrystalline steel but not on (100) silicon. Electron backscatter diffraction measurements indicate that the expansion of these LIPSS is limited to the grain size and affected by the crystal orientation of the individual grains. Atomic force microscopy imaging shows that LIPSS fringe heights are in good agreement with the theoretically predicted penetration depths of surface plasmon polaritons into stainless steel. These results indicate that optical anisotropies must be taken into account to fully describe the theory of light-matter interaction leading to LIPSS formation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Generation of laser-induced periodic surface structures on transparent material-fused silica

We report on a comparison between simulated and experimental results for the generation of laser-induced periodic surface structures with low spatial frequency on dielectrics. Using the established efficacy factor theory extended by a Drude model, we determine the required carrier density for the generation of low spatial frequency LIPSS (LSFL) and forecast their periodicity and orientation. In a subsequent calculative step, we determine the fluence of ultrashort laser pulses necessary to excite this required carrier density in due consideration of the pulse number dependent ablation threshold. The later calculation is based on a rate equation including photo- and avalanche ionization and derives appropriate process parameters for a selective generation of LSFL. Exemplarily, we apply this approach to the generation of LSFL on fused silica using a 1030 nm femtosecond laser. The experimental results for the orientation and spatial periodicity of LSFL reveal excellent agreement with the simulation.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2021

Fermi Surface Structure and Isotropic Stability of Fulde-Ferrell-Larkin-Ovchinnikov Phase in Layered Organic Superconductor β''-(BEDT-TTF) 2 SF 5 CH 2 CF 2 SO 3

The Fermi surface structure of a layered organic superconductor β''-(BEDT-TTF) 2 SF 5 CH 2 CF 2 SO 3 was determined by angular-dependent magnetoresistance oscillations measurements and band-structure calculations. This salt was found to have two small pockets with the same area: a deformed square hole pocket and an elliptic electron pocket. Characteristic corrugations in the field dependence of the interlayer resistance in the superconducting phase were observed at any in-plane field directions. The features were ascribed to the commensurability (CM) effect between the Josephson vortex lattice and the periodic nodal structure of the superconducting gap in the Fulde–Ferrell–Larkin–Ovchinnikov (FFLO) phase. The CM effect was observed in a similar field region for various in-plane field directions, in spite of the anisotropic nature of the Fermi surface. The results clearly showed that the FFLO phase stability is insensitive to the in-plane field directions.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Synthesis of plasma polymerized PEM with pillar surface structure and its fuel cell performance

Highlights: • The surface morphology study of the membrane shows the presence of pillars on the surface of the membrane. • The membrane developed at 50 Watt shows good cell performance in fuel cell generating power density of 610 mW cm{sup −2}. • The pillar structure of the membrane also plays an indispensable role in the cell performance of the plasma polymerized PEM. - Abstract: Proton exchange membrane (PEM) is synthesized successfully by plasma polymerization technique in RF plasma discharge. The chemical composition of the prepared membranes is examined by FTIR analyses. SEM and AFM analysis of the membrane show the formation of a prominent pillar surface structure at high RF power. The pillar structure of the membrane also plays an indispensable role in the cell performance of the plasma polymerized PEM. The physical properties of the membrane developed under different plasma conditions are investigated in the range of RF power from 20 to 80 W. The membrane synthesized at 50 W shows better cell performance that it develops 610 mW cm{sup −2} of power density and 0.68 A cm{sup −2} of current density at 0.6 volts in fuel cell than other membranes synthesized at different plasma conditions.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Sputter-Deposited Mo Thin Films: Multimodal Characterization of Structure, Surface Morphology, Density, Residual Stress, Electrical Resistivity, and Mechanical Response

Multimodal datasets of materials are rich sources of information which can be leveraged for expedited discovery of process–structure–property relationships and for designing materials with targeted structures and/or properties. For this data descriptor article, we provide a multimodal dataset of magnetron sputter-deposited molybdenum (Mo) thin films, which are used in a variety of industries including high temperature coatings, photovoltaics, and microelectronics. In this dataset we explored a process space consisting of 27 unique combinations of sputter power and Ar deposition pressure. Here, the phase, structure, surface morphology, and composition of the Mo thin films were characterized by x-ray diffraction, scanning electron microscopy, atomic force microscopy, and Rutherford backscattering spectrometry. Physical properties—namely, thickness, film stress and sheet resistance—were also measured to provide additional film characteristics and behaviors. Additionally, nanoindentation was utilized to obtain mechanical load-displacement data. The entire dataset consists of 2072 measurements including scalar values (e.g., film stress values), 2D linescans (e.g., x-ray diffractograms), and 3D imagery (e.g., atomic force microscopy images). An additional 1889 quantities, including film hardness, modulus, electrical resistivity, density, and surface roughness, were derived from the experimental datasets using traditional methods. Minimal analysis and discussion of the results are provided in this data descriptor article to limit the authors’ preconceived interpretations of the data. Overall, the data modalities are consistent with previous reports of refractory metal thin films, ensuring that a high-quality dataset was generated. The entirety of this data is committed to a public repository in the Materials Data Facility.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Ghost states and surface structures of the charge density wave kagome metal ScV 6 Sn 6

In this work, we investigate the high-temperature phase of the kagome metal ScV 6 Sn 6 using scanning tunneling microscopy/spectroscopy (STM/S) and density functional theory calculations. STM topographic images of the cleaved sample reveal two distinct surface terminations: flat islands with Sn termination and trenches terminated by kagome layers with Sn as the outermost atomic layer. STS measurements on the Sn-terminated and kagome-terminated surfaces show significant differences, in particular the presence of large density of states near the Fermi level in the former case. Our first-principles calculations reveal that the charge density on the kagome-terminated surface gives rise to “ghost states” which show intensity away from surface atoms, arising due to hybridization of orbitals above the surface. These states can obscure the intrinsic properties of the surface, potentially leading to misattribution of the surface termination. This underscores the need for careful interpretation in STM studies, especially when discerning surface states of localized states. Understanding the surface structure of this versatile quantum material provides essential information for interpreting surface-sensitive experiments, tailoring material properties, engineering interfaces, and controlling stability and reactivity. This knowledge paves the way for further exploration and potential applications of kagome lattice materials in various fields, including quantum computing, topological physics, and advanced electronic devices.

36 MATERIALS SCIENCE↗
DOE OSTI2017

A Two-Dimensional Manganese Gallium Nitride Surface Structure Showing Ferromagnetism at Room Temperature

Practical applications of semiconductor spintronic devices necessitate ferromagnetic behavior at or above room temperature. In this paper we demonstrate a two-dimensional manganese gallium nitride surface structure (MnGaN-2D) which is atomically thin and shows ferromagnetic domain structure at room temperature as measured by spin-resolved scanning tunneling microscopy and spectroscopy. Application of small magnetic fields proves that the observed magnetic domains follow a hysteretic behavior. Two initially oppositely-oriented MnGaN-2D domains are rotated into alignment with only 120 mT and remain mostly in alignment at remanence. Additionally, the measurements are further supported by first-principles theoretical calculations which reveal highly spin-polarized and spin-split surface states, with spin polarization of up to 95% for manganese partial density of states.

36 MATERIALS SCIENCE↗
DOE OSTI2026

From bulk to surface: Structure and dynamics of amorphous alumina from deep potential molecular dynamics

Understanding the atomic-scale structure and dynamics of amorphous oxide surfaces is essential for interpreting their chemical reactivity, mechanical stability, and interfacial behavior, yet direct experimental characterization remains challenging. We employ Deep Potential (DP) molecular dynamics to generate large-scale, ab initio -quality models of amorphous Al 2 O 3 bulk glasses and melt-quenched free surfaces, enabling a quantitative analysis of both structure and relaxation dynamics with statistical confidence inaccessible to direct ab initio simulation. The trained DP model reproduces experimental liquid and glass structure, captures the cooling-rate dependence of the bulk glass transition, and corrects systematic biases in the polyhedral populations predicted by widely used classical force fields. At the free surface, mass density recovers to bulk values over ~10 Å, while local coordination requires a slightly wider subsurface region to fully converge. The outermost layer is oxygen-enriched, exhibits altered polyhedral connectivity with contracted Al–O bonds, and hosts a broad population of under-coordinated motifs (notably AlO 3 and OAl 2 ) whose abundances are governed by glass stability. These under-coordinated surface motifs exhibit distinct vibrational signatures and occur as locally paired Lewis acid and Brønsted base sites consistent with bond-valence compensation, yet remain spatially dispersed rather than aggregating into extended clusters. Despite this pronounced structural heterogeneity, surface relaxation and the glass-transition temperature remain comparable to their bulk counterparts, suggesting that the disordered surface is kinetically stable once formed. Together, these results establish a molecular-level picture of amorphous alumina surfaces and demonstrate the capability of machine-learned potentials to resolve structure–property relationships in disordered oxide interfaces.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

In-Situ Observation of the Formation of Laser-Induced Periodic Surface Structures with Extreme Spatial and Temporal Resolution

Irradiation of solid surfaces with intense ultrashort laser pulses represents a unique way of depositing energy into materials. It allows to realize states of extreme electronic excitation and/or very high temperature and pressure and to drive materials close to and beyond fundamental stability limits. As a consequence, structural changes and phase transitions often occur along unusual pathways and under strongly nonequilibrium conditions. Furthermore, due to the inherent multiscale nature—both temporally and spatially—of these irreversible processes, their direct experimental observation requires techniques that combine high temporal resolution with the appropriate spatial resolution and the capability to obtain good quality data on a single pulse/event basis. In this respect, fourth-generation light sources, namely, short wavelength and short pulse free electron lasers (FELs), are offering new and fascinating possibilities. As an example, this chapter will discuss the results of scattering experiments carried out at the FLASH free electron laser at DESY (Hamburg, Germany), which allowed us to resolve laser-induced structure formation at surfaces on the nanometer to submicron length scale and in temporal regimes ranging from picoseconds to several nanoseconds with sub-picosecond resolution.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗