SEARCH · Search NASA

Results for “tire”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Experimental investigation of the cornering characteristics of 18 by 5.5, type 7, aircraft tires with different tread patterns

The characteristics, which include the cornering-force and drag-force friction coefficients and self-alining torque, were obtained on dry, damp, and flooded runway surfaces over a range of yaw angles from 0 deg to 12 deg and at ground speeds from approximately 5 to 90 knots. The results indicate that a tread pattern with pinholes in the ribs reduces the tire cornering capability at high yaw angles on a damp surface but improves cornering on a dry surface. A tread pattern which has transverse grooves across the entire width of the tread improves the tire cornering performance slightly at high speeds on the flooded runway surface. The cornering capability of all the tires is degraded at high ground speeds by thin film lubrication and/or tire hydroplaning effects. Alterations to the conventional tread pattern provide only marginal improvements in the tire cornering capability which suggests that runway surface treatments may be a more effective way of improving aircraft ground performance during wet operations.

Dreher, R. C.↗

NASA NTRS1976

Thermal conductance of and heat generation in tire-pavement interface and effect on aircraft braking

A finite-difference analysis was performed on temperature records obtained from a free rolling automotive tire and from pavement surface. A high thermal contact conductance between tire and asphalt was found on a statistical basis. Average slip due to squirming between tire and asphalt was about 1.5 mm. Consequent friction heat was estimated as 64 percent of total power absorbed by bias-ply, belted tire. Extrapolation of results to aircraft tire indicates potential braking improvement by even moderate increase of heat absorbing capacity of runway surface.

Miller, C. D.↗

NASA NTRS1980

Tire-pressure measuring concept

External tire-pressure measuring concept involves device that applies external load to tire wall to measure its internal pressure. Method promises to be faster than conventional tire-pressure checks, speeding up turnaround time for aircraft. Method prevents air leakage that occurs when pressure is measured through tire valve. Device is used to measure tire pressures on land vehicles.

Ashmore, L. O.↗

NASA NTRS1981

Cornering characteristics of the nose-gear tire of the space shuttle orbiter

An experimental investigation was conducted to evaluate cornering characteristics of the 32 x 8.8 nose gear tire of the space shuttle orbiter. Data were obtained on a dry concrete runway at nominal ground speeds ranging from 50 to 100 knots and over a range of tire vertical loads and yaw angles which span the expected envelope of loads and yaw angles to be encountered during space shuttle landing operations. The cornering characteristics investigated included side and drag forces and friction coefficients, aligning and overturning torques, friction force moment arm, and the lateral center of pressure shift. Results of this investigation indicate that the cornering characteristics of the space shuttle nose gear tire are insensitive to variations in ground speed over the range tested. The effects on cornering characteristics of variations in the tire vertical load and yaw angle are as expected. Trends observed are consistent with trends observed during previous cornering tests involving other tire sizes.

Vogler, W. A.↗

NASA NTRS1983

Application of tire dynamics to aircraft landing gear design analysis

The tire plays a key part in many analyses used for design of aircraft landing gear. Examples include structural design of wheels, landing gear shimmy, brake whirl, chatter and squeal, complex combination of chatter and shimmy on main landing gear (MLG) systems, anti-skid performance, gear walk, and rough terrain loads and performance. Tire parameters needed in the various analyses are discussed. Two tire models are discussed for shimmy analysis, the modified Moreland approach and the von Schlippe-Dietrich approach. It is shown that the Moreland model can be derived from the Von Schlippe-Dietrich model by certain approximations. The remaining analysis areas are discussed in general terms and the tire parameters needed for each are identified. Accurate tire data allows more accurate design analysis and the correct prediction of dynamic performance of aircraft landing gear.

Black, R. J.↗

NASA NTRS1984

Heat generation in aircraft tires under braked rolling conditions

An analytical model was developed to approximate the internal temperature distribution in an aircraft tire operating under conditions of unyawed braked rolling. The model employs an array of elements to represent the tire cross section and considers the heat generated within the tire to be caused by the change in strain energy associated with cyclic tire deflection. The additional heating due to tire slip and stresses induced by braking are superimposed on the previously developed free rolling model. An extensive experimental program was conducted to verify temperatures predicted from the analytical model. Data from these tests were compared with calculations over a range of operating conditions. The model results were in reasonably good agreement with measured values.

Clark, S. K.↗

NASA NTRS1987

Cornering and wear behavior of the Space Shuttle Orbiter main gear tire

One of the factors needed to describe the handling characteristics of the Space Shuttle Orbiter during the landing rollout is the response of the vehicle's tires to variations in load and yaw angle. An experimental investigation of the cornering characteristics of the Orbiter main gear tires was conducted at the NASA Langley Research Center Aircraft Landing Dynamics Facility. This investigation compliments earlier work done to define the Orbiter nose tire cornering characteristics. In the investigation, the effects of load and yaw angle were evaluated by measuring parameters such as side load and drag load, and obtaining measurements of aligning torque. Because the tire must operate on an extremely rough runway at the Shuttle Landing Facility at Kennedy Space Center (KSC), tests were also conducted to describe the wear behavior of the tire under various conditions on a simulated KSC runway surface. Mathematical models for both the cornering and the wear behavior are discussed.

Daugherty, Robert H.↗

NASA NTRS1989

Cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire

Tests of the Space Shuttle Orbiter nose-gear tire have been completed at NASA Langley's Aircraft Landing Dynamics Facility. The purpose of these tests was to determine the cornering and wear characteristics of the Space Shuttle Orbiter nose-gear tire under realistic operating conditions. The tire was tested on a simulated Kennedy Space Center runway surface at speeds from 100 to 180 kts. The results of these tests defined the cornering characteristics which included side forces and associated side force friction coefficient over a range of yaw angles from 0 deg to 12 deg. Wear characteristics were defined by tire tread and cord wear over a yaw angle range of 0 deg to 4 deg under dry and wet runway conditions. Wear characteristics were also defined for a 15 kt crosswind landing with two blown right main-gear tires and nose-gear steering engaged.

Davis, Pamela A.↗

NASA NTRS1991

Analytical studies of the Space Shuttle orbiter nose-gear tire

A computational procedure is presented for evaluating the analytic sensitivity derivatives of the tire response with respect to material and geometrical properties of the tire. The tire is modeled by using a two-dimensional laminated anisotropic shell theory with the effects of variation in material and geometric parameters included. The computational procedure is applied to the case of the Space Shuttle orbiter nose-gear tire subjected to uniform inflation pressure. Numerical results are presented which show the sensitivity of the different tire response quantities to variations in the material characteristics of both the cord and rubber.

Noor, Ahmed K.↗

NASA NTRS1993

Remote tire pressure sensing technique

A remote tire pressure sensing technique is provided which uses vibration frequency to determine tire pressure. A vibration frequency measuring device is attached to the external surface of a tire which is then struck with an object, causing the tire to vibrate. The frequency measuring device measures the vibrations and converts the vibrations into corresponding electrical impulses. The electrical impulses are then fed into the frequency analyzing system which uses the electrical impulses to determine the relative peaks of the vibration frequencies as detected by the frequency measuring device. The measured vibration frequency peaks are then compared to predetermined data describing the location of vibration frequency peaks for a given pressure, thereby determining the air pressure of the tire.

Robinson, Howard H.↗

NASA NTRS1995

Reduction technique for tire contact problems

A reduction technique and a computational procedure are presented for predicting the tire contact response and evaluating the sensitivity coefficients of the different response quantities. The sensitivity coefficients measure the sensitivity of the contact response to variations in the geometric and material parameters of the tire. The tire is modeled using a two-dimensional laminated anisotropic shell theory with the effects of variation in geometric and material parameters, transverse shear deformation, and geometric nonlinearities included. The contact conditions are incorporated into the formulation by using a perturbed Lagrangian approach with the fundamental unknowns consisting of the stress resultants, the generalized displacements, and the Lagrange multipliers associated with the contact conditions. The elemental arrays are obtained by using a modified two-field, mixed variational principle. For the application of the reduction technique, the tire finite element model is partitioned into two regions. The first region consists of the nodes that are likely to come in contact with the pavement, and the second region includes all the remaining nodes. The reduction technique is used to significantly reduce the degrees of freedom in the second region. The effectiveness of the computational procedure is demonstrated by a numerical example of the frictionless contact response of the space shuttle nose-gear tire, inflated and pressed against a rigid flat surface.

Noor, Ahmed K.↗

NASA NTRS1995

Computational strategies for tire monitoring and analysis

Computational strategies are presented for the modeling and analysis of tires in contact with pavement. A procedure is introduced for simple and accurate determination of tire cross-sectional geometric characteristics from a digitally scanned image. Three new strategies for reducing the computational effort in the finite element solution of tire-pavement contact are also presented. These strategies take advantage of the observation that footprint loads do not usually stimulate a significant tire response away from the pavement contact region. The finite element strategies differ in their level of approximation and required amount of computer resources. The effectiveness of the strategies is demonstrated by numerical examples of frictionless and frictional contact of the space shuttle Orbiter nose-gear tire. Both an in-house research code and a commercial finite element code are used in the numerical studies.

Danielson, Kent T.↗

NASA NTRS1995

Advances in reduction techniques for tire contact problems

Some recent developments in reduction techniques, as applied to predicting the tire contact response and evaluating the sensitivity coefficients of the different response quantities, are reviewed. The sensitivity coefficients measure the sensitivity of the contact response to variations in the geometric and material parameters of the tire. The tire is modeled using a two-dimensional laminated anisotropic shell theory with the effects of variation in geometric and material parameters, transverse shear deformation, and geometric nonlinearities included. The contact conditions are incorporated into the formulation by using a perturbed Lagrangian approach with the fundamental unknowns consisting of the stress resultants, the generalized displacements, and the Lagrange multipliers associated with the contact conditions. The elemental arrays are obtained by using a modified two-field, mixed variational principle. For the application of reduction techniques, the tire finite element model is partitioned into two regions. The first region consists of the nodes that are likely to come in contact with the pavement, and the second region includes all the remaining nodes. The reduction technique is used to significantly reduce the degrees of freedom in the second region. The effectiveness of the computational procedure is demonstrated by a numerical example of the frictionless contact response of the space shuttle nose-gear tire, inflated and pressed against a rigid flat surface. Also, the research topics which have high potential for enhancing the effectiveness of reduction techniques are outlined.

Noor, Ahmed K.↗

NASA NTRS1997

Quasi-Static and Dynamic Response Characteristics of F-4 Bias-Ply and Radial-Belted Main Gear Tires

An investigation was conducted at Langley Research Center to determine the quasi-static and dynamic response characteristics of F-4 military fighter 30x11.5-14.5/26PR bias-ply and radial-belted main gear tires. Tire properties were measured by the application of vertical, lateral, and fore-and-aft loads. Mass moment-of-inertia data were also obtained. The results of the study include quasi-static load-deflection curves, free-vibration time-history plots, energy loss associated with hysteresis, stiffness and damping characteristics, footprint geometry, and inertia properties of each type of tire. The difference between bias-ply and radial-belted tire construction is given, as well as the advantages and disadvantages of each tire design. Three simple damping models representing viscous, structural, and Coulomb friction are presented and compared with the experimental data. The conclusions discussed contain a summary of test observations.

Davis, Pamela A.↗

NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Materials are a fundamental building block that often get overlooked as a critical component that shapes our world. Numerous products that impact our lives are enabled by the materials from which they are made. With regard to Martian and lunar rover applications, conventional mobility elements, such as pneumatic tires, suffer from a number of issues related to reliability. Two of the more prevalent problems are the high likelihood of single point failure owing to puncture (i.e. flat tire), and loss of efficiency due to reduction in tire pressure over time. Solid, rigid wheels suffer from the inability to handle the high, localized loads while encountering rugged terrain and also produce relatively poor traction and operating efficiency. In an effort to overcome these problems, non-pneumatic, compliant tire designs are being developed, using Nickel-Titanium (NiTi), a thermally activated shape memory alloy (SMA), that is less sensitive to temperature and exhibits much greater plastic deformation than do conventional vulcanized rubber pneumatic tires.

Padula, Santo, II↗

NASA NTRS2019

Utilizing Shape Memory Alloys for Novel, Non-Pneumatic Tire Design - Designing for the Best of Both Worlds

Padula, Santo, II↗

NASA NTRS1954

Determination of the elastic constants of airplane tires

For determination of the elastic constants of airplane tires which are required for the numerical calculations of the shimmy properties of nose and tail wheels, deformation measurements were carried out on four different tires. For this purpose, the tires were loaded in each case with a normal load and then with a lateral force, a tangential force, and a moment. Moreover, the weight and the mass moment of inertia about a vertical axis were determined for the various tires.

TIRES↗

NASA NTRS1955

Reduction of the shimmy tendency of tail and nose-wheel landing gears by installation of specially designed tires

Shimmy of tail and nose wheels may be eliminated by installation of dampers and use of large trail; however, this produces construction and operational disadvantages. It is more favorable to employ, instead of the customary tail-wheel tires, tires with lesser shimmy tendency. A description of the best possible form for these tires follows: furthermore, a few general concepts regarding the effects of the condition of the tire, of the type of rolling motion, and of the landing, are discussed.

WHEELS, TAIL - SHIMMYING↗