Search NASA⌕ Search

SEARCH · Search NASA

Results for “surface tension”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

Contact angle and surface tension measurements of a five-ring polyphenyl ether

Contact angle measurements were performed for a five-ring polyphenyl ether isomeric mixture on M-50 steel in a dry nitrogen atmosphere. Two different techniques were used: (1) a tilting plate apparatus, and (2) a sessile drop apparatus. Measurements were made for the temperature range 25 to 190 C. Surface tension was measured by a differential maximum bubble pressure technique over the range 23 to 220 C in room air. The critical surface energy of spreading (gamma /sub c/) was determined for the polyphenyl ether by plotting the cosine of the contact angle (theta) versus the surface tension (gamma /sub LV/). The straight line intercept at cosine theta = 1 is defined as gamma (sub c). Gamma (sub c) was found to be 30.1 dyn/cm for the tilting plate technique and 31.3 dyn/cm for the sessile drop technique. These results indicate that the polyphenyl ether is inherently autophobic (i.e., it will not spread on its own surface film until its surface tension is less than gamma /sub c/). This phenomenon is discussed in light of the wettability and wear problems encountered with this fluid.

Jones, W. R., Jr.↗
NASA NTRS1976

Surface tension propellant control for Viking 75 Orbiter

The paper describes the selection, development and qualification of the surface tension system and includes results of low-g drop tower tests of scale models, 1-g simulation tests of low-g large ullage settling and liquid withdrawal, structural qualification tests, and propellant surface tension/contact angle studies. Subscale testing and analyses were used to evaluate the ability of the system to maintain or recover the desired propellant orientation following possible disturbances during the Viking mission. This effort included drop tower tests to demonstrate that valid wick paths exist for moving any displaced propellant back over the tank outlet. Variations in surface tension resulting from aging, temperature, and lubricant contamination were studied and the effects of surface finish, referee fluid exposure, aging, and lubricant contamination on contact angle were assessed. Results of movies of typical subscale drop tower tests and full scale slosh tests are discussed.

Dowdy, M. W.↗
NASA NTRS1988

Acoustic containerless experiment system: A non-contact surface tension measurement

The Acoustic Containerless Experiment System (ACES) was flown on STS 41-B in February 1984 and was scheduled to be reflown in 1986. The primary experiment that was to be conducted with the ACES module was the containerless melting and processing of a fluoride glass sample. A second experiment that was to be conducted was the verification of a non-contact surface tension measurement technique using the molten glass sample. The ACES module consisted of a three-axis acoustic positioning module that was inside an electric furnace capable of heating the system above the melting temperature of the sample. The acoustic module is able to hold the sample with acoustic forces in the center of the chamber and, in addition, has the capability of applying a modulating force on the sample along one axis of the chamber so that the molten sample or liquid drop could be driven into one of its normal oscillation modes. The acoustic module could also be adjusted so that it could place a torque on the molten drop and cause the drop to rotate. In the ACES, a modulating frequency was applied to the drop and swept through a range of frequencies that would include the n = 2 mode. A maximum amplitude of the drop oscillation would indicate when resonance was reached and from that data the surface tension could be calculated. For large viscosity samples, a second technique for measuring surface tension was developed. The results of the ACES experiment and some of the problems encountered during the actual flight of the experiment will be discussed.

Elleman, D. D.↗
NASA NTRS2024

Measuring the Density, Viscosity, and Surface Tension of Molten Titanates Using Electrostatic Levitation in Microgravity

Rare earth and barium titanates are useful as ferroelectric, dielectric, and optical materials. Measurements of their thermophysical properties in the liquid state can help guide melt processing technologies for their manufacture and advance understanding of fragile liquids' behavior and glass formation. Here, we report the density, thermal expansion, viscosity, and surface tension of molten BaTiNsub>2 O 5 , BaTi 4 O 9 , and 83TiO 2 -17RE 2 O 3 (RE = La or Nd). Measurements were made using electrostatic levitation and droplet oscillation techniques in microgravity, which provide access to quiescent liquid droplets and deep supercooling of 510–815 K below the equilibrium melting points. Densities were measured over 900–2400 K. Viscosities were similar for all four compositions, increasing from ∼10 mPa s near 2100 K to ∼30 mPa s near 1750 K. Surface tensions were 450–490 dyn cm −1 for the rare earth titanates and 383–395 dyn cm−1 for the barium titanates; surface tensions of all compositions had small or negligible temperature dependence over 1700–2200 K. For solids recovered after melt quenching, x-ray microtomography revealed the fracture mechanics in crystalline products and minimal internal porosity in glass products, likely arising from entrapped gas bubbles. Internal microstructures were generally similar for products processed either in microgravity or in a terrestrial aerodynamic levitator.

Stephen K Wilke↗
NASA NTRS1976

Analysis of surface tension driven flow in floating zone melting

Surface tension driven flow in a cylindrical melt suspended between two rods was investigated by numerical solution of the steady state differential equations for heat and momentum transfer. Radiation heating and electron beam heating were considered approximately. For small values of the driving force, one rotating ring was formed in the top half of the zone, and its mirror image in the bottom half. At larger driving forces, secondary cells form which probably would undergo oscillatory motion. The influence of Prandtl number, zone movement, and buoyancy on the convection was also studied. The primary resistance to mass transfer in the laminar regime was in the center of the zone rather than at the solid-liquid interfaces.

Chang, C. E.↗
NASA NTRS1981

Surface tension of natural silicate melts from 1,200-1,500 C and implications for melt structure

The surface tension between silicate liquid and gas is measured for four lava compositions (limburgite to andesite) from 1,200 to 1,500 C. It is noted that the magnitude of surface tension (gamma) is in the range 350-370 dynes/cm. Variations found in gamma as a function of liquid composition are small and have no obvious relation to liquid composition. Gamma is also found to vary little with furnace atmosphere - air, Ar, CO2, H2, CO and their mixtures. It is found that a relaxation time of hours to days, depending on temperature, is required before reproducible results can be obtained from originally crystalline starting material. The reproducible temperature dependence of gamma for complex silicate liquid solution is found to be small, positive, and a relatively simple function of liquid composition.

Walker, D.↗
NASA NTRS1999

Dynamic Nucleation of Supercooled Melts and Measurement of the Surface Tension and Viscosity

We investigate the phenomenon of acoustic pressure-induced nucleation by using a novel approach involving the large amplitude resonant radial oscillations and collapse of a single bubble intentionally injected into a supercooled liquid. Using a combination of previously developed and proven techniques, the bubble is suspended in a fluid host by an ultrasonic field which supplies both the levitation capability as well as the forcing of the radial oscillations. We observe the effects of an increase in pressure (due to bubble collapse) in a region no larger than 100 microns within the supercooled melt to rigorously probe the hypothesis of pressure-induced nucleation of the solid phase. The use of single bubbles operating in narrow temporal and spatial scales will allow the direct and unambiguous correlation between the origin and location of the generation of the disturbance and the location and timing of the nucleation event. In a companion research effort, we are developing novel techniques for the non-contact measurements of the surface tension and viscosity of highly viscous supercooled liquids. Currently used non-invasive methods of surface tension measurement for the case of undercooled liquids generally rely of the quantitative determination of the resonance frequencies of drop shape oscillations, of the dynamics of surface capillary waves, or of the velocity of streaming flows. These methods become quickly ineffective when the liquid viscosity rises to a significant value. An alternate and accurate method which would be applicable to liquids of significant viscosity is therefore needed. We plan to develop such a capability by measuring the equilibrium shape of levitated undercooled melt droplets as they undergo solid-body rotation. The experimental measurement of the characteristic point of transition (bifurcation point) between axisymmetric and two-lobed shapes will be used to calculate the surface tension of the liquid. Such an approach has already been validated through the experimental verification of numerical modeling results. The experimental approach involves levitation, melting, and solidification of undercooled droplets using a hybrid ultrasonic-electrostatic technique in both a gaseous as well as a vacuum environment. A shape relaxation method will be investigated in order to derive a reliable method to measure the viscosity of undercooled melts. The analysis of the monotonic relaxation to equilibrium shape of a drastically deformed and super-critically damped free drop has been used to derive interfacial tension of immiscible liquid combinations where one of the component has high viscosity. A standard approach uses the initial elongation of a droplet through shear flows, but an equivalent method could involve the initial deformation of a drop levitated in a gas by ultrasonic radiation pressure, electric stresses, or even solid body rotation. The dynamic behavior of the free drop relaxing back to equilibrium shape will be modeled, and its characteristic time dependence should provide a quantitative means to evaluate the liquid viscosity.

Trinh, E. H.↗
DOE OSTI2024

Implementation of Surface Tension on a Reacting Flow Solver, PeleLM: Preprint

In liquid rocket engines, the fuel is supplied to the combustion chamber in the liquid state though injectors. Such fuel undergoes atomization, vaporization, and combustion processes. To design reliable and efficient injectors, it is required to understand the full processes. This research is part of an effort to develop a full atomization-vaporization-combustion solver from first principles. As an initial step to tackle the atomization process, a multiphase flow solver is under development. For the development, a library of the volume of fluid scheme for multiphase, IRL is coupled with a reacting Navier-Stokes equation solver, PeleLM. Furthermore, as the surface tension has considerable effects on spray breakup. surface tension is implemented in the momentum equation using the continuum surface force model and the improved height function technique.

height function↗
NASA NTRS2002

Wetting Angles and Surface Tension of Ge(1-x)Si(x) Melts on Different Substrate Materials

The wetting angles and the surface tension of Ge(1-x)Si(x) melts (0.02 less than x less than 0.13) have been measured on various substrate materials using the sessile drop technique. Fused quartz, sapphire, SiC, glassy carbon, pBN, AIN, and Si3N4 have been used as substrates. The highest and most stable wetting angles were found for pBN substrates with 164 +/- 8 deg., either under forming gas with an additional carbon getter in the system or under active vacuum. The surface tension measurements resulted in a value of +2.2 x 10(exp -3) N/m.at%Si for the concentration dependence delta(gamma)/(delta)C. For the composition range measured, the temperature dependence (delt)gamma/(delta)T showed values similar to those of pure Ge, on average -0.07 x 10(exp -3) N/mK.

Croell, A.↗
NASA NTRS1984

Surface tension of ZrF4-BaF2-LaF3 glass

A solidified pendant drop technique is presently used in the measurement of surface tension of a 62 mol pct ZrF4, 33 mol pct BaF2, 5 mol pct LaF3 heavy metal-fluoride glass, in keeping with a requirement from a comparison experiment planned for microgravity conditions aboard the Space Shuttle. The surface tension at 550 C is 0.174 + or - 0.005 J/sq m.

Bansal, N. P.↗
NASA NTRS1979

Surface tension driven convection

In a normal gravitational environment, the free surface of a liquid in a container plays a passive role in the transport processes. However, at microgravity, the free surface can become the dominant factor. A simple but meaningful spaceflight experiment is proposed to investigate the nature and extent of flows induced by surface-tension gradients along the free surface. The influences of container geometry, wetability, contamination, and imposed heating modes will be investigated.

Ostrach, S.↗
NASA NTRS1998

Convective Instability of a Gravity Modulated Fluid Layer with Surface Tension Variation

Gravity modulation of an unbounded fluid layer with surface tension variations along its free surface is investigated. In parameter space of (wavenumber, Marangoni number) modulation has a destabilizing effect on the unmodulated neutral stability curve for large Prandtl number, Pr, and small modulation frequency, Omega, while a stabilizing effect is observed for small Pr and large Omega. As Omega yields infinity, the modulated neutral stability curves approach the unmodulated neutral stability curve. At certain values of Pr and L2 multiple minima are observed and the neutral stability curves become highly distorted. Closed regions of subharmonic instability are also observed. Alternating regions of synchronous and subharmonic instability separated by very thin stable regions are observed in (1/Omega,g(sub 1)) space for the singly diffusive cases. Quasiperiodic behavior in addition to the synchronous and subharmonic responses, are observed for the case of a double diffusive fluid layer. Minimum acceleration amplitudes were observed to closely correspond with a subharmonic response, Lambda(sub im) = Omega/2 .

Skarda, J. Raymond Lee↗
NASA NTRS1996

Dynamical Modeling of Surface Tension

In a recent review it is said that free-surface flows 'represent some of the difficult remaining challenges in computational fluid dynamics'. There has been progress with the development of new approaches to treating interfaces, such as the level-set method and the improvement of older methods such as the VOF method. A common theme of many of the new developments has been the regularization of discontinuities at the interface. One example of this approach is the continuum surface force (CSF) formulation for surface tension, which replaces the surface stress given by Laplace's equation by an equivalent volume force. Here, we describe how CSF formulation might be made more useful. Specifically, we consider a derivation of the CSF equations from a minimization of surface energy as outlined by Jacqmin (1996). This reformulation suggests that if one eliminates the computation of curvature in terms of a unit normal vector, parasitic currents may be eliminated. For this reformulation to work, it is necessary that transition region thickness be controlled. Various means for this, in addition to the one discussed by Jacqmin (1996), are discussed.

Brackbill, Jeremiah U.↗
NASA NTRS1982

An experimental study of heat induced surface-tension driven flow

Laser Doppler anemometry, radiation thermometry, and time-lapse photography have been used to study heat induced surface-tension driven flows in silicone oil and Fluorinert FC-43 in large open containers. For silicone oil, the effect of the surface tension gradient on the velocity field was not apparent enough to be detected. Because of its high viscosity, the oil was insensitive to outside disturbances, and the flow was steady. In the case of FC-43, the fluid was noticeably influenced by outside disturbances, and the flow was unsteady. The work reported here is part of an effort to develop experimental techniques and select test fluids for future space experiments on fluid motion in materials processing.

Kamotani, Y.↗
NASA NTRS1998

Effect of Gravity on Surface Tension

Spectroscopic measurements of liquid-vapor interfaces are made in +/- 1-g environments to note the effect of gravity on surface tension. A slight increase is detected at -1-g0, but is arguably within the uncertainty of the measurement technique. An increased dependence of surface tension on the orientation and magnitude of the gravitational vector is anticipated as the critical point is approached.

Weislogel, M. M.↗
NASA NTRS1989

Infrared surface temperature measurements for the surface tension driven convection experiment

In support of the Surface Tension Driven Convection Experiment (STDCE), a planned space transportation system (STS) flight experiment, a commercially available infrared thermal imaging system is used to quantify the imposed thermal signature along the free surface. The system was tested and calibrated for the STDCE with ground-based equivalents of the STDCE hardware. Before using the system, consideration was given to the radiation characteristics of the target (silicone oil). Absorption coefficients were calculated to understand the surface depth as seen by the imager and the penetration depth of the surface heater (CO2 laser). The performance and operational specifications for the imager and image processing system are described in detail to provide an understanding of the equipment. Measurements made with the system were compared to thermocouple measurements and a calculated surface temperature distribution. This comparison showed that in certain regions the IR imager measurements were within 5 percent of the overall temperature difference across the free surface. In other regions the measurements were within + or - 10 percent of the overall temperature gradient across the free surface. The effective emissivity of silicone oil for these experimental conditions was also determined. Measurement errors and their possible solutions are discussed.

Pline, Alexander D.↗